| Age | Commit message (Collapse) | Author |
|---|
|
Add support for driver-specific devlink local_forwarding param.
Supported values are "enabled", "disabled" and "prioritized".
Default configuration is set to "enabled".
Add documentation in networking/devlink/ice.rst.
In previous generations of Intel NICs the transmit scheduler was only
limited by PCIe bandwidth when scheduling/assigning hairpin-bandwidth
between VFs. Changes to E810 HW design introduced scheduler limitation,
so that available hairpin-bandwidth is bound to external port speed.
In order to address this limitation and enable NFV services such as
"service chaining" a knob to adjust the scheduler config was created.
Driver can send a configuration message to the FW over admin queue and
internal FW logic will reconfigure HW to prioritize and add more BW to
VF to VF traffic. An end result, for example, 10G port will no longer
limit hairpin-bandwidth to 10G and much higher speeds can be achieved.
Devlink local_forwarding param set to "prioritized" enables higher
hairpin-bandwitdh on related PFs. Configuration is applicable only to
8x10G and 4x25G cards.
Changing local_forwarding configuration will trigger CORER reset in
order to take effect.
Example command to change current value:
devlink dev param set pci/0000:b2:00.3 name local_forwarding \
value prioritized \
cmode runtime
Co-developed-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
To debug link issues in the field, serdes Tx/Rx equalizer values
help to determine the health of serdes lane.
Extend 'ethtool -d' option to dump serdes Tx/Rx equalizer.
The following list of equalizer param is supported
a. rx_equalization_pre2
b. rx_equalization_pre1
c. rx_equalization_post1
d. rx_equalization_bflf
e. rx_equalization_bfhf
f. rx_equalization_drate
g. tx_equalization_pre1
h. tx_equalization_pre3
i. tx_equalization_atten
j. tx_equalization_post1
k. tx_equalization_pre2
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anil Samal <anil.samal@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20240709202951.2103115-4-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add new device capability ICE_AQC_CAPS_NAC_TOPOLOGY which allows to
determine the mode of operation (1 or 2 NAC).
Define a new structure to store data from new capability and
corresponding parser code.
Co-developed-by: Prathisna Padmasanan <prathisna.padmasanan@intel.com>
Signed-off-by: Prathisna Padmasanan <prathisna.padmasanan@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Pawel Kaminski <pawel.kaminski@intel.com>
Reviewed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20240528-next-2024-05-28-ptp-refactors-v1-10-c082739bb6f6@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
It was observed that Tx performance was inconsistent across all queues
and/or VSIs and that it was directly connected to existing 9-layer
topology of the Tx scheduler.
Introduce new private devlink param - tx_scheduling_layers. This parameter
gives user flexibility to choose the 5-layer transmit scheduler topology
which helps to smooth out the transmit performance.
Allowed parameter values are 5 and 9.
Example usage:
Show:
devlink dev param show pci/0000:4b:00.0 name tx_scheduling_layers
pci/0000:4b:00.0:
name tx_scheduling_layers type driver-specific
values:
cmode permanent value 9
Set:
devlink dev param set pci/0000:4b:00.0 name tx_scheduling_layers value 5
cmode permanent
devlink dev param set pci/0000:4b:00.0 name tx_scheduling_layers value 9
cmode permanent
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Co-developed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There is a performance issue when the number of VSIs are not multiple
of 8. This is caused due to the max children limitation per node(8) in
9 layer topology. The BW credits are shared evenly among the children
by default. Assume one node has 8 children and the other has 1.
The parent of these nodes share the BW credit equally among them.
Apparently this causes a problem for the first node which has 8 children.
The 9th VM get more BW credits than the first 8 VMs.
Example:
1) With 8 VM's:
for x in 0 1 2 3 4 5 6 7;
do taskset -c ${x} netperf -P0 -H 172.68.169.125 & sleep .1 ; done
tx_queue_0_packets: 23283027
tx_queue_1_packets: 23292289
tx_queue_2_packets: 23276136
tx_queue_3_packets: 23279828
tx_queue_4_packets: 23279828
tx_queue_5_packets: 23279333
tx_queue_6_packets: 23277745
tx_queue_7_packets: 23279950
tx_queue_8_packets: 0
2) With 9 VM's:
for x in 0 1 2 3 4 5 6 7 8;
do taskset -c ${x} netperf -P0 -H 172.68.169.125 & sleep .1 ; done
tx_queue_0_packets: 24163396
tx_queue_1_packets: 24164623
tx_queue_2_packets: 24163188
tx_queue_3_packets: 24163701
tx_queue_4_packets: 24163683
tx_queue_5_packets: 24164668
tx_queue_6_packets: 23327200
tx_queue_7_packets: 24163853
tx_queue_8_packets: 91101417
So on average queue 8 statistics show that 3.7 times more packets were
send there than to the other queues.
The FW starting with version 3.20, has increased the max number of
children per node by reducing the number of layers from 9 to 5. Reflect
this on driver side.
Signed-off-by: Raj Victor <victor.raj@intel.com>
Co-developed-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Co-developed-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
New E810 firmware supports the corresponding functionality, so the driver
allows PFs to subscribe the same switch recipes. Then when the PF is done
with a switch recipes, the PF can ask firmware to free that switch recipe.
When users configure a rule to PFn into E810 switch component, if there is
no existing recipe matching this rule's pattern, the driver will request
firmware to allocate and return a new recipe resource for the rule by
calling ice_add_sw_recipe() and ice_alloc_recipe(). If there is an existing
recipe matching this rule's pattern with different key value, or this is a
same second rule to PFm into switch component, the driver checks out this
recipe by calling ice_find_recp(), the driver will tell firmware to share
using this same recipe resource by calling ice_subscribable_recp_shared()
and ice_subscribe_recipe().
When firmware detects that all subscribing PFs have freed the switch
recipe, firmware will free the switch recipe so that it can be reused.
This feature also fixes a problem where all switch recipes would eventually
be exhausted because switch recipes could not be freed, as freeing a shared
recipe could potentially break other PFs that were using it.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Steven Zou <steven.zou@intel.com>
Tested-by: Mayank Sharma <mayank.sharma@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
According to the datasheet, the recipe association data is an 8-byte
little-endian value. It is described as 'Bitmap of the recipe indexes
associated with this profile', it is from 24 to 31 byte area in FW.
Therefore, it is defined to '__le64 recipe_assoc' in struct
ice_aqc_recipe_to_profile. And then fix the bitmap casting issue, as we
must never ever use castings for bitmap type.
Fixes: 1e0f9881ef79 ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Jan Sokolowski <jan.sokolowski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Steven Zou <steven.zou@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Cross-merge networking fixes after downstream PR.
Conflicts:
drivers/net/ethernet/broadcom/bnxt/bnxt.c
e009b2efb7a8 ("bnxt_en: Remove mis-applied code from bnxt_cfg_ntp_filters()")
0f2b21477988 ("bnxt_en: Fix compile error without CONFIG_RFS_ACCEL")
https://lore.kernel.org/all/20240105115509.225aa8a2@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Get link status version 2 (opcode 0x0607) is returning an error because FW
expects a data length of 56 bytes, and this is causing the driver to fail
probe.
Update the get link status version 2 data length to 56 bytes by adding 5
byte reserved5 field to the end of struct ice_aqc_get_link_status_data and
passing it as parameter to offsetofend() to the fix error.
Fixes: 2777d24ec6d1 ("ice: Add ice_get_link_status_datalen")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
While converting to FIELD_PREP() and FIELD_GET(), it was noticed that
some of the RSS defines had *included* the shift in their definitions.
This is completely outside of normal, such that a developer could easily
make a mistake and shift at the usage site (like when using
FIELD_PREP()).
Rename the defines and set them to the "pre-shifted values" so they
match the template the driver normally uses for masks and the member
bits of the mask, which also allows the driver to use FIELD_PREP
correctly with these values. Use GENMASK() for this changed MASK value.
Do the same for the VLAN EMODE defines as well.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Once logging is enabled the user should read the data from the 'data'
file. The data is in the form of a binary blob that can be sent to Intel
for decoding. To read the data use a command like:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/data > log_data.bin
If the user wants to clear the FW log data that has been stored in the
driver then they can write any value to the 'data' file and that will clear
the data. An example is:
# echo 34 > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/data
In addition to being able to read the data the user can configure how
much memory is used to store FW log data. This allows the user to
increase/decrease the amount of memory based on the users situation.
The data is stored such that if the memory fills up then the oldest data
will get overwritten in a circular manner. To change the amount of
memory the user can write to the 'log_size' file like this:
# echo <value> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/log_size
Where <value> is one of 128K, 256K, 512K, 1M, and 2M. The default value
is 1M.
The user can see the current value of 'log_size' by reading the file:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/log_size
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Once users have configured the FW logging then allow them to enable it
by writing to the 'fwlog/enable' file. The file accepts a boolean value
(0 or 1) where 1 means enable FW logging and 0 means disable FW logging.
# echo <value> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/enable
Where <value> is 0 or 1.
The user can read the 'fwlog/enable' file to see whether logging is
enabled or not. Reading the actual data is a separate patch. To see the
current value then:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/enable
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Users want the ability to debug FW issues by retrieving the
FW logs from the E8xx devices. Use debugfs to allow the user to
configure the log level and number of messages for FW logging.
If FW logging is supported on the E8xx then the file 'fwlog' will be
created under the PCI device ID for the ice driver. If the file does not
exist then either the E8xx doesn't support FW logging or debugfs is not
enabled on the system.
One thing users want to do is control which events are reported. The
user can read and write the 'fwlog/modules/<module name>' to get/set
the log levels. Each module in the FW that supports logging ht as a file
under 'fwlog/modules' that supports reading (to see what the current log
level is) and writing (to change the log level).
The format to set the log levels for a module are:
# echo <log level> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/<module>
The supported log levels are:
* none
* error
* warning
* normal
* verbose
Each level includes the messages from the previous/lower level
The modules that are supported are:
* general
* ctrl
* link
* link_topo
* dnl
* i2c
* sdp
* mdio
* adminq
* hdma
* lldp
* dcbx
* dcb
* xlr
* nvm
* auth
* vpd
* iosf
* parser
* sw
* scheduler
* txq
* rsvd
* post
* watchdog
* task_dispatch
* mng
* synce
* health
* tsdrv
* pfreg
* mdlver
* all
The module 'all' is a special module which allows the user to read or
write to all of the modules.
The following example command would set the DCB module to the 'normal'
log level:
# echo normal > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
If the user wants to set the DCB, Link, and the AdminQ modules to
'verbose' then the commands are:
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/link
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/adminq
If the user wants to set all modules to the 'warning' level then the
command is:
# echo warning > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
If the user wants to disable logging for a module then they can set the
level to 'none'. An example setting the 'watchdog' module is:
# echo none > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/watchdog
If the user wants to see what the log level is for a specific module
then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
This will return the log level for the DCB module. If the user wants to
see the log level for all the modules then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
Writing to the module file will update the configuration, but NOT enable the
configuration (that is a separate command).
In addition to configuring the modules, the user can also configure the
number of log messages (nr_messages) to include in a single Admin Receive
Queue (ARQ) event.The range is 1-128 (1 means push every log message, 128
means push only when the max AQ command buffer is full). The suggested
value is 10.
To see/change the resolution the user can read/write the
'fwlog/nr_messages' file. An example changing the value to 50 is
# echo 50 > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
To see the current value of 'nr_messages' then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The FW logging code doesn't work because there is no way to set
cq_ena or uart_ena so remove the code. This code is the original
(v1) way of FW logging so it should be replaced with the v2 way.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Fix the values of the ICE_AQ_VSI_Q_OPT_RSS_* registers. Shifting is
already done when the values are used, no need to double shift. Bug was
not discovered earlier since only ICE_AQ_VSI_Q_OPT_RSS_TPLZ (Zero) is
currently used.
Also, rename ICE_AQ_VSI_Q_OPT_RSS_XXX to ICE_AQ_VSI_Q_OPT_RSS_HASH_XXX
for consistency.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-5-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since 4.30 firmware exposes internal thermal sensor reading via admin
queue commands. Expose those readouts via hwmon API when supported.
Datasheet:
Get Sensor Reading Command (Opcode: 0x0632)
+--------------------+--------+--------------------+-------------------------+
| Name | Bytes | Value | Remarks |
+--------------------+--------+--------------------+-------------------------+
| Flags | 1-0 | | |
| Opcode | 2-3 | 0x0632 | Command opcode |
| Datalen | 4-5 | 0 | No external buffer. |
| Return value | 6-7 | | Return value. |
| Cookie High | 8-11 | Cookie | |
| Cookie Low | 12-15 | Cookie | |
| Sensor | 16 | | 0x00: Internal temp |
| | | | 0x01-0xFF: Reserved. |
| Format | 17 | Requested response | Only 0x00 is supported. |
| | | format | 0x01-0xFF: Reserved. |
| Reserved | 18-23 | | |
| Data Address high | 24-27 | Response buffer | |
| | | address | |
| Data Address low | 28-31 | Response buffer | |
| | | address | |
+--------------------+--------+--------------------+-------------------------+
Get Sensor Reading Response (Opcode: 0x0632)
+--------------------+--------+--------------------+-------------------------+
| Name | Bytes | Value | Remarks |
+--------------------+--------+--------------------+-------------------------+
| Flags | 1-0 | | |
| Opcode | 2-3 | 0x0632 | Command opcode |
| Datalen | 4-5 | 0 | No external buffer |
| Return value | 6-7 | | Return value. |
| | | | EINVAL: Invalid |
| | | | parameters |
| | | | ENOENT: Unsupported |
| | | | sensor |
| | | | EIO: Sensor access |
| | | | error |
| Cookie High | 8-11 | Cookie | |
| Cookie Low | 12-15 | Cookie | |
| Sensor Reading | 16-23 | | Format of the reading |
| | | | is dependent on request |
| Data Address high | 24-27 | Response buffer | |
| | | address | |
| Data Address low | 28-31 | Response buffer | |
| | | address | |
+--------------------+--------+--------------------+-------------------------+
Sensor Reading for Sensor 0x00 (Internal Chip Temperature):
+--------------------+--------+--------------------+-------------------------+
| Name | Bytes | Value | Remarks |
+--------------------+--------+--------------------+-------------------------+
| Thermal Sensor | 0 | | Reading in degrees |
| reading | | | Celsius. Signed int8 |
| Warning High | 1 | | Warning High threshold |
| threshold | | | in degrees Celsius. |
| | | | Unsigned int8. |
| | | | 0xFF when unsupported |
| Critical High | 2 | | Critical High threshold |
| threshold | | | in degrees Celsius. |
| | | | Unsigned int8. |
| | | | 0xFF when unsupported |
| Fatal High | 3 | | Fatal High threshold |
| threshold | | | in degrees Celsius. |
| | | | Unsigned int8. |
| | | | 0xFF when unsupported |
| Reserved | 4-7 | | |
+--------------------+--------+--------------------+-------------------------+
Driver provides current reading from HW as well as device specific
thresholds for thermal alarm (Warning, Critical, Fatal) events.
$ sensors
Output
=========================================================
ice-pci-b100
Adapter: PCI adapter
temp1: +62.0°C (high = +95.0°C, crit = +105.0°C)
(emerg = +115.0°C)
Tested on Intel Corporation Ethernet Controller E810-C for SFP
Co-developed-by: Marcin Domagala <marcinx.domagala@intel.com>
Signed-off-by: Marcin Domagala <marcinx.domagala@intel.com>
Co-developed-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Eric Joyner <eric.joyner@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Konrad Knitter <konrad.knitter@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The Get Link Status data length can vary with different versions of
ice_aqc_get_link_status_data. Add ice_get_link_status_datalen() to return
datalen for the specific ice_aqc_get_link_status_data version.
Add new link partner fields to ice_aqc_get_link_status_data; PHY type,
FEC, and flow control.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-4-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the support for 200G phy speeds and the mapping for their
advertisement in link. Add the new PHY type bits for AQ command, as
needed for 200G E830 controllers.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The only feature using the Firmware (FW) shared parameters was the PTP
clock ID. Since this ID is now shared using auxiliary buss - remove the
FW shared parameters from the code.
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The PHC clock id used to be moved between PFs using FW admin queue
shared parameters - move the implementation to auxiliary bus.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Similar to the change made for ICE_F_SMA_CTRL, check the netlist before
enabling support for ICE_F_GNSS. This ensures that the driver only enables
the GNSS feature on devices which actually have the feature enabled in the
firmware device configuration.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add firmware admin command to access clock generation unit
configuration, it is required to enable Extended PTP and SyncE features
in the driver.
Add definitions of possible hardware variations of input and output pins
related to clock generation unit and functions to access the data.
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Signed-off-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor __ice_aq_get_set_rss_lut() to improve reader experience and limit
misuse scenarios (undesired LUT size for given LUT type).
Allow only 3 RSS LUT type+size variants:
PF LUT sized 2048, GLOBAL LUT sized 512, and VSI LUT sized 64, which were
used on default flows prior to this commit.
Prior to the change, code was mixing the meaning of @params->lut_size and
@params->lut_type, flag assigning logic was cryptic, while long defines
made everything harder to follow.
Fix that by extracting some code out to separate helpers.
Drop some of "shift by 0" statements that originated from Intel's
internal HW documentation.
Drop some redundant VSI masks (since ice_is_vsi_valid() gives "valid" for
up to 0x300 VSIs).
After sweeping all the defines out of struct ice_aqc_get_set_rss_lut,
it fits into 7 lines.
Finally apply some cleanup to the callsite
(use of the new enums, tmp var for lengthy bit extraction).
Note that flags for 128 and 64 sized VSI LUT are the same,
and 64 is used everywhere in the code (updated to new enum here), it just
happened that there was 128 in flag name.
__ice_aq_get_set_rss_key() uses the same VSI valid bit, make constant
common for it and __ice_aq_get_set_rss_lut().
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add a function to find the C827 PHY node handle and return C827 PHY
index for the E810 products.
In order to bring this function to full functionality, some
helpers for this were written by Michal Michalik.
Co-developed-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add defines needed for interaction with the FW admin queue interface
in relation to supporting LAG and SRIOV VFs interacting.
Add code, or make non-static previously static functions, to access
the new and changed admin queue calls for LAG.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add the defines, fields, and detection code for FW support of LAG for
SRIOV. Also exposes some previously static functions to allow access
in the lag code.
Clean up code that is unused or not needed for LAG support. Also add
an ordered workqueue for processing LAG events.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
ICE_PHY_TYPE_HIGH_MAX_INDEX should be the maximum index value and not the
length/number of ICE_PHY_TYPE_HIGH. This is not an issue because this
define is only used when calling ice_get_link_speed_based_on_phy_type(),
which will return ICE_AQ_LINK_SPEED_UNKNOWN for any invalid index. The
caller of ice_get_link_speed_based_on_phy_type(), ice_update_phy_type()
checks that the return value is a valid link speed before using it and
ICE_AQ_LINK_SPEED_UNKNOWN is not. However, update the define to reflect
the correct value.
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In DCB Willing Mode (FW managed LLDP), when the link partner changes
configuration which requires fewer TCs, the TCs that are no longer
needed are suspended by EMP FW, removed, and never resumed. This occurs
before a MIB change event is indicated to SW. The permanent suspension and
removal of these TC nodes in the scheduler prevents RDMA from being able
to destroy QPs associated with this TC, requiring a CORE reset to recover.
A new DCBX configuration change flow is defined to allow SW driver and
other SW components (RDMA) to properly adjust to the configuration
changes before they are taking effect in HW. This flow includes a
two-way handshake between EMP FW<->LAN SW<->RDMA SW.
List of changes:
- Add 'Execute Pending LLDP MIB' AQC.
- Add 'Pending Event Enable' bit.
- Add additional logic to ignore Pending Event Enable' request
while 'LLDP MIB Chnage' event is disabled.
- Add 'Execute Pending LLDP MIB' AQC sending function to FW,
which is needed to take place MIB Event change.
Signed-off-by: Tsotne Chakhvadze <tsotne.chakhvadze@intel.com>
Co-developed-by: Karen Sornek <karen.sornek@intel.com>
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Co-developed-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
To support new devlink-rate API ice_sched_node struct needs to store
a number of additional parameters. This includes tx_max, tx_share,
tx_weight, and tx_priority.
Add new fields to ice_sched_node struct. Add new functions to configure
the hardware with new parameters. Introduce new xarray to identify
nodes uniquely.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The ice_nvm_write_activate function is used to issue AdminQ command
0x0707 which sends a request to firmware to activate a flash bank. For
basic operations, this command takes an 8bit flag value which defines
the flags to control the activation process. There are some additional
flags that are stored in a second 8bit flag field.
We can simplify the interface by using a u16 cmd_flags variable. Split
this over the two bytes of flag storage in the structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement support for Get/Set Port Options admin queue commands
(0x06EA/0x06EB). These firmware commands allow the driver to change port
specific options and will be used in the next patch.
Co-developed-by: Lev Faerman <lev.faerman@intel.com>
Signed-off-by: Lev Faerman <lev.faerman@intel.com>
Co-developed-by: Damian Milosek <damian.milosek@intel.com>
Signed-off-by: Damian Milosek <damian.milosek@intel.com>
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add the possibility to write to connected i2c devices using the AQ
command. FW may reject the write if the device is not on allowlist.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Global `-Warray-bounds` enablement revealed some problems, one of
which is the way we define and use AQC rules messages.
In fact, they have a shared header, followed by the actual message,
which can be of one of several different formats. So it is
straightforward enough to define that header as a separate struct
and then embed it into message structures as needed, but currently
all the formats reside in one union coupled with the header. Then,
the code allocates only the memory needed for a particular message
format, leaving the union potentially incomplete.
There are no actual reads or writes beyond the end of an allocated
chunk, but at the same time, the whole implementation is fragile and
backed by an equilibrium rather than strong type and memory checks.
Define the structures the other way around: one for the common
header and the rest for the actual formats with the header embedded.
There are no places where several union members would be used at the
same time anyway. This allows to use proper struct_size() and let
the compiler know what is going to be done.
Finally, unsilence `-Warray-bounds` back for ice_switch.c.
Other little things worth mentioning:
* &ice_sw_rule_vsi_list_query is not used anywhere, remove it. It's
weird anyway to talk to hardware with purely kernel types
(bitmaps);
* expand the ICE_SW_RULE_*_SIZE() macros to pass a structure
variable name to struct_size() to let it do strict typechecking;
* rename ice_sw_rule_lkup_rx_tx::hdr to ::hdr_data to keep ::hdr
for the header structure to have the same name for it constistenly
everywhere;
* drop the duplicate of %ICE_SW_RULE_RX_TX_NO_HDR_SIZE residing in
ice_switch.h.
Fixes: 9daf8208dd4d ("ice: Add support for switch filter programming")
Fixes: 66486d8943ba ("ice: replace single-element array used for C struct hack")
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20220601105924.2841410-1-alexandr.lobakin@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add a new ice_gnss.c file for holding the basic GNSS module functions.
If the device supports GNSS module, call the new ice_gnss_init and
ice_gnss_release functions where appropriate.
Implement basic functionality for reading the data from GNSS module
using TTY device.
Add I2C read AQ command. It is now required for controlling the external
physical connectors via external I2C port expander on E810-T adapters.
Future changes will introduce write functionality.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sudhansu Sekhar Mishra <sudhansu.mishra@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support configuring the device in Double VLAN Mode (DVM),
the DDP and FW have to support DVM. If both support DVM, the PF that
downloads the package needs to update the default recipes, set the
VLAN mode, and update boost TCAM entries.
To support updating the default recipes in DVM, add support for
updating an existing switch recipe's lkup_idx and mask. This is done
by first calling the get recipe AQ (0x0292) with the desired recipe
ID. Then, if that is successful update one of the lookup indices
(lkup_idx) and its associated mask if the mask is valid otherwise
the already existing mask will be used.
The VLAN mode of the device has to be configured while the global
configuration lock is held while downloading the DDP, specifically after
the DDP has been downloaded. If supported, the device will default to
DVM.
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Current operations act on inner VLAN fields. To support double VLAN, outer
VLAN operations and functions will be implemented. Add the "inner" naming
to existing VLAN operations to distinguish them from the upcoming outer
values and functions. Some spacing adjustments are made to align
values.
Note that the inner is not talking about a tunneled VLAN, but the second
VLAN in the packet. For SVM the driver uses inner or single VLAN
filtering and offloads and in Double VLAN Mode the driver uses the
inner filtering and offloads for SR-IOV VFs in port VLANs in order to
support offloading the guest VLAN while a port VLAN is configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Some devices have support for loading the PHY FW and in some cases this
can fail. When this fails, the FW will set the corresponding bit in the
link info structure. Also, the FW will send a link event if the correct
link event mask bit is set. Add support for printing an error message
when the PHY FW load fails during any link configuration flow and the
link event flow.
Since ice_check_module_power() is already doing something very similar
add a new function ice_check_link_cfg_err() so any failures reported in
the link info's link_cfg_err member can be printed in this one function.
Also, add the new ICE_FLAG_PHY_FW_LOAD_FAILED bit to the PF's flags so
we don't constantly print this error message during link polling if the
value never changed.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E810-T adapters have two external bidirectional SMA connectors and two
internal unidirectional U.FL connectors. Multiplexing between U.FL and
SMA and SMA direction is controlled using the PCA9575 expander.
Add support for the PCA9575 detection and control of the respective pins
of the SMA/U.FL multiplexer using the GPIO AQ API.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement ice_aq_get_gpio and ice_aq_set_gpio for reading and changing
the state of GPIO pins described in the topology.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Separate link topo parameters in struct ice_aqc_link_topo_addr into
new struct ice_aqc_link_topo_params.
This keeps input parameters for the get_link_topo command in a separate
structure and is required by future commands that operate only on link
topo params without the node handle.
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add code to manage recipes and profiles on admin queue layer.
Allow the driver to add a new recipe and update an existing one. Get a
recipe and get a recipe to profile association is mostly used in update
existing recipes code.
Only default recipes can be updated. An update is done by reading recipes
from HW, changing their params and calling add recipe command.
Support following admin queue commands:
- ice_aqc_opc_add_recipe (0x0290) - create a recipe with protocol
header information and other details that determine how this recipe
filter works
- ice_aqc_opc_recipe_to_profile (0x0291) - associate a switch recipe
to a profile
- ice_aqc_opc_get_recipe (0x0292) - get details of an existing recipe
- ice_aqc_opc_get_recipe_to_profile (0x0293) - get a recipe associated
with profile ID
Define ICE_AQC_RES_TYPE_RECIPE resource type to hold a switch
recipe. It is needed when a new switch recipe needs to be created.
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Grishma Kotecha <grishma.kotecha@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Implement code to handle submission of APP TLV's
containing DSCP to TC mapping.
The first such mapping received on an interface
will cause that PF to switch to L3 DSCP QoS mode,
apply the default config for that mode, and apply
the received mapping.
Only one such mapping will be allowed per DSCP value,
and when the last DSCP mapping is deleted, the PF
will switch back into L2 VLAN QoS mode, applying the
appropriate default QoS settings.
L3 DSCP QoS mode will only be allowed in SW DCBx
mode, in other words, when the FW LLDP engine is
disabled. Commands that break this mutual exclusivity
will be blocked.
Co-developed-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Depending on the device configuration, the ice hardware may share the
PTP hardware clock timer between multiple PFs. Each PF is informed by
firmware during initialization of the PTP timer association.
When bringing up PTP, only the PFs which own the timer shall allocate
a PTP hardware clock. Other PFs associated with that timer must report
the correct PTP clock index in order to allow userspace software the
ability to know which ports are connected to the same clock.
To support this, the firmware has driver shared parameters. These
parameters enable one PF to write the clock index into firmware, and
have other PFs read the associated value out. This enables the driver to
have only a single PF allocate and control the device timer registers,
while other PFs associated with that timer can report the correct clock
in the ETHTOOL_GET_TS_INFO report.
Add support for the necessary admin queue commands to enable reading and
writing of the driver shared parameters. This will be used in a future
change to enable sharing the PTP clock index between PF drivers.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The device firmware reports PTP clock capabilities to each PF during
initialization. This includes various information for both the overall
device and the individual function, including
For functions:
* whether this function has timesync enabled
* whether this function owns one of the 2 possible clock timers, and
which one
* which timer the function is associated with
* the clock frequency, if the device supports multiple clock frequencies
* The GPIO pin association for the timer owned by this PF, if any
For the device:
* Which PF owns timer 0, if any
* Which PF owns timer 1, if any
* whether timer 0 is enabled
* whether timer 1 is enabled
Extract the bits from the capabilities information reported by firmware
and store them in the device and function capability structures.o
This information will be used in a future change to have the function
driver enable PTP hardware clock support.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In order to support certain device features, including enabling the PTP
hardware clock, the ice driver needs to control some registers on the
device PHY.
These registers are accessed by sending sideband messages. For some
hardware, these messages must be sent over the device admin queue, while
other hardware has a dedicated control queue for the sideband messages.
Add the neighbor device message structure for sending a message to the
neighboring device. Where supported, initialize the sideband control
queue and handle cleanup.
Add a wrapper function for sending sideband control queue messages that
read or write a neighboring device register.
Because some devices send sideband messages over the AdminQ, also
increase the length of the admin queue to allow more messages to be
queued up. This is important because the sideband messages add
additional pressure on the AQ usage.
This support will be used in following patches to enable support for
CONFIG_1588_PTP_CLOCK.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Determine whether an unsupported power configuration is preventing link
establishment by storing and checking the link_cfg_err_byte. Print error
messages when module power levels are unsupported. Also add a new flag
bit to prevent spamming said error messages.
Co-developed-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Add implementations for supporting iidc operations for device operation
such as allocation of resources and event notifications.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Probe the device's capabilities to see if it supports RDMA. If so, allocate
and reserve resources to support its operation; populate structures with
initial values.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Signed-off-by: Shiraz Saleem <shiraz.saleem@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Recent firmware supports a new "get PHY capabilities" mode
ICE_AQC_REPORT_DFLT_CFG which makes it unnecessary for the driver
to track and apply NVM based default link overrides.
If FW AQ API version supports it, use Report Default Configuration.
Add check function for Report Default Configuration support and update
accordingly.
Also change adv_phy_type_[lo|hi] to advert_phy_type[lo|hi] for
clarity.
Co-developed-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Mateusz Pacuszka <mateuszx.pacuszka@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
