1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
|
/* SPDX-License-Identifier: GPL-2.0-only */
#ifndef _LINUX_GPIO_REGMAP_H
#define _LINUX_GPIO_REGMAP_H
struct device;
struct gpio_regmap;
struct irq_domain;
struct regmap;
#define GPIO_REGMAP_ADDR_ZERO ((unsigned long)(-1))
#define GPIO_REGMAP_ADDR(addr) ((addr) ? : GPIO_REGMAP_ADDR_ZERO)
/**
* struct gpio_regmap_config - Description of a generic regmap gpio_chip.
* @parent: The parent device
* @regmap: The regmap used to access the registers
* given, the name of the device is used
* @label: (Optional) Descriptive name for GPIO controller.
* If not given, the name of the device is used.
* @ngpio: Number of GPIOs
* @names: (Optional) Array of names for gpios
* @reg_dat_base: (Optional) (in) register base address
* @reg_set_base: (Optional) set register base address
* @reg_clr_base: (Optional) clear register base address
* @reg_dir_in_base: (Optional) in setting register base address
* @reg_dir_out_base: (Optional) out setting register base address
* @reg_stride: (Optional) May be set if the registers (of the
* same type, dat, set, etc) are not consecutive.
* @ngpio_per_reg: Number of GPIOs per register
* @irq_domain: (Optional) IRQ domain if the controller is
* interrupt-capable
* @reg_mask_xlate: (Optional) Translates base address and GPIO
* offset to a register/bitmask pair. If not
* given the default gpio_regmap_simple_xlate()
* is used.
*
* The ->reg_mask_xlate translates a given base address and GPIO offset to
* register and mask pair. The base address is one of the given register
* base addresses in this structure.
*
* Although all register base addresses are marked as optional, there are
* several rules:
* 1. if you only have @reg_dat_base set, then it is input-only
* 2. if you only have @reg_set_base set, then it is output-only
* 3. if you have either @reg_dir_in_base or @reg_dir_out_base set, then
* you have to set both @reg_dat_base and @reg_set_base
* 4. if you have @reg_set_base set, you may also set @reg_clr_base to have
* two different registers for setting and clearing the output. This is
* also valid for the output-only case.
* 5. @reg_dir_in_base and @reg_dir_out_base are exclusive; is there really
* hardware which has redundant registers?
*
* Note: All base addresses may have the special value %GPIO_REGMAP_ADDR_ZERO
* which forces the address to the value 0.
*/
struct gpio_regmap_config {
struct device *parent;
struct regmap *regmap;
const char *label;
int ngpio;
const char *const *names;
unsigned int reg_dat_base;
unsigned int reg_set_base;
unsigned int reg_clr_base;
unsigned int reg_dir_in_base;
unsigned int reg_dir_out_base;
int reg_stride;
int ngpio_per_reg;
struct irq_domain *irq_domain;
int (*reg_mask_xlate)(struct gpio_regmap *gpio, unsigned int base,
unsigned int offset, unsigned int *reg,
unsigned int *mask);
};
struct gpio_regmap *gpio_regmap_register(const struct gpio_regmap_config *config);
void gpio_regmap_unregister(struct gpio_regmap *gpio);
struct gpio_regmap *devm_gpio_regmap_register(struct device *dev,
const struct gpio_regmap_config *config);
void gpio_regmap_set_drvdata(struct gpio_regmap *gpio, void *data);
void *gpio_regmap_get_drvdata(struct gpio_regmap *gpio);
#endif /* _LINUX_GPIO_REGMAP_H */
|
