1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
|
GPIO Sysfs Interface for Userspace
==================================
.. warning::
This API is obsoleted by the chardev.rst and the ABI documentation has
been moved to Documentation/ABI/obsolete/sysfs-gpio.
New developments should use the chardev.rst, and existing developments are
encouraged to migrate as soon as possible, as this API will be removed
in the future.
This interface will continue to be maintained for the migration period,
but new features will only be added to the new API.
The obsolete sysfs ABI
----------------------
Platforms which use the "gpiolib" implementors framework may choose to
configure a sysfs user interface to GPIOs. This is different from the
debugfs interface, since it provides control over GPIO direction and
value instead of just showing a gpio state summary. Plus, it could be
present on production systems without debugging support.
Given appropriate hardware documentation for the system, userspace could
know for example that GPIO #23 controls the write protect line used to
protect boot loader segments in flash memory. System upgrade procedures
may need to temporarily remove that protection, first importing a GPIO,
then changing its output state, then updating the code before re-enabling
the write protection. In normal use, GPIO #23 would never be touched,
and the kernel would have no need to know about it.
Again depending on appropriate hardware documentation, on some systems
userspace GPIO can be used to determine system configuration data that
standard kernels won't know about. And for some tasks, simple userspace
GPIO drivers could be all that the system really needs.
.. note::
Do NOT abuse sysfs to control hardware that has proper kernel drivers.
Please read Documentation/driver-api/gpio/drivers-on-gpio.rst
to avoid reinventing kernel wheels in userspace.
I MEAN IT. REALLY.
Paths in Sysfs
--------------
There are three kinds of entries in /sys/class/gpio:
- Control interfaces used to get userspace control over GPIOs;
- GPIOs themselves; and
- GPIO controllers ("gpio_chip" instances).
That's in addition to standard files including the "device" symlink.
The control interfaces are write-only:
/sys/class/gpio/
"export" ...
Userspace may ask the kernel to export control of
a GPIO to userspace by writing its number to this file.
Example: "echo 19 > export" will create a "gpio19" node
for GPIO #19, if that's not requested by kernel code.
"unexport" ...
Reverses the effect of exporting to userspace.
Example: "echo 19 > unexport" will remove a "gpio19"
node exported using the "export" file.
GPIO signals have paths like /sys/class/gpio/gpio42/ (for GPIO #42)
and have the following read/write attributes:
/sys/class/gpio/gpioN/
"direction" ...
reads as either "in" or "out". This value may
normally be written. Writing as "out" defaults to
initializing the value as low. To ensure glitch free
operation, values "low" and "high" may be written to
configure the GPIO as an output with that initial value.
Note that this attribute *will not exist* if the kernel
doesn't support changing the direction of a GPIO, or
it was exported by kernel code that didn't explicitly
allow userspace to reconfigure this GPIO's direction.
"value" ...
reads as either 0 (inactive) or 1 (active). If the GPIO
is configured as an output, this value may be written;
any nonzero value is treated as active.
If the pin can be configured as interrupt-generating interrupt
and if it has been configured to generate interrupts (see the
description of "edge"), you can poll(2) on that file and
poll(2) will return whenever the interrupt was triggered. If
you use poll(2), set the events POLLPRI and POLLERR. If you
use select(2), set the file descriptor in exceptfds. After
poll(2) returns, use pread(2) to read the value at offset
zero. Alternatively, either lseek(2) to the beginning of the
sysfs file and read the new value or close the file and
re-open it to read the value.
"edge" ...
reads as either "none", "rising", "falling", or
"both". Write these strings to select the signal edge(s)
that will make poll(2) on the "value" file return.
This file exists only if the pin can be configured as an
interrupt generating input pin.
"active_low" ...
reads as either 0 (false) or 1 (true). Write
any nonzero value to invert the value attribute both
for reading and writing. Existing and subsequent
poll(2) support configuration via the edge attribute
for "rising" and "falling" edges will follow this
setting.
GPIO controllers have paths like /sys/class/gpio/gpiochip42/ (for the
controller implementing GPIOs starting at #42) and have the following
read-only attributes:
/sys/class/gpio/gpiochipN/
"base" ...
same as N, the first GPIO managed by this chip
"label" ...
provided for diagnostics (not always unique)
"ngpio" ...
how many GPIOs this manages (N to N + ngpio - 1)
Board documentation should in most cases cover what GPIOs are used for
what purposes. However, those numbers are not always stable; GPIOs on
a daughtercard might be different depending on the base board being used,
or other cards in the stack. In such cases, you may need to use the
gpiochip nodes (possibly in conjunction with schematics) to determine
the correct GPIO number to use for a given signal.
Exporting from Kernel code
--------------------------
Kernel code can explicitly manage exports of GPIOs which have already been
requested using gpio_request()::
/* export the GPIO to userspace */
int gpiod_export(struct gpio_desc *desc, bool direction_may_change);
/* reverse gpiod_export() */
void gpiod_unexport(struct gpio_desc *desc);
/* create a sysfs link to an exported GPIO node */
int gpiod_export_link(struct device *dev, const char *name,
struct gpio_desc *desc);
After a kernel driver requests a GPIO, it may only be made available in
the sysfs interface by gpiod_export(). The driver can control whether the
signal direction may change. This helps drivers prevent userspace code
from accidentally clobbering important system state.
This explicit exporting can help with debugging (by making some kinds
of experiments easier), or can provide an always-there interface that's
suitable for documenting as part of a board support package.
After the GPIO has been exported, gpiod_export_link() allows creating
symlinks from elsewhere in sysfs to the GPIO sysfs node. Drivers can
use this to provide the interface under their own device in sysfs with
a descriptive name.
|
