Merge tag 'mmc-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc

Pull MMC updates from Ulf Hansson:
 "MMC host:
   - Convert from using tasklet to the BH workqueue
   - dw_mmc-bluefield: Add support for eMMC HW reset
   - mmc_spi: Allow spi controllers incapable of lower than 400kHz
   - sdhci: Rework code to eliminate SDHCI_QUIRK_UNSTABLE_RO_DETECT
   - sdhci-brcmstb: Add support for the BCM2712 variant
   - sdhci-esdhc-imx: Disable card-detect as system wakeup on S32G platforms
   - sdhci-msm: Add support for the SDX75 variant
   - sdhci-of-dwcmshc: Enable CQE support for some Rockchip variants
   - sdhci-of-esdhc: Convert DT-bindings to yaml
   - sdhci-sprd: Convert DT-bindings to yaml

  MEMSTICK:
   - rtsx_pci_ms: Remove the unused Realtek PCI memstick driver"

* tag 'mmc-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (26 commits)
  MAINTAINERS: add 's32@nxp.com' as relevant mailing list for 'sdhci-esdhc-imx' driver
  mmc: sdhci-esdhc-imx: obtain the 'per' clock rate after its enablement
  mmc: sdhci-esdhc-imx: disable card detect wake for S32G based platforms
  dt-bindings: mmc: sdhci-sprd: convert to YAML
  mmc: davinci_mmc: report all possible bus widths
  mmc: dw_mmc-bluefield: Add support for eMMC HW reset
  mmc: dw_mmc: Add support for platform specific eMMC HW reset
  mmc: sdhci_am654: Constify struct regmap_config
  mmc: Convert from tasklet to BH workqueue
  mmc: sdhi: Convert from tasklet to BH workqueue
  mmc: mmc_spi: allow for spi controllers incapable of getting as low as 400k
  memstick: rtsx_pci_ms: Remove Realtek PCI memstick driver
  MAINTAINERS: drop entry for VIA SD/MMC controller
  mmc: tmio: Remove obsolete .set_pwr() callback()
  mfd: tmio: Remove obsolete .set_clk_div() callback
  mmc: sdhci-brcmstb: Add ARCH_BCM2835 option
  mmc: sdhci: Eliminate SDHCI_QUIRK_UNSTABLE_RO_DETECT
  dt-bindings: mmc: Convert fsl-esdhc.txt to yaml
  dt-bindings: mmc: mmc-spi-slot: Change voltage-ranges to uint32-matrix
  mmc: add missing MODULE_DESCRIPTION() macros
  ...

9 files changed, 237 insertions, 126 deletions

diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm2835.yaml b/Documentation/devicetree/bindings/arm/bcm/bcm2835.yaml
index 162a39dab218..e4ff71f006b8 100644
--- a/Documentation/devicetree/bindings/arm/bcm/bcm2835.yaml
+++ b/Documentation/devicetree/bindings/arm/bcm/bcm2835.yaml
@@ -23,6 +23,12 @@ properties:
               - raspberrypi,4-model-b
           - const: brcm,bcm2711
 
+      - description: BCM2712 based Boards
+        items:
+          - enum:
+              - raspberrypi,5-model-b
+          - const: brcm,bcm2712
+
       - description: BCM2835 based Boards
         items:
           - enum:
diff --git a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx-mmc.yaml b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx-mmc.yaml
index bc403ae9e5d9..57646575a13f 100644
--- a/Documentation/devicetree/bindings/mmc/amlogic,meson-gx-mmc.yaml
+++ b/Documentation/devicetree/bindings/mmc/amlogic,meson-gx-mmc.yaml
@@ -51,6 +51,9 @@ properties:
       set when controller's internal DMA engine cannot access the DRAM memory,
       like on the G12A dedicated SDIO controller.
 
+  power-domains:
+    maxItems: 1
+
 required:
   - compatible
   - reg
diff --git a/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml
index cbd3d6c6c77f..eee6be7a7867 100644
--- a/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml
+++ b/Documentation/devicetree/bindings/mmc/brcm,sdhci-brcmstb.yaml
@@ -20,6 +20,7 @@ properties:
           - const: brcm,sdhci-brcmstb
       - items:
           - enum:
+              - brcm,bcm2712-sdhci
               - brcm,bcm74165b0-sdhci
               - brcm,bcm7445-sdhci
               - brcm,bcm7425-sdhci
diff --git a/Documentation/devicetree/bindings/mmc/fsl,esdhc.yaml b/Documentation/devicetree/bindings/mmc/fsl,esdhc.yaml
new file mode 100644
index 000000000000..b86ffb53b18b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/fsl,esdhc.yaml
@@ -0,0 +1,105 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/fsl,esdhc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale Enhanced Secure Digital Host Controller (eSDHC)
+
+description:
+  The Enhanced Secure Digital Host Controller provides an interface
+  for MMC, SD, and SDIO types of memory cards.
+
+maintainers:
+  - Frank Li <Frank.Li@nxp.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - fsl,mpc8536-esdhc
+          - fsl,mpc8378-esdhc
+          - fsl,p2020-esdhc
+          - fsl,p4080-esdhc
+          - fsl,t1040-esdhc
+          - fsl,t4240-esdhc
+          - fsl,ls1012a-esdhc
+          - fsl,ls1028a-esdhc
+          - fsl,ls1088a-esdhc
+          - fsl,ls1043a-esdhc
+          - fsl,ls1046a-esdhc
+          - fsl,ls2080a-esdhc
+      - const: fsl,esdhc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-frequency:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: specifies eSDHC base clock frequency.
+
+  sdhci,wp-inverted:
+    $ref: /schemas/types.yaml#/definitions/flag
+    deprecated: true
+    description:
+      specifies that eSDHC controller reports
+      inverted write-protect state; New devices should use the generic
+      "wp-inverted" property.
+
+  sdhci,1-bit-only:
+    $ref: /schemas/types.yaml#/definitions/flag
+    deprecated: true
+    description:
+      specifies that a controller can only handle
+      1-bit data transfers. New devices should use the generic
+      "bus-width = <1>" property.
+
+  sdhci,auto-cmd12:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      specifies that a controller can only handle auto CMD12.
+
+  voltage-ranges:
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    items:
+      items:
+        - description: specifies minimum slot voltage (mV).
+        - description: specifies maximum slot voltage (mV).
+    minItems: 1
+    maxItems: 8
+
+  dma-coherent: true
+
+  little-endian:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      If the host controller is little-endian mode, specify
+      this property. The default endian mode is big-endian.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+allOf:
+  - $ref: sdhci-common.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    mmc@2e000 {
+        compatible = "fsl,mpc8378-esdhc", "fsl,esdhc";
+        reg = <0x2e000 0x1000>;
+        interrupts = <42 0x8>;
+        interrupt-parent = <&ipic>;
+        /* Filled in by U-Boot */
+        clock-frequency = <100000000>;
+        voltage-ranges = <3300 3300>;
+    };
diff --git a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt b/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
deleted file mode 100644
index edb8cadb9541..000000000000
--- a/Documentation/devicetree/bindings/mmc/fsl-esdhc.txt
+++ /dev/null
@@ -1,52 +0,0 @@
-* Freescale Enhanced Secure Digital Host Controller (eSDHC)
-
-The Enhanced Secure Digital Host Controller provides an interface
-for MMC, SD, and SDIO types of memory cards.
-
-This file documents differences between the core properties described
-by mmc.txt and the properties used by the sdhci-esdhc driver.
-
-Required properties:
-  - compatible : should be "fsl,esdhc", or "fsl,<chip>-esdhc".
-    Possible compatibles for PowerPC:
-	"fsl,mpc8536-esdhc"
-	"fsl,mpc8378-esdhc"
-	"fsl,p2020-esdhc"
-	"fsl,p4080-esdhc"
-	"fsl,t1040-esdhc"
-	"fsl,t4240-esdhc"
-    Possible compatibles for ARM:
-	"fsl,ls1012a-esdhc"
-	"fsl,ls1028a-esdhc"
-	"fsl,ls1088a-esdhc"
-	"fsl,ls1043a-esdhc"
-	"fsl,ls1046a-esdhc"
-	"fsl,ls2080a-esdhc"
-  - clock-frequency : specifies eSDHC base clock frequency.
-
-Optional properties:
-  - sdhci,wp-inverted : specifies that eSDHC controller reports
-    inverted write-protect state; New devices should use the generic
-    "wp-inverted" property.
-  - sdhci,1-bit-only : specifies that a controller can only handle
-    1-bit data transfers. New devices should use the generic
-    "bus-width = <1>" property.
-  - sdhci,auto-cmd12: specifies that a controller can only handle auto
-    CMD12.
-  - voltage-ranges : two cells are required, first cell specifies minimum
-    slot voltage (mV), second cell specifies maximum slot voltage (mV).
-    Several ranges could be specified.
-  - little-endian : If the host controller is little-endian mode, specify
-    this property. The default endian mode is big-endian.
-
-Example:
-
-sdhci@2e000 {
-	compatible = "fsl,mpc8378-esdhc", "fsl,esdhc";
-	reg = <0x2e000 0x1000>;
-	interrupts = <42 0x8>;
-	interrupt-parent = <&ipic>;
-	/* Filled in by U-Boot */
-	clock-frequency = <0>;
-	voltage-ranges = <3300 3300>;
-};
diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml
index 36acc40c7d18..6e2cdac6a85d 100644
--- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml
+++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml
@@ -27,17 +27,19 @@ properties:
     maxItems: 1
 
   voltage-ranges:
-    $ref: /schemas/types.yaml#/definitions/uint32-array
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
     description: |
       Two cells are required, first cell specifies minimum slot voltage (mV),
       second cell specifies maximum slot voltage (mV).
     items:
-      - description: |
-          value for minimum slot voltage in mV
-        default: 3200
-      - description: |
-          value for maximum slot voltage in mV
-        default: 3400
+      items:
+        - description: |
+            value for minimum slot voltage in mV
+          default: 3200
+        - description: |
+            value for maximum slot voltage in mV
+          default: 3400
+    maxItems: 1
 
   gpios:
     description: |
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-msm.yaml b/Documentation/devicetree/bindings/mmc/sdhci-msm.yaml
index c24c537f62b1..11979b026d21 100644
--- a/Documentation/devicetree/bindings/mmc/sdhci-msm.yaml
+++ b/Documentation/devicetree/bindings/mmc/sdhci-msm.yaml
@@ -51,6 +51,7 @@ properties:
               - qcom,sdm845-sdhci
               - qcom,sdx55-sdhci
               - qcom,sdx65-sdhci
+              - qcom,sdx75-sdhci
               - qcom,sm6115-sdhci
               - qcom,sm6125-sdhci
               - qcom,sm6350-sdhci
diff --git a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt b/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt
deleted file mode 100644
index eb7eb1b529f0..000000000000
--- a/Documentation/devicetree/bindings/mmc/sdhci-sprd.txt
+++ /dev/null
@@ -1,67 +0,0 @@
-* Spreadtrum SDHCI controller (sdhci-sprd)
-
-The Secure Digital (SD) Host controller on Spreadtrum SoCs provides an interface
-for MMC, SD and SDIO types of cards.
-
-This file documents differences between the core properties in mmc.txt
-and the properties used by the sdhci-sprd driver.
-
-Required properties:
-- compatible: Should contain "sprd,sdhci-r11".
-- reg: physical base address of the controller and length.
-- interrupts: Interrupts used by the SDHCI controller.
-- clocks: Should contain phandle for the clock feeding the SDHCI controller
-- clock-names: Should contain the following:
-	"sdio" - SDIO source clock (required)
-	"enable" - gate clock which used for enabling/disabling the device (required)
-	"2x_enable" - gate clock controlling the device for some special platforms (optional)
-
-Optional properties:
-- assigned-clocks: the same with "sdio" clock
-- assigned-clock-parents: the default parent of "sdio" clock
-- pinctrl-names: should be "default", "state_uhs"
-- pinctrl-0: should contain default/high speed pin control
-- pinctrl-1: should contain uhs mode pin control
-
-PHY DLL delays are used to delay the data valid window, and align the window
-to sampling clock. PHY DLL delays can be configured by following properties,
-and each property contains 4 cells which are used to configure the clock data
-write line delay value, clock read command line delay value, clock read data
-positive edge delay value and clock read data negative edge delay value.
-Each cell's delay value unit is cycle of the PHY clock.
-
-- sprd,phy-delay-legacy: Delay value for legacy timing.
-- sprd,phy-delay-sd-highspeed: Delay value for SD high-speed timing.
-- sprd,phy-delay-sd-uhs-sdr50: Delay value for SD UHS SDR50 timing.
-- sprd,phy-delay-sd-uhs-sdr104: Delay value for SD UHS SDR50 timing.
-- sprd,phy-delay-mmc-highspeed: Delay value for MMC high-speed timing.
-- sprd,phy-delay-mmc-ddr52: Delay value for MMC DDR52 timing.
-- sprd,phy-delay-mmc-hs200: Delay value for MMC HS200 timing.
-- sprd,phy-delay-mmc-hs400: Delay value for MMC HS400 timing.
-- sprd,phy-delay-mmc-hs400es: Delay value for MMC HS400 enhanced strobe timing.
-
-Examples:
-
-sdio0: sdio@20600000 {
-	compatible  = "sprd,sdhci-r11";
-	reg = <0 0x20600000 0 0x1000>;
-	interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
-
-	clock-names = "sdio", "enable";
-	clocks = <&ap_clk CLK_EMMC_2X>,
-		 <&apahb_gate CLK_EMMC_EB>;
-	assigned-clocks = <&ap_clk CLK_EMMC_2X>;
-	assigned-clock-parents = <&rpll CLK_RPLL_390M>;
-
-	pinctrl-names = "default", "state_uhs";
-	pinctrl-0 = <&sd0_pins_default>;
-	pinctrl-1 = <&sd0_pins_uhs>;
-
-	sprd,phy-delay-sd-uhs-sdr104 = <0x3f 0x7f 0x2e 0x2e>;
-	bus-width = <8>;
-	non-removable;
-	no-sdio;
-	no-sd;
-	cap-mmc-hw-reset;
-	status = "okay";
-};
diff --git a/Documentation/devicetree/bindings/mmc/sprd,sdhci-r11.yaml b/Documentation/devicetree/bindings/mmc/sprd,sdhci-r11.yaml
new file mode 100644
index 000000000000..b08081bc018b
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/sprd,sdhci-r11.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: GPL-2.0 OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/sprd,sdhci-r11.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Spreadtrum SDHCI controller
+
+maintainers:
+  - Orson Zhai <orsonzhai@gmail.com>
+  - Baolin Wang <baolin.wang7@gmail.com>
+  - Chunyan Zhang <zhang.lyra@gmail.com>
+
+properties:
+  compatible:
+    const: sprd,sdhci-r11
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 2
+    items:
+      - description: SDIO source clock
+      - description: gate clock for enabling/disabling the device
+      - description: gate clock controlling the device for some special platforms (optional)
+
+  clock-names:
+    minItems: 2
+    items:
+      - const: sdio
+      - const: enable
+      - const: 2x_enable
+
+  pinctrl-0:
+    description: default/high speed pin control
+    maxItems: 1
+
+  pinctrl-1:
+    description: UHS mode pin control
+    maxItems: 1
+
+  pinctrl-names:
+    minItems: 1
+    items:
+      - const: default
+      - const: state_uhs
+
+patternProperties:
+  "^sprd,phy-delay-(legacy|mmc-(ddr52|highspeed|hs[24]00|hs400es)|sd-(highspeed|uhs-sdr(50|104)))$":
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    items:
+      - description: clock data write line delay value
+      - description: clock read command line delay value
+      - description: clock read data positive edge delay value
+      - description: clock read data negative edge delay value
+    description:
+      PHY DLL delays are used to delay the data valid window, and align
+      the window to the sampling clock. Each cell's delay value unit is
+      cycle of the PHY clock.
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+allOf:
+  - $ref: sdhci-common.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/sprd,sc9860-clk.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/interrupt-controller/irq.h>
+
+    mmc@50430000 {
+      compatible = "sprd,sdhci-r11";
+      reg = <0x50430000 0x1000>;
+      interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+
+      clocks = <&aon_prediv CLK_EMMC_2X>,
+               <&apahb_gate CLK_EMMC_EB>,
+               <&aon_gate CLK_EMMC_2X_EN>;
+      clock-names = "sdio", "enable", "2x_enable";
+
+      pinctrl-0 = <&sd0_pins_default>;
+      pinctrl-1 = <&sd0_pins_uhs>;
+      pinctrl-names = "default", "state_uhs";
+
+      bus-width = <8>;
+      cap-mmc-hw-reset;
+      mmc-hs400-enhanced-strobe;
+      mmc-hs400-1_8v;
+      mmc-hs200-1_8v;
+      mmc-ddr-1_8v;
+      non-removable;
+      no-sdio;
+      no-sd;
+
+      sprd,phy-delay-mmc-ddr52 = <0x3f 0x75 0x14 0x14>;
+      sprd,phy-delay-mmc-hs200 = <0x0 0x8c 0x8c 0x8c>;
+      sprd,phy-delay-mmc-hs400 = <0x44 0x7f 0x2e 0x2e>;
+      sprd,phy-delay-mmc-hs400es = <0x3f 0x3f 0x2e 0x2e>;
+    };
+...