diff options
Diffstat (limited to 'drivers/tty/serial')
| -rw-r--r-- | drivers/tty/serial/8250/8250_core.c | 5 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_omap.c | 25 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_pci.c | 13 | ||||
| -rw-r--r-- | drivers/tty/serial/bcm63xx_uart.c | 7 | ||||
| -rw-r--r-- | drivers/tty/serial/imx.c | 4 | ||||
| -rw-r--r-- | drivers/tty/serial/mcf.c | 2 | ||||
| -rw-r--r-- | drivers/tty/serial/serial_base.h | 30 | ||||
| -rw-r--r-- | drivers/tty/serial/serial_base_bus.c | 129 | ||||
| -rw-r--r-- | drivers/tty/serial/serial_core.c | 4 |
9 files changed, 41 insertions, 178 deletions
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index ff15022369e4..b0adafc44747 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -15,7 +15,6 @@ */ #include <linux/acpi.h> -#include <linux/cleanup.h> #include <linux/module.h> #include <linux/moduleparam.h> #include <linux/ioport.h> @@ -42,8 +41,6 @@ #include <asm/irq.h> -#include "../serial_base.h" /* For serial_base_add_isa_preferred_console() */ - #include "8250.h" /* @@ -563,8 +560,6 @@ static void __init serial8250_isa_init_ports(void) port->irqflags |= irqflag; if (serial8250_isa_config != NULL) serial8250_isa_config(i, &up->port, &up->capabilities); - - serial_base_add_isa_preferred_console(serial8250_reg.dev_name, i); } } diff --git a/drivers/tty/serial/8250/8250_omap.c b/drivers/tty/serial/8250/8250_omap.c index 170639d12b2a..ddac0a13cf84 100644 --- a/drivers/tty/serial/8250/8250_omap.c +++ b/drivers/tty/serial/8250/8250_omap.c @@ -115,6 +115,10 @@ /* RX FIFO occupancy indicator */ #define UART_OMAP_RX_LVL 0x19 +/* Timeout low and High */ +#define UART_OMAP_TO_L 0x26 +#define UART_OMAP_TO_H 0x27 + /* * Copy of the genpd flags for the console. * Only used if console suspend is disabled @@ -663,13 +667,24 @@ static irqreturn_t omap8250_irq(int irq, void *dev_id) /* * On K3 SoCs, it is observed that RX TIMEOUT is signalled after - * FIFO has been drained, in which case a dummy read of RX FIFO - * is required to clear RX TIMEOUT condition. + * FIFO has been drained or erroneously. + * So apply solution of Errata i2310 as mentioned in + * https://www.ti.com/lit/pdf/sprz536 */ if (priv->habit & UART_RX_TIMEOUT_QUIRK && - (iir & UART_IIR_RX_TIMEOUT) == UART_IIR_RX_TIMEOUT && - serial_port_in(port, UART_OMAP_RX_LVL) == 0) { - serial_port_in(port, UART_RX); + (iir & UART_IIR_RX_TIMEOUT) == UART_IIR_RX_TIMEOUT) { + unsigned char efr2, timeout_h, timeout_l; + + efr2 = serial_in(up, UART_OMAP_EFR2); + timeout_h = serial_in(up, UART_OMAP_TO_H); + timeout_l = serial_in(up, UART_OMAP_TO_L); + serial_out(up, UART_OMAP_TO_H, 0xFF); + serial_out(up, UART_OMAP_TO_L, 0xFF); + serial_out(up, UART_OMAP_EFR2, UART_OMAP_EFR2_TIMEOUT_BEHAVE); + serial_in(up, UART_IIR); + serial_out(up, UART_OMAP_EFR2, efr2); + serial_out(up, UART_OMAP_TO_H, timeout_h); + serial_out(up, UART_OMAP_TO_L, timeout_l); } /* Stop processing interrupts on input overrun */ diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index 40af74b55933..e1d7aa2fa347 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -1985,6 +1985,17 @@ enum { MOXA_SUPP_RS485 = BIT(2), }; +static unsigned short moxa_get_nports(unsigned short device) +{ + switch (device) { + case PCI_DEVICE_ID_MOXA_CP116E_A_A: + case PCI_DEVICE_ID_MOXA_CP116E_A_B: + return 8; + } + + return FIELD_GET(0x00F0, device); +} + static bool pci_moxa_is_mini_pcie(unsigned short device) { if (device == PCI_DEVICE_ID_MOXA_CP102N || @@ -2038,7 +2049,7 @@ static int pci_moxa_init(struct pci_dev *dev) { unsigned short device = dev->device; resource_size_t iobar_addr = pci_resource_start(dev, 2); - unsigned int num_ports = (device & 0x00F0) >> 4, i; + unsigned int i, num_ports = moxa_get_nports(device); u8 val, init_mode = MOXA_RS232; if (!(pci_moxa_supported_rs(dev) & MOXA_SUPP_RS232)) { diff --git a/drivers/tty/serial/bcm63xx_uart.c b/drivers/tty/serial/bcm63xx_uart.c index 34801a6f300b..b88cc28c94e3 100644 --- a/drivers/tty/serial/bcm63xx_uart.c +++ b/drivers/tty/serial/bcm63xx_uart.c @@ -308,8 +308,8 @@ static void bcm_uart_do_tx(struct uart_port *port) val = bcm_uart_readl(port, UART_MCTL_REG); val = (val & UART_MCTL_TXFIFOFILL_MASK) >> UART_MCTL_TXFIFOFILL_SHIFT; - - pending = uart_port_tx_limited(port, ch, port->fifosize - val, + pending = uart_port_tx_limited_flags(port, ch, UART_TX_NOSTOP, + port->fifosize - val, true, bcm_uart_writel(port, ch, UART_FIFO_REG), ({})); @@ -320,6 +320,9 @@ static void bcm_uart_do_tx(struct uart_port *port) val = bcm_uart_readl(port, UART_IR_REG); val &= ~UART_TX_INT_MASK; bcm_uart_writel(port, val, UART_IR_REG); + + if (uart_tx_stopped(port)) + bcm_uart_stop_tx(port); } /* diff --git a/drivers/tty/serial/imx.c b/drivers/tty/serial/imx.c index 2eb22594960f..f4f40c9373c2 100644 --- a/drivers/tty/serial/imx.c +++ b/drivers/tty/serial/imx.c @@ -1952,8 +1952,10 @@ static int imx_uart_rs485_config(struct uart_port *port, struct ktermios *termio /* Make sure Rx is enabled in case Tx is active with Rx disabled */ if (!(rs485conf->flags & SER_RS485_ENABLED) || - rs485conf->flags & SER_RS485_RX_DURING_TX) + rs485conf->flags & SER_RS485_RX_DURING_TX) { + imx_uart_setup_ufcr(sport, TXTL_DEFAULT, RXTL_DEFAULT); imx_uart_start_rx(port); + } return 0; } diff --git a/drivers/tty/serial/mcf.c b/drivers/tty/serial/mcf.c index b0604d6da025..58858dd352c5 100644 --- a/drivers/tty/serial/mcf.c +++ b/drivers/tty/serial/mcf.c @@ -462,7 +462,7 @@ static const struct uart_ops mcf_uart_ops = { .verify_port = mcf_verify_port, }; -static struct mcf_uart mcf_ports[4]; +static struct mcf_uart mcf_ports[10]; #define MCF_MAXPORTS ARRAY_SIZE(mcf_ports) diff --git a/drivers/tty/serial/serial_base.h b/drivers/tty/serial/serial_base.h index 743a72ac34f3..b6c38d2edfd4 100644 --- a/drivers/tty/serial/serial_base.h +++ b/drivers/tty/serial/serial_base.h @@ -49,33 +49,3 @@ void serial_ctrl_unregister_port(struct uart_driver *drv, struct uart_port *port int serial_core_register_port(struct uart_driver *drv, struct uart_port *port); void serial_core_unregister_port(struct uart_driver *drv, struct uart_port *port); - -#ifdef CONFIG_SERIAL_CORE_CONSOLE - -int serial_base_add_preferred_console(struct uart_driver *drv, - struct uart_port *port); - -#else - -static inline -int serial_base_add_preferred_console(struct uart_driver *drv, - struct uart_port *port) -{ - return 0; -} - -#endif - -#ifdef CONFIG_SERIAL_8250_CONSOLE - -int serial_base_add_isa_preferred_console(const char *name, int idx); - -#else - -static inline -int serial_base_add_isa_preferred_console(const char *name, int idx) -{ - return 0; -} - -#endif diff --git a/drivers/tty/serial/serial_base_bus.c b/drivers/tty/serial/serial_base_bus.c index 73c6ee540c83..4df2a4b10445 100644 --- a/drivers/tty/serial/serial_base_bus.c +++ b/drivers/tty/serial/serial_base_bus.c @@ -8,7 +8,6 @@ * The serial core bus manages the serial core controller instances. */ -#include <linux/cleanup.h> #include <linux/container_of.h> #include <linux/device.h> #include <linux/idr.h> @@ -205,134 +204,6 @@ void serial_base_port_device_remove(struct serial_port_device *port_dev) put_device(&port_dev->dev); } -#ifdef CONFIG_SERIAL_CORE_CONSOLE - -static int serial_base_add_one_prefcon(const char *match, const char *dev_name, - int port_id) -{ - int ret; - - ret = add_preferred_console_match(match, dev_name, port_id); - if (ret == -ENOENT) - return 0; - - return ret; -} - -#ifdef __sparc__ - -/* Handle Sparc ttya and ttyb options as done in console_setup() */ -static int serial_base_add_sparc_console(const char *dev_name, int idx) -{ - const char *name; - - switch (idx) { - case 0: - name = "ttya"; - break; - case 1: - name = "ttyb"; - break; - default: - return 0; - } - - return serial_base_add_one_prefcon(name, dev_name, idx); -} - -#else - -static inline int serial_base_add_sparc_console(const char *dev_name, int idx) -{ - return 0; -} - -#endif - -static int serial_base_add_prefcon(const char *name, int idx) -{ - const char *char_match __free(kfree) = NULL; - const char *nmbr_match __free(kfree) = NULL; - int ret; - - /* Handle ttyS specific options */ - if (strstarts(name, "ttyS")) { - /* No name, just a number */ - nmbr_match = kasprintf(GFP_KERNEL, "%i", idx); - if (!nmbr_match) - return -ENODEV; - - ret = serial_base_add_one_prefcon(nmbr_match, name, idx); - if (ret) - return ret; - - /* Sparc ttya and ttyb */ - ret = serial_base_add_sparc_console(name, idx); - if (ret) - return ret; - } - - /* Handle the traditional character device name style console=ttyS0 */ - char_match = kasprintf(GFP_KERNEL, "%s%i", name, idx); - if (!char_match) - return -ENOMEM; - - return serial_base_add_one_prefcon(char_match, name, idx); -} - -/** - * serial_base_add_preferred_console - Adds a preferred console - * @drv: Serial port device driver - * @port: Serial port instance - * - * Tries to add a preferred console for a serial port if specified in the - * kernel command line. Supports both the traditional character device such - * as console=ttyS0, and a hardware addressing based console=DEVNAME:0.0 - * style name. - * - * Translates the kernel command line option using a hardware based addressing - * console=DEVNAME:0.0 to the serial port character device such as ttyS0. - * Cannot be called early for ISA ports, depends on struct device. - * - * Note that duplicates are ignored by add_preferred_console(). - * - * Return: 0 on success, negative error code on failure. - */ -int serial_base_add_preferred_console(struct uart_driver *drv, - struct uart_port *port) -{ - const char *port_match __free(kfree) = NULL; - int ret; - - ret = serial_base_add_prefcon(drv->dev_name, port->line); - if (ret) - return ret; - - port_match = kasprintf(GFP_KERNEL, "%s:%i.%i", dev_name(port->dev), - port->ctrl_id, port->port_id); - if (!port_match) - return -ENOMEM; - - /* Translate a hardware addressing style console=DEVNAME:0.0 */ - return serial_base_add_one_prefcon(port_match, drv->dev_name, port->line); -} - -#endif - -#ifdef CONFIG_SERIAL_8250_CONSOLE - -/* - * Early ISA ports initialize the console before there is no struct device. - * This should be only called from serial8250_isa_init_preferred_console(), - * other callers are likely wrong and should rely on earlycon instead. - */ -int serial_base_add_isa_preferred_console(const char *name, int idx) -{ - return serial_base_add_prefcon(name, idx); -} - -#endif - static int serial_base_init(void) { int ret; diff --git a/drivers/tty/serial/serial_core.c b/drivers/tty/serial/serial_core.c index 0c4d60976663..2a8006e3d687 100644 --- a/drivers/tty/serial/serial_core.c +++ b/drivers/tty/serial/serial_core.c @@ -3422,10 +3422,6 @@ int serial_core_register_port(struct uart_driver *drv, struct uart_port *port) if (ret) goto err_unregister_ctrl_dev; - ret = serial_base_add_preferred_console(drv, port); - if (ret) - goto err_unregister_port_dev; - ret = serial_core_add_one_port(drv, port); if (ret) goto err_unregister_port_dev; |