mmc: sdio: fix runtime PM anomalies by introducing MMC_CAP_POWER_OFF_CARD

Some board/card/host configurations are not capable of powering off the
card after boot.

To support such configurations, and to allow smoother transition to
runtime PM behavior, MMC_CAP_POWER_OFF_CARD is added, so hosts need to
explicitly indicate whether it's OK to power off their cards after boot.

SDIO core will enable runtime PM for a card only if that cap is set.
As a result, the card will be powered down after boot, and will only
be powered up again when a driver is loaded (and then it's up to the
driver to decide whether power will be kept or not).

This will prevent sdio_bus_probe() failures with setups that do not
support powering off the card.

Reported-and-tested-by: Daniel Drake <dsd@laptop.org>
Reported-and-tested-by: Arnd Hannemann <arnd@arndnet.de>
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>

1 files changed, 22 insertions, 11 deletions

diff --git a/drivers/mmc/core/sdio_bus.c b/drivers/mmc/core/sdio_bus.c
index 2716c7ab6bbf..203da443e339 100644
--- a/drivers/mmc/core/sdio_bus.c
+++ b/drivers/mmc/core/sdio_bus.c
@@ -17,6 +17,7 @@
 #include <linux/pm_runtime.h>
 
 #include <linux/mmc/card.h>
+#include <linux/mmc/host.h>
 #include <linux/mmc/sdio_func.h>
 
 #include "sdio_cis.h"
@@ -132,9 +133,11 @@ static int sdio_bus_probe(struct device *dev)
 	 * it should call pm_runtime_put_noidle() in its probe routine and
 	 * pm_runtime_get_noresume() in its remove routine.
 	 */
-	ret = pm_runtime_get_sync(dev);
-	if (ret < 0)
-		goto out;
+	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD) {
+		ret = pm_runtime_get_sync(dev);
+		if (ret < 0)
+			goto out;
+	}
 
 	/* Set the default block size so the driver is sure it's something
 	 * sensible. */
@@ -151,7 +154,8 @@ static int sdio_bus_probe(struct device *dev)
 	return 0;
 
 disable_runtimepm:
-	pm_runtime_put_noidle(dev);
+	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD)
+		pm_runtime_put_noidle(dev);
 out:
 	return ret;
 }
@@ -160,12 +164,14 @@ static int sdio_bus_remove(struct device *dev)
 {
 	struct sdio_driver *drv = to_sdio_driver(dev->driver);
 	struct sdio_func *func = dev_to_sdio_func(dev);
-	int ret;
+	int ret = 0;
 
 	/* Make sure card is powered before invoking ->remove() */
-	ret = pm_runtime_get_sync(dev);
-	if (ret < 0)
-		goto out;
+	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD) {
+		ret = pm_runtime_get_sync(dev);
+		if (ret < 0)
+			goto out;
+	}
 
 	drv->remove(func);
 
@@ -178,10 +184,12 @@ static int sdio_bus_remove(struct device *dev)
 	}
 
 	/* First, undo the increment made directly above */
-	pm_runtime_put_noidle(dev);
+	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD)
+		pm_runtime_put_noidle(dev);
 
 	/* Then undo the runtime PM settings in sdio_bus_probe() */
-	pm_runtime_put_noidle(dev);
+	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD)
+		pm_runtime_put_noidle(dev);
 
 out:
 	return ret;
@@ -191,6 +199,8 @@ out:
 
 static int sdio_bus_pm_prepare(struct device *dev)
 {
+	struct sdio_func *func = dev_to_sdio_func(dev);
+
 	/*
 	 * Resume an SDIO device which was suspended at run time at this
 	 * point, in order to allow standard SDIO suspend/resume paths
@@ -212,7 +222,8 @@ static int sdio_bus_pm_prepare(struct device *dev)
 	 * since there is little point in failing system suspend if a
 	 * device can't be resumed.
 	 */
-	pm_runtime_resume(dev);
+	if (func->card->host->caps & MMC_CAP_POWER_OFF_CARD)
+		pm_runtime_resume(dev);
 
 	return 0;
 }