1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
|
zram: Compressed RAM based block devices
----------------------------------------
* Introduction
The zram module creates RAM based block devices named /dev/zram<id>
(<id> = 0, 1, ...). Pages written to these disks are compressed and stored
in memory itself. These disks allow very fast I/O and compression provides
good amounts of memory savings. Some of the usecases include /tmp storage,
use as swap disks, various caches under /var and maybe many more :)
Statistics for individual zram devices are exported through sysfs nodes at
/sys/block/zram<id>/
* Usage
Following shows a typical sequence of steps for using zram.
1) Load Module:
modprobe zram num_devices=4
This creates 4 devices: /dev/zram{0,1,2,3}
(num_devices parameter is optional. Default: 1)
2) Set max number of compression streams
Compression backend may use up to max_comp_streams compression streams,
thus allowing up to max_comp_streams concurrent compression operations.
By default, compression backend uses single compression stream.
Examples:
#show max compression streams number
cat /sys/block/zram0/max_comp_streams
#set max compression streams number to 3
echo 3 > /sys/block/zram0/max_comp_streams
Note:
In order to enable compression backend's multi stream support max_comp_streams
must be initially set to desired concurrency level before ZRAM device
initialisation. Once the device initialised as a single stream compression
backend (max_comp_streams equals to 1), you will see error if you try to change
the value of max_comp_streams because single stream compression backend
implemented as a special case by lock overhead issue and does not support
dynamic max_comp_streams. Only multi stream backend supports dynamic
max_comp_streams adjustment.
3) Select compression algorithm
Using comp_algorithm device attribute one can see available and
currently selected (shown in square brackets) compression algortithms,
change selected compression algorithm (once the device is initialised
there is no way to change compression algorithm).
Examples:
#show supported compression algorithms
cat /sys/block/zram0/comp_algorithm
lzo [lz4]
#select lzo compression algorithm
echo lzo > /sys/block/zram0/comp_algorithm
4) Set Disksize
Set disk size by writing the value to sysfs node 'disksize'.
The value can be either in bytes or you can use mem suffixes.
Examples:
# Initialize /dev/zram0 with 50MB disksize
echo $((50*1024*1024)) > /sys/block/zram0/disksize
# Using mem suffixes
echo 256K > /sys/block/zram0/disksize
echo 512M > /sys/block/zram0/disksize
echo 1G > /sys/block/zram0/disksize
Note:
There is little point creating a zram of greater than twice the size of memory
since we expect a 2:1 compression ratio. Note that zram uses about 0.1% of the
size of the disk when not in use so a huge zram is wasteful.
5) Set memory limit: Optional
Set memory limit by writing the value to sysfs node 'mem_limit'.
The value can be either in bytes or you can use mem suffixes.
In addition, you could change the value in runtime.
Examples:
# limit /dev/zram0 with 50MB memory
echo $((50*1024*1024)) > /sys/block/zram0/mem_limit
# Using mem suffixes
echo 256K > /sys/block/zram0/mem_limit
echo 512M > /sys/block/zram0/mem_limit
echo 1G > /sys/block/zram0/mem_limit
# To disable memory limit
echo 0 > /sys/block/zram0/mem_limit
6) Activate:
mkswap /dev/zram0
swapon /dev/zram0
mkfs.ext4 /dev/zram1
mount /dev/zram1 /tmp
7) Stats:
Per-device statistics are exported as various nodes under /sys/block/zram<id>/
A brief description of exported device attritbutes. For more details please
read Documentation/ABI/testing/sysfs-block-zram.
Name access description
---- ------ -----------
disksize RW show and set the device's disk size
initstate RO shows the initialization state of the device
reset WO trigger device reset
num_reads RO the number of reads
failed_reads RO the number of failed reads
num_write RO the number of writes
failed_writes RO the number of failed writes
invalid_io RO the number of non-page-size-aligned I/O requests
max_comp_streams RW the number of possible concurrent compress operations
comp_algorithm RW show and change the compression algorithm
notify_free RO the number of notifications to free pages (either
slot free notifications or REQ_DISCARD requests)
zero_pages RO the number of zero filled pages written to this disk
orig_data_size RO uncompressed size of data stored in this disk
compr_data_size RO compressed size of data stored in this disk
mem_used_total RO the amount of memory allocated for this disk
mem_used_max RW the maximum amount memory zram have consumed to
store compressed data
mem_limit RW the maximum amount of memory ZRAM can use to store
the compressed data
num_migrated RO the number of objects migrated migrated by compaction
File /sys/block/zram<id>/stat
Represents block layer statistics. Read Documentation/block/stat.txt for
details.
File /sys/block/zram<id>/io_stat
The stat file represents device's I/O statistics not accounted by block
layer and, thus, not available in zram<id>/stat file. It consists of a
single line of text and contains the following stats separated by
whitespace:
failed_reads
failed_writes
invalid_io
notify_free
8) Deactivate:
swapoff /dev/zram0
umount /dev/zram1
9) Reset:
Write any positive value to 'reset' sysfs node
echo 1 > /sys/block/zram0/reset
echo 1 > /sys/block/zram1/reset
This frees all the memory allocated for the given device and
resets the disksize to zero. You must set the disksize again
before reusing the device.
Nitin Gupta
ngupta@vflare.org
|
