| Age | Commit message (Collapse) | Author |
|---|
|
This allows the mesh sync (and debugfs) code to make incremental
TSF adjustments, avoiding any uncertainty introduced by delay in
programming absolute TSF.
Signed-off-by: Thomas Pedersen <twp@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implement add/rm_nan_func functions and handle NAN function
termination notifications. Handle instance_id allocation for
NAN functions and implement the reconfig flow.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implement nan_change_conf callback which allows to change current
NAN configuration (master preference and dual band operation).
Store the current NAN configuration in sdata, so it can be used
both to provide the driver the updated configuration with changes
and also it will be used in hw reconfig flows in next patches.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This code doesn't do much besides allowing to start and
stop the vif.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some devices, like iwlwifi, have RSS queues. This may cause a
situation where a disassociation is handled in control path and
results in station removal while there are prior RX frames
that were still not processed in other queues. When they will
be processed the station will be gone, and the frames will be
dropped.
Add a synchronization interface to avoid that. When driver returns
from the synchronization mac80211 may remove the station.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently mac80211 does not inform the driver of the session
block ack timeout when starting a rx aggregation session.
Drivers that manage the reorder buffer need to know this
parameter.
Seeing that there are now too many arguments for the
drv_ampdu_action() function, wrap them inside a structure.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This can happen when the driver needs to send less frames
than expected and then needs to close the SP.
Mac80211 still needs to set the more_data properly based
on its buffer state (ps_tx_buffer and buffered frames on
other TIDs).
To that end, refactor the code that delivers frames upon
uAPSD trigger frames to be able to get only the more_data
bit without actually delivering those frames in case the
driver is just asking to set a NDP with EOSP and MORE_DATA
bit properly set.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In TDLS channel-switch operations the chandef can sometimes be NULL.
Avoid an oops in the trace code for these cases and just print a
chandef full of zeros.
Cc: stable@vger.kernel.org
Fixes: a7a6bdd0670fe ("mac80211: introduce TDLS channel switch ops")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As this API has never really seen any use and most drivers don't
ever use the value derived from it, remove it.
Change the only driver using it (rt2x00) to simply use the DTIM
period instead of the "max sleep" time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Advertise the capability to send A-MSDU within A-MPDU
in the AddBA request sent by mac80211. Let the driver
know about the peer's capabilities.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently the cfg80211's frame registration api receives wdev, however
mac80211 assumes per device filter configuration and ignores wdev.
Per device filtering is too wasteful, especially for multi-channel
devices.
Introduce new per vif frame registration API and use it for probe
request registrations in ieee80211_mgmt_frame_register()
Also call directly to ieee80211_configure_filter instead of using a work
since it is now allowed to sleep in ieee80211_mgmt_frame_register.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Extend the function to read the TKIP IV32/IV16 to read the IV/PN for
all ciphers in order to allow drivers with full hardware crypto to
properly support this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull networking updates from David Miller:
1) Add BQL support to via-rhine, from Tino Reichardt.
2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
can support hw switch offloading. From Floria Fainelli.
3) Allow 'ip address' commands to initiate multicast group join/leave,
from Madhu Challa.
4) Many ipv4 FIB lookup optimizations from Alexander Duyck.
5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
Borkmann.
6) Remove the ugly compat support in ARP for ugly layers like ax25,
rose, etc. And use this to clean up the neigh layer, then use it to
implement MPLS support. All from Eric Biederman.
7) Support L3 forwarding offloading in switches, from Scott Feldman.
8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
up route lookups even further. From Alexander Duyck.
9) Many improvements and bug fixes to the rhashtable implementation,
from Herbert Xu and Thomas Graf. In particular, in the case where
an rhashtable user bulk adds a large number of items into an empty
table, we expand the table much more sanely.
10) Don't make the tcp_metrics hash table per-namespace, from Eric
Biederman.
11) Extend EBPF to access SKB fields, from Alexei Starovoitov.
12) Split out new connection request sockets so that they can be
established in the main hash table. Much less false sharing since
hash lookups go direct to the request sockets instead of having to
go first to the listener then to the request socks hashed
underneath. From Eric Dumazet.
13) Add async I/O support for crytpo AF_ALG sockets, from Tadeusz Struk.
14) Support stable privacy address generation for RFC7217 in IPV6. From
Hannes Frederic Sowa.
15) Hash network namespace into IP frag IDs, also from Hannes Frederic
Sowa.
16) Convert PTP get/set methods to use 64-bit time, from Richard
Cochran.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1816 commits)
fm10k: Bump driver version to 0.15.2
fm10k: corrected VF multicast update
fm10k: mbx_update_max_size does not drop all oversized messages
fm10k: reset head instead of calling update_max_size
fm10k: renamed mbx_tx_dropped to mbx_tx_oversized
fm10k: update xcast mode before synchronizing multicast addresses
fm10k: start service timer on probe
fm10k: fix function header comment
fm10k: comment next_vf_mbx flow
fm10k: don't handle mailbox events in iov_event path and always process mailbox
fm10k: use separate workqueue for fm10k driver
fm10k: Set PF queues to unlimited bandwidth during virtualization
fm10k: expose tx_timeout_count as an ethtool stat
fm10k: only increment tx_timeout_count in Tx hang path
fm10k: remove extraneous "Reset interface" message
fm10k: separate PF only stats so that VF does not display them
fm10k: use hw->mac.max_queues for stats
fm10k: only show actual queues, not the maximum in hardware
fm10k: allow creation of VLAN on default vid
fm10k: fix unused warnings
...
|
|
Every tracing file must have its own TRACE_SYSTEM defined.
The mac80211 tracepoint header broke this and add in the middle
of the file had:
#undef TRACE_SYSTEM
#define TRACE_SYSTEM mac80211_msg
Unfortunately, this broke new code in the ftrace infrastructure.
Moving the mac80211_msg into its own trace file with its own
TRACE_SYSTEM defined fixes the issue.
Link: http://lkml.kernel.org/r/1428389938.1841.1.camel@sipsolutions.net
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.
The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.
This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We will be able to add more events, such as MLME events and
others. The low level driver may be interested in knowing
about these events to dump firmware data upon failures, or
to change parameters in case connection attempts fail etc...
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In many cases, drivers can filter things like beacons that will
skew statistics reported by mac80211. To get correct statistics
in these cases, call drivers to obtain statistics and let them
override all values, filling values from mac80211 if the driver
didn't provide them. Not all of them make sense for the driver
to fill, so some are still always done by mac80211.
Note that this doesn't currently allow a driver to say "I know
this value is wrong, don't report it at all", or to sum it up
with a mac80211 value (as could be useful for "dropped misc"),
that can be added if it turns out to be needed.
This also gets rid of the get_rssi() method as is can now be
implemented using sta_statistics().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Having it as a sub-event for RSSI thresholds is very ugly,
but luckily no userspace actually uses the events yet.
Move the event to its own function call internally and to
its own event attribute in nl80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows drivers with a firmware or chip-based rate lookup table to
use the most recent default rate selection without having to get it from
per-packet data or explicit ieee80211_get_tx_rate calls
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow drivers to support NL80211_SCAN_FLAG_RANDOM_ADDR with software
based scanning and generate a random MAC address for them for every
scan request with the flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When receiving a TDLS channel switch request or response, parse the frame
and call a new tdls_recv_channel_switch op in the low level driver with
the parsed data.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implement the cfg80211 TDLS channel switch ops and introduce new mac80211
ones for low-level drivers.
Verify low-level driver support for the new ops when using the relevant
wiphy feature bit. Also verify the peer supports channel switching before
passing the command down.
Add a new STA flag to track the off-channel state with the TDLS peer and
make sure to cancel the channel-switch if the peer STA is unexpectedly
removed.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The device_timestamp value was left out of the event trace for
drv_pre_channel_switch by mistake. Add it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers might want to know also when mac80211 has
completed reconfiguring after resume (e.g. in order
to know when frames can be passed to mac80211).
Rename restart_complete() to a more-generic reconfig_complete(),
and add a new enum to indicate the reconfiguration type.
Update the current users with the new prototype.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The configured tx power is often limited by hardware capabilities,
channel settings, antenna configuration, etc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[fix tracing compilation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Channel switch with multiple channel contexts should now work fine.
Remove check that disallows switches when multiple contexts are in
use.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As a counterpart to the pre_channel_switch operation, add a
post_channel_switch operation. This allows the drivers to go back to
a normal configuration after the channel switch is completed.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some drivers may need to prepare for a channel switch also when it is
initiated from the remote side (eg. station, P2P client). To make
this possible, add a generic callback that can be called for all
interface types.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some devices may need the device timestamp in order to synchronize the
channel switch. To pass this value back to the driver, add it to the
channel switch structure and copy the device_timestamp value received
in the rx info structure into it.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Extend mac80211 set_coverage_class API in order to enable ACK timeout
estimation algorithm (dynack) passing coverage class equals to -1
to lower drivers. Synchronize set_coverage_class routine signature with
mac80211 function pointer for p54, ath9k, ath9k_htc and ath5k drivers.
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After sending a TDLS discovery-request, we expect a reply to arrive on
the AP's channel. We must stay on the channel (no PSM, scan, etc.), since
a TDLS setup-response is a direct packet not buffered by the AP.
Add a new mac80211 driver callback to allow discovery session protection.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
In some cases, when the driver is already using all the channel
contexts it can handle at once, we have to do an in-place switch
(ie. we cannot afford using an extra context temporarily for the
transaction). But some drivers may not support switching the channel
context assigned to a vif on the fly (ie. without unassigning and
assigning it) while others may only work if the context is changed on
the fly, without unassigning it first.
To allow these different scenarios, add a new driver operation that
let's the driver decide how to handle an in-place switch.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
Add get_expected_throughput() API to mac80211 so that each
driver can implement its own version based on the RC
algorithm they are using (might be using an HW RC algo).
The API returns a value expressed in Kbps.
Also, add the new get_expected_throughput() member
to the rate_control_ops structure in order to be
able to query the RC algorithm (this patch provides an
implementation of this API for both minstrel and
minstrel_ht).
The related member in the station_info object is now
filled accordingly when dumping a station.
Cc: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If sdata doesn't have a valid dev (e.g. in case of monitor
vif), the vif_name field was initialized with (a length of)
some short string, but later was set to a different,
potentially larger one.
This resulted in out-of-bounds write, which usually
appeared as garbage in the trace log.
Simply trace sdata->name, as it should always have the
correct name for both cases.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is useful for debugging issues with drivers using this
function (erroneously), so add tracing for the API call.
Change-Id: Ice9d7eabb8fecbac188f0a741920d3488de700ec
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix a number of different checkpatch errors.
Signed-off-by: Weilong Chen <chenweilong@huawei.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, mac80211 allows drivers to keep RCU-protected station
references that are cleared when the station is removed from the
driver and consequently needs to synchronize twice, once before
removing the station from the driver (so it can guarantee that
the station is no longer used in TX towards the driver) and once
after the station is removed from the driver.
Add a new pre-RCU-synchronisation station removal operation to
the API to allow drivers to clear/invalidate their RCU-protected
station pointers before the RCU synchronisation.
This will allow removing the second synchronisation by changing
the driver API so that the driver may no longer assume a valid
RCU-protected pointer after sta_remove/sta_state returns.
The alternative to this would be to synchronize_rcu() in all the
drivers that currently rely on this behaviour (only iwlmvm) but
that would defeat the purpose.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
|
|
This reverts commit 488b366a452934141959384c7a1b52b22d6154ef.
The code isn't used by anyone, and the Intel driver isn't planning
to use it either right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
Add a new field to ieee80211_chanctx_conf to indicate
the min required channel configuration.
Tuning to a narrower channel might help reducing
the noise level and saving some power.
The min required channel definition is the max of
all min required channel definitions of the interfaces
bound to this channel context.
In AP mode, use 20MHz when there are no connected station.
When a new station is added/removed, calculate the new max
bandwidth supported by any of the stations (e.g. 80MHz when
80MHz and 40MHz stations are connected).
In other cases, simply use bss_conf.chandef as the
min required chandef.
Notify drivers about changes to this field by calling
drv_change_chanctx with a new CHANGE_MIN_WIDTH notification.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
Convert the memset/memcpy uses of 6 to ETH_ALEN
where appropriate.
Also convert some struct definitions and u8 array
declarations of [6] to ETH_ALEN.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This can be useful for drivers if they have any failure cases
when joining an IBSS. Also move setting the queue parameters
to before this new call, in case the new driver op needs them
already.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The count field in CSA must be decremented with each beacon
transmitted. This patch implements the functionality for drivers
using ieee80211_beacon_get(). Other drivers must call back manually
after reaching count == 0.
This patch also contains the handling and finish worker for the channel
switch command, and mac80211/chanctx code to allow to change a channel
definition of an active channel context.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[small cleanups, catch identical chandef]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers that don't use chanctxes cannot perform VHT association because
they still use a "backward compatibility" pair of {ieee80211_channel,
nl80211_channel_type} in ieee80211_conf and ieee80211_local.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
[fix kernel-doc]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
