| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking fixes from David Miller:
1) Disable RISCV BPF JIT builds when !MMU, from Björn Töpel.
2) nf_tables leaves dangling pointer after free, fix from Eric Dumazet.
3) Out of boundary write in __xsk_rcv_memcpy(), fix from Li RongQing.
4) Adjust icmp6 message source address selection when routes have a
preferred source address set, from Tim Stallard.
5) Be sure to validate HSR protocol version when creating new links,
from Taehee Yoo.
6) CAP_NET_ADMIN should be sufficient to manage l2tp tunnels even in
non-initial namespaces, from Michael Weiß.
7) Missing release firmware call in mlx5, from Eran Ben Elisha.
8) Fix variable type in macsec_changelink(), caught by KASAN. Fix from
Taehee Yoo.
9) Fix pause frame negotiation in marvell phy driver, from Clemens
Gruber.
10) Record RX queue early enough in tun packet paths such that XDP
programs will see the correct RX queue index, from Gilberto Bertin.
11) Fix double unlock in mptcp, from Florian Westphal.
12) Fix offset overflow in ARM bpf JIT, from Luke Nelson.
13) marvell10g needs to soft reset PHY when coming out of low power
mode, from Russell King.
14) Fix MTU setting regression in stmmac for some chip types, from
Florian Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (101 commits)
amd-xgbe: Use __napi_schedule() in BH context
mISDN: make dmril and dmrim static
net: stmmac: dwmac-sunxi: Provide TX and RX fifo sizes
net: dsa: mt7530: fix tagged frames pass-through in VLAN-unaware mode
tipc: fix incorrect increasing of link window
Documentation: Fix tcp_challenge_ack_limit default value
net: tulip: make early_486_chipsets static
dt-bindings: net: ethernet-phy: add desciption for ethernet-phy-id1234.d400
ipv6: remove redundant assignment to variable err
net/rds: Use ERR_PTR for rds_message_alloc_sgs()
net: mscc: ocelot: fix untagged packet drops when enslaving to vlan aware bridge
selftests/bpf: Check for correct program attach/detach in xdp_attach test
libbpf: Fix type of old_fd in bpf_xdp_set_link_opts
libbpf: Always specify expected_attach_type on program load if supported
xsk: Add missing check on user supplied headroom size
mac80211: fix channel switch trigger from unknown mesh peer
mac80211: fix race in ieee80211_register_hw()
net: marvell10g: soft-reset the PHY when coming out of low power
net: marvell10g: report firmware version
net/cxgb4: Check the return from t4_query_params properly
...
|
|
This patch fixes an incorrect check in how immediate memory offsets are
computed for BPF_DW on arm.
For BPF_LDX/ST/STX + BPF_DW, the 32-bit arm JIT breaks down an 8-byte
access into two separate 4-byte accesses using off+0 and off+4. If off
fits in imm12, the JIT emits a ldr/str instruction with the immediate
and avoids the use of a temporary register. While the current check off
<= 0xfff ensures that the first immediate off+0 doesn't overflow imm12,
it's not sufficient for the second immediate off+4, which may cause the
second access of BPF_DW to read/write the wrong address.
This patch fixes the problem by changing the check to
off <= 0xfff - 4 for BPF_DW, ensuring off+4 will never overflow.
A side effect of simplifying the check is that it now allows using
negative immediate offsets in ldr/str. This means that small negative
offsets can also avoid the use of a temporary register.
This patch introduces no new failures in test_verifier or test_bpf.c.
Fixes: c5eae692571d6 ("ARM: net: bpf: improve 64-bit store implementation")
Fixes: ec19e02b343db ("ARM: net: bpf: fix LDX instructions")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200409221752.28448-1-luke.r.nels@gmail.com
|
|
Commit
0698fac4ac2a ("efi/arm: Clean EFI stub exit code from cache instead of avoiding it")
introduced a PC-relative reference to 'call_cache_fn' into
efi_enter_kernel(), which lives way at the end of head.S. In some cases,
the ARM version of the ADR instruction does not have sufficient range,
resulting in a build error:
arch/arm/boot/compressed/head.S:1453: Error: invalid constant (fffffffffffffbe4) after fixup
ARM defines an alternative with a wider range, called ADRL, but this does
not exist for Thumb-2. At the same time, the ADR instruction in Thumb-2
has a wider range, and so it does not suffer from the same issue.
So let's switch to ADRL for ARM builds, and keep the ADR for Thumb-2 builds.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200409130434.6736-6-ardb@kernel.org
|
|
For security reasons I stopped using gmail account and kernel address is
now up-to-date alias to my personal address.
People periodically send me emails to address which they found in source
code of drivers, so this change reflects state where people can contact
me.
[ Added .mailmap entry as per Joe Perches - Linus ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Joe Perches <joe@perches.com>
Link: http://lkml.kernel.org/r/20200307104237.8199-1-pali@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently there are many platforms that dont enable ARCH_HAS_PTE_SPECIAL
but required to define quite similar fallback stubs for special page
table entry helpers such as pte_special() and pte_mkspecial(), as they
get build in generic MM without a config check. This creates two
generic fallback stub definitions for these helpers, eliminating much
code duplication.
mips platform has a special case where pte_special() and pte_mkspecial()
visibility is wider than what ARCH_HAS_PTE_SPECIAL enablement requires.
This restricts those symbol visibility in order to avoid redefinitions
which is now exposed through this new generic stubs and subsequent build
failure. arm platform set_pte_at() definition needs to be moved into a
C file just to prevent a build failure.
[anshuman.khandual@arm.com: use defined(CONFIG_ARCH_HAS_PTE_SPECIAL) in mips per Thomas]
Link: http://lkml.kernel.org/r/1583851924-21603-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Guo Ren <guoren@kernel.org> [csky]
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> [m68k]
Acked-by: Stafford Horne <shorne@gmail.com> [openrisc]
Acked-by: Helge Deller <deller@gmx.de> [parisc]
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Sam Creasey <sammy@sammy.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Link: http://lkml.kernel.org/r/1583802551-15406-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are many places where all basic VMA access flags (read, write,
exec) are initialized or checked against as a group. One such example
is during page fault. Existing vma_is_accessible() wrapper already
creates the notion of VMA accessibility as a group access permissions.
Hence lets just create VM_ACCESS_FLAGS (VM_READ|VM_WRITE|VM_EXEC) which
will not only reduce code duplication but also extend the VMA
accessibility concept in general.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Springer <rspringer@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Link: http://lkml.kernel.org/r/1583391014-8170-3-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are many platforms with exact same value for VM_DATA_DEFAULT_FLAGS
This creates a default value for VM_DATA_DEFAULT_FLAGS in line with the
existing VM_STACK_DEFAULT_FLAGS. While here, also define some more
macros with standard VMA access flag combinations that are used
frequently across many platforms. Apart from simplification, this
reduces code duplication as well.
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Guo Ren <guoren@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rich Felker <dalias@libc.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Chris Zankel <chris@zankel.net>
Link: http://lkml.kernel.org/r/1583391014-8170-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-04-10
The following pull-request contains BPF updates for your *net* tree.
We've added 13 non-merge commits during the last 7 day(s) which contain
a total of 13 files changed, 137 insertions(+), 43 deletions(-).
The main changes are:
1) JIT code emission fixes for riscv and arm32, from Luke Nelson and Xi Wang.
2) Disable vmlinux BTF info if GCC_PLUGIN_RANDSTRUCT is used, from Slava Bacherikov.
3) Fix oob write in AF_XDP when meta data is used, from Li RongQing.
4) Fix bpf_get_link_xdp_id() handling on single prog when flags are specified,
from Andrey Ignatov.
5) Fix sk_assign() BPF helper for request sockets that can have sk_reuseport
field uninitialized, from Joe Stringer.
6) Fix mprotect() test case for the BPF LSM, from KP Singh.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current arm BPF JIT does not correctly compile RSH or ARSH when the
immediate shift amount is 0. This causes the "rsh64 by 0 imm" and "arsh64
by 0 imm" BPF selftests to hang the kernel by reaching an instruction
the verifier determines to be unreachable.
The root cause is in how immediate right shifts are encoded on arm.
For LSR and ASR (logical and arithmetic right shift), a bit-pattern
of 00000 in the immediate encodes a shift amount of 32. When the BPF
immediate is 0, the generated code shifts by 32 instead of the expected
behavior (a no-op).
This patch fixes the bugs by adding an additional check if the BPF
immediate is 0. After the change, the above mentioned BPF selftests pass.
Fixes: 39c13c204bb11 ("arm: eBPF JIT compiler")
Co-developed-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20200408181229.10909-1-luke.r.nels@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight
Pull backlight updates from Lee Jones:
"Switch pwm_bl and corgi_lcd drivers to use GPIO descriptors"
* tag 'backlight-next-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: corgi: Convert to use GPIO descriptors
backlight: pwm_bl: Switch to full GPIO descriptor
|
|
This is required for wake on lan on i.MX6
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to wake from suspend by ethernet magic packets the GPC
must be used as intc does not have wakeup functionality.
But the FEC DT node currently uses interrupt-extended,
specificying intc, thus breaking WoL.
This problem is probably fallout from the stacked domain conversion
as intc used to chain to GPC.
So replace "interrupts-extended" by "interrupts" to use the default
parent which is GPC.
Fixes: b923ff6af0d5 ("ARM: imx6: convert GPC to stacked domains")
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO development for the v5.7 kernel cycle.
Core and userspace API:
- The userspace API KFIFOs have been imoproved with locks that do not
block interrupts. This makes us better at getting events to
userspace without blocking or disturbing new events arriving in the
same time. This was reviewed by the KFIFO maintainer Stefani. This
is a generic improvement which paves the road for similar
improvements in other subsystems.
- We provide a new ioctl() for monitoring changes in the line
information, such as when multiple clients are taking lines and
giving them back, possibly reconfiguring them in the process: we
can now monitor that and not get stuck with stale static
information.
- An example tool 'gpio-watch' is provided to showcase this
functionality.
- Timestamps for events are switched to ktime_get_ns() which is
monotonic. We previously had a 'realtime' stamp which could move
forward and *backward* in time, which probably would just cause
silent bugs and weird behaviour. In the long run we see two
relevant timestamps: ktime_get_ns() or the timestamp sometimes
provided by the GPIO hardware itself, if that exists.
- Device Tree overlay support for GPIO hogs. On systems that load
overlays, these overlays can now contain hogs, and will then be
respected.
- Handle pin control interaction with nonexisting pin ranges in the
GPIO library core instead of in the individual drivers.
New drivers:
- New driver for the Mellanox BlueField 2 GPIO controller.
Driver improvements:
- Introduce the BGPIOF_NO_SET_ON_INPUT flag to the generic MMIO GPIO
library and use this flag in the MT7621 driver.
- Texas Instruments OMAP CPU power management improvements, such as
blocking of idle on pending GPIO interrupts"
* tag 'gpio-v5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (59 commits)
Revert "gpio: eic-sprd: Use devm_platform_ioremap_resource()"
pinctrl: Unconditionally assign .request()/.free()
gpio: Unconditionally assign .request()/.free()
gpio: export of_pinctrl_get to modules
pinctrl: Define of_pinctrl_get() dummy for !PINCTRL
gpio: Rename variable in core APIs
gpio: Avoid using pin ranges with !PINCTRL
gpiolib: Remove unused gpio_chip parameter from gpio_set_bias()
gpiolib: Pass gpio_desc to gpio_set_config()
gpiolib: Introduce gpiod_set_config()
tools: gpio: Fix out-of-tree build regression
gpio: gpiolib: fix a doc warning
gpio: tegra186: Add Tegra194 pin ranges for GG.0 and GG.1
gpio: tegra186: Add support for pin ranges
gpio: Support GPIO controllers without pin-ranges
ARM: integrator: impd1: Use GPIO_LOOKUP() helper macro
gpio: brcmstb: support gpio-line-names property
tools: gpio: Fix typo in gpio-utils
tools: gpio-hammer: Apply scripts/Lindent and retain good changes
gpiolib: gpio_name_to_desc: factor out !name check
...
|
|
Pull dma-mapping updates from Christoph Hellwig:
- fix an integer overflow in the coherent pool (Kevin Grandemange)
- provide support for in-place uncached remapping and use that for
openrisc
- fix the arm coherent allocator to take the bus limit into account
* tag 'dma-mapping-5.7' of git://git.infradead.org/users/hch/dma-mapping:
ARM/dma-mapping: merge __dma_supported into arm_dma_supported
ARM/dma-mapping: take the bus limit into account in __dma_alloc
ARM/dma-mapping: remove get_coherent_dma_mask
openrisc: use the generic in-place uncached DMA allocator
dma-direct: provide a arch_dma_clear_uncached hook
dma-direct: make uncached_kernel_address more general
dma-direct: consolidate the error handling in dma_direct_alloc_pages
dma-direct: remove the cached_kernel_address hook
dma-coherent: fix integer overflow in the reserved-memory dma allocation
|
|
Pull ARM devicetree updates from Arnd Bergmann:
"Most of the commits are for additional hardware support and minor
fixes for existing machines for all the usual platforms: qcom,
amlogic, at91, gemini, mediatek, ti, socfpga, i.mx, layerscape,
uniphier, rockchip, exynos, ux500, mvebu, tegra, stm32, renesas,
sunxi, broadcom, omap, and versatile.
The conversion of binding files to machine-readable yaml format
continues, along with fixes found during the validation. Andre
Przywara takes over maintainership for the old Calxeda Highbank
platform and provides a number of updates.
The OMAP2+ platforms see a continued move from platform data into dts
files, for many devices that relied on a mix of auxiliary data in
addition to the DT description
A moderate number of new SoCs and machines are added, here is a full
list:
- Two new Qualcomm SoCs with their evaluation boards: Snapdragon 865
(SM8250) is the current high-end phone chip, and IPQ6018 is a new
WiFi-6 router chip.
- Mediatek MT8516 application processor SoC for voice assistants,
along with the "pumpkin" development board
- NXP i.MX8M Plus SoC, a variant of the popular i.MX8M, along with an
evaluation board.
- Kontron "sl28" board family based on NXP LS1028A
- Eleven variations of the new i.MX6 TechNexion Pico board, combining
the "dwarf", "hobbit", "nymph" and "pi" baseboards with i.MX6/i.MX7
SoM carriers
- Three additional variants of the Toradex Colibri board family, all
based on versions of the NXP i.MX7.
- The Pinebook Pro laptop based on Rockchip RK3399
- Samsung S7710 Galaxy Xcover 2, a 2013 vintage Android phone based
on the ST-Ericsson u8500 platform
- DH Electronics DHCOM SoM and PDK2 rev. 400 carrier based on
STMicroelectronics stm32mp157
- Renesas M3ULCB starter kit for R-Car M3-W+
- Hoperun HiHope development board with Renesas RZ/G2M
- Pine64 PineTab tablet and PinePhone phone, both based on Allwinner
A64
- Linutronix Testbox v2 for the Lamobo R1 router, based on Allwinner
A20
- PocketBook Touch Lux 3 ebook reader, based on Allwinner A13"
* tag 'arm-dt-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (520 commits)
ARM: dts: ux500: Fix missing node renames
arm64: dts: Revert "specify console via command line"
MAINTAINERS: Update Calxeda Highbank maintainership
arm: dts: calxeda: Group port-phys and sgpio-gpio items
arm: dts: calxeda: Fix interrupt grouping
arm: dts: calxeda: Provide UART clock
arm: dts: calxeda: Basic DT file fixes
arm64: dts: specify console via command line
ARM: dts: at91: sama5d27_wlsom1_ek: add USB device node
ARM: dts: gemini: Add thermal zone to DIR-685
ARM: dts: gemini: Rename IDE nodes
ARM: socfpga: arria10: Add ptp_ref clock to ethernet nodes
arm64: dts: ti: k3-j721e-mcu: add scm node and phy-gmii-sel nodes
arm64: dts: ti: k3-am65-mcu: add phy-gmii-sel node
arm64: dts: ti: k3-am65-mcu: Add DMA entries for ADC
arm64: dts: ti: k3-am65-main: Add DMA entries for main_spi0
arm64: dts: ti: k3-j721e-mcu-wakeup: Add DMA entries for ADC
arm64: dts: ti: k3-am65: Add clocks to dwc3 nodes
arm64: dts: meson-g12b-odroid-n2: add SPIFC controller node
arm64: dts: khadas-vim3: add SPIFC controller node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM defconfig updates from Arnd Bergmann:
"As usual, tons of new drivers and other options got merged and are now
enabled in the defconfig files, usually as loadable modules"
* tag 'arm-defconfig-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (45 commits)
ARM: omap2plus_defconfig: Update for moved and dropped options
ARM: omap2plus_defconfig: Enable ina2xx_adc as a loadable module
ARM: omap2plus_defconfig: Enable McPDM optional PMIC clock as modules
ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules
ARM: omap2plus_defconfig: Enable zram as loadable modules
ARM: omap2plus_defconfig: Enable simple-pm-bus
arm64: defconfig: Enable Qualcomm SDM845 audio configs
arm64: defconfig: Enable e1000 device
arm64: defconfig: Enable PHY devices used on QorIQ boards
arm64: defconfig: Enable RTC devices for QorIQ boards
arm64: defconfig: Enable flash device drivers for QorIQ boards
arm64: defconfig: Enable ARM Mali display driver
arm64: defconfig: Enable QorIQ GPIO driver
arm64: defconfig: Enable QorIQ IFC NAND controller driver
arm64: defconfig: Enable ARM SBSA watchdog driver
arm64: defconfig: Enable QorIQ cpufreq driver
arm64: defconfig: Enable NXP/FSL SPI controller drivers
arm64: defconfig: Enable ENETC Ethernet controller and FELIX switch
arm64: defconfig: Enable QorIQ DPAA2 drivers
arm64: defconfig: Enable QorIQ DPAA1 drivers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"These are the usual updates for SoC specific device drivers and
related subsystems that don't have their own top-level maintainers:
- ARM SCMI/SCPI updates to allow pluggable transport layers
- TEE subsystem cleanups
- A new driver for the Amlogic secure power domain controller
- Various driver updates for the NXP Layerscape DPAA2, NXP i.MX SCU
and TI OMAP2+ sysc drivers.
- Qualcomm SoC driver updates, including a new library module for
"protection domain" notifications
- Lots of smaller bugfixes and cleanups in other drivers"
* tag 'arm-drivers-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (70 commits)
soc: fsl: qe: fix sparse warnings for ucc_slow.c
soc: fsl: qe: ucc_slow: remove 0 assignment for kzalloc'ed structure
soc: fsl: qe: fix sparse warnings for ucc_fast.c
soc: fsl: qe: fix sparse warnings for qe_ic.c
soc: fsl: qe: fix sparse warnings for ucc.c
soc: fsl: qe: fix sparse warning for qe_common.c
soc: fsl: qe: fix sparse warnings for qe.c
soc: qcom: Fix QCOM_APR dependencies
soc: qcom: pdr: Avoid uninitialized use of found in pdr_indication_cb
soc: imx: drop COMPILE_TEST for IMX_SCU_SOC
firmware: imx: add COMPILE_TEST for IMX_SCU driver
soc: imx: gpc: fix power up sequencing
soc: imx: increase build coverage for imx8m soc driver
soc: qcom: apr: Add avs/audio tracking functionality
dt-bindings: soc: qcom: apr: Add protection domain bindings
soc: qcom: Introduce Protection Domain Restart helpers
devicetree: bindings: firmware: add ipq806x to qcom_scm
memory: tegra: Correct debugfs clk rate-range on Tegra124
memory: tegra: Correct debugfs clk rate-range on Tegra30
memory: tegra: Correct debugfs clk rate-range on Tegra20
...
|
|
Pull ARM SoC updates from Arnd Bergmann:
"The code changes are mostly for 32-bit platforms and include:
- Lots of updates for the Nvidia Tegra platform, including cpuidle,
pmc, and dt-binding changes
- Microchip at91 power management updates for the recently added
sam9x60 SoC
- Treewide setup_irq deprecation by afzal mohammed
- STMicroelectronics stm32 gains earlycon support
- Renesas platforms with Cortex-A9 can now use the global timer
- Some TI OMAP2+ platforms gain cpuidle support
- Various cleanups for the i.MX6 and Orion platforms, as well as
Kconfig files across all platforms"
* tag 'arm-soc-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (75 commits)
ARM: qcom: Add support for IPQ40xx
ARM: mmp: replace setup_irq() by request_irq()
ARM: cns3xxx: replace setup_irq() by request_irq()
ARM: spear: replace setup_irq() by request_irq()
ARM: ep93xx: Replace setup_irq() by request_irq()
ARM: iop32x: replace setup_irq() by request_irq()
arm: mach-dove: Mark dove_io_desc as __maybe_unused
ARM: orion: replace setup_irq() by request_irq()
ARM: debug: stm32: add UART early console support for STM32MP1
ARM: debug: stm32: add UART early console support for STM32H7
ARM: debug: stm32: add UART early console configuration for STM32F7
ARM: debug: stm32: add UART early console configuration for STM32F4
cpuidle: tegra: Disable CC6 state if LP2 unavailable
cpuidle: tegra: Squash Tegra114 driver into the common driver
cpuidle: tegra: Squash Tegra30 driver into the common driver
cpuidle: Refactor and move out NVIDIA Tegra20 driver into drivers/cpuidle
ARM: tegra: cpuidle: Remove unnecessary memory barrier
ARM: tegra: cpuidle: Make abort_flag atomic
ARM: tegra: cpuidle: Handle case where secondary CPU hangs on entering LP2
ARM: tegra: Make outer_disable() open-coded
...
|
|
Include originally "late" updates for OMAP and Qualcomm,
now that it's not late any more.
* arm/late: (122 commits)
ARM: OMAP2+: Drop legacy platform data for ti81xx edma
ARM: dts: Configure interconnect target module for ti816x edma
ARM: dts: Configure interconnect target module for dm814x tptc3
ARM: dts: Configure interconnect target module for dm814x tptc2
ARM: dts: Configure interconnect target module for dm814x tptc1
ARM: dts: Configure interconnect target module for dm814x tptc0
ARM: dts: Configure interconnect target module for dm814x tpcc
ARM: OMAP2+: Drop legacy platform data for dm814x cpsw
ARM: dts: Configure interconnect target module for dm814x cpsw
clk: ti: Fix dm814x clkctrl for ethernet
arm64: dts: qcom: sdm845-mtp: Relocate remoteproc firmware
arm64: dts: sdm845: add IPA information
arm64: dts: qcom: db845c: add analog audio support
arm64: dts: qcom: sdm845: add pinctrl nodes for quat i2s
arm64: dts: qcom: c630: Enable audio support
arm64: dts: qcom: sdm845: add apr nodes
arm64: dts: qcom: sdm845: add slimbus nodes
arm64: dts: qcom: sc7180: Update reg names for SDHC
arm64: dts: qcom: qcs404: Enable CQE support for eMMC
arm64: dts: msm8916: Add fastrpc node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc/other driver patches for 5.7-rc1.
Lots of things in here, and it's later than expected due to some
reverts to resolve some reported issues. All is now clean with no
reported problems in linux-next.
Included in here is:
- interconnect updates
- mei driver updates
- uio updates
- nvmem driver updates
- soundwire updates
- binderfs updates
- coresight updates
- habanalabs updates
- mhi new bus type and core
- extcon driver updates
- some Kconfig cleanups
- other small misc driver cleanups and updates
As mentioned, all have been in linux-next for a while, and with the
last two reverts, all is calm and good"
* tag 'char-misc-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (174 commits)
Revert "driver core: platform: Initialize dma_parms for platform devices"
Revert "amba: Initialize dma_parms for amba devices"
amba: Initialize dma_parms for amba devices
driver core: platform: Initialize dma_parms for platform devices
bus: mhi: core: Drop the references to mhi_dev in mhi_destroy_device()
bus: mhi: core: Initialize bhie field in mhi_cntrl for RDDM capture
bus: mhi: core: Add support for reading MHI info from device
misc: rtsx: set correct pcr_ops for rts522A
speakup: misc: Use dynamic minor numbers for speakup devices
mei: me: add cedar fork device ids
coresight: do not use the BIT() macro in the UAPI header
Documentation: provide IBM contacts for embargoed hardware
nvmem: core: remove nvmem_sysfs_get_groups()
nvmem: core: use is_bin_visible for permissions
nvmem: core: use device_register and device_unregister
nvmem: core: add root_only member to nvmem device struct
extcon: axp288: Add wakeup support
extcon: Mark extcon_get_edev_name() function as exported symbol
extcon: palmas: Hide error messages if gpio returns -EPROBE_DEFER
dt-bindings: extcon: usbc-cros-ec: convert extcon-usbc-cros-ec.txt to yaml format
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here are three SPDX patches for 5.7-rc1.
One fixes up the SPDX tag for a single driver, while the other two go
through the tree and add SPDX tags for all of the .gitignore files as
needed.
Nothing too complex, but you will get a merge conflict with your
current tree, that should be trivial to handle (one file modified by
two things, one file deleted.)
All three of these have been in linux-next for a while, with no
reported issues other than the merge conflict"
* tag 'spdx-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
ASoC: MT6660: make spdxcheck.py happy
.gitignore: add SPDX License Identifier
.gitignore: remove too obvious comments
|
|
Pull ARM updates from Russell King:
- replace setup_irq() with request_irq() for ebsa110, footbridge, rpc
- fix clang assembly error in kexec code
- remove .fixup section in boot stub
- decompressor / EFI cache flushing updates
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8966/1: rpc: replace setup_irq() by request_irq()
ARM: 8965/2: footbridge: replace setup_irq() by request_irq()
ARM: 8964/1: ebsa110: replace setup_irq() by request_irq()
ARM: 8962/1: kexec: drop invalid assembly argument
ARM: decompressor: switch to by-VA cache maintenance for v7 cores
ARM: decompressor: prepare cache_clean_flush for doing by-VA maintenance
ARM: decompressor: factor out routine to obtain the inflated image size
ARM: 8959/1: Remove unused .fixup section in boot stub
ARM: allow unwinder to unwind recursive functions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Unit test for overlays with GPIO hogs
- Improve dma-ranges parsing to handle dma-ranges with multiple entries
- Update dtc to upstream version v1.6.0-2-g87a656ae5ff9
- Improve overlay error reporting
- Device link support for power-domains and hwlocks bindings
- Add vendor prefixes for Beacon, Topwise, ENE, Dell, SG Micro, Elida,
PocketBook, Xiaomi, Linutronix, OzzMaker, Waveshare Electronics, and
ITE Tech
- Add deprecated Marvell vendor prefix 'mrvl'
- A bunch of binding conversions to DT schema continues. Of note, the
common serial and USB connector bindings are converted.
- Add more Arm CPU compatibles
- Drop Mark Rutland as DT maintainer :(
* tag 'devicetree-for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (106 commits)
MAINTAINERS: drop an old reference to stm32 pwm timers doc
MAINTAINERS: dt: update etnaviv file reference
dt-bindings: usb: dwc2: fix bindings for amlogic, meson-gxbb-usb
dt-bindings: uniphier-system-bus: fix warning in the example
dt-bindings: display: meson-vpu: fix indentation of reg-names' "items"
dt-bindings: iio: Fix adi, ltc2983 uint64-matrix schema constraints
dt-bindings: power: Fix example for power-domain
dt-bindings: arm: Add some constraints for PSCI nodes
of: some unittest overlays not untracked
of: gpio unittest kfree() wrong object
dt-bindings: phy: convert phy-rockchip-inno-usb2 bindings to yaml
dt-bindings: serial: sh-sci: Convert to json-schema
dt-bindings: serial: Document serialN aliases
dt-bindings: thermal: tsens: Set 'additionalProperties: false'
dt-bindings: thermal: tsens: Fix nvmem-cell-names schema
dt-bindings: vendor-prefixes: Add Beacon vendor prefix
dt-bindings: vendor-prefixes: Add Topwise
of: of_private.h: Replace zero-length array with flexible-array member
docs: dt: fix a broken reference to input.yaml
docs: dt: fix references to ap806-system-controller.txt
...
|
|
Pull SCSI updates from James Bottomley:
"This series has a huge amount of churn because it pulls in Mauro's doc
update changing all our txt files to rst ones.
Excluding that, we have the usual driver updates (qla2xxx, ufs, lpfc,
zfcp, ibmvfc, pm80xx, aacraid), a treewide update for scnprintf and
some other minor updates.
The major core change is Hannes moving functions out of the aacraid
driver and into the core"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (223 commits)
scsi: aic7xxx: aic97xx: Remove FreeBSD-specific code
scsi: ufs: Do not rely on prefetched data
scsi: dc395x: remove dc395x_bios_param
scsi: libiscsi: Fix error count for active session
scsi: hpsa: correct race condition in offload enabled
scsi: message: fusion: Replace zero-length array with flexible-array member
scsi: qedi: Add PCI shutdown handler support
scsi: qedi: Add MFW error recovery process
scsi: ufs: Enable block layer runtime PM for well-known logical units
scsi: ufs-qcom: Override devfreq parameters
scsi: ufshcd: Let vendor override devfreq parameters
scsi: ufshcd: Update the set frequency to devfreq
scsi: ufs: Resume ufs host before accessing ufs device
scsi: ufs-mediatek: customize the delay for enabling host
scsi: ufs: make HCE polling more compact to improve initialization latency
scsi: ufs: allow custom delay prior to host enabling
scsi: ufs-mediatek: use common delay function
scsi: ufs: introduce common and flexible delay function
scsi: ufs: use an enum for host capabilities
scsi: ufs: fix uninitialized tx_lanes in ufshcd_disable_tx_lcc()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core changes:
- Fix issue where write_cached_data() fails but write() still returns
success
- maps: sa1100-flash: Replace zero-length array with flexible-array
member
- phram: Fix a double free issue in error path
- Convert fallthrough comments into statements
- MAINTAINERS: Add the IRC channel to the MTD related subsystems
Raw NAND core changes:
- Add support for manufacturer specific suspend/resume operation
- Add support for manufacturer specific lock/unlock operation
- Replace zero-length array with flexible-array member
- Fix a typo ("manufecturer")
- Ensure nand_soft_waitrdy wait period is enough
Raw NAND controller driver changes:
- Brcmnand:
* Add support for flash-edu for dma transfers (+ bindings)
- Cadence:
* Reinit completion before executing a new command
* Change bad block marker size
* Fix the calculation of the avaialble OOB size
* Get meta data size from registers
- Qualcom:
* Use dma_request_chan() instead dma_request_slave_channel()
* Release resources on failure within qcom_nandc_alloc()
- Allwinner:
* Use dma_request_chan() instead dma_request_slave_channel()
- Marvell:
* Use dma_request_chan() instead dma_request_slave_channel()
* Release DMA channel on error
- Freescale:
* Use dma_request_chan() instead dma_request_slave_channel()
- Macronix:
* Add support for Macronix NAND randomizer (+ bindings)
- Ams-delta:
* Rename structures and functions to gpio_nand*
* Make the driver custom I/O ready
* Drop useless local variable
* Support custom driver initialisation
* Add module device tables
* Handle more GPIO pins as optional
* Make read pulses optional
* Don't hardcode read/write pulse widths
* Push inversion handling to gpiolib
* Enable OF partition info support
* Drop board specific partition info
* Use struct gpio_nand_platdata
* Write protect device during probe
- Ingenic:
* Use devm_platform_ioremap_resource()
* Add dependency on MIPS || COMPILE_TEST
- Denali:
* Deassert write protect pin
- ST:
* Use dma_request_chan() instead dma_request_slave_channel()
Raw NAND chip driver changes:
- Toshiba:
* Support reading the number of bitflips for BENAND (Built-in ECC NAND)
- Macronix:
* Add support for deep power down mode
* Add support for block protection
SPI-NAND core changes:
- Do not erase the block before writing a bad block marker
- Explicitly use MTD_OPS_RAW to write the bad block marker to OOB
- Stop using spinand->oobbuf for buffering bad block markers
- Rework detect procedure for different READ_ID operation
SPI-NAND driver changes:
- Toshiba:
* Support for new Kioxia Serial NAND
* Rename function name to change suffix and prefix (8Gbit)
* Add comment about Kioxia ID
- Micron:
* Add new Micron SPI NAND devices with multiple dies
* Add M70A series Micron SPI NAND devices
* identify SPI NAND device with Continuous Read mode
* Add new Micron SPI NAND devices
* Describe the SPI NAND device MT29F2G01ABAGD
* Generalize the OOB layout structure and function names
SPI NOR core changes:
- Move all the manufacturer specific quirks/code out of the core, to
make the core logic more readable and thus ease maintenance.
- Move the SFDP logic out of the core, it provides a better
separation between the SFDP parsing and core logic.
- Trim what is exposed in spi-nor.h. The SPI NOR controllers drivers
must not be able to use structures that are meant just for the SPI
NOR core.
- Use the spi-mem direct mapping API to let advanced controllers
optimize the read/write operations when they support direct
mapping.
- Add generic formula for the Status Register block protection
handling. It fixes some long standing locking limitations and eases
the addition of the 4bit block protection support.
- Add block protection support for flashes with 4 block protection
bits in the Status Register.
SPI NOR controller drivers changes:
- The mtk-quadspi driver is replaced by the new spi-mem spi-mtk-nor
driver.
- Merge tag 'mtk-mtd-spi-move' into spi-nor/next to avoid conflicts.
HyperBus changes:
- Print error msg when compatible is wrong or missing
- Move mapping of direct access window from core to individual
drivers"
* tag 'mtd/for-5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (103 commits)
mtd: Convert fallthrough comments into statements
mtd: rawnand: toshiba: Support reading the number of bitflips for BENAND (Built-in ECC NAND)
MAINTAINERS: Add the IRC channel to the MTD related subsystems
mtd: Fix issue where write_cached_data() fails but write() still returns success
mtd: maps: sa1100-flash: Replace zero-length array with flexible-array member
mtd: phram: fix a double free issue in error path
mtd: spinand: toshiba: Support for new Kioxia Serial NAND
mtd: spinand: toshiba: Rename function name to change suffix and prefix (8Gbit)
mtd: rawnand: macronix: Add support for deep power down mode
mtd: rawnand: Add support for manufacturer specific suspend/resume operation
mtd: spi-nor: Enable locking for n25q512ax3/n25q512a
mtd: spi-nor: Add SR 4bit block protection support
mtd: spi-nor: Add generic formula for SR block protection handling
mtd: spi-nor: Set all BP bits to one when lock_len == mtd->size
mtd: spi-nor: controllers: aspeed-smc: Replace zero-length array with flexible-array member
mtd: spi-nor: Clear WEL bit when erase or program errors occur
MAINTAINERS: update entry after SPI NOR controller move
mtd: spi-nor: Trim what is exposed in spi-nor.h
mtd: spi-nor: Drop the MFR definitions
mtd: spi-nor: Get rid of the now empty spi_nor_ids[] table
...
|
|
Pull kvm updates from Paolo Bonzini:
"ARM:
- GICv4.1 support
- 32bit host removal
PPC:
- secure (encrypted) using under the Protected Execution Framework
ultravisor
s390:
- allow disabling GISA (hardware interrupt injection) and protected
VMs/ultravisor support.
x86:
- New dirty bitmap flag that sets all bits in the bitmap when dirty
page logging is enabled; this is faster because it doesn't require
bulk modification of the page tables.
- Initial work on making nested SVM event injection more similar to
VMX, and less buggy.
- Various cleanups to MMU code (though the big ones and related
optimizations were delayed to 5.8). Instead of using cr3 in
function names which occasionally means eptp, KVM too has
standardized on "pgd".
- A large refactoring of CPUID features, which now use an array that
parallels the core x86_features.
- Some removal of pointer chasing from kvm_x86_ops, which will also
be switched to static calls as soon as they are available.
- New Tigerlake CPUID features.
- More bugfixes, optimizations and cleanups.
Generic:
- selftests: cleanups, new MMU notifier stress test, steal-time test
- CSV output for kvm_stat"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (277 commits)
x86/kvm: fix a missing-prototypes "vmread_error"
KVM: x86: Fix BUILD_BUG() in __cpuid_entry_get_reg() w/ CONFIG_UBSAN=y
KVM: VMX: Add a trampoline to fix VMREAD error handling
KVM: SVM: Annotate svm_x86_ops as __initdata
KVM: VMX: Annotate vmx_x86_ops as __initdata
KVM: x86: Drop __exit from kvm_x86_ops' hardware_unsetup()
KVM: x86: Copy kvm_x86_ops by value to eliminate layer of indirection
KVM: x86: Set kvm_x86_ops only after ->hardware_setup() completes
KVM: VMX: Configure runtime hooks using vmx_x86_ops
KVM: VMX: Move hardware_setup() definition below vmx_x86_ops
KVM: x86: Move init-only kvm_x86_ops to separate struct
KVM: Pass kvm_init()'s opaque param to additional arch funcs
s390/gmap: return proper error code on ksm unsharing
KVM: selftests: Fix cosmetic copy-paste error in vm_mem_region_move()
KVM: Fix out of range accesses to memslots
KVM: X86: Micro-optimize IPI fastpath delay
KVM: X86: Delay read msr data iff writes ICR MSR
KVM: PPC: Book3S HV: Add a capability for enabling secure guests
KVM: arm64: GICv4.1: Expose HW-based SGIs in debugfs
KVM: arm64: GICv4.1: Allow non-trapping WFI when using HW SGIs
...
|
|
Merge updates from Andrew Morton:
"A large amount of MM, plenty more to come.
Subsystems affected by this patch series:
- tools
- kthread
- kbuild
- scripts
- ocfs2
- vfs
- mm: slub, kmemleak, pagecache, gup, swap, memcg, pagemap, mremap,
sparsemem, kasan, pagealloc, vmscan, compaction, mempolicy,
hugetlbfs, hugetlb"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (155 commits)
include/linux/huge_mm.h: check PageTail in hpage_nr_pages even when !THP
mm/hugetlb: fix build failure with HUGETLB_PAGE but not HUGEBTLBFS
selftests/vm: fix map_hugetlb length used for testing read and write
mm/hugetlb: remove unnecessary memory fetch in PageHeadHuge()
mm/hugetlb.c: clean code by removing unnecessary initialization
hugetlb_cgroup: add hugetlb_cgroup reservation docs
hugetlb_cgroup: add hugetlb_cgroup reservation tests
hugetlb: support file_region coalescing again
hugetlb_cgroup: support noreserve mappings
hugetlb_cgroup: add accounting for shared mappings
hugetlb: disable region_add file_region coalescing
hugetlb_cgroup: add reservation accounting for private mappings
mm/hugetlb_cgroup: fix hugetlb_cgroup migration
hugetlb_cgroup: add interface for charge/uncharge hugetlb reservations
hugetlb_cgroup: add hugetlb_cgroup reservation counter
hugetlbfs: Use i_mmap_rwsem to address page fault/truncate race
hugetlbfs: use i_mmap_rwsem for more pmd sharing synchronization
mm/memblock.c: remove redundant assignment to variable max_addr
mm: mempolicy: require at least one nodeid for MPOL_PREFERRED
mm: mempolicy: use VM_BUG_ON_VMA in queue_pages_test_walk()
...
|
|
|
|
The idea comes from a discussion between Linus and Andrea [1].
Before this patch we only allow a page fault to retry once. We achieved
this by clearing the FAULT_FLAG_ALLOW_RETRY flag when doing
handle_mm_fault() the second time. This was majorly used to avoid
unexpected starvation of the system by looping over forever to handle the
page fault on a single page. However that should hardly happen, and after
all for each code path to return a VM_FAULT_RETRY we'll first wait for a
condition (during which time we should possibly yield the cpu) to happen
before VM_FAULT_RETRY is really returned.
This patch removes the restriction by keeping the FAULT_FLAG_ALLOW_RETRY
flag when we receive VM_FAULT_RETRY. It means that the page fault handler
now can retry the page fault for multiple times if necessary without the
need to generate another page fault event. Meanwhile we still keep the
FAULT_FLAG_TRIED flag so page fault handler can still identify whether a
page fault is the first attempt or not.
Then we'll have these combinations of fault flags (only considering
ALLOW_RETRY flag and TRIED flag):
- ALLOW_RETRY and !TRIED: this means the page fault allows to
retry, and this is the first try
- ALLOW_RETRY and TRIED: this means the page fault allows to
retry, and this is not the first try
- !ALLOW_RETRY and !TRIED: this means the page fault does not allow
to retry at all
- !ALLOW_RETRY and TRIED: this is forbidden and should never be used
In existing code we have multiple places that has taken special care of
the first condition above by checking against (fault_flags &
FAULT_FLAG_ALLOW_RETRY). This patch introduces a simple helper to detect
the first retry of a page fault by checking against both (fault_flags &
FAULT_FLAG_ALLOW_RETRY) and !(fault_flag & FAULT_FLAG_TRIED) because now
even the 2nd try will have the ALLOW_RETRY set, then use that helper in
all existing special paths. One example is in __lock_page_or_retry(), now
we'll drop the mmap_sem only in the first attempt of page fault and we'll
keep it in follow up retries, so old locking behavior will be retained.
This will be a nice enhancement for current code [2] at the same time a
supporting material for the future userfaultfd-writeprotect work, since in
that work there will always be an explicit userfault writeprotect retry
for protected pages, and if that cannot resolve the page fault (e.g., when
userfaultfd-writeprotect is used in conjunction with swapped pages) then
we'll possibly need a 3rd retry of the page fault. It might also benefit
other potential users who will have similar requirement like userfault
write-protection.
GUP code is not touched yet and will be covered in follow up patch.
Please read the thread below for more information.
[1] https://lore.kernel.org/lkml/20171102193644.GB22686@redhat.com/
[2] https://lore.kernel.org/lkml/20181230154648.GB9832@redhat.com/
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Suggested-by: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Brian Geffon <bgeffon@google.com>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Denis Plotnikov <dplotnikov@virtuozzo.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Kirill A . Shutemov" <kirill@shutemov.name>
Cc: Martin Cracauer <cracauer@cons.org>
Cc: Marty McFadden <mcfadden8@llnl.gov>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Maya Gokhale <gokhale2@llnl.gov>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Link: http://lkml.kernel.org/r/20200220160246.9790-1-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Although there're tons of arch-specific page fault handlers, most of them
are still sharing the same initial value of the page fault flags. Say,
merely all of the page fault handlers would allow the fault to be retried,
and they also allow the fault to respond to SIGKILL.
Let's define a default value for the fault flags to replace those initial
page fault flags that were copied over. With this, it'll be far easier to
introduce new fault flag that can be used by all the architectures instead
of touching all the archs.
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Brian Geffon <bgeffon@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: Denis Plotnikov <dplotnikov@virtuozzo.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Kirill A . Shutemov" <kirill@shutemov.name>
Cc: Martin Cracauer <cracauer@cons.org>
Cc: Marty McFadden <mcfadden8@llnl.gov>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Maya Gokhale <gokhale2@llnl.gov>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Link: http://lkml.kernel.org/r/20200220160238.9694-1-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For most architectures, we've got a quick path to detect fatal signal
after a handle_mm_fault(). Introduce a helper for that quick path.
It cleans the current codes a bit so we don't need to duplicate the same
check across archs. More importantly, this will be an unified place that
we handle the signal immediately right after an interrupted page fault, so
it'll be much easier for us if we want to change the behavior of handling
signals later on for all the archs.
Note that currently only part of the archs are using this new helper,
because some archs have their own way to handle signals. In the follow up
patches, we'll try to apply this helper to all the rest of archs.
Another note is that the "regs" parameter in the new helper is not used
yet. It'll be used very soon. Now we kept it in this patch only to avoid
touching all the archs again in the follow up patches.
[peterx@redhat.com: fix sparse warnings]
Link: http://lkml.kernel.org/r/20200311145921.GD479302@xz-x1
Signed-off-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Brian Geffon <bgeffon@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Bobby Powers <bobbypowers@gmail.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Denis Plotnikov <dplotnikov@virtuozzo.com>
Cc: "Dr . David Alan Gilbert" <dgilbert@redhat.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: "Kirill A . Shutemov" <kirill@shutemov.name>
Cc: Martin Cracauer <cracauer@cons.org>
Cc: Marty McFadden <mcfadden8@llnl.gov>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Maya Gokhale <gokhale2@llnl.gov>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Pavel Emelyanov <xemul@openvz.org>
Link: http://lkml.kernel.org/r/20200220155353.8676-4-peterx@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change a header to mandatory-y if both of the following are met:
[1] At least one architecture (except um) specifies it as generic-y in
arch/*/include/asm/Kbuild
[2] Every architecture (except um) either has its own implementation
(arch/*/include/asm/*.h) or specifies it as generic-y in
arch/*/include/asm/Kbuild
This commit was generated by the following shell script.
----------------------------------->8-----------------------------------
arches=$(cd arch; ls -1 | sed -e '/Kconfig/d' -e '/um/d')
tmpfile=$(mktemp)
grep "^mandatory-y +=" include/asm-generic/Kbuild > $tmpfile
find arch -path 'arch/*/include/asm/Kbuild' |
xargs sed -n 's/^generic-y += \(.*\)/\1/p' | sort -u |
while read header
do
mandatory=yes
for arch in $arches
do
if ! grep -q "generic-y += $header" arch/$arch/include/asm/Kbuild &&
! [ -f arch/$arch/include/asm/$header ]; then
mandatory=no
break
fi
done
if [ "$mandatory" = yes ]; then
echo "mandatory-y += $header" >> $tmpfile
for arch in $arches
do
sed -i "/generic-y += $header/d" arch/$arch/include/asm/Kbuild
done
fi
done
sed -i '/^mandatory-y +=/d' include/asm-generic/Kbuild
LANG=C sort $tmpfile >> include/asm-generic/Kbuild
----------------------------------->8-----------------------------------
One obvious benefit is the diff stat:
25 files changed, 52 insertions(+), 557 deletions(-)
It is tedious to list generic-y for each arch that needs it.
So, mandatory-y works like a fallback default (by just wrapping
asm-generic one) when arch does not have a specific header
implementation.
See the following commits:
def3f7cefe4e81c296090e1722a76551142c227c
a1b39bae16a62ce4aae02d958224f19316d98b24
It is tedious to convert headers one by one, so I processed by a shell
script.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Link: http://lkml.kernel.org/r/20200210175452.5030-1-masahiroy@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull drm updates from Dave Airlie:
"This is the main drm pull request for 5.7-rc1.
Highlights:
- i915 enables Tigerlake by default
- i915 and amdgpu have initial OLED backlight support
[ Jani Nikula pipes up and points out that we've had a bunch of
"initial support" code for a long time already, but only now
Lyude made it actually work on real world machines ]
- vmwgfx add support to enable OpenGL 4 userspace
- zero length arrays are mostly removed.
Detailed summary:
new driver:
- tidss: TI Keystone platform display subsystem
core:
- new drm device warn macros
- mode config valid for memory constrained devices
- bridge bus format negotation
- consolidated fake vblank event handling
- dma_alloc related cleanups
- drop get_crtc callback
- dp: DP1.4 EDID corruption test
- EDID CEA detailed timings improvements
- relicense some code to dual GPL2/MIT
- convert core vblank support to per-crtc support
- rework drm_global_mutex
- bridge rework to allow omap_dss custom driver removeal
- remove drm_fb_helper connector interrfaces
- zero-length array removal
scheduler:
- support for modifying the sched list
- revert job distribution optimization
- helper to pick least loaded scheduler
- race condition fix
mst:
- various fixes
- remove register_connector callback
i915:
- uapi to allows userspace specific CS ring buffer sizes
- Tigerlake enablement patches + Tigerlake enabled by default
- new sysfs entries for engine properties
- display/logging refactors
- eDP/DP fixes for DPCD
- Gen7 back to aliasing-ppgtt
- Gen8+ irq refactor
- Avoid globals
- GEM locking fixes and simplifications
- Ice Lake and Elkhart Lake fixes and workarounds
- Baytrail/Haswell instability fix
- GVT - VFIO edid better support
amdgpu:
- Rework VM update handling in preparation for HMM support
- drm load/unload removal fixups
- USB-C PD firmware updates
- HDCP srm support
- Navi/renoir PM watermark fixes
- OLED panel support
- Optimize debugging vram access
- Use BACO for runtime pm
- DC clock programming optimizations and fixes
- PSP fw loading sequence updates
- Drop DRIVER_USE_AGP
- Remove legacy drm load and unload callbacks
- ACP Kconfig fix
- Lots of fixes across the driver
amdkfd:
- runtime pm support
- more gfx config details in amdgpu
radeon:
- drop DRIVER_USE_AGP
vmwgfx:
- Disable DMA when SEV encryption in use
- Shader Model 5 support - needed for GL4 support
msm:
- DPU resource manager refactor
- dpu using atomic global state
mediatek:
- MT8183 DPI support
etnaviv:
- out-of-bounds read fix
- expose feature flags for GC400 STM32MP1 SoC
- runtime suspend entry fix
- dma32 zone fix
hisilicon:
- mode selection fixes
meson:
- YUV420 support
lima:
- add support for heap buffers
tinydrm:
- removal of owner field
- explicit DT dependency removal
- YAML schema conversion
tegra:
- misc cleanups
tidss:
- new driver
virtio:
- better batching of notifications to host
- memory handling reworked
- shmem + gpu context fixes
hibmc:
- add gamma_set support
- improve DPMS support
pl111:
- Integrator IM-PD1 support
sun4i:
- LVDS support for A20 + A33
- DSI panel handling improvements"
* tag 'drm-next-2020-04-01' of git://anongit.freedesktop.org/drm/drm: (1537 commits)
drm/i915/display: Fix mode private_flags comparison at atomic_check
drm/i915/gt: Stage the transfer of the virtual breadcrumb
drm/i915/gt: Select the deepest available parking mode for rc6
drm/i915: Avoid live-lock with i915_vma_parked()
drm/i915/gt: Treat idling as a RPS downclock event
drm/i915/gt: Cancel a hung context if already closed
drm/i915: Use explicit flag to mark unreachable intel_context
drm/amdgpu: don't try to reserve training bo for sriov (v2)
drm/amdgpu/smu11: add support for SMU AC/DC interrupts
drm/amdgpu/swSMU: handle manual AC/DC notifications
drm/amdgpu/swSMU: handle DC controlled by GPIO for navi1x
drm/amdgpu/swSMU: set AC/DC mode based on the current system state (v2)
drm/amdgpu/swSMU: correct the bootup power source for Navi1X (v2)
drm/amdgpu/swSMU: use the smu11 power source helper for navi1x
drm/amdgpu/smu11: add a helper to set the power source
drm/amd/swSMU: add callback to set AC/DC power source (v2)
drm/scheduler: fix rare NULL ptr race
drm/amdgpu: fix the coverage issue to clear ArcVPGRs
drm/amd/display: Fix pageflip event race condition for DCN.
drm/[radeon|amdgpu]: Remove HAINAN board from max_sclk override check
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Fix out-of-sync IVs in self-test for IPsec AEAD algorithms
Algorithms:
- Use formally verified implementation of x86/curve25519
Drivers:
- Enhance hwrng support in caam
- Use crypto_engine for skcipher/aead/rsa/hash in caam
- Add Xilinx AES driver
- Add uacce driver
- Register zip engine to uacce in hisilicon
- Add support for OCTEON TX CPT engine in marvell"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (162 commits)
crypto: af_alg - bool type cosmetics
crypto: arm[64]/poly1305 - add artifact to .gitignore files
crypto: caam - limit single JD RNG output to maximum of 16 bytes
crypto: caam - enable prediction resistance in HRWNG
bus: fsl-mc: add api to retrieve mc version
crypto: caam - invalidate entropy register during RNG initialization
crypto: caam - check if RNG job failed
crypto: caam - simplify RNG implementation
crypto: caam - drop global context pointer and init_done
crypto: caam - use struct hwrng's .init for initialization
crypto: caam - allocate RNG instantiation descriptor with GFP_DMA
crypto: ccree - remove duplicated include from cc_aead.c
crypto: chelsio - remove set but not used variable 'adap'
crypto: marvell - enable OcteonTX cpt options for build
crypto: marvell - add the Virtual Function driver for CPT
crypto: marvell - add support for OCTEON TX CPT engine
crypto: marvell - create common Kconfig and Makefile for Marvell
crypto: arm/neon - memzero_explicit aes-cbc key
crypto: bcm - Use scnprintf() for avoiding potential buffer overflow
crypto: atmel-i2c - Fix wakeup fail
...
|
|
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big set of TTY / Serial patches for 5.7-rc1
Lots of console fixups and reworking in here, serial core tweaks
(doesn't that ever get old, why are we still creating new serial
devices?), serial driver updates, line-protocol driver updates, and
some vt cleanups and fixes included in here as well.
All have been in linux-next with no reported issues"
* tag 'tty-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (161 commits)
serial: 8250: Optimize irq enable after console write
serial: 8250: Fix rs485 delay after console write
vt: vt_ioctl: fix use-after-free in vt_in_use()
vt: vt_ioctl: fix VT_DISALLOCATE freeing in-use virtual console
tty: serial: make SERIAL_SPRD depend on COMMON_CLK
tty: serial: fsl_lpuart: fix return value checking
tty: serial: fsl_lpuart: move dma_request_chan()
ARM: dts: tango4: Make /serial compatible with ns16550a
ARM: dts: mmp*: Make the serial ports compatible with xscale-uart
ARM: dts: mmp*: Fix serial port names
ARM: dts: mmp2-brownstone: Don't redeclare phandle references
ARM: dts: pxa*: Make the serial ports compatible with xscale-uart
ARM: dts: pxa*: Fix serial port names
ARM: dts: pxa*: Don't redeclare phandle references
serial: omap: drop unused dt-bindings header
serial: 8250: 8250_omap: Add DMA support for UARTs on K3 SoCs
serial: 8250: 8250_omap: Work around errata causing spurious IRQs with DMA
serial: 8250: 8250_omap: Extend driver data to pass FIFO trigger info
serial: 8250: 8250_omap: Move locking out from __dma_rx_do_complete()
serial: 8250: 8250_omap: Account for data in flight during DMA teardown
...
|
|
Add support for the Qualcomm IPQ40xx SoC in Kconfig.
Also add its appropriate textofs.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Tested-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
msm needed rc6, so I just went and merged release
(msm has been in drm-next outside of this tree)
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timekeeping and timer updates from Thomas Gleixner:
"Core:
- Consolidation of the vDSO build infrastructure to address the
difficulties of cross-builds for ARM64 compat vDSO libraries by
restricting the exposure of header content to the vDSO build.
This is achieved by splitting out header content into separate
headers. which contain only the minimaly required information which
is necessary to build the vDSO. These new headers are included from
the kernel headers and the vDSO specific files.
- Enhancements to the generic vDSO library allowing more fine grained
control over the compiled in code, further reducing architecture
specific storage and preparing for adopting the generic library by
PPC.
- Cleanup and consolidation of the exit related code in posix CPU
timers.
- Small cleanups and enhancements here and there
Drivers:
- The obligatory new drivers: Ingenic JZ47xx and X1000 TCU support
- Correct the clock rate of PIT64b global clock
- setup_irq() cleanup
- Preparation for PWM and suspend support for the TI DM timer
- Expand the fttmr010 driver to support ast2600 systems
- The usual small fixes, enhancements and cleanups all over the
place"
* tag 'timers-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (80 commits)
Revert "clocksource/drivers/timer-probe: Avoid creating dead devices"
vdso: Fix clocksource.h macro detection
um: Fix header inclusion
arm64: vdso32: Enable Clang Compilation
lib/vdso: Enable common headers
arm: vdso: Enable arm to use common headers
x86/vdso: Enable x86 to use common headers
mips: vdso: Enable mips to use common headers
arm64: vdso32: Include common headers in the vdso library
arm64: vdso: Include common headers in the vdso library
arm64: Introduce asm/vdso/processor.h
arm64: vdso32: Code clean up
linux/elfnote.h: Replace elf.h with UAPI equivalent
scripts: Fix the inclusion order in modpost
common: Introduce processor.h
linux/ktime.h: Extract common header for vDSO
linux/jiffies.h: Extract common header for vDSO
linux/time64.h: Extract common header for vDSO
linux/time32.h: Extract common header for vDSO
linux/time.h: Extract common header for vDSO
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull NOHZ update from Thomas Gleixner:
"Remove TIF_NOHZ from three architectures
These architectures use a static key to decide whether context
tracking needs to be invoked and the TIF_NOHZ flag just causes a
pointless slowpath execution for nothing"
* tag 'timers-nohz-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
arm64: Remove TIF_NOHZ
arm: Remove TIF_NOHZ
x86: Remove TIF_NOHZ
context-tracking: Introduce CONFIG_HAVE_TIF_NOHZ
x86/entry: Remove _TIF_NOHZ from _TIF_WORK_SYSCALL_ENTRY
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core SMP updates from Thomas Gleixner:
"CPU (hotplug) updates:
- Support for locked CSD objects in smp_call_function_single_async()
which allows to simplify callsites in the scheduler core and MIPS
- Treewide consolidation of CPU hotplug functions which ensures the
consistency between the sysfs interface and kernel state. The low
level functions cpu_up/down() are now confined to the core code and
not longer accessible from random code"
* tag 'smp-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
cpu/hotplug: Ignore pm_wakeup_pending() for disable_nonboot_cpus()
cpu/hotplug: Hide cpu_up/down()
cpu/hotplug: Move bringup of secondary CPUs out of smp_init()
torture: Replace cpu_up/down() with add/remove_cpu()
firmware: psci: Replace cpu_up/down() with add/remove_cpu()
xen/cpuhotplug: Replace cpu_up/down() with device_online/offline()
parisc: Replace cpu_up/down() with add/remove_cpu()
sparc: Replace cpu_up/down() with add/remove_cpu()
powerpc: Replace cpu_up/down() with add/remove_cpu()
x86/smp: Replace cpu_up/down() with add/remove_cpu()
arm64: hibernate: Use bringup_hibernate_cpu()
cpu/hotplug: Provide bringup_hibernate_cpu()
arm64: Use reboot_cpu instead of hardconding it to 0
arm64: Don't use disable_nonboot_cpus()
ARM: Use reboot_cpu instead of hardcoding it to 0
ARM: Don't use disable_nonboot_cpus()
ia64: Replace cpu_down() with smp_shutdown_nonboot_cpus()
cpu/hotplug: Create a new function to shutdown nonboot cpus
cpu/hotplug: Add new {add,remove}_cpu() functions
sched/core: Remove rq.hrtick_csd_pending
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early.
Most cleanup changes come through the various maintainer trees, so
the final removal of setup_irq() is postponed towards the end of
the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and
unsafe interrupt injection including a fixup of the offending
PCI/AER error injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside
of an actual interrupt, can cause inconsistent state on the
fragile x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place"
* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
unicore32: Replace setup_irq() by request_irq()
sh: Replace setup_irq() by request_irq()
hexagon: Replace setup_irq() by request_irq()
c6x: Replace setup_irq() by request_irq()
alpha: Replace setup_irq() by request_irq()
irqchip/gic-v4.1: Eagerly vmap vPEs
irqchip/gic-v4.1: Add VSGI property setup
irqchip/gic-v4.1: Add VSGI allocation/teardown
irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
irqchip/gic-v4.1: Add initial SGI configuration
irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
irqchip/stm32: Retrigger both in eoi and unmask callbacks
irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
irqchip/xilinx: Do not call irq_set_default_host()
irqchip/xilinx: Enable generic irq multi handler
irqchip/xilinx: Fill error code when irq domain registration fails
irqchip/xilinx: Add support for multiple instances
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle are:
- Various NUMA scheduling updates: harmonize the load-balancer and
NUMA placement logic to not work against each other. The intended
result is better locality, better utilization and fewer migrations.
- Introduce Thermal Pressure tracking and optimizations, to improve
task placement on thermally overloaded systems.
- Implement frequency invariant scheduler accounting on (some) x86
CPUs. This is done by observing and sampling the 'recent' CPU
frequency average at ~tick boundaries. The CPU provides this data
via the APERF/MPERF MSRs. This hopefully makes our capacity
estimates more precise and keeps tasks on the same CPU better even
if it might seem overloaded at a lower momentary frequency. (As
usual, turbo mode is a complication that we resolve by observing
the maximum frequency and renormalizing to it.)
- Add asymmetric CPU capacity wakeup scan to improve capacity
utilization on asymmetric topologies. (big.LITTLE systems)
- PSI fixes and optimizations.
- RT scheduling capacity awareness fixes & improvements.
- Optimize the CONFIG_RT_GROUP_SCHED constraints code.
- Misc fixes, cleanups and optimizations - see the changelog for
details"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (62 commits)
threads: Update PID limit comment according to futex UAPI change
sched/fair: Fix condition of avg_load calculation
sched/rt: cpupri_find: Trigger a full search as fallback
kthread: Do not preempt current task if it is going to call schedule()
sched/fair: Improve spreading of utilization
sched: Avoid scale real weight down to zero
psi: Move PF_MEMSTALL out of task->flags
MAINTAINERS: Add maintenance information for psi
psi: Optimize switching tasks inside shared cgroups
psi: Fix cpu.pressure for cpu.max and competing cgroups
sched/core: Distribute tasks within affinity masks
sched/fair: Fix enqueue_task_fair warning
thermal/cpu-cooling, sched/core: Move the arch_set_thermal_pressure() API to generic scheduler code
sched/rt: Remove unnecessary push for unfit tasks
sched/rt: Allow pulling unfitting task
sched/rt: Optimize cpupri_find() on non-heterogenous systems
sched/rt: Re-instate old behavior in select_task_rq_rt()
sched/rt: cpupri_find: Implement fallback mechanism for !fit case
sched/fair: Fix reordering of enqueue/dequeue_task_fair()
sched/fair: Fix runnable_avg for throttled cfs
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The main changes in this cycle were:
- Continued user-access cleanups in the futex code.
- percpu-rwsem rewrite that uses its own waitqueue and atomic_t
instead of an embedded rwsem. This addresses a couple of
weaknesses, but the primary motivation was complications on the -rt
kernel.
- Introduce raw lock nesting detection on lockdep
(CONFIG_PROVE_RAW_LOCK_NESTING=y), document the raw_lock vs. normal
lock differences. This too originates from -rt.
- Reuse lockdep zapped chain_hlocks entries, to conserve RAM
footprint on distro-ish kernels running into the "BUG:
MAX_LOCKDEP_CHAIN_HLOCKS too low!" depletion of the lockdep
chain-entries pool.
- Misc cleanups, smaller fixes and enhancements - see the changelog
for details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (55 commits)
fs/buffer: Make BH_Uptodate_Lock bit_spin_lock a regular spinlock_t
thermal/x86_pkg_temp: Make pkg_temp_lock a raw_spinlock_t
Documentation/locking/locktypes: Minor copy editor fixes
Documentation/locking/locktypes: Further clarifications and wordsmithing
m68knommu: Remove mm.h include from uaccess_no.h
x86: get rid of user_atomic_cmpxchg_inatomic()
generic arch_futex_atomic_op_inuser() doesn't need access_ok()
x86: don't reload after cmpxchg in unsafe_atomic_op2() loop
x86: convert arch_futex_atomic_op_inuser() to user_access_begin/user_access_end()
objtool: whitelist __sanitizer_cov_trace_switch()
[parisc, s390, sparc64] no need for access_ok() in futex handling
sh: no need of access_ok() in arch_futex_atomic_op_inuser()
futex: arch_futex_atomic_op_inuser() calling conventions change
completion: Use lockdep_assert_RT_in_threaded_ctx() in complete_all()
lockdep: Add posixtimer context tracing bits
lockdep: Annotate irq_work
lockdep: Add hrtimer context tracing bits
lockdep: Introduce wait-type checks
completion: Use simple wait queues
sched/swait: Prepare usage in completions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull EFI updates from Ingo Molnar:
"The EFI changes in this cycle are much larger than usual, for two
(positive) reasons:
- The GRUB project is showing signs of life again, resulting in the
introduction of the generic Linux/UEFI boot protocol, instead of
x86 specific hacks which are increasingly difficult to maintain.
There's hope that all future extensions will now go through that
boot protocol.
- Preparatory work for RISC-V EFI support.
The main changes are:
- Boot time GDT handling changes
- Simplify handling of EFI properties table on arm64
- Generic EFI stub cleanups, to improve command line handling, file
I/O, memory allocation, etc.
- Introduce a generic initrd loading method based on calling back
into the firmware, instead of relying on the x86 EFI handover
protocol or device tree.
- Introduce a mixed mode boot method that does not rely on the x86
EFI handover protocol either, and could potentially be adopted by
other architectures (if another one ever surfaces where one
execution mode is a superset of another)
- Clean up the contents of 'struct efi', and move out everything that
doesn't need to be stored there.
- Incorporate support for UEFI spec v2.8A changes that permit
firmware implementations to return EFI_UNSUPPORTED from UEFI
runtime services at OS runtime, and expose a mask of which ones are
supported or unsupported via a configuration table.
- Partial fix for the lack of by-VA cache maintenance in the
decompressor on 32-bit ARM.
- Changes to load device firmware from EFI boot service memory
regions
- Various documentation updates and minor code cleanups and fixes"
* 'efi-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
efi/libstub/arm: Fix spurious message that an initrd was loaded
efi/libstub/arm64: Avoid image_base value from efi_loaded_image
partitions/efi: Fix partition name parsing in GUID partition entry
efi/x86: Fix cast of image argument
efi/libstub/x86: Use ULONG_MAX as upper bound for all allocations
efi: Fix a mistype in comments mentioning efivar_entry_iter_begin()
efi/libstub: Avoid linking libstub/lib-ksyms.o into vmlinux
efi/x86: Preserve %ebx correctly in efi_set_virtual_address_map()
efi/x86: Ignore the memory attributes table on i386
efi/x86: Don't relocate the kernel unless necessary
efi/x86: Remove extra headroom for setup block
efi/x86: Add kernel preferred address to PE header
efi/x86: Decompress at start of PE image load address
x86/boot/compressed/32: Save the output address instead of recalculating it
efi/libstub/x86: Deal with exit() boot service returning
x86/boot: Use unsigned comparison for addresses
efi/x86: Avoid using code32_start
efi/x86: Make efi32_pe_entry() more readable
efi/x86: Respect 32-bit ABI in efi32_pe_entry()
efi/x86: Annotate the LOADED_IMAGE_PROTOCOL_GUID with SYM_DATA
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB / PHY updates from Greg KH:
"Here are the big set of USB and PHY driver patches for 5.7-rc1.
Nothing huge here, some new PHY drivers, loads of USB gadget fixes and
updates, xhci updates, usb-serial driver updates and new device ids,
and other minor things. Full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'usb-5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (239 commits)
USB: cdc-acm: restore capability check order
usb: cdns3: make signed 1 bit bitfields unsigned
usb: gadget: fsl: remove unused variable 'driver_desc'
usb: gadget: f_fs: Fix use after free issue as part of queue failure
usb: typec: Correct the documentation for typec_cable_put()
USB: serial: io_edgeport: fix slab-out-of-bounds read in edge_interrupt_callback
USB: serial: option: add Wistron Neweb D19Q1
USB: serial: option: add BroadMobi BM806U
USB: serial: option: add support for ASKEY WWHC050
usb: core: Add ACPI support for USB interface devices
driver core: platform: Reimplement devm_platform_ioremap_resource
usb: dwc2: convert to devm_platform_get_and_ioremap_resource
usb: host: hisilicon: convert to devm_platform_get_and_ioremap_resource
usb: host: xhci-plat: convert to devm_platform_get_and_ioremap_resource
drivers: provide devm_platform_get_and_ioremap_resource()
phy: qcom-qusb2: Add new overriding tuning parameters in QUSB2 V2 PHY
phy: qcom-qusb2: Add support for overriding tuning parameters in QUSB2 V2 PHY
dt-bindings: phy: qcom-qusb2: Add support for overriding Phy tuning parameters
phy: qcom-qusb2: Add generic QUSB2 V2 PHY support
dt-bindings: phy: qcom,qusb2: Add compatibles for QUSB2 V2 phy and SC7180
...
|
|
Pull block driver updates from Jens Axboe:
- floppy driver cleanup series from Willy
- NVMe updates and fixes (Various)
- null_blk trace improvements (Chaitanya)
- bcache fixes (Coly)
- md fixes (via Song)
- loop block size change optimizations (Martijn)
- scnprintf() use (Takashi)
* tag 'for-5.7/drivers-2020-03-29' of git://git.kernel.dk/linux-block: (81 commits)
null_blk: add trace in null_blk_zoned.c
null_blk: add tracepoint helpers for zoned mode
block: add a zone condition debug helper
nvme: cleanup namespace identifier reporting in nvme_init_ns_head
nvme: rename __nvme_find_ns_head to nvme_find_ns_head
nvme: refactor nvme_identify_ns_descs error handling
nvme-tcp: Add warning on state change failure at nvme_tcp_setup_ctrl
nvme-rdma: Add warning on state change failure at nvme_rdma_setup_ctrl
nvme: Fix controller creation races with teardown flow
nvme: Make nvme_uninit_ctrl symmetric to nvme_init_ctrl
nvme: Fix ctrl use-after-free during sysfs deletion
nvme-pci: Re-order nvme_pci_free_ctrl
nvme: Remove unused return code from nvme_delete_ctrl_sync
nvme: Use nvme_state_terminal helper
nvme: release ida resources
nvme: Add compat_ioctl handler for NVME_IOCTL_SUBMIT_IO
nvmet-tcp: optimize tcp stack TX when data digest is used
nvme-fabrics: Use scnprintf() for avoiding potential buffer overflow
nvme-multipath: do not reset on unknown status
nvmet-rdma: allocate RW ctxs according to mdts
...
|
|
Until now a PHY-fixup in mach-imx set our rgmii timing correctly. For
the PHY KSZ9131 there is no PHY-fixup in mach-imx. To support this PHY
too, use rgmii-id.
For the now used KSZ9031 nothing will change, as rgmii-id is only
implemented and supported by the KSZ9131.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .S_shipped yields a .S, and the pattern in these directories is to
add that to .gitignore so that git-status doesn't raise a fuss.
Fixes: a6b803b3ddc7 ("crypto: arm/poly1305 - incorporate OpenSSL/CRYPTOGAMS NEON implementation")
Fixes: f569ca164751 ("crypto: arm64/poly1305 - incorporate OpenSSL/CRYPTOGAMS NEON implementation")
Reported-by: Emil Renner Berthing <kernel@esmil.dk>
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs into locking/core
Pull uaccess futex cleanups for Al Viro:
Consolidate access_ok() usage and the futex uaccess function zoo.
|
