Merge tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM/arm64 Devicetree updates from Olof Johansson:
 "As usual, device tree updates is the bulk of our material in this
  merge window. This time around, 559 patches affecting both 32- and
  64-bit platforms.

  Changes are too many to list individually, but some of the larger
  ones:

  New platform/SoC support:

   - Automotive:
     + Renesas R-Car D3 (R8A77995)
     + TI DT76x
     + MediaTek mt2712e
   - Communication-oriented:
     + Qualcomm IPQ8074
     + Broadcom Stingray
     + Marvell Armada 8080
   - Set top box:
     + Uniphier PXs3

  Besides some vendor reference boards for the SoC above, there are also
  several new boards/machines:

   - TI AM335x Moxa UC-8100-ME-T open platform
   - TI AM57xx Beaglebone X15 Rev C
   - Microchip/Atmel sama5d27 SoM1 EK
   - Broadcom Raspberry Pi Zero W
   - Gemini-based D-Link DIR-685 router
   - Freescale i.MX6:
     + Toradex Apalis module + Apalis and Ixora carrier boards
     + Engicam GEAM6UL Starter Kit
   - Freescale i.MX53-based Beckhoff CX9020 Embedded PC
   - Mediatek mt7623-based BananaPi R2
   - Several Allwinner-based single-board computers:
  + Cubietruck plus
  + Bananapi M3, M2M and M64
  + NanoPi A64
  + A64-OLinuXino
  + Pine64
   - Rockchip RK3328 Pine64/Rock64 board support
   - Rockchip RK3399 boards:
  + RK3399 Sapphire module on Excavator carrier (RK3399 reference design)
  + Theobroma Systems RK3399-Q7 SoM
   - ZTE ZX296718 PCBOX Board"

* tag 'armsoc-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (559 commits)
  ARM: dts: at91: at91sam9g45: add AC97
  arm64: dts: marvell: mcbin: enable more networking ports
  arm64: dts: marvell: add a reference to the sysctrl syscon in the ppv2 node
  arm64: dts: marvell: add TX interrupts for PPv2.2
  arm64: dts: uniphier: add PXs3 SoC support
  ARM: dts: uniphier: add pinctrl groups of ethernet phy mode
  ARM: dts: uniphier: fix size of sdctrl nodes
  ARM: dts: uniphier: add AIDET nodes
  arm64: dts: uniphier: fix size of sdctrl node
  arm64: dts: uniphier: add AIDET nodes
  Revert "ARM: dts: sun8i: h3: Enable dwmac-sun8i on the Beelink X2"
  arm64: dts: uniphier: add reset controller node of analog amplifier
  arm64: dts: marvell: add Device Tree files for Armada-8KP
  arm64: dts: rockchip: add Haikou baseboard with RK3399-Q7 SoM
  arm64: dts: rockchip: add RK3399-Q7 (Puma) SoM
  dt-bindings: add rk3399-q7 SoM
  ARM: dts: rockchip: enable usb for rv1108-evb
  ARM: dts: rockchip: add usb nodes for rv1108 SoCs
  dt-bindings: update grf-binding for rv1108 SoCs
  ARM: dts: aspeed-g4: fix AHB window size of the SMC controllers
  ...

27 files changed, 303 insertions, 58 deletions

diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index 520cdd2127cf..4e4bc0bae597 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -1,6 +1,18 @@
 Amlogic MesonX device tree bindings
 -------------------------------------------
 
+Work in progress statement:
+
+Device tree files and bindings applying to Amlogic SoCs and boards are
+considered "unstable". Any Amlogic device tree binding may change at
+any time. Be sure to use a device tree binary and a kernel image
+generated from the same source tree.
+
+Please refer to Documentation/devicetree/bindings/ABI.txt for a definition of a
+stable binding/ABI.
+
+---------------------------------------------------------------
+
 Boards with the Amlogic Meson6 SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,meson6"
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
index 9c97de23919a..3e3efa046ac5 100644
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
@@ -42,6 +42,10 @@ Raspberry Pi Zero
 Required root node properties:
 compatible = "raspberrypi,model-zero", "brcm,bcm2835";
 
+Raspberry Pi Zero W
+Required root node properties:
+compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
+
 Generic BCM2835 board
 Required root node properties:
 compatible = "brcm,bcm2835";
diff --git a/Documentation/devicetree/bindings/arm/bhf.txt b/Documentation/devicetree/bindings/arm/bhf.txt
new file mode 100644
index 000000000000..886b503caf9c
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/bhf.txt
@@ -0,0 +1,6 @@
+Beckhoff Automation Platforms Device Tree Bindings
+--------------------------------------------------
+
+CX9020 Embedded PC
+Required root node properties:
+    - compatible = "bhf,cx9020", "fsl,imx53";
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index a44253cad269..b92f12bd5244 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -200,6 +200,7 @@ described below.
 			    "arm,realview-smp"
 			    "brcm,bcm11351-cpu-method"
 			    "brcm,bcm23550"
+			    "brcm,bcm2836-smp"
 			    "brcm,bcm-nsp-smp"
 			    "brcm,brahma-b15"
 			    "marvell,armada-375-smp"
diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt b/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt
new file mode 100644
index 000000000000..f3e9624534c6
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-8kp.txt
@@ -0,0 +1,15 @@
+Marvell Armada 8KPlus Platforms Device Tree Bindings
+----------------------------------------------------
+
+Boards using a SoC of the Marvell Armada 8KP families must carry
+the following root node property:
+
+ - compatible, with one of the following values:
+
+   - "marvell,armada-8080", "marvell,armada-ap810-octa", "marvell,armada-ap810"
+     when the SoC being used is the Armada 8080
+
+Example:
+
+compatible = "marvell,armada-8080-db", "marvell,armada-8080",
+	     "marvell,armada-ap810-octa", "marvell,armada-ap810"
diff --git a/Documentation/devicetree/bindings/arm/mediatek.txt b/Documentation/devicetree/bindings/arm/mediatek.txt
index da7bd138e6f2..91d517849483 100644
--- a/Documentation/devicetree/bindings/arm/mediatek.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek.txt
@@ -1,12 +1,12 @@
-MediaTek mt65xx, mt67xx & mt81xx Platforms Device Tree Bindings
+MediaTek SoC based Platforms Device Tree Bindings
 
-Boards with a MediaTek mt65xx/mt67xx/mt81xx SoC shall have the
-following property:
+Boards with a MediaTek SoC shall have the following property:
 
 Required root node property:
 
 compatible: Must contain one of
    "mediatek,mt2701"
+   "mediatek,mt2712"
    "mediatek,mt6580"
    "mediatek,mt6589"
    "mediatek,mt6592"
@@ -14,7 +14,8 @@ compatible: Must contain one of
    "mediatek,mt6795"
    "mediatek,mt6797"
    "mediatek,mt7622"
-   "mediatek,mt7623"
+   "mediatek,mt7623" which is referred to MT7623N SoC
+   "mediatek,mt7623a"
    "mediatek,mt8127"
    "mediatek,mt8135"
    "mediatek,mt8173"
@@ -25,6 +26,9 @@ Supported boards:
 - Evaluation board for MT2701:
     Required root node properties:
       - compatible = "mediatek,mt2701-evb", "mediatek,mt2701";
+- Evaluation board for MT2712:
+    Required root node properties:
+      - compatible = "mediatek,mt2712-evb", "mediatek,mt2712";
 - Evaluation board for MT6580:
     Required root node properties:
       - compatible = "mediatek,mt6580-evbp1", "mediatek,mt6580";
@@ -46,9 +50,11 @@ Supported boards:
 - Reference board variant 1 for MT7622:
     Required root node properties:
       - compatible = "mediatek,mt7622-rfb1", "mediatek,mt7622";
-- Evaluation board for MT7623:
+- Reference  board for MT7623n with NAND:
     Required root node properties:
-      - compatible = "mediatek,mt7623-evb", "mediatek,mt7623";
+      - compatible = "mediatek,mt7623n-rfb-nand", "mediatek,mt7623";
+- Bananapi BPI-R2 board:
+      - compatible = "bananapi,bpi-r2", "mediatek,mt7623";
 - MTK mt8127 tablet moose EVB:
     Required root node properties:
       - compatible = "mediatek,mt8127-moose", "mediatek,mt8127";
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index 9c6bebe43449..2ecc712bf707 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -157,6 +157,9 @@ Boards:
 - AM335X phyCORE-AM335x: Development kit
   compatible = "phytec,am335x-pcm-953", "phytec,am335x-phycore-som", "ti,am33xx"
 
+- AM335X UC-8100-ME-T: Communication-centric industrial computing platform
+  compatible = "moxa,uc-8100-me-t", "ti,am33xx";
+
 - OMAP5 EVM : Evaluation Module
   compatible = "ti,omap5-evm", "ti,omap5"
 
@@ -187,6 +190,9 @@ Boards:
 - AM5718 IDK
   compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7"
 
+- DRA762 EVM:  Software Development Board for DRA762
+  compatible = "ti,dra76-evm", "ti,dra762", "ti,dra7"
+
 - DRA742 EVM:  Software Development Board for DRA742
   compatible = "ti,dra7-evm", "ti,dra742", "ti,dra74", "ti,dra7"
 
diff --git a/Documentation/devicetree/bindings/arm/qcom.txt b/Documentation/devicetree/bindings/arm/qcom.txt
index 028d16e72186..0ed4d39d7fe1 100644
--- a/Documentation/devicetree/bindings/arm/qcom.txt
+++ b/Documentation/devicetree/bindings/arm/qcom.txt
@@ -25,6 +25,7 @@ The 'SoC' element must be one of the following strings:
 	msm8994
 	msm8996
 	mdm9615
+	ipq8074
 
 The 'board' element must be one of the following strings:
 
@@ -33,6 +34,7 @@ The 'board' element must be one of the following strings:
 	dragonboard
 	mtp
 	sbc
+	hk01
 
 The 'soc_version' and 'board_version' elements take the form of v<Major>.<Minor>
 where the minor number may be omitted when it's zero, i.e.  v1.0 is the same
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index 11c0ac4a2d56..b003148e2945 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -134,6 +134,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
      - compatible = "phytec,rk3288-pcm-947", "phytec,rk3288-phycore-som", "rockchip,rk3288";
 
+- Pine64 Rock64 board:
+    Required root node properties:
+    - compatible = "pine64,rock64", "rockchip,rk3328";
+
 - Rockchip PX3 Evaluation board:
     Required root node properties:
       - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
@@ -173,6 +177,14 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "rockchip,rk3399-evb", "rockchip,rk3399";
 
+- Rockchip RK3399 Sapphire Excavator board:
+    Required root node properties:
+      - compatible = "rockchip,rk3399-sapphire-excavator", "rockchip,rk3399";
+
+- Theobroma Systems RK3399-Q7 Haikou Baseboard:
+    Required root node properties:
+      - compatible = "tsd,rk3399-q7-haikou", "rockchip,rk3399";
+
 - Tronsmart Orion R68 Meta
     Required root node properties:
       - compatible = "tronsmart,orion-r68-meta", "rockchip,rk3368";
diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 1a671e329864..ae75cb3b1331 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -39,6 +39,8 @@ SoCs:
     compatible = "renesas,r8a7795"
   - R-Car M3-W (R8A77960)
     compatible = "renesas,r8a7796"
+  - R-Car D3 (R8A77995)
+    compatible = "renesas,r8a77995"
 
 
 Boards:
@@ -53,6 +55,8 @@ Boards:
     compatible = "renesas,blanche", "renesas,r8a7792"
   - BOCK-W
     compatible = "renesas,bockw", "renesas,r8a7778"
+  - Draak (RTP0RC77995SEB0010S)
+    compatible = "renesas,draak", "renesas,r8a77995"
   - Genmai (RTK772100BC00000BR)
     compatible = "renesas,genmai", "renesas,r7s72100"
   - GR-Peach (X28A-M01-E/F)
@@ -64,6 +68,10 @@ Boards:
     compatible = "renesas,h3ulcb", "renesas,r8a7795";
   - Henninger
     compatible = "renesas,henninger", "renesas,r8a7791"
+  - iWave Systems RZ/G1E SODIMM SOM Development Platform (iW-RainboW-G22D)
+    compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745"
+  - iWave Systems RZ/G1E SODIMM System On Module (iW-RainboW-G22M-SM)
+    compatible = "iwave,g22m", "renesas,r8a7745"
   - iWave Systems RZ/G1M Qseven Development Platform (iW-RainboW-G20D-Qseven)
     compatible = "iwave,g20d", "iwave,g20m", "renesas,r8a7743"
   - iWave Systems RZ/G1M Qseven System On Module (iW-RainboW-G20M-Qseven)
diff --git a/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt b/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt
index 207682647d33..b455c5aa9139 100644
--- a/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt
+++ b/Documentation/devicetree/bindings/clock/amlogic,meson8b-clkc.txt
@@ -16,18 +16,25 @@ Required Properties:
 	   mapped region.
 
 - #clock-cells: should be 1.
+- #reset-cells: should be 1.
 
 Each clock is assigned an identifier and client nodes can use this identifier
 to specify the clock which they consume. All available clocks are defined as
 preprocessor macros in the dt-bindings/clock/meson8b-clkc.h header and can be
 used in device tree sources.
 
+Similarly a preprocessor macro for each reset line is defined in
+dt-bindings/reset/amlogic,meson8b-clkc-reset.h (which can be used from the
+device tree sources).
+
+
 Example: Clock controller node:
 
 	clkc: clock-controller@c1104000 {
-		#clock-cells = <1>;
 		compatible = "amlogic,meson8b-clkc";
 		reg = <0xc1108000 0x4>, <0xc1104000 0x460>;
+		#clock-cells = <1>;
+		#reset-cells = <1>;
 	};
 
 
diff --git a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
index cb7ffc58c564..b1a8929c2536 100644
--- a/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
+++ b/Documentation/devicetree/bindings/display/bridge/renesas,dw-hdmi.txt
@@ -13,6 +13,7 @@ Required properties:
 
 - compatible : Shall contain one or more of
   - "renesas,r8a7795-hdmi" for R8A7795 (R-Car H3) compatible HDMI TX
+  - "renesas,r8a7796-hdmi" for R8A7796 (R-Car M3-W) compatible HDMI TX
   - "renesas,rcar-gen3-hdmi" for the generic R-Car Gen3 compatible HDMI TX
 
     When compatible with generic versions, nodes must list the SoC-specific
diff --git a/Documentation/devicetree/bindings/display/renesas,du.txt b/Documentation/devicetree/bindings/display/renesas,du.txt
index c6cb96a4fa93..4bbd1e9bf3be 100644
--- a/Documentation/devicetree/bindings/display/renesas,du.txt
+++ b/Documentation/devicetree/bindings/display/renesas,du.txt
@@ -36,8 +36,10 @@ Required Properties:
       When supplied they must be named "dclkin.x" with "x" being the input
       clock numerical index.
 
-  - vsps: A list of phandles to the VSP nodes that handle the memory
-    interfaces for the DU channels.
+  - vsps: A list of phandle and channel index tuples to the VSPs that handle
+    the memory interfaces for the DU channels. The phandle identifies the VSP
+    instance that serves the DU channel, and the channel index identifies the
+    LIF instance in that VSP.
 
 Required nodes:
 
@@ -59,24 +61,24 @@ corresponding to each DU output.
  R8A7796 (M3-W)	DPAD		HDMI		LVDS		-
 
 
-Example: R8A7790 (R-Car H2) DU
+Example: R8A7795 (R-Car H3) ES2.0 DU
 
-	du: du@feb00000 {
-		compatible = "renesas,du-r8a7790";
-		reg = <0 0xfeb00000 0 0x70000>,
-		      <0 0xfeb90000 0 0x1c>,
-		      <0 0xfeb94000 0 0x1c>;
-		reg-names = "du", "lvds.0", "lvds.1";
-		interrupt-parent = <&gic>;
-		interrupts = <0 256 IRQ_TYPE_LEVEL_HIGH>,
-			     <0 268 IRQ_TYPE_LEVEL_HIGH>,
-			     <0 269 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&mstp7_clks R8A7790_CLK_DU0>,
-		         <&mstp7_clks R8A7790_CLK_DU1>,
-		         <&mstp7_clks R8A7790_CLK_DU2>,
-		         <&mstp7_clks R8A7790_CLK_LVDS0>,
-		         <&mstp7_clks R8A7790_CLK_LVDS1>;
-		clock-names = "du.0", "du.1", "du.2", "lvds.0", "lvds.1";
+	du: display@feb00000 {
+		compatible = "renesas,du-r8a7795";
+		reg = <0 0xfeb00000 0 0x80000>,
+		      <0 0xfeb90000 0 0x14>;
+		reg-names = "du", "lvds.0";
+		interrupts = <GIC_SPI 256 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH>,
+			     <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cpg CPG_MOD 724>,
+			 <&cpg CPG_MOD 723>,
+			 <&cpg CPG_MOD 722>,
+			 <&cpg CPG_MOD 721>,
+			 <&cpg CPG_MOD 727>;
+		clock-names = "du.0", "du.1", "du.2", "du.3", "lvds.0";
+		vsps = <&vspd0 0>, <&vspd1 0>, <&vspd2 0>, <&vspd0 1>;
 
 		ports {
 			#address-cells = <1>;
@@ -89,12 +91,19 @@ Example: R8A7790 (R-Car H2) DU
 			};
 			port@1 {
 				reg = <1>;
-				du_out_lvds0: endpoint {
+				du_out_hdmi0: endpoint {
+					remote-endpoint = <&dw_hdmi0_in>;
 				};
 			};
 			port@2 {
 				reg = <2>;
-				du_out_lvds1: endpoint {
+				du_out_hdmi1: endpoint {
+					remote-endpoint = <&dw_hdmi1_in>;
+				};
+			};
+			port@3 {
+				reg = <3>;
+				du_out_lvds0: endpoint {
 				};
 			};
 		};
diff --git a/Documentation/devicetree/bindings/dma/ti-edma.txt b/Documentation/devicetree/bindings/dma/ti-edma.txt
index 33d9e386dc45..41f0c1a07c56 100644
--- a/Documentation/devicetree/bindings/dma/ti-edma.txt
+++ b/Documentation/devicetree/bindings/dma/ti-edma.txt
@@ -9,7 +9,12 @@ execute the actual DMA tansfer.
 eDMA3 Channel Controller
 
 Required properties:
-- compatible:	"ti,edma3-tpcc" for the channel controller(s)
+--------------------
+- compatible:	Should be:
+		- "ti,edma3-tpcc" for the channel controller(s) on OMAP,
+		  AM33xx and AM43xx SoCs.
+		- "ti,k2g-edma3-tpcc", "ti,edma3-tpcc" for the
+		  channel controller(s) on 66AK2G.
 - #dma-cells:	Should be set to <2>. The first number is the DMA request
 		number and the second is the TC the channel is serviced on.
 - reg:		Memory map of eDMA CC
@@ -19,8 +24,19 @@ Required properties:
 - ti,tptcs:	List of TPTCs associated with the eDMA in the following form:
 		<&tptc_phandle TC_priority_number>. The highest priority is 0.
 
+SoC-specific Required properties:
+--------------------------------
+The following are mandatory properties for OMAP, AM33xx and AM43xx SoCs only:
+- ti,hwmods:	Name of the hwmods associated to the eDMA CC.
+
+The following are mandatory properties for 66AK2G SoCs only:
+- power-domains:Should contain a phandle to a PM domain provider node
+		and an args specifier containing the device id
+		value. This property is as per the binding,
+		Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
+
 Optional properties:
-- ti,hwmods:	Name of the hwmods associated to the eDMA CC
+-------------------
 - ti,edma-memcpy-channels: List of channels allocated to be used for memcpy, iow
 		these channels will be SW triggered channels. See example.
 - ti,edma-reserved-slot-ranges: PaRAM slot ranges which should not be used by
@@ -31,17 +47,34 @@ Optional properties:
 eDMA3 Transfer Controller
 
 Required properties:
-- compatible:	"ti,edma3-tptc" for the transfer controller(s)
+--------------------
+- compatible:	Should be:
+		- "ti,edma3-tptc" for the transfer controller(s) on OMAP,
+		  AM33xx and AM43xx SoCs.
+		- "ti,k2g-edma3-tptc", "ti,edma3-tptc" for the
+		  transfer controller(s) on 66AK2G.
 - reg:		Memory map of eDMA TC
 - interrupts:	Interrupt number for TCerrint.
 
+SoC-specific Required properties:
+--------------------------------
+The following are mandatory properties for OMAP, AM33xx and AM43xx SoCs only:
+- ti,hwmods:	Name of the hwmods associated to the eDMA TC.
+
+The following are mandatory properties for 66AK2G SoCs only:
+- power-domains:Should contain a phandle to a PM domain provider node
+		and an args specifier containing the device id
+		value. This property is as per the binding,
+		Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
+
 Optional properties:
-- ti,hwmods:	Name of the hwmods associated to the given eDMA TC
+-------------------
 - interrupt-names: "edma3_tcerrint"
 
 ------------------------------------------------------------------------------
-Example:
+Examples:
 
+1.
 edma: edma@49000000 {
 	compatible = "ti,edma3-tpcc";
 	ti,hwmods = "tpcc";
@@ -108,6 +141,58 @@ mcasp0: mcasp@48038000 {
 	dma-names = "tx", "rx";
 };
 
+2.
+edma1: edma@02728000 {
+	compatible = "ti,k2g-edma3-tpcc", "ti,edma3-tpcc";
+	reg =	<0x02728000 0x8000>;
+	reg-names = "edma3_cc";
+	interrupts = <GIC_SPI 208 IRQ_TYPE_EDGE_RISING>,
+			<GIC_SPI 219 IRQ_TYPE_EDGE_RISING>,
+			<GIC_SPI 220 IRQ_TYPE_EDGE_RISING>;
+	interrupt-names = "edma3_ccint", "emda3_mperr",
+			  "edma3_ccerrint";
+	dma-requests = <64>;
+	#dma-cells = <2>;
+
+	ti,tptcs = <&edma1_tptc0 7>, <&edma1_tptc1 0>;
+
+	/*
+	 * memcpy is disabled, can be enabled with:
+	 * ti,edma-memcpy-channels = <12 13 14 15>;
+	 * for example.
+	 */
+
+	power-domains = <&k2g_pds 0x4f>;
+};
+
+edma1_tptc0: tptc@027b0000 {
+	compatible = "ti,k2g-edma3-tptc", "ti,edma3-tptc";
+	reg =	<0x027b0000 0x400>;
+	power-domains = <&k2g_pds 0x4f>;
+};
+
+edma1_tptc1: tptc@027b8000 {
+	compatible = "ti, k2g-edma3-tptc", "ti,edma3-tptc";
+	reg =	<0x027b8000 0x400>;
+	power-domains = <&k2g_pds 0x4f>;
+};
+
+mmc0: mmc@23000000 {
+	compatible = "ti,k2g-hsmmc", "ti,omap4-hsmmc";
+	reg = <0x23000000 0x400>;
+	interrupts = <GIC_SPI 96 IRQ_TYPE_EDGE_RISING>;
+	dmas = <&edma1 24 0>, <&edma1 25 0>;
+	dma-names = "tx", "rx";
+	bus-width = <4>;
+	ti,needs-special-reset;
+	no-1-8-v;
+	max-frequency = <96000000>;
+	power-domains = <&k2g_pds 0xb>;
+	clocks = <&k2g_clks 0xb 1>, <&k2g_clks 0xb 2>;
+	clock-names = "fck", "mmchsdb_fck";
+	status = "disabled";
+};
+
 ------------------------------------------------------------------------------
 DEPRECATED binding, new DTS files must use the ti,edma3-tpcc/ti,edma3-tptc
 binding.
diff --git a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt
index 5aa5926029ee..039219df05c5 100644
--- a/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt
+++ b/Documentation/devicetree/bindings/gpu/arm,mali-midgard.txt
@@ -17,6 +17,7 @@ Required properties:
   * which must be preceded by one of the following vendor specifics:
     + "amlogic,meson-gxm-mali"
     + "rockchip,rk3288-mali"
+    + "rockchip,rk3399-mali"
 
 - reg : Physical base address of the device and length of the register area.
 
diff --git a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
index 11cc87aeb276..07bf0b9a5139 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
+++ b/Documentation/devicetree/bindings/interrupt-controller/mediatek,sysirq.txt
@@ -17,6 +17,7 @@ Required properties:
 	"mediatek,mt6582-sysirq", "mediatek,mt6577-sysirq": for MT6582
 	"mediatek,mt6580-sysirq", "mediatek,mt6577-sysirq": for MT6580
 	"mediatek,mt6577-sysirq": for MT6577
+	"mediatek,mt2712-sysirq", "mediatek,mt6577-sysirq": for MT2712
 	"mediatek,mt2701-sysirq", "mediatek,mt6577-sysirq": for MT2701
 - interrupt-controller : Identifies the node as an interrupt controller
 - #interrupt-cells : Use the same format as specified by GIC in arm,gic.txt.
diff --git a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
index 0e026c151c1c..3a4ac401e6f9 100644
--- a/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
+++ b/Documentation/devicetree/bindings/mmc/ti-omap-hsmmc.txt
@@ -1,33 +1,55 @@
-* TI Highspeed MMC host controller for OMAP
+* TI Highspeed MMC host controller for OMAP and 66AK2G family.
 
-The Highspeed MMC Host Controller on TI OMAP family
+The Highspeed MMC Host Controller on TI OMAP and 66AK2G family
 provides an interface for MMC, SD, and SDIO types of memory cards.
 
 This file documents differences between the core properties described
 by mmc.txt and the properties used by the omap_hsmmc driver.
 
 Required properties:
+--------------------
 - compatible:
  Should be "ti,omap2-hsmmc", for OMAP2 controllers
  Should be "ti,omap3-hsmmc", for OMAP3 controllers
  Should be "ti,omap3-pre-es3-hsmmc" for OMAP3 controllers pre ES3.0
  Should be "ti,omap4-hsmmc", for OMAP4 controllers
  Should be "ti,am33xx-hsmmc", for AM335x controllers
-- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1
+ Should be "ti,k2g-hsmmc", "ti,omap4-hsmmc" for 66AK2G controllers.
+
+SoC specific required properties:
+---------------------------------
+The following are mandatory properties for OMAPs, AM33xx and AM43xx SoCs only:
+- ti,hwmods: Must be "mmc<n>", n is controller instance starting 1.
+
+The following are mandatory properties for 66AK2G SoCs only:
+- power-domains:Should contain a phandle to a PM domain provider node
+		and an args specifier containing the MMC device id
+		value. This property is as per the binding,
+		Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
+- clocks:	Must contain an entry for each entry in clock-names. Should
+		be defined as per the he appropriate clock bindings consumer
+		usage in Documentation/devicetree/bindings/clock/ti,sci-clk.txt
+- clock-names:	Shall be "fck" for the functional clock,
+		and "mmchsdb_fck" for the debounce clock.
+
 
 Optional properties:
-ti,dual-volt: boolean, supports dual voltage cards
-<supply-name>-supply: phandle to the regulator device tree node
-"supply-name" examples are "vmmc", "vmmc_aux"(deprecated)/"vqmmc" etc
-ti,non-removable: non-removable slot (like eMMC)
-ti,needs-special-reset: Requires a special softreset sequence
-ti,needs-special-hs-handling: HSMMC IP needs special setting for handling High Speed
-dmas: List of DMA specifiers with the controller specific format
-as described in the generic DMA client binding. A tx and rx
-specifier is required.
-dma-names: List of DMA request names. These strings correspond
-1:1 with the DMA specifiers listed in dmas. The string naming is
-to be "rx" and "tx" for RX and TX DMA requests, respectively.
+--------------------
+- ti,dual-volt:		boolean, supports dual voltage cards
+- <supply-name>-supply:	phandle to the regulator device tree node
+			  "supply-name" examples are "vmmc",
+			  "vmmc_aux"(deprecated)/"vqmmc" etc
+- ti,non-removable:	non-removable slot (like eMMC)
+- ti,needs-special-reset:	Requires a special softreset sequence
+- ti,needs-special-hs-handling:	HSMMC IP needs special setting
+				  for handling High Speed
+- dmas:			List of DMA specifiers with the controller specific
+			format as described in the generic DMA client
+			binding. A tx and rx specifier is required.
+- dma-names:		List of DMA request names. These strings correspond
+			1:1 with the DMA specifiers listed in dmas.
+			The string naming is to be "rx" and "tx" for
+			RX and TX DMA requests, respectively.
 
 Examples:
 
diff --git a/Documentation/devicetree/bindings/net/can/c_can.txt b/Documentation/devicetree/bindings/net/can/c_can.txt
index 5a1d8b0c39e9..2d504256b0d8 100644
--- a/Documentation/devicetree/bindings/net/can/c_can.txt
+++ b/Documentation/devicetree/bindings/net/can/c_can.txt
@@ -11,9 +11,20 @@ Required properties:
 - interrupts		: property with a value describing the interrupt
 			  number
 
-Optional properties:
+The following are mandatory properties for DRA7x, AM33xx and AM43xx SoCs only:
 - ti,hwmods		: Must be "d_can<n>" or "c_can<n>", n being the
 			  instance number
+
+The following are mandatory properties for Keystone 2 66AK2G SoCs only:
+- power-domains		: Should contain a phandle to a PM domain provider node
+			  and an args specifier containing the DCAN device id
+			  value. This property is as per the binding,
+			  Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
+- clocks		: CAN functional clock phandle. This property is as per the
+			  binding,
+			  Documentation/devicetree/bindings/clock/ti,sci-clk.txt
+
+Optional properties:
 - syscon-raminit	: Handle to system control region that contains the
 			  RAMINIT register, register offset to the RAMINIT
 			  register and the CAN instance number (0 offset).
diff --git a/Documentation/devicetree/bindings/net/mediatek-net.txt b/Documentation/devicetree/bindings/net/mediatek-net.txt
index 1d1168b805cc..214eaa9a6683 100644
--- a/Documentation/devicetree/bindings/net/mediatek-net.txt
+++ b/Documentation/devicetree/bindings/net/mediatek-net.txt
@@ -20,8 +20,10 @@ Required properties:
         "ethif", "esw", "gp0", "gp1", "gp2", "sgmii_tx250m", "sgmii_rx250m",
 	"sgmii_cdr_ref", "sgmii_cdr_fb", "sgmii_ck", "eth2pll" : For MT7622 SoC
 - power-domains: phandle to the power domain that the ethernet is part of
-- resets: Should contain a phandle to the ethsys reset signal
-- reset-names: Should contain the reset signal name "eth"
+- resets: Should contain phandles to the ethsys reset signals
+- reset-names: Should contain the names of reset signal listed in the resets
+		property
+		These are "fe", "gmac" and "ppe"
 - mediatek,ethsys: phandle to the syscon node that handles the port setup
 - mediatek,sgmiisys: phandle to the syscon node that handles the SGMII setup
 	which is required for those SoCs equipped with SGMII such as MT7622 SoC.
diff --git a/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/Documentation/devicetree/bindings/pci/mvebu-pci.txt
index 127ae1f53e5a..6173af6885f8 100644
--- a/Documentation/devicetree/bindings/pci/mvebu-pci.txt
+++ b/Documentation/devicetree/bindings/pci/mvebu-pci.txt
@@ -276,7 +276,7 @@ pcie-controller {
 		clocks = <&gateclk 26>;
 	};
 
-	pcie@10,0 {
+	pcie@a,0 {
 		device_type = "pci";
 		assigned-addresses = <0x82005000 0 0x82000 0 0x2000>;
 		reg = <0x5000 0 0 0 0>;
diff --git a/Documentation/devicetree/bindings/power/renesas,apmu.txt b/Documentation/devicetree/bindings/power/renesas,apmu.txt
index 84404c9edff7..af21502e939c 100644
--- a/Documentation/devicetree/bindings/power/renesas,apmu.txt
+++ b/Documentation/devicetree/bindings/power/renesas,apmu.txt
@@ -1,12 +1,13 @@
 DT bindings for the Renesas Advanced Power Management Unit
 
-Renesas R-Car line of SoCs utilize one or more APMU hardware units
+Renesas R-Car and RZ/G1 SoCs utilize one or more APMU hardware units
 for CPU core power domain control including SMP boot and CPU Hotplug.
 
 Required properties:
 
 - compatible: Should be "renesas,<soctype>-apmu", "renesas,apmu" as fallback.
 	      Examples with soctypes are:
+		- "renesas,r8a7743-apmu" (RZ/G1M)
 		- "renesas,r8a7790-apmu" (R-Car H2)
 		- "renesas,r8a7791-apmu" (R-Car M2-W)
 		- "renesas,r8a7792-apmu" (R-Car V2H)
diff --git a/Documentation/devicetree/bindings/serial/mtk-uart.txt b/Documentation/devicetree/bindings/serial/mtk-uart.txt
index b6cf384597e1..f73abff3de43 100644
--- a/Documentation/devicetree/bindings/serial/mtk-uart.txt
+++ b/Documentation/devicetree/bindings/serial/mtk-uart.txt
@@ -3,6 +3,7 @@
 Required properties:
 - compatible should contain:
   * "mediatek,mt2701-uart" for MT2701 compatible UARTS
+  * "mediatek,mt2712-uart" for MT2712 compatible UARTS
   * "mediatek,mt6580-uart" for MT6580 compatible UARTS
   * "mediatek,mt6582-uart" for MT6582 compatible UARTS
   * "mediatek,mt6589-uart" for MT6589 compatible UARTS
diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt
index cc9f05d3cbc1..7dc5ce858a0e 100644
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.txt
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt
@@ -21,6 +21,7 @@ Required Properties:
    - "rockchip,rk3328-grf", "syscon": for rk3328
    - "rockchip,rk3368-grf", "syscon": for rk3368
    - "rockchip,rk3399-grf", "syscon": for rk3399
+   - "rockchip,rv1108-grf", "syscon": for rv1108
 - compatible: PMUGRF should be one of the following:
    - "rockchip,rk3368-pmugrf", "syscon": for rk3368
    - "rockchip,rk3399-pmugrf", "syscon": for rk3399
@@ -28,6 +29,8 @@ Required Properties:
    - "rockchip,rk3288-sgrf", "syscon": for rk3288
 - compatible: USB2PHYGRF should be one of the followings
    - "rockchip,rk3328-usb2phy-grf", "syscon": for rk3328
+- compatible: USBGRF should be one of the following
+   - "rockchip,rv1108-usbgrf", "syscon": for rv1108
 - reg: physical base address of the controller and length of memory mapped
   region.
 
diff --git a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
index c705db07d820..66e6265fb0aa 100644
--- a/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
+++ b/Documentation/devicetree/bindings/soc/ti/sci-pm-domain.txt
@@ -46,12 +46,13 @@ Required Properties:
 - power-domains: phandle pointing to the corresponding PM domain node
 		 and an ID representing the device.
 
-See dt-bindings/genpd/k2g.h for the list of valid identifiers for k2g.
+See http://processors.wiki.ti.com/index.php/TISCI#66AK2G02_Data for the list
+of valid identifiers for k2g.
 
 Example (K2G):
 --------------------
 	uart0: serial@02530c00 {
 		compatible = "ns16550a";
 		...
-		power-domains = <&k2g_pds K2G_DEV_UART0>;
+		power-domains = <&k2g_pds 0x002c>;
 	};
diff --git a/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt b/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt
new file mode 100644
index 000000000000..712d05e3e15e
--- /dev/null
+++ b/Documentation/devicetree/bindings/sram/renesas,smp-sram.txt
@@ -0,0 +1,27 @@
+* Renesas SMP SRAM
+
+Renesas R-Car Gen2 and RZ/G1 SoCs need a small piece of SRAM for the jump stub
+for secondary CPU bringup and CPU hotplug.
+This memory is reserved by adding a child node to a "mmio-sram" node, cfr.
+Documentation/devicetree/bindings/sram/sram.txt.
+
+Required child node properties:
+  - compatible: Must be "renesas,smp-sram",
+  - reg: Address and length of the reserved SRAM.
+    The full physical (bus) address must be aligned to a 256 KiB boundary.
+
+
+Example:
+
+	icram1:	sram@e63c0000 {
+		compatible = "mmio-sram";
+		reg = <0 0xe63c0000 0 0x1000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0 0xe63c0000 0x1000>;
+
+		smp-sram@0 {
+			compatible = "renesas,smp-sram";
+			reg = <0 0x10>;
+		};
+	};
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 5a79aeb620b3..69183f0fbc78 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -48,6 +48,7 @@ avic	Shanghai AVIC Optoelectronics Co., Ltd.
 axentia	Axentia Technologies AB
 axis	Axis Communications AB
 bananapi BIPAI KEJI LIMITED
+bhf	Beckhoff Automation GmbH & Co. KG
 boe	BOE Technology Group Co., Ltd.
 bosch	Bosch Sensortec GmbH
 boundary	Boundary Devices Inc.
diff --git a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
index 6a00939a059a..20ada673ab0c 100644
--- a/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
+++ b/Documentation/devicetree/bindings/watchdog/mtk-wdt.txt
@@ -3,9 +3,9 @@ Mediatek SoCs Watchdog timer
 Required properties:
 
 - compatible should contain:
-	* "mediatek,mt2701-wdt" for MT2701 compatible watchdog timers
-	* "mediatek,mt6589-wdt" for all compatible watchdog timers (MT2701,
-		MT6589)
+	"mediatek,mt2701-wdt", "mediatek,mt6589-wdt": for MT2701
+	"mediatek,mt6589-wdt": for MT6589
+	"mediatek,mt6797-wdt", "mediatek,mt6589-wdt": for MT6797
 
 - reg : Specifies base physical address and size of the registers.