1 files changed, 0 insertions, 119 deletions
diff --git a/Documentation/devicetree/bindings/net/fsl-enetc.txt b/Documentation/devicetree/bindings/net/fsl-enetc.txt
deleted file mode 100644
index 9b9a3f197e2d..000000000000
--- a/Documentation/devicetree/bindings/net/fsl-enetc.txt
+++ /dev/null
@@ -1,119 +0,0 @@
-* ENETC ethernet device tree bindings
-
-Depending on board design and ENETC port type (internal or
-external) there are two supported link modes specified by
-below device tree bindings.
-
-Required properties:
-
-- reg		: Specifies PCIe Device Number and Function
-		  Number of the ENETC endpoint device, according
-		  to parent node bindings.
-- compatible	: Should be "fsl,enetc".
-
-1. The ENETC external port is connected to a MDIO configurable phy
-
-1.1. Using the local ENETC Port MDIO interface
-
-In this case, the ENETC node should include a "mdio" sub-node
-that in turn should contain the "ethernet-phy" node describing the
-external phy.  Below properties are required, their bindings
-already defined in Documentation/devicetree/bindings/net/ethernet.txt or
-Documentation/devicetree/bindings/net/phy.txt.
-
-Required:
-
-- phy-handle		: Phandle to a PHY on the MDIO bus.
-			  Defined in ethernet.txt.
-
-- phy-connection-type	: Defined in ethernet.txt.
-
-- mdio			: "mdio" node, defined in mdio.txt.
-
-- ethernet-phy		: "ethernet-phy" node, defined in phy.txt.
-
-Example:
-
-	ethernet@0,0 {
-		compatible = "fsl,enetc";
-		reg = <0x000000 0 0 0 0>;
-		phy-handle = <&sgmii_phy0>;
-		phy-connection-type = "sgmii";
-
-		mdio {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			sgmii_phy0: ethernet-phy@2 {
-				reg = <0x2>;
-			};
-		};
-	};
-
-1.2. Using the central MDIO PCIe endpoint device
-
-In this case, the mdio node should be defined as another PCIe
-endpoint node, at the same level with the ENETC port nodes.
-
-Required properties:
-
-- reg		: Specifies PCIe Device Number and Function
-		  Number of the ENETC endpoint device, according
-		  to parent node bindings.
-- compatible	: Should be "fsl,enetc-mdio".
-
-The remaining required mdio bus properties are standard, their bindings
-already defined in Documentation/devicetree/bindings/net/mdio.txt.
-
-Example:
-
-	ethernet@0,0 {
-		compatible = "fsl,enetc";
-		reg = <0x000000 0 0 0 0>;
-		phy-handle = <&sgmii_phy0>;
-		phy-connection-type = "sgmii";
-	};
-
-	mdio@0,3 {
-		compatible = "fsl,enetc-mdio";
-		reg = <0x000300 0 0 0 0>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		sgmii_phy0: ethernet-phy@2 {
-			reg = <0x2>;
-		};
-	};
-
-2. The ENETC port is an internal port or has a fixed-link external
-connection
-
-In this case, the ENETC port node defines a fixed link connection,
-as specified by Documentation/devicetree/bindings/net/fixed-link.txt.
-
-Required:
-
-- fixed-link	: "fixed-link" node, defined in "fixed-link.txt".
-
-Example:
-	ethernet@0,2 {
-		compatible = "fsl,enetc";
-		reg = <0x000200 0 0 0 0>;
-		fixed-link {
-			speed = <1000>;
-			full-duplex;
-		};
-	};
-
-* Integrated Endpoint Register Block bindings
-
-Optionally, the fsl_enetc driver can probe on the Integrated Endpoint Register
-Block, which preconfigures the FIFO limits for the ENETC ports. This is a node
-with the following properties:
-
-- reg		: Specifies the address in the SoC memory space.
-- compatible	: Must be "fsl,ls1028a-enetc-ierb".
-
-Example:
-	ierb@1f0800000 {
-		compatible = "fsl,ls1028a-enetc-ierb";
-		reg = <0x01 0xf0800000 0x0 0x10000>;
-	};