pinctrl: Keep enum pin_config_param ordered by name (part 2)

It seems the ordering is by name. Keep it that way.
Here updating the entire list (there were two more options not in order).

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210510194717.12255-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1 files changed, 10 insertions, 10 deletions

diff --git a/include/linux/pinctrl/pinconf-generic.h b/include/linux/pinctrl/pinconf-generic.h
index e18ab3d5908f..98ed5959ca9a 100644
--- a/include/linux/pinctrl/pinconf-generic.h
+++ b/include/linux/pinctrl/pinconf-generic.h
@@ -81,28 +81,28 @@ struct pinctrl_map;
  *	passed in the argument on a custom form, else just use argument 1
  *	to indicate low power mode, argument 0 turns low power mode off.
  * @PIN_CONFIG_MODE_PWM: this will configure the pin for PWM
+ * @PIN_CONFIG_OUTPUT: this will configure the pin as an output and drive a
+ * 	value on the line. Use argument 1 to indicate high level, argument 0 to
+ *	indicate low level. (Please see Documentation/driver-api/pinctl.rst,
+ *	section "GPIO mode pitfalls" for a discussion around this parameter.)
  * @PIN_CONFIG_OUTPUT_ENABLE: this will enable the pin's output mode
  * 	without driving a value there. For most platforms this reduces to
  * 	enable the output buffers and then let the pin controller current
  * 	configuration (eg. the currently selected mux function) drive values on
  * 	the line. Use argument 1 to enable output mode, argument 0 to disable
  * 	it.
- * @PIN_CONFIG_OUTPUT: this will configure the pin as an output and drive a
- * 	value on the line. Use argument 1 to indicate high level, argument 0 to
- *	indicate low level. (Please see Documentation/driver-api/pinctl.rst,
- *	section "GPIO mode pitfalls" for a discussion around this parameter.)
  * @PIN_CONFIG_PERSIST_STATE: retain pin state across sleep or controller reset
  * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power
  *	supplies, the argument to this parameter (on a custom format) tells
  *	the driver which alternative power source to use.
- * @PIN_CONFIG_SLEEP_HARDWARE_STATE: indicate this is sleep related state.
- * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
- *	this parameter (on a custom format) tells the driver which alternative
- *	slew rate to use.
  * @PIN_CONFIG_SKEW_DELAY: if the pin has programmable skew rate (on inputs)
  *	or latch delay (on outputs) this parameter (in a custom format)
  *	specifies the clock skew or latch delay. It typically controls how
  *	many double inverters are put in front of the line.
+ * @PIN_CONFIG_SLEEP_HARDWARE_STATE: indicate this is sleep related state.
+ * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to
+ *	this parameter (on a custom format) tells the driver which alternative
+ *	slew rate to use.
  * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if
  *	you need to pass in custom configurations to the pin controller, use
  *	PIN_CONFIG_END+1 as the base offset.
@@ -127,13 +127,13 @@ enum pin_config_param {
 	PIN_CONFIG_INPUT_SCHMITT_ENABLE,
 	PIN_CONFIG_MODE_LOW_POWER,
 	PIN_CONFIG_MODE_PWM,
-	PIN_CONFIG_OUTPUT_ENABLE,
 	PIN_CONFIG_OUTPUT,
+	PIN_CONFIG_OUTPUT_ENABLE,
 	PIN_CONFIG_PERSIST_STATE,
 	PIN_CONFIG_POWER_SOURCE,
+	PIN_CONFIG_SKEW_DELAY,
 	PIN_CONFIG_SLEEP_HARDWARE_STATE,
 	PIN_CONFIG_SLEW_RATE,
-	PIN_CONFIG_SKEW_DELAY,
 	PIN_CONFIG_END = 0x7F,
 	PIN_CONFIG_MAX = 0xFF,
 };