ath10k: Use bdf calibration variant for snoc targets

Board Data File (BDF) is loaded upon driver boot-up procedure.
The right board data file is identified using bus and qmi-board-id.

The problem, however, can occur when the (default) board data
file cannot fulfill with the vendor requirements and it is
necessary to use a different board data file.

Also using the chip_id for identifying the board data helps
in dealing with different variants of the board data file based
on the RF card. If the chip_id is not programmed, a default value
of 0xff will be used for parsing the board data file.

Add the support to get the variant field from DTSI and
use this information along with the chip_id to load the vendor
specific BDF.

The device tree requires addition strings to define the variant name

    wifi@a000000 {
            status = "okay";
            qcom,ath10k-calibration-variant = "xyz-v2";
    };

    wifi@a800000 {
            status = "okay";
            qcom,ath10k-calibration-variant = "xyz-v1";
    };

This would create the boarddata identifiers for the board-2.bin search

 *  bus=snoc,qmi-board-id=16,qmi-chip-id=0,variant=xyz-v1
 *  bus=snoc,qmi-board-id=17,qmi-chip-id=0,variant=xyz-v2

Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1

Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600157948-2042-1-git-send-email-pillair@codeaurora.org

1 files changed, 8 insertions, 0 deletions

diff --git a/drivers/net/wireless/ath/ath10k/qmi.c b/drivers/net/wireless/ath/ath10k/qmi.c
index 5468a41e928e..ae6b1f402adf 100644
--- a/drivers/net/wireless/ath/ath10k/qmi.c
+++ b/drivers/net/wireless/ath/ath10k/qmi.c
@@ -576,6 +576,8 @@ static int ath10k_qmi_cap_send_sync_msg(struct ath10k_qmi *qmi)
 	if (resp->chip_info_valid) {
 		qmi->chip_info.chip_id = resp->chip_info.chip_id;
 		qmi->chip_info.chip_family = resp->chip_info.chip_family;
+	} else {
+		qmi->chip_info.chip_id = 0xFF;
 	}
 
 	if (resp->board_info_valid)
@@ -817,12 +819,18 @@ err_setup_msa:
 static int ath10k_qmi_fetch_board_file(struct ath10k_qmi *qmi)
 {
 	struct ath10k *ar = qmi->ar;
+	int ret;
 
 	ar->hif.bus = ATH10K_BUS_SNOC;
 	ar->id.qmi_ids_valid = true;
 	ar->id.qmi_board_id = qmi->board_info.board_id;
+	ar->id.qmi_chip_id = qmi->chip_info.chip_id;
 	ar->hw_params.fw.dir = WCN3990_HW_1_0_FW_DIR;
 
+	ret = ath10k_core_check_dt(ar);
+	if (ret)
+		ath10k_dbg(ar, ATH10K_DBG_QMI, "DT bdf variant name not set.\n");
+
 	return ath10k_core_fetch_board_file(qmi->ar, ATH10K_BD_IE_BOARD);
 }