diff options
Diffstat (limited to 'drivers/phy/realtek/phy-rtk-usb3.c')
| -rw-r--r-- | drivers/phy/realtek/phy-rtk-usb3.c | 767 |
1 files changed, 767 insertions, 0 deletions
diff --git a/drivers/phy/realtek/phy-rtk-usb3.c b/drivers/phy/realtek/phy-rtk-usb3.c new file mode 100644 index 000000000000..7881f908aade --- /dev/null +++ b/drivers/phy/realtek/phy-rtk-usb3.c @@ -0,0 +1,767 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * phy-rtk-usb3.c RTK usb3.0 phy driver + * + * copyright (c) 2023 realtek semiconductor corporation + * + */ + +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/of_address.h> +#include <linux/uaccess.h> +#include <linux/debugfs.h> +#include <linux/nvmem-consumer.h> +#include <linux/regmap.h> +#include <linux/sys_soc.h> +#include <linux/mfd/syscon.h> +#include <linux/phy/phy.h> +#include <linux/usb.h> +#include <linux/usb/hcd.h> +#include <linux/usb/phy.h> + +#define USB_MDIO_CTRL_PHY_BUSY BIT(7) +#define USB_MDIO_CTRL_PHY_WRITE BIT(0) +#define USB_MDIO_CTRL_PHY_ADDR_SHIFT 8 +#define USB_MDIO_CTRL_PHY_DATA_SHIFT 16 + +#define MAX_USB_PHY_DATA_SIZE 0x30 +#define PHY_ADDR_0X09 0x09 +#define PHY_ADDR_0X0B 0x0b +#define PHY_ADDR_0X0D 0x0d +#define PHY_ADDR_0X10 0x10 +#define PHY_ADDR_0X1F 0x1f +#define PHY_ADDR_0X20 0x20 +#define PHY_ADDR_0X21 0x21 +#define PHY_ADDR_0X30 0x30 + +#define REG_0X09_FORCE_CALIBRATION BIT(9) +#define REG_0X0B_RX_OFFSET_RANGE_MASK 0xc +#define REG_0X0D_RX_DEBUG_TEST_EN BIT(6) +#define REG_0X10_DEBUG_MODE_SETTING 0x3c0 +#define REG_0X10_DEBUG_MODE_SETTING_MASK 0x3f8 +#define REG_0X1F_RX_OFFSET_CODE_MASK 0x1e + +#define USB_U3_TX_LFPS_SWING_TRIM_SHIFT 4 +#define USB_U3_TX_LFPS_SWING_TRIM_MASK 0xf +#define AMPLITUDE_CONTROL_COARSE_MASK 0xff +#define AMPLITUDE_CONTROL_FINE_MASK 0xffff +#define AMPLITUDE_CONTROL_COARSE_DEFAULT 0xff +#define AMPLITUDE_CONTROL_FINE_DEFAULT 0xffff + +#define PHY_ADDR_MAP_ARRAY_INDEX(addr) (addr) +#define ARRAY_INDEX_MAP_PHY_ADDR(index) (index) + +struct phy_reg { + void __iomem *reg_mdio_ctl; +}; + +struct phy_data { + u8 addr; + u16 data; +}; + +struct phy_cfg { + int param_size; + struct phy_data param[MAX_USB_PHY_DATA_SIZE]; + + bool check_efuse; + bool do_toggle; + bool do_toggle_once; + bool use_default_parameter; + bool check_rx_front_end_offset; +}; + +struct phy_parameter { + struct phy_reg phy_reg; + + /* Get from efuse */ + u8 efuse_usb_u3_tx_lfps_swing_trim; + + /* Get from dts */ + u32 amplitude_control_coarse; + u32 amplitude_control_fine; +}; + +struct rtk_phy { + struct usb_phy phy; + struct device *dev; + + struct phy_cfg *phy_cfg; + int num_phy; + struct phy_parameter *phy_parameter; + + struct dentry *debug_dir; +}; + +#define PHY_IO_TIMEOUT_USEC (50000) +#define PHY_IO_DELAY_US (100) + +static inline int utmi_wait_register(void __iomem *reg, u32 mask, u32 result) +{ + int ret; + unsigned int val; + + ret = read_poll_timeout(readl, val, ((val & mask) == result), + PHY_IO_DELAY_US, PHY_IO_TIMEOUT_USEC, false, reg); + if (ret) { + pr_err("%s can't program USB phy\n", __func__); + return -ETIMEDOUT; + } + + return 0; +} + +static int rtk_phy3_wait_vbusy(struct phy_reg *phy_reg) +{ + return utmi_wait_register(phy_reg->reg_mdio_ctl, USB_MDIO_CTRL_PHY_BUSY, 0); +} + +static u16 rtk_phy_read(struct phy_reg *phy_reg, char addr) +{ + unsigned int tmp; + u32 value; + + tmp = (addr << USB_MDIO_CTRL_PHY_ADDR_SHIFT); + + writel(tmp, phy_reg->reg_mdio_ctl); + + rtk_phy3_wait_vbusy(phy_reg); + + value = readl(phy_reg->reg_mdio_ctl); + value = value >> USB_MDIO_CTRL_PHY_DATA_SHIFT; + + return (u16)value; +} + +static int rtk_phy_write(struct phy_reg *phy_reg, char addr, u16 data) +{ + unsigned int val; + + val = USB_MDIO_CTRL_PHY_WRITE | + (addr << USB_MDIO_CTRL_PHY_ADDR_SHIFT) | + (data << USB_MDIO_CTRL_PHY_DATA_SHIFT); + + writel(val, phy_reg->reg_mdio_ctl); + + rtk_phy3_wait_vbusy(phy_reg); + + return 0; +} + +static void do_rtk_usb3_phy_toggle(struct rtk_phy *rtk_phy, int index, bool connect) +{ + struct phy_cfg *phy_cfg = rtk_phy->phy_cfg; + struct phy_reg *phy_reg; + struct phy_parameter *phy_parameter; + struct phy_data *phy_data; + u8 addr; + u16 data; + int i; + + phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index]; + phy_reg = &phy_parameter->phy_reg; + + if (!phy_cfg->do_toggle) + return; + + i = PHY_ADDR_MAP_ARRAY_INDEX(PHY_ADDR_0X09); + phy_data = phy_cfg->param + i; + addr = phy_data->addr; + data = phy_data->data; + + if (!addr && !data) { + addr = PHY_ADDR_0X09; + data = rtk_phy_read(phy_reg, addr); + phy_data->addr = addr; + phy_data->data = data; + } + + rtk_phy_write(phy_reg, addr, data & (~REG_0X09_FORCE_CALIBRATION)); + mdelay(1); + rtk_phy_write(phy_reg, addr, data | REG_0X09_FORCE_CALIBRATION); +} + +static int do_rtk_phy_init(struct rtk_phy *rtk_phy, int index) +{ + struct phy_cfg *phy_cfg; + struct phy_reg *phy_reg; + struct phy_parameter *phy_parameter; + int i = 0; + + phy_cfg = rtk_phy->phy_cfg; + phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index]; + phy_reg = &phy_parameter->phy_reg; + + if (phy_cfg->use_default_parameter) + goto do_toggle; + + for (i = 0; i < phy_cfg->param_size; i++) { + struct phy_data *phy_data = phy_cfg->param + i; + u8 addr = phy_data->addr; + u16 data = phy_data->data; + + if (!addr && !data) + continue; + + rtk_phy_write(phy_reg, addr, data); + } + +do_toggle: + if (phy_cfg->do_toggle_once) + phy_cfg->do_toggle = true; + + do_rtk_usb3_phy_toggle(rtk_phy, index, false); + + if (phy_cfg->do_toggle_once) { + u16 check_value = 0; + int count = 10; + u16 value_0x0d, value_0x10; + + /* Enable Debug mode by set 0x0D and 0x10 */ + value_0x0d = rtk_phy_read(phy_reg, PHY_ADDR_0X0D); + value_0x10 = rtk_phy_read(phy_reg, PHY_ADDR_0X10); + + rtk_phy_write(phy_reg, PHY_ADDR_0X0D, + value_0x0d | REG_0X0D_RX_DEBUG_TEST_EN); + rtk_phy_write(phy_reg, PHY_ADDR_0X10, + (value_0x10 & ~REG_0X10_DEBUG_MODE_SETTING_MASK) | + REG_0X10_DEBUG_MODE_SETTING); + + check_value = rtk_phy_read(phy_reg, PHY_ADDR_0X30); + + while (!(check_value & BIT(15))) { + check_value = rtk_phy_read(phy_reg, PHY_ADDR_0X30); + mdelay(1); + if (count-- < 0) + break; + } + + if (!(check_value & BIT(15))) + dev_info(rtk_phy->dev, "toggle fail addr=0x%02x, data=0x%04x\n", + PHY_ADDR_0X30, check_value); + + /* Disable Debug mode by set 0x0D and 0x10 to default*/ + rtk_phy_write(phy_reg, PHY_ADDR_0X0D, value_0x0d); + rtk_phy_write(phy_reg, PHY_ADDR_0X10, value_0x10); + + phy_cfg->do_toggle = false; + } + + if (phy_cfg->check_rx_front_end_offset) { + u16 rx_offset_code, rx_offset_range; + u16 code_mask = REG_0X1F_RX_OFFSET_CODE_MASK; + u16 range_mask = REG_0X0B_RX_OFFSET_RANGE_MASK; + bool do_update = false; + + rx_offset_code = rtk_phy_read(phy_reg, PHY_ADDR_0X1F); + if (((rx_offset_code & code_mask) == 0x0) || + ((rx_offset_code & code_mask) == code_mask)) + do_update = true; + + rx_offset_range = rtk_phy_read(phy_reg, PHY_ADDR_0X0B); + if (((rx_offset_range & range_mask) == range_mask) && do_update) { + dev_warn(rtk_phy->dev, "Don't update rx_offset_range (rx_offset_code=0x%x, rx_offset_range=0x%x)\n", + rx_offset_code, rx_offset_range); + do_update = false; + } + + if (do_update) { + u16 tmp1, tmp2; + + tmp1 = rx_offset_range & (~range_mask); + tmp2 = rx_offset_range & range_mask; + tmp2 += (1 << 2); + rx_offset_range = tmp1 | (tmp2 & range_mask); + rtk_phy_write(phy_reg, PHY_ADDR_0X0B, rx_offset_range); + goto do_toggle; + } + } + + return 0; +} + +static int rtk_phy_init(struct phy *phy) +{ + struct rtk_phy *rtk_phy = phy_get_drvdata(phy); + int ret = 0; + int i; + unsigned long phy_init_time = jiffies; + + for (i = 0; i < rtk_phy->num_phy; i++) + ret = do_rtk_phy_init(rtk_phy, i); + + dev_dbg(rtk_phy->dev, "Initialized RTK USB 3.0 PHY (take %dms)\n", + jiffies_to_msecs(jiffies - phy_init_time)); + + return ret; +} + +static int rtk_phy_exit(struct phy *phy) +{ + return 0; +} + +static const struct phy_ops ops = { + .init = rtk_phy_init, + .exit = rtk_phy_exit, + .owner = THIS_MODULE, +}; + +static void rtk_phy_toggle(struct usb_phy *usb3_phy, bool connect, int port) +{ + int index = port; + struct rtk_phy *rtk_phy = NULL; + + rtk_phy = dev_get_drvdata(usb3_phy->dev); + + if (index > rtk_phy->num_phy) { + dev_err(rtk_phy->dev, "%s: The port=%d is not in usb phy (num_phy=%d)\n", + __func__, index, rtk_phy->num_phy); + return; + } + + do_rtk_usb3_phy_toggle(rtk_phy, index, connect); +} + +static int rtk_phy_notify_port_status(struct usb_phy *x, int port, + u16 portstatus, u16 portchange) +{ + bool connect = false; + + pr_debug("%s port=%d portstatus=0x%x portchange=0x%x\n", + __func__, port, (int)portstatus, (int)portchange); + if (portstatus & USB_PORT_STAT_CONNECTION) + connect = true; + + if (portchange & USB_PORT_STAT_C_CONNECTION) + rtk_phy_toggle(x, connect, port); + + return 0; +} + +#ifdef CONFIG_DEBUG_FS +static struct dentry *create_phy_debug_root(void) +{ + struct dentry *phy_debug_root; + + phy_debug_root = debugfs_lookup("phy", usb_debug_root); + if (!phy_debug_root) + phy_debug_root = debugfs_create_dir("phy", usb_debug_root); + + return phy_debug_root; +} + +static int rtk_usb3_parameter_show(struct seq_file *s, void *unused) +{ + struct rtk_phy *rtk_phy = s->private; + struct phy_cfg *phy_cfg; + int i, index; + + phy_cfg = rtk_phy->phy_cfg; + + seq_puts(s, "Property:\n"); + seq_printf(s, " check_efuse: %s\n", + phy_cfg->check_efuse ? "Enable" : "Disable"); + seq_printf(s, " do_toggle: %s\n", + phy_cfg->do_toggle ? "Enable" : "Disable"); + seq_printf(s, " do_toggle_once: %s\n", + phy_cfg->do_toggle_once ? "Enable" : "Disable"); + seq_printf(s, " use_default_parameter: %s\n", + phy_cfg->use_default_parameter ? "Enable" : "Disable"); + + for (index = 0; index < rtk_phy->num_phy; index++) { + struct phy_reg *phy_reg; + struct phy_parameter *phy_parameter; + + phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index]; + phy_reg = &phy_parameter->phy_reg; + + seq_printf(s, "PHY %d:\n", index); + + for (i = 0; i < phy_cfg->param_size; i++) { + struct phy_data *phy_data = phy_cfg->param + i; + u8 addr = ARRAY_INDEX_MAP_PHY_ADDR(i); + u16 data = phy_data->data; + + if (!phy_data->addr && !data) + seq_printf(s, " addr = 0x%02x, data = none ==> read value = 0x%04x\n", + addr, rtk_phy_read(phy_reg, addr)); + else + seq_printf(s, " addr = 0x%02x, data = 0x%04x ==> read value = 0x%04x\n", + addr, data, rtk_phy_read(phy_reg, addr)); + } + + seq_puts(s, "PHY Property:\n"); + seq_printf(s, " efuse_usb_u3_tx_lfps_swing_trim: 0x%x\n", + (int)phy_parameter->efuse_usb_u3_tx_lfps_swing_trim); + seq_printf(s, " amplitude_control_coarse: 0x%x\n", + (int)phy_parameter->amplitude_control_coarse); + seq_printf(s, " amplitude_control_fine: 0x%x\n", + (int)phy_parameter->amplitude_control_fine); + } + + return 0; +} +DEFINE_SHOW_ATTRIBUTE(rtk_usb3_parameter); + +static inline void create_debug_files(struct rtk_phy *rtk_phy) +{ + struct dentry *phy_debug_root = NULL; + + phy_debug_root = create_phy_debug_root(); + + if (!phy_debug_root) + return; + + rtk_phy->debug_dir = debugfs_create_dir(dev_name(rtk_phy->dev), phy_debug_root); + if (!rtk_phy->debug_dir) + return; + + if (!debugfs_create_file("parameter", 0444, rtk_phy->debug_dir, rtk_phy, + &rtk_usb3_parameter_fops)) + goto file_error; + + return; + +file_error: + debugfs_remove_recursive(rtk_phy->debug_dir); +} + +static inline void remove_debug_files(struct rtk_phy *rtk_phy) +{ + debugfs_remove_recursive(rtk_phy->debug_dir); +} +#else +static inline void create_debug_files(struct rtk_phy *rtk_phy) { } +static inline void remove_debug_files(struct rtk_phy *rtk_phy) { } +#endif /* CONFIG_DEBUG_FS */ + +static int get_phy_data_by_efuse(struct rtk_phy *rtk_phy, + struct phy_parameter *phy_parameter, int index) +{ + struct phy_cfg *phy_cfg = rtk_phy->phy_cfg; + u8 value = 0; + struct nvmem_cell *cell; + + if (!phy_cfg->check_efuse) + goto out; + + cell = nvmem_cell_get(rtk_phy->dev, "usb_u3_tx_lfps_swing_trim"); + if (IS_ERR(cell)) { + dev_dbg(rtk_phy->dev, "%s no usb_u3_tx_lfps_swing_trim: %ld\n", + __func__, PTR_ERR(cell)); + } else { + unsigned char *buf; + size_t buf_size; + + buf = nvmem_cell_read(cell, &buf_size); + if (!IS_ERR(buf)) { + value = buf[0] & USB_U3_TX_LFPS_SWING_TRIM_MASK; + kfree(buf); + } + nvmem_cell_put(cell); + } + + if (value > 0 && value < 0x8) + phy_parameter->efuse_usb_u3_tx_lfps_swing_trim = 0x8; + else + phy_parameter->efuse_usb_u3_tx_lfps_swing_trim = (u8)value; + +out: + return 0; +} + +static void update_amplitude_control_value(struct rtk_phy *rtk_phy, + struct phy_parameter *phy_parameter) +{ + struct phy_cfg *phy_cfg; + struct phy_reg *phy_reg; + + phy_reg = &phy_parameter->phy_reg; + phy_cfg = rtk_phy->phy_cfg; + + if (phy_parameter->amplitude_control_coarse != AMPLITUDE_CONTROL_COARSE_DEFAULT) { + u16 val_mask = AMPLITUDE_CONTROL_COARSE_MASK; + u16 data; + + if (!phy_cfg->param[PHY_ADDR_0X20].addr && !phy_cfg->param[PHY_ADDR_0X20].data) { + phy_cfg->param[PHY_ADDR_0X20].addr = PHY_ADDR_0X20; + data = rtk_phy_read(phy_reg, PHY_ADDR_0X20); + } else { + data = phy_cfg->param[PHY_ADDR_0X20].data; + } + + data &= (~val_mask); + data |= (phy_parameter->amplitude_control_coarse & val_mask); + + phy_cfg->param[PHY_ADDR_0X20].data = data; + } + + if (phy_parameter->efuse_usb_u3_tx_lfps_swing_trim) { + u8 efuse_val = phy_parameter->efuse_usb_u3_tx_lfps_swing_trim; + u16 val_mask = USB_U3_TX_LFPS_SWING_TRIM_MASK; + int val_shift = USB_U3_TX_LFPS_SWING_TRIM_SHIFT; + u16 data; + + if (!phy_cfg->param[PHY_ADDR_0X20].addr && !phy_cfg->param[PHY_ADDR_0X20].data) { + phy_cfg->param[PHY_ADDR_0X20].addr = PHY_ADDR_0X20; + data = rtk_phy_read(phy_reg, PHY_ADDR_0X20); + } else { + data = phy_cfg->param[PHY_ADDR_0X20].data; + } + + data &= ~(val_mask << val_shift); + data |= ((efuse_val & val_mask) << val_shift); + + phy_cfg->param[PHY_ADDR_0X20].data = data; + } + + if (phy_parameter->amplitude_control_fine != AMPLITUDE_CONTROL_FINE_DEFAULT) { + u16 val_mask = AMPLITUDE_CONTROL_FINE_MASK; + + if (!phy_cfg->param[PHY_ADDR_0X21].addr && !phy_cfg->param[PHY_ADDR_0X21].data) + phy_cfg->param[PHY_ADDR_0X21].addr = PHY_ADDR_0X21; + + phy_cfg->param[PHY_ADDR_0X21].data = + phy_parameter->amplitude_control_fine & val_mask; + } +} + +static int parse_phy_data(struct rtk_phy *rtk_phy) +{ + struct device *dev = rtk_phy->dev; + struct phy_parameter *phy_parameter; + int ret = 0; + int index; + + rtk_phy->phy_parameter = devm_kzalloc(dev, sizeof(struct phy_parameter) * + rtk_phy->num_phy, GFP_KERNEL); + if (!rtk_phy->phy_parameter) + return -ENOMEM; + + for (index = 0; index < rtk_phy->num_phy; index++) { + phy_parameter = &((struct phy_parameter *)rtk_phy->phy_parameter)[index]; + + phy_parameter->phy_reg.reg_mdio_ctl = of_iomap(dev->of_node, 0) + index; + + /* Amplitude control address 0x20 bit 0 to bit 7 */ + if (of_property_read_u32(dev->of_node, "realtek,amplitude-control-coarse-tuning", + &phy_parameter->amplitude_control_coarse)) + phy_parameter->amplitude_control_coarse = AMPLITUDE_CONTROL_COARSE_DEFAULT; + + /* Amplitude control address 0x21 bit 0 to bit 16 */ + if (of_property_read_u32(dev->of_node, "realtek,amplitude-control-fine-tuning", + &phy_parameter->amplitude_control_fine)) + phy_parameter->amplitude_control_fine = AMPLITUDE_CONTROL_FINE_DEFAULT; + + get_phy_data_by_efuse(rtk_phy, phy_parameter, index); + + update_amplitude_control_value(rtk_phy, phy_parameter); + } + + return ret; +} + +static int rtk_usb3phy_probe(struct platform_device *pdev) +{ + struct rtk_phy *rtk_phy; + struct device *dev = &pdev->dev; + struct phy *generic_phy; + struct phy_provider *phy_provider; + const struct phy_cfg *phy_cfg; + int ret; + + phy_cfg = of_device_get_match_data(dev); + if (!phy_cfg) { + dev_err(dev, "phy config are not assigned!\n"); + return -EINVAL; + } + + rtk_phy = devm_kzalloc(dev, sizeof(*rtk_phy), GFP_KERNEL); + if (!rtk_phy) + return -ENOMEM; + + rtk_phy->dev = &pdev->dev; + rtk_phy->phy.dev = rtk_phy->dev; + rtk_phy->phy.label = "rtk-usb3phy"; + rtk_phy->phy.notify_port_status = rtk_phy_notify_port_status; + + rtk_phy->phy_cfg = devm_kzalloc(dev, sizeof(*phy_cfg), GFP_KERNEL); + + memcpy(rtk_phy->phy_cfg, phy_cfg, sizeof(*phy_cfg)); + + rtk_phy->num_phy = 1; + + ret = parse_phy_data(rtk_phy); + if (ret) + goto err; + + platform_set_drvdata(pdev, rtk_phy); + + generic_phy = devm_phy_create(rtk_phy->dev, NULL, &ops); + if (IS_ERR(generic_phy)) + return PTR_ERR(generic_phy); + + phy_set_drvdata(generic_phy, rtk_phy); + + phy_provider = devm_of_phy_provider_register(rtk_phy->dev, of_phy_simple_xlate); + if (IS_ERR(phy_provider)) + return PTR_ERR(phy_provider); + + ret = usb_add_phy_dev(&rtk_phy->phy); + if (ret) + goto err; + + create_debug_files(rtk_phy); + +err: + return ret; +} + +static void rtk_usb3phy_remove(struct platform_device *pdev) +{ + struct rtk_phy *rtk_phy = platform_get_drvdata(pdev); + + remove_debug_files(rtk_phy); + + usb_remove_phy(&rtk_phy->phy); +} + +static const struct phy_cfg rtd1295_phy_cfg = { + .param_size = MAX_USB_PHY_DATA_SIZE, + .param = { [0] = {0x01, 0x4008}, [1] = {0x01, 0xe046}, + [2] = {0x02, 0x6046}, [3] = {0x03, 0x2779}, + [4] = {0x04, 0x72f5}, [5] = {0x05, 0x2ad3}, + [6] = {0x06, 0x000e}, [7] = {0x07, 0x2e00}, + [8] = {0x08, 0x3591}, [9] = {0x09, 0x525c}, + [10] = {0x0a, 0xa600}, [11] = {0x0b, 0xa904}, + [12] = {0x0c, 0xc000}, [13] = {0x0d, 0xef1c}, + [14] = {0x0e, 0x2000}, [15] = {0x0f, 0x0000}, + [16] = {0x10, 0x000c}, [17] = {0x11, 0x4c00}, + [18] = {0x12, 0xfc00}, [19] = {0x13, 0x0c81}, + [20] = {0x14, 0xde01}, [21] = {0x15, 0x0000}, + [22] = {0x16, 0x0000}, [23] = {0x17, 0x0000}, + [24] = {0x18, 0x0000}, [25] = {0x19, 0x4004}, + [26] = {0x1a, 0x1260}, [27] = {0x1b, 0xff00}, + [28] = {0x1c, 0xcb00}, [29] = {0x1d, 0xa03f}, + [30] = {0x1e, 0xc2e0}, [31] = {0x1f, 0x2807}, + [32] = {0x20, 0x947a}, [33] = {0x21, 0x88aa}, + [34] = {0x22, 0x0057}, [35] = {0x23, 0xab66}, + [36] = {0x24, 0x0800}, [37] = {0x25, 0x0000}, + [38] = {0x26, 0x040a}, [39] = {0x27, 0x01d6}, + [40] = {0x28, 0xf8c2}, [41] = {0x29, 0x3080}, + [42] = {0x2a, 0x3082}, [43] = {0x2b, 0x2078}, + [44] = {0x2c, 0xffff}, [45] = {0x2d, 0xffff}, + [46] = {0x2e, 0x0000}, [47] = {0x2f, 0x0040}, }, + .check_efuse = false, + .do_toggle = true, + .do_toggle_once = false, + .use_default_parameter = false, + .check_rx_front_end_offset = false, +}; + +static const struct phy_cfg rtd1619_phy_cfg = { + .param_size = MAX_USB_PHY_DATA_SIZE, + .param = { [8] = {0x08, 0x3591}, + [38] = {0x26, 0x840b}, + [40] = {0x28, 0xf842}, }, + .check_efuse = false, + .do_toggle = true, + .do_toggle_once = false, + .use_default_parameter = false, + .check_rx_front_end_offset = false, +}; + +static const struct phy_cfg rtd1319_phy_cfg = { + .param_size = MAX_USB_PHY_DATA_SIZE, + .param = { [1] = {0x01, 0xac86}, + [6] = {0x06, 0x0003}, + [9] = {0x09, 0x924c}, + [10] = {0x0a, 0xa608}, + [11] = {0x0b, 0xb905}, + [14] = {0x0e, 0x2010}, + [32] = {0x20, 0x705a}, + [33] = {0x21, 0xf645}, + [34] = {0x22, 0x0013}, + [35] = {0x23, 0xcb66}, + [41] = {0x29, 0xff00}, }, + .check_efuse = true, + .do_toggle = true, + .do_toggle_once = false, + .use_default_parameter = false, + .check_rx_front_end_offset = false, +}; + +static const struct phy_cfg rtd1619b_phy_cfg = { + .param_size = MAX_USB_PHY_DATA_SIZE, + .param = { [1] = {0x01, 0xac8c}, + [6] = {0x06, 0x0017}, + [9] = {0x09, 0x724c}, + [10] = {0x0a, 0xb610}, + [11] = {0x0b, 0xb90d}, + [13] = {0x0d, 0xef2a}, + [15] = {0x0f, 0x9050}, + [16] = {0x10, 0x000c}, + [32] = {0x20, 0x70ff}, + [34] = {0x22, 0x0013}, + [35] = {0x23, 0xdb66}, + [38] = {0x26, 0x8609}, + [41] = {0x29, 0xff13}, + [42] = {0x2a, 0x3070}, }, + .check_efuse = true, + .do_toggle = false, + .do_toggle_once = true, + .use_default_parameter = false, + .check_rx_front_end_offset = false, +}; + +static const struct phy_cfg rtd1319d_phy_cfg = { + .param_size = MAX_USB_PHY_DATA_SIZE, + .param = { [1] = {0x01, 0xac89}, + [4] = {0x04, 0xf2f5}, + [6] = {0x06, 0x0017}, + [9] = {0x09, 0x424c}, + [10] = {0x0a, 0x9610}, + [11] = {0x0b, 0x9901}, + [12] = {0x0c, 0xf000}, + [13] = {0x0d, 0xef2a}, + [14] = {0x0e, 0x1000}, + [15] = {0x0f, 0x9050}, + [32] = {0x20, 0x7077}, + [35] = {0x23, 0x0b62}, + [37] = {0x25, 0x10ec}, + [42] = {0x2a, 0x3070}, }, + .check_efuse = true, + .do_toggle = false, + .do_toggle_once = true, + .use_default_parameter = false, + .check_rx_front_end_offset = true, +}; + +static const struct of_device_id usbphy_rtk_dt_match[] = { + { .compatible = "realtek,rtd1295-usb3phy", .data = &rtd1295_phy_cfg }, + { .compatible = "realtek,rtd1319-usb3phy", .data = &rtd1319_phy_cfg }, + { .compatible = "realtek,rtd1319d-usb3phy", .data = &rtd1319d_phy_cfg }, + { .compatible = "realtek,rtd1619-usb3phy", .data = &rtd1619_phy_cfg }, + { .compatible = "realtek,rtd1619b-usb3phy", .data = &rtd1619b_phy_cfg }, + {}, +}; +MODULE_DEVICE_TABLE(of, usbphy_rtk_dt_match); + +static struct platform_driver rtk_usb3phy_driver = { + .probe = rtk_usb3phy_probe, + .remove_new = rtk_usb3phy_remove, + .driver = { + .name = "rtk-usb3phy", + .of_match_table = usbphy_rtk_dt_match, + }, +}; + +module_platform_driver(rtk_usb3phy_driver); + +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform: rtk-usb3phy"); +MODULE_AUTHOR("Stanley Chang <stanley_chang@realtek.com>"); +MODULE_DESCRIPTION("Realtek usb 3.0 phy driver"); |