| Age | Commit message (Collapse) | Author |
|---|
|
This will allow the low level driver to take different actions for
different flows.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20240618192529.739036208b6e.Ie18a2fe8e02bf2717549d39420b350cfdaf3d317@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When wpa_supplicant is initiated by users and not by NetworkManager,
the CQM configuration might not be set. Without this setting, ICs
with connection quality monitor handled by firmware won't detect
connection loss. To fix this we prepare a default setting upon
associated at first, then update again if any is given later.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://msgid.link/20240401033019.9664-1-pkshih@realtek.com
|
|
There are still surprisingly many non-chanctx drivers, but in
mac80211 that code is a bit awkward. Simplify this by having
those drivers assign 'emulated' ops, so that the mac80211 code
can be more unified between non-chanctx/chanctx drivers. This
cuts the number of places caring about it by about 15, which
are scattered across - now they're fewer and no longer in the
channel context handling.
Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The broadcast packets will be filtered in the FIF_ALLMULTI flag in
the original code, which causes beacon packets to be filtered out
and disconnection. Therefore, we fix it.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231103020851.102238-1-pkshih@realtek.com
|
|
Without this patch, firmware only track beacons for port 0 and since
we will always start AP on port 0, this results in misbehavior of
power saving mode on other ports after AP stops.
The "default port" H2C command is used to notify which port should
firmware track. Update the correct settings to firmware so power
saving mode can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-7-pkshih@realtek.com
|
|
Broadcast and multicast packets in high queue should be transmitted
all at once during DTIM. But without proper settings, hardware fails
to recognize that there are multiple packets and fetches only one.
Fix this by signaling hardware with more data bit set when there are
packets in the high queue.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-3-pkshih@realtek.com
|
|
In the wpa_supplicant rekey flow, it sends an EAPOL packet 4/4 through
nl80211_tx_control_port() and triggers wake_tx_queue() in the driver.
Then, it sends nl80211_new_key() to configure a new key in mac80211.
However, in wake_tx_queue(), a workqueue is used to process the tx packet,
which might cause the driver to process the EAPOL packet later than
nl80211_new_key(). As a result, the EAPOL 4/4 packet is dropped by mac80211
due to the rekey configuration being finished. The EAPOL packets belongs to
VO packets that need high priority. Therefore, we process VO packets
directly without workqueue to ensure that packets can process immediately.
VO is normally used by voice application that is low traffic load and low
latency, that doesn't affect user experience.
We test iperf with VO packets(iperf3 -P4 -u -b 10000M -S 0xdf)
before after
TX throughput 162M 162M
ping RTT 3.8ms 3.7ms
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616031713.16769-1-pkshih@realtek.com
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
net/sched/sch_taprio.c
d636fc5dd692 ("net: sched: add rcu annotations around qdisc->qdisc_sleeping")
dced11ef84fb ("net/sched: taprio: don't overwrite "sch" variable in taprio_dump_class_stats()")
net/ipv4/sysctl_net_ipv4.c
e209fee4118f ("net/ipv4: ping_group_range: allow GID from 2147483648 to 4294967294")
ccce324dabfe ("tcp: make the first N SYN RTO backoffs linear")
https://lore.kernel.org/all/20230605100816.08d41a7b@canb.auug.org.au/
No adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This driver relies on IEEE80211_CONF_PS of hw->conf.flags to turn off PS or
turn on dynamic PS controlled by driver and firmware. Though this would be
incorrect, it did work before because the flag is always recalculated until
the commit 28977e790b5d ("wifi: mac80211: skip powersave recalc if driver SUPPORTS_DYNAMIC_PS")
is introduced by kernel 5.20 to skip to recalculate IEEE80211_CONF_PS
of hw->conf.flags if driver sets SUPPORTS_DYNAMIC_PS.
Correct this by doing recalculation while BSS_CHANGED_PS is changed and
interface is added or removed. It is allowed to enter PS only if single
one station vif is working. Without this fix, driver doesn't enter PS
anymore that causes higher power consumption.
Fixes: bcde60e599fb ("rtw88: remove misleading module parameter rtw_fw_support_lps")
Cc: stable@vger.kernel.org # 6.1+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230527082939.11206-2-pkshih@realtek.com
|
|
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
6ead9c98cafc ("net: fec: remove the xdp_return_frame when lack of tx BDs")
144470c88c5d ("net: fec: using the standard return codes when xdp xmit errors")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ieee80211_ops::sta_rc_update must be atomic, because
ieee80211_chan_bw_change() holds rcu_read lock while calling
drv_sta_rc_update(), so create a work to do original things.
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 4621 at kernel/rcu/tree_plugin.h:318
rcu_note_context_switch+0x571/0x5d0
CPU: 0 PID: 4621 Comm: kworker/u16:2 Tainted: G W OE
Workqueue: phy3 ieee80211_chswitch_work [mac80211]
RIP: 0010:rcu_note_context_switch+0x571/0x5d0
Call Trace:
<TASK>
__schedule+0xb0/0x1460
? __mod_timer+0x116/0x360
schedule+0x5a/0xc0
schedule_timeout+0x87/0x150
? trace_raw_output_tick_stop+0x60/0x60
wait_for_completion_timeout+0x7b/0x140
usb_start_wait_urb+0x82/0x160 [usbcore
usb_control_msg+0xe3/0x140 [usbcore
rtw_usb_read+0x88/0xe0 [rtw_usb
rtw_usb_read8+0xf/0x10 [rtw_usb
rtw_fw_send_h2c_command+0xa0/0x170 [rtw_core
rtw_fw_send_ra_info+0xc9/0xf0 [rtw_core
drv_sta_rc_update+0x7c/0x160 [mac80211
ieee80211_chan_bw_change+0xfb/0x110 [mac80211
ieee80211_change_chanctx+0x38/0x130 [mac80211
ieee80211_vif_use_reserved_switch+0x34e/0x900 [mac80211
ieee80211_link_use_reserved_context+0x88/0xe0 [mac80211
ieee80211_chswitch_work+0x95/0x170 [mac80211
process_one_work+0x201/0x410
worker_thread+0x4a/0x3b0
? process_one_work+0x410/0x410
kthread+0xe1/0x110
? kthread_complete_and_exit+0x20/0x20
ret_from_fork+0x1f/0x30
</TASK>
Cc: stable@vger.kernel.org
Fixes: c1edc86472fc ("rtw88: add ieee80211:sta_rc_update ops")
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/linux-wireless/f1e31e8e-f84e-3791-50fb-663a83c5c6e9@lwfinger.net/T/#t
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230508085429.46653-1-pkshih@realtek.com
|
|
Call mutex_unlock(&rtwdev->mutex); before returning on this error path.
Fixes: f0e741e4ddbc ("wifi: rtw88: add bitmap for dynamic port settings")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/ddd10a74-5982-4f65-8c59-c1cca558d239@kili.mountain
|
|
This patch allows vifs sharing same hardware with the AP mode vif to
do scan, do note that this could lead to packet loss or disconnection
of the AP's clients. Since we don't have chanctx, update scan info
upon set channel so bandwidth changes won't go unnoticed and get
misconfigured after scan. Download beacon just before scan starts to
allow hardware to get proper content to do beaconing. Last, beacons
should only be transmitted in AP's operating channel. Turn related
beacon functions off while we're in other channels so the receiving
stations won't get confused.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121323.18008-1-pkshih@realtek.com
|
|
Only abort scan with current scanning VIF. If we have more than one
interface, we could call rtw_hw_scan_abort() with the wrong VIF as
input. This avoids potential null pointer being accessed when actually
the other VIF is scanning.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121312.17954-1-pkshih@realtek.com
|
|
Only gather reserved pages from AP interface after it has started. Or
else ieee80211_beacon_get_*() returns NULL and causes other VIFs'
reserved pages fail to download. Update location of current reserved page
after beacon renews so offsets changed by beacon can be recognized.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121300.17900-1-pkshih@realtek.com
|
|
Firmware can't support PS mode during AP mode, so disallow this case.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-5-pkshih@realtek.com
|
|
Switch port settings if AP mode does not start on port 0 because of
hardware limitation. For some ICs, beacons on ports other than zero
could misbehave and do not issue properly, to fix this we change AP
VIFs to port zero when multiple interfaces is active.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-3-pkshih@realtek.com
|
|
In order to support multiple interfaces, multiple port settings will
be required. Current code always uses port 0 and should be changed.
Declare a bitmap with size equal to hardware port number to record
the current usage.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230414121135.17828-2-pkshih@realtek.com
|
|
USB and (upcoming) SDIO support may sleep in the read/write handlers.
Use non-atomic rtw_iterate_stas() in rtw_ra_mask_info_update() because
the iterator function rtw_ra_mask_info_update_iter() needs to read and
write registers from within rtw_update_sta_info(). Using the non-atomic
iterator ensures that we can sleep during USB and SDIO register reads
and writes. This fixes "scheduling while atomic" or "Voluntary context
switch within RCU read-side critical section!" warnings as seen by SDIO
card users (but it also affects USB cards).
Fixes: 78d5bf925f30 ("wifi: rtw88: iterate over vif/sta list non-atomically")
Suggested-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230108211324.442823-4-martin.blumenstingl@googlemail.com
|
|
rtw_fw_beacon_filter_config() is called once with rtwdev->mutex held
and once without the mutex held. Call it consistently with rtwdev->mutex
held.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221202081224.2779981-3-s.hauer@pengutronix.de
|
|
Mac80211 core may ask driver to change to idle mode during HW scan,
then H2C command for HW scan will send failed since chip is in idle
mode. Therefore, We check the SCANNING flag before entering IPS to
prevent this behavior.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809084107.38137-8-pkshih@realtek.com
|
|
During HW scan, the channel related feilds in hal struct changed partially.
If setting Tx power will get WARNING:rtw_get_tx_power_params() due to some
of fields in hal struct mismatch. Therefore, we fix to change all required
fields in hal struct when channel switch during HW scan.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809084107.38137-5-pkshih@realtek.com
|
|
Applying SAR will access hal data, it should hold rtwdev::mutex
to avoid hal data changed during setting flow.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220809084107.38137-2-pkshih@realtek.com
|
|
Since chip_info has became const table, we must access them via const
pointer to avoid invalid writing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065232.28510-1-pkshih@realtek.com
|
|
The original timing that store OP channel info is after associated.
However, HW scan might happen before associated without backing to
OP channel, that will cause authentication or association fail.
Therefore, we modify the timing of storing OP channel info.
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220727065003.28340-4-pkshih@realtek.com
|
|
When calling start/stop_ap(), mac80211 already has a protected
link_conf pointer. Pass it to the driver, so it shouldn't
handle RCU protection.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Take the link into account in the QoS settings (EDCA parameters)
APIs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In start_ap and stop_ap mac80211 callbacks pass the link_id
to the drivers.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The set_tim is supposed to be atomic, but we should download beacon
context to firmware with a mutex lock. To avoid warning, do the thing in
another work.
BUG: scheduling while atomic: swapper/1/0/0x00000700
Modules linked in:
CPU: 1 PID: 0 Comm: swapper/1 Tainted: G W 5.18.0-rc7-00703-g33b5ee09a0c1 #4
Hardware name: Pine64 RK3566 Quartz64-A Board (DT)
Call trace:
dump_backtrace.part.0+0xc4/0xd0
show_stack+0x14/0x60
dump_stack_lvl+0x60/0x78
dump_stack+0x14/0x2c
__schedule_bug+0x5c/0x70
__schedule+0x5c4/0x630
schedule+0x44/0xb0
schedule_preempt_disabled+0xc/0x14
__mutex_lock.constprop.0+0x538/0x56c
__mutex_lock_slowpath+0x10/0x20
mutex_lock+0x54/0x60
rtw_ops_set_tim+0x20/0x40
__sta_info_recalc_tim+0x150/0x250
sta_info_recalc_tim+0x10/0x20
invoke_tx_handlers_early+0x4e4/0x5c0
ieee80211_tx+0x78/0x110
ieee80211_xmit+0x94/0xc0
__ieee80211_subif_start_xmit+0x818/0xd20
ieee80211_subif_start_xmit+0x44/0x2d0
dev_hard_start_xmit+0xd0/0x150
__dev_queue_xmit+0x250/0xb30
dev_queue_xmit+0x10/0x20
br_dev_queue_push_xmit+0x94/0x174
br_forward_finish+0x90/0xa0
__br_forward+0xc0/0x13c
br_forward+0x108/0x134
br_dev_xmit+0x1cc/0x3a4
dev_hard_start_xmit+0xd0/0x150
__dev_queue_xmit+0x250/0xb30
dev_queue_xmit+0x10/0x20
arp_xmit+0x6c/0x7c
arp_send_dst+0x8c/0xc0
arp_solicit+0xd4/0x1e0
neigh_probe+0x58/0xa0
neigh_timer_handler+0x27c/0x380
call_timer_fn.constprop.0+0x20/0x80
__run_timers.part.0+0x230/0x280
run_timer_softirq+0x38/0x70
_stext+0x104/0x278
__irq_exit_rcu+0xa4/0xdc
irq_exit_rcu+0xc/0x14
el1_interrupt+0x34/0x50
el1h_64_irq_handler+0x14/0x20
el1h_64_irq+0x64/0x68
arch_cpu_idle+0x14/0x20
do_idle+0x208/0x290
cpu_startup_entry+0x20/0x30
secondary_start_kernel+0x130/0x144
__secondary_switched+0x54/0x58
Fixes: f2217968ffda ("rtw88: Add update beacon flow for AP mode")
Reported-by: Ondřej Jirman <megi@xff.cz>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Ondřej Jirman <megi@xff.cz>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220526051251.281905-1-pkshih@realtek.com
|
|
Calling calibration to yield expected PHY performance. We do this in STA
mode, so do this in AP mode as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-6-pkshih@realtek.com
|
|
To support stations in power saving mode, AP should notify stations
that there are frames buffered at the AP via TIM during beacons.
Driver used to transmit identical beacons that were downloaded to
hardware during the initiation phase. This beacon will become
obsolete over time.
If the beacon does not contain sufficient information, station would
not be able to percept that there is data to receive. Hence it won't
wake up and start the PS-poll procedure, this could lead to timeout
and/or lost data segments. In order to resolve this issue, driver will
now download beacon to hardware whenever the content is updated.
Enable hardware to update dtim_count for more efficiency, this reduces
the overhead of downloading beacon at every beacon interval since most
of the time only the dtim_count needs to be updated.
Change queue mapping for broadcast/multicast frames to high queue, so
these frames can be prioritized and sent when dtim_count is zero.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-4-pkshih@realtek.com
|
|
Adding this allows us to get notification when bitrate configuration
of the station changes. Update according parameters to firmware so
the rate control algorithm can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220407095858.46807-2-pkshih@realtek.com
|
|
Larry reported funny log entries [1] when he used rtl8821ce. These
messages are not harmless, but not useful for users, so change them to
rtw_dbg() level. By the way, I review all rtw_info() and change others
to rtw_warn().
[1] https://lore.kernel.org/linux-wireless/c356d5ae-a7b3-3065-1121-64c446e70333@lwfinger.net/
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220218035527.9835-1-pkshih@realtek.com
|
|
Upon hw scan completion, idle mode is not re-entered. This might
increase power consumption under no link mode. Fix this by adding the
re-enter flow. We need another work for this since enter_ips waits
for c2h_work to finish, which might lead to deadlock if caller is in
the same work.
Fixes: 10d162b2ed39 ("rtw88: 8822c: add ieee80211_ops::hw_scan")
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220121070813.9656-3-pkshih@realtek.com
|
|
Register cfg80211_sar_capa with type NL80211_SAR_TYPE_POWER and four
frequency ranges for configurations in unit of 0.25 dBm. And handle
callback set_sar_specs.
Originally, TX power has three main parameters, i.e. power base,
power by rate, and power limit. The formula can be simply considered
as TX power = power base + min(power by rate, power limit). With the
support of SAR which can be treated as another power limit, there is
one more parameter for TX power. And the formula will evolve into
TX power = power base + min(power by rate, power limit, power sar).
Besides, debugfs tx_pwr_tbl is also refined to show SAR information.
The following is an example for the difference.
Before supporting SAR,
-----------------------------------
...
path rate pwr base (byr lmt ) rem
A CCK_1M 66(0x42) 78 -12 ( 12 -12) 0
A CCK_2M 66(0x42) 78 -12 ( 8 -12) 0
...
-----------------------------------
After supporting SAR and making some configurations,
-----------------------------------
...
path rate pwr base (byr lmt sar ) rem
A CCK_1M 62(0x3e) 78 -16 ( 12 -12 -16) 0
A CCK_2M 62(0x3e) 78 -16 ( 8 -12 -16) 0
...
-----------------------------------
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211220093656.65312-1-pkshih@realtek.com
|
|
Declare this function allows us to use customized scanning policy.
By doing so we can be more time efficient on each scan. In order to
make existing coex mechanism work as usual, firmware notifies driver
on each channel switch event, then decide antenna ownership based on
the current channel/band. Do note that this new mechanism affects
throughput more than the sw_scan we used to have, but the overall
average throughput is not affected since each scan take less time.
Since the firmware size is limited, we only support probe requests
with custom IEs length under 128 bytes for now, if any user space
tools requires more than that, we'll introduce related changes
afterwards. For backward compatibility, we fallback to sw_scan when
using older firmware that does not support this feature.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20211221085010.39421-1-pkshih@realtek.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes berg says:
====================
Lots of changes:
* aggregation handling improvements for some drivers
* hidden AP discovery on 6 GHz and other HE 6 GHz
improvements
* minstrel improvements for no-ack frames
* deferred rate control for TXQs to improve reaction
times
* virtual time-based airtime scheduler
* along with various little cleanups/fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have mgd_prepare_tx(), but sometimes drivers may want/need
to take action when the exchange finishes, whether successfully
or not.
Add a notification to the driver on completion, i.e. call the
new method mgd_complete_tx().
To unify the two scenarios, and to add more information, make
both of them take a struct that has the duration (prepare only),
subtype (both) and success (complete only).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210618133832.5d94e78f6230.I6dc979606b6f28701b740d7aab725f7853a5a155@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It is found that driver scan could be affected by dynamic mechanism
of firmware, so we notify firmware to stop it in the scan period.
Another, firmware will detect the background noise and report to
driver for further use.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210514075517.14216-3-pkshih@realtek.com
|
|
add api to check if a certain feature is supported.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210514075517.14216-2-pkshih@realtek.com
|
|
Adding this supports beacon filter and CQM.
Let firmware perform connection quality monitor and beacon processing.
This make host CPU wakeup less under power save mode.
To make mechanisms work as usual, fw will notify driver events such as
signal change and beacon loss.
This feature needs firmware 9.9.8 or newer to support it, and driver is
compatible with older firmware.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210426013252.5665-1-pkshih@realtek.com
|
|
Though mac queue flushing has been supported, sometimes data may be waiting
on interface from host to chip. If it occurs, there may still be data that
flows into mac just after we do flush. To avoid that, we add the hci part
of flushing.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210319054218.3319-2-pkshih@realtek.com
|
|
Replace tasklet so we can do tx scheduling in parallel. Since throughput
is delay-sensitive in most cases, we allocate a dedicated, high priority
wq for our needs.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210209070755.23019-5-pkshih@realtek.com
|
|
Add considering for different WLAN beacon interval in coexistence
mechanism.
Because the WLAN beacon period may be not 100 ms, so it's necessary
to consider any beacon period and set timer according to the interval.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201112031430.4846-2-pkshih@realtek.com
|
|
This patch checks the supported lps deep mode from firmware feature,
and allows different firmware have different deep power mode.
Original module parameter rtw_fw_lps_deep_mode is replaced with
rtw_disable_lps_deep_mode for user to disable lps deep mode.
Signed-off-by: Chin-Yen Lee <timlee@realtek.com>
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201030084826.9034-5-tehuang@realtek.com
|
|
This handles the situation when firmware crashes.
When firmware crashes, it will send an interrupt, and driver will queue
a work for recovery.
In the work, driver will reset it's internal association state, which
includes removing associated sta's macid, resetting vifs' states
and removing keys. After resetting the driver's state, driver will call
rtw_enter_ips() to force the chipset power off to reset the chip.
Finally, driver calls ieee80211_restart_hw() to inform mac80211 stack
to restart.
Since only 8822c firmware supports this feature, the interrupt will only
be triggered when 8822c chipset is loaded.
Signed-off-by: Tzu-En Huang <tehuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200925061219.23754-3-tehuang@realtek.com
|
|
Enable/disable beacon accordingly when the BSS info changed.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-7-yhchuang@realtek.com
|
|
Sometimes mac80211 will just ask driver to change the interface
instead of to remove and then add a new one. And for driver, to
change the interface is just simply to remove and add a new one
but change the type of it.
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200717064937.27966-6-yhchuang@realtek.com
|
