| Age | Commit message (Collapse) | Author |
|---|
|
This should never have landed in the first place: it was added as part
of 64-bit divide support for 32-bit systems, but the kernel doesn't
allow this sort of division. I must have forgotten to remove it.
This patch removes the support. Since this routine only worked on
64-bit platforms but was only built on 32-bit platforms, it's
essentially just nonsense anyway.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Link: https://lore.kernel.org/linux-riscv/nycvar.YSQ.7.76.1908061413360.19480@knanqh.ubzr/T/#t
Reported-by: Eric Lin <tesheng@andestech.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
In preparation for removing __udivdi3() from the RISC-V
architecture-specific files, convert its one user to use do_div().
This avoids breaking the RV32 build after __udivdi3() is removed.
This second version removes the assignment of the remainder to an
unused temporary variable. Thanks to Nicolas Pitre <nico@fluxnic.net>
for the suggestion.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
|
|
Align the RV64 defconfig to the output of "make savedefconfig" to
avoid unnecessary deltas for future defconfig patches. This patch
should have no runtime functional impact.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
On FU540-based systems, the "timebase-frequency" (RTCCLK) is sourced
from an external crystal located on the PCB. Thus the
timebase-frequency DT property should be defined by the board that
uses the SoC, not the SoC itself. Drop the superfluous
timebase-frequency property from the SoC DT data. (It's already
present in the board DT data.)
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
|
|
This patch fix following perf record error by linking vdso.so with
build id.
perf.data perf.data.old
[ perf record: Woken up 1 times to write data ]
free(): double free detected in tcache 2
Aborted
perf record use filename__read_build_id(util/symbol-minimal.c) to get
build id when libelf is not supported. When vdso.so is linked without
build id, the section size of PT_NOTE will be zero, buf size will
realloc to zero and cause memory corruption.
Signed-off-by: Mao Han <han_mao@c-sky.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX fixes from Greg KH:
"Here are some small SPDX fixes for 5.3-rc2 for things that came in
during the 5.3-rc1 merge window that we previously missed.
Only three small patches here:
- two uapi patches to resolve some SPDX tags that were not correct
- fix an invalid SPDX tag in the iomap Makefile file
All have been properly reviewed on the public mailing lists"
* tag 'spdx-5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx:
iomap: fix Invalid License ID
treewide: remove SPDX "WITH Linux-syscall-note" from kernel-space headers again
treewide: add "WITH Linux-syscall-note" to SPDX tag of uapi headers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
"Four minor RISC-V-related changes:
- Add support for the new clone3 syscall for RV64, relying on the
generic support
- Add DT data for the gigabit Ethernet controller on the SiFive FU540
and the HiFive Unleashed board
- Update MAINTAINERS to add me to the arch/riscv maintainers' list
- Add support for PCIe message-signaled interrupts by reusing the
generic header file"
* tag 'riscv/for-v5.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: dts: Add DT node for SiFive FU540 Ethernet controller driver
riscv: include generic support for MSI irqdomains
MAINTAINERS: Add Paul as a RISC-V maintainer
riscv: enable sys_clone3 syscall for rv64
|
|
UAPI headers licensed under GPL are supposed to have exception
"WITH Linux-syscall-note" so that they can be included into non-GPL
user space application code.
The exception note is missing in some UAPI headers.
Some of them slipped in by the treewide conversion commit b24413180f56
("License cleanup: add SPDX GPL-2.0 license identifier to files with
no license"). Just run:
$ git show --oneline b24413180f56 -- arch/x86/include/uapi/asm/
I believe they are not intentional, and should be fixed too.
This patch was generated by the following script:
git grep -l --not -e Linux-syscall-note --and -e SPDX-License-Identifier \
-- :arch/*/include/uapi/asm/*.h :include/uapi/ :^*/Kbuild |
while read file
do
sed -i -e '/[[:space:]]OR[[:space:]]/s/\(GPL-[^[:space:]]*\)/(\1 WITH Linux-syscall-note)/g' \
-e '/[[:space:]]or[[:space:]]/s/\(GPL-[^[:space:]]*\)/(\1 WITH Linux-syscall-note)/g' \
-e '/[[:space:]]OR[[:space:]]/!{/[[:space:]]or[[:space:]]/!s/\(GPL-[^[:space:]]*\)/\1 WITH Linux-syscall-note/g}' $file
done
After this patch is applied, there are 5 UAPI headers that do not contain
"WITH Linux-syscall-note". They are kept untouched since this exception
applies only to GPL variants.
$ git grep --not -e Linux-syscall-note --and -e SPDX-License-Identifier \
-- :arch/*/include/uapi/asm/*.h :include/uapi/ :^*/Kbuild
include/uapi/drm/panfrost_drm.h:/* SPDX-License-Identifier: MIT */
include/uapi/linux/batman_adv.h:/* SPDX-License-Identifier: MIT */
include/uapi/linux/qemu_fw_cfg.h:/* SPDX-License-Identifier: BSD-3-Clause */
include/uapi/linux/vbox_err.h:/* SPDX-License-Identifier: MIT */
include/uapi/linux/virtio_iommu.h:/* SPDX-License-Identifier: BSD-3-Clause */
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DT node for SiFive FU540-C000 GEMGXL Ethernet controller driver added
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
Cc: Andrew Lunn <andrew@lunn.ch>
[paul.walmsley@sifive.com: changed "phy1" to "phy0" at Andrew Lunn's
suggestion]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Some RISC-V systems include PCIe host controllers that support PCIe
message-signaled interrupts. For this to work on Linux, we need to
enable PCI_MSI_IRQ_DOMAIN and define struct msi_alloc_info. Support
for the latter is enabled by including the architecture-generic msi.h
include.
Signed-off-by: Wesley Terpstra <wesley@sifive.com>
[paul.walmsley@sifive.com: split initial patch into one arch/riscv
patch and one drivers/pci patch]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- match the directory structure of the linux-libc-dev package to that
of Debian-based distributions
- fix incorrect include/config/auto.conf generation when Kconfig
creates it along with the .config file
- remove misleading $(AS) from documents
- clean up precious tag files by distclean instead of mrproper
- add a new coccinelle patch for devm_platform_ioremap_resource
migration
- refactor module-related scripts to read modules.order instead of
$(MODVERDIR)/*.mod files to get the list of created modules
- remove MODVERDIR
- update list of header compile-test
- add -fcf-protection=none flag to avoid conflict with the retpoline
flags when CONFIG_RETPOLINE=y
- misc cleanups
* tag 'kbuild-v5.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (25 commits)
kbuild: add -fcf-protection=none when using retpoline flags
kbuild: update compile-test header list for v5.3-rc1
kbuild: split out *.mod out of {single,multi}-used-m rules
kbuild: remove 'prepare1' target
kbuild: remove the first line of *.mod files
kbuild: create *.mod with full directory path and remove MODVERDIR
kbuild: export_report: read modules.order instead of .tmp_versions/*.mod
kbuild: modpost: read modules.order instead of $(MODVERDIR)/*.mod
kbuild: modsign: read modules.order instead of $(MODVERDIR)/*.mod
kbuild: modinst: read modules.order instead of $(MODVERDIR)/*.mod
scsi: remove pointless $(MODVERDIR)/$(obj)/53c700.ver
kbuild: remove duplication from modules.order in sub-directories
kbuild: get rid of kernel/ prefix from in-tree modules.{order,builtin}
kbuild: do not create empty modules.order in the prepare stage
coccinelle: api: add devm_platform_ioremap_resource script
kbuild: compile-test headers listed in header-test-m as well
kbuild: remove unused hostcc-option
kbuild: remove tag files by distclean instead of mrproper
kbuild: add --hash-style= and --build-id unconditionally
kbuild: get rid of misleading $(AS) from documents
...
|
|
Enable the sys_clone3 syscall for RV64. We simply include the generic
version.
Tested by running the program from
https://lore.kernel.org/lkml/20190716130631.tohj4ub54md25dys@brauner.io/
and verifying that it completes successfully.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Acked-by: Christian Brauner <christian@brauner.io>
Cc: Christian Brauner <christian@brauner.io>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V updates from Paul Walmsley:
- Hugepage support
- "Image" header support for RISC-V kernel binaries, compatible with
the current ARM64 "Image" header
- Initial page table setup now split into two stages
- CONFIG_SOC support (starting with SiFive SoCs)
- Avoid reserving memory between RAM start and the kernel in
setup_bootmem()
- Enable high-res timers and dynamic tick in the RV64 defconfig
- Remove long-deprecated gate area stubs
- MAINTAINERS updates to switch to the newly-created shared RISC-V git
tree, and to fix a get_maintainers.pl issue for patches involving
SiFive E-mail addresses
Also, one integration fix to resolve a build problem introduced during
in the v5.3-rc1 merge window:
- Fix build break after macro-to-function conversion in
asm-generic/cacheflush.h
* tag 'riscv/for-v5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: fix build break after macro-to-function conversion in generic cacheflush.h
RISC-V: Add an Image header that boot loader can parse.
RISC-V: Setup initial page tables in two stages
riscv: remove free_initrd_mem
riscv: ccache: Remove unused variable
riscv: Introduce huge page support for 32/64bit kernel
x86, arm64: Move ARCH_WANT_HUGE_PMD_SHARE config in arch/Kconfig
RISC-V: Fix memory reservation in setup_bootmem()
riscv: defconfig: enable SOC_SIFIVE
riscv: select SiFive platform drivers with SOC_SIFIVE
arch: riscv: add config option for building SiFive's SoC resource
riscv: Remove gate area stubs
MAINTAINERS: change the arch/riscv git tree to the new shared tree
MAINTAINERS: don't automatically patches involving SiFive to the linux-riscv list
RISC-V: defconfig: Enable NO_HZ_IDLE and HIGH_RES_TIMERS
|
|
cacheflush.h
Commit c296d4dc13ae ("asm-generic: fix a compilation warning")
converted the various flush_*cache_* macros in
asm-generic/cacheflush.h to static inline functions. This breaks
RISC-V builds, since RISC-V's cacheflush.h includes the generic
cacheflush.h and then undefines the macros to be overridden.
Fix by copying the subset of the no-op functions that are reused from
the generic cacheflush.h into the RISC-V cacheflush.h, and dropping
the include of the generic cacheflush.h.
Fixes: c296d4dc13ae ("asm-generic: fix a compilation warning")
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The top level Makefile adds -Wall globally:
KBUILD_CFLAGS := -Wall -Wundef -Werror=strict-prototypes -Wno-trigraphs \
For riscv, I see two "-Wall" added for compiling each object.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kconfig updates from Masahiro Yamada:
- always require argument for --defconfig and remove the hard-coded
arch/$(ARCH)/defconfig path
- make arch/$(SRCARCH)/configs/defconfig the new default of defconfig
- some code cleanups
* tag 'kconfig-v5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: remove meaningless if-conditional in conf_read()
kconfig: Fix spelling of sym_is_changable
unicore32: rename unicore32_defconfig to defconfig
kconfig: make arch/*/configs/defconfig the default of KBUILD_DEFCONFIG
kconfig: add static qualifier to expand_string()
kconfig: require the argument of --defconfig
kconfig: remove always false ifeq ($(KBUILD_DEFCONFIG,) conditional
|
|
The only difference between the generic and RISC-V implementation of PTE
allocation is the usage of __GFP_RETRY_MAYFAIL for both kernel and user
PTEs and the absence of __GFP_ACCOUNT for the user PTEs.
The conversion to the generic version removes the __GFP_RETRY_MAYFAIL and
ensures that GFP_ACCOUNT is used for the user PTE allocations.
The pte_free() and pte_free_kernel() versions are identical to the generic
ones and can be simply dropped.
Link: http://lkml.kernel.org/r/1557296232-15361-13-git-send-email-rppt@linux.ibm.com
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sam Creasey <sammy@sammy.net>
Cc: Vincent Chen <deanbo422@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently, the last stage boot loaders such as U-Boot can accept only
uImage which is an unnecessary additional step in automating boot
process.
Add an image header that boot loader understands and boot Linux from
flat Image directly.
This header is based on ARM64 boot image header and provides an
opportunity to combine both ARM64 & RISC-V image headers in future.
Also make sure that PE/COFF header can co-exist in the same image so
that EFI stub can be supported for RISC-V in future. EFI specification
needs PE/COFF image header in the beginning of the kernel image in order
to load it as an EFI application. In order to support EFI stub, code0
should be replaced with "MZ" magic string and res4(at offset 0x3c)
should point to the rest of the PE/COFF header (which will be added
during EFI support).
Tested on both QEMU and HiFive Unleashed using OpenSBI + U-Boot + Linux.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Karsten Merker <merker@debian.org>
Tested-by: Karsten Merker <merker@debian.org> (QEMU+OpenSBI+U-Boot)
Tested-by: Kevin Hilman <khilman@baylibre.com> (OpenSBI + U-Boot + Linux)
[paul.walmsley@sifive.com: fixed whitespace in boot-image-header.txt;
converted structure comment to kernel-doc format and added some detail]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu
Pull m68nommu updates from Greg Ungerer:
"A series of cleanups for the FLAT format binary loader, binfmt_flat,
from Christoph.
The end goal is to support no-MMU on RISC-V, and the last patch
enables that"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
riscv: add binfmt_flat support
binfmt_flat: don't offset the data start
binfmt_flat: move the MAX_SHARED_LIBS definition to binfmt_flat.c
binfmt_flat: remove the persistent argument from flat_get_addr_from_rp
binfmt_flat: provide an asm-generic/flat.h
binfmt_flat: make support for old format binaries optional
binfmt_flat: add a ARCH_HAS_BINFMT_FLAT option
binfmt_flat: add endianess annotations
binfmt_flat: use fixed size type for the on-disk format
binfmt_flat: consolidate two version of flat_v2_reloc_t
binfmt_flat: remove the unused OLD_FLAT_FLAG_RAM definition
binfmt_flat: remove the uapi <linux/flat.h> header
binfmt_flat: replace flat_argvp_envp_on_stack with a Kconfig variable
binfmt_flat: remove flat_old_ram_flag
binfmt_flat: provide a default version of flat_get_relocate_addr
binfmt_flat: remove flat_set_persistent
binfmt_flat: remove flat_reloc_valid
|
|
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull EDAC updates from Tony Luck:
"All the bits that Boris had queued in his tree plus four patches to
add support for Intel Icelake Xeon and then fix a few corner cases"
* tag 'please-pull-for_5.3' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
EDAC: Fix global-out-of-bounds write when setting edac_mc_poll_msec
EDAC, skx, i10nm: Fix source ID register offset
EDAC, i10nm: Check ECC enabling status per channel
EDAC, i10nm: Add Intel additional Ice-Lake support
EDAC: Make edac_debugfs_create_x*() return void
EDAC/aspeed: Remove set but not used variable 'np'
EDAC/ie31200: Reformat PCI device table
EDAC/ie31200: Add Intel Coffee Lake CPU support
EDAC/sifive: Add EDAC platform driver for SiFive SoCs
EDAC/sb_edac: Remove redundant update of tad_base
arm64: dts: stratix10: Add SDMMC EDAC node
EDAC/altera: Add Stratix10 SDMMC support
arm64: dts: stratix10: Add OCRAM EDAC node
EDAC/altera: Add Stratix10 OCRAM ECC support
EDAC/sysfs: Drop device references properly
EDAC/sysfs: Fix memory leak when creating a csrow object
|
|
Currently, the setup_vm() does initial page table setup in one-shot
very early before enabling MMU. Due to this, the setup_vm() has to map
all possible kernel virtual addresses since it does not know size and
location of RAM. This means we have kernel mappings for non-existent
RAM and any buggy driver (or kernel) code doing out-of-bound access
to RAM will not fault and cause underterministic behaviour.
Further, the setup_vm() creates PMD mappings (i.e. 2M mappings) for
RV64 systems. This means for PAGE_OFFSET=0xffffffe000000000 (i.e.
MAXPHYSMEM_128GB=y), the setup_vm() will require 129 pages (i.e.
516 KB) of memory for initial page tables which is never freed. The
memory required for initial page tables will further increase if
we chose a lower value of PAGE_OFFSET (e.g. 0xffffff0000000000)
This patch implements two-staged initial page table setup, as follows:
1. Early (i.e. setup_vm()): This stage maps kernel image and DTB in
a early page table (i.e. early_pg_dir). The early_pg_dir will be used
only by boot HART so it can be freed as-part of init memory free-up.
2. Final (i.e. setup_vm_final()): This stage maps all possible RAM
banks in the final page table (i.e. swapper_pg_dir). The boot HART
will start using swapper_pg_dir at the end of setup_vm_final(). All
non-boot HARTs directly use the swapper_pg_dir created by boot HART.
We have following advantages with this new approach:
1. Kernel mappings for non-existent RAM don't exists anymore.
2. Memory consumed by initial page tables is now indpendent of the
chosen PAGE_OFFSET.
3. Memory consumed by initial page tables on RV64 system is 2 pages
(i.e. 8 KB) which has significantly reduced and these pages will be
freed as-part of the init memory free-up.
The patch also provides a foundation for implementing strict kernel
mappings where we protect kernel text and rodata using PTE permissions.
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
[paul.walmsley@sifive.com: updated to apply; fixed a checkpatch warning]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull force_sig() argument change from Eric Biederman:
"A source of error over the years has been that force_sig has taken a
task parameter when it is only safe to use force_sig with the current
task.
The force_sig function is built for delivering synchronous signals
such as SIGSEGV where the userspace application caused a synchronous
fault (such as a page fault) and the kernel responded with a signal.
Because the name force_sig does not make this clear, and because the
force_sig takes a task parameter the function force_sig has been
abused for sending other kinds of signals over the years. Slowly those
have been fixed when the oopses have been tracked down.
This set of changes fixes the remaining abusers of force_sig and
carefully rips out the task parameter from force_sig and friends
making this kind of error almost impossible in the future"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (27 commits)
signal/x86: Move tsk inside of CONFIG_MEMORY_FAILURE in do_sigbus
signal: Remove the signal number and task parameters from force_sig_info
signal: Factor force_sig_info_to_task out of force_sig_info
signal: Generate the siginfo in force_sig
signal: Move the computation of force into send_signal and correct it.
signal: Properly set TRACE_SIGNAL_LOSE_INFO in __send_signal
signal: Remove the task parameter from force_sig_fault
signal: Use force_sig_fault_to_task for the two calls that don't deliver to current
signal: Explicitly call force_sig_fault on current
signal/unicore32: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from __do_user_fault
signal/arm: Remove tsk parameter from ptrace_break
signal/nds32: Remove tsk parameter from send_sigtrap
signal/riscv: Remove tsk parameter from do_trap
signal/sh: Remove tsk parameter from force_sig_info_fault
signal/um: Remove task parameter from send_sigtrap
signal/x86: Remove task parameter from send_sigtrap
signal: Remove task parameter from force_sig_mceerr
signal: Remove task parameter from force_sig
signal: Remove task parameter from force_sigsegv
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- rwsem scalability improvements, phase #2, by Waiman Long, which are
rather impressive:
"On a 2-socket 40-core 80-thread Skylake system with 40 reader
and writer locking threads, the min/mean/max locking operations
done in a 5-second testing window before the patchset were:
40 readers, Iterations Min/Mean/Max = 1,807/1,808/1,810
40 writers, Iterations Min/Mean/Max = 1,807/50,344/151,255
After the patchset, they became:
40 readers, Iterations Min/Mean/Max = 30,057/31,359/32,741
40 writers, Iterations Min/Mean/Max = 94,466/95,845/97,098"
There's a lot of changes to the locking implementation that makes
it similar to qrwlock, including owner handoff for more fair
locking.
Another microbenchmark shows how across the spectrum the
improvements are:
"With a locking microbenchmark running on 5.1 based kernel, the
total locking rates (in kops/s) on a 2-socket Skylake system
with equal numbers of readers and writers (mixed) before and
after this patchset were:
# of Threads Before Patch After Patch
------------ ------------ -----------
2 2,618 4,193
4 1,202 3,726
8 802 3,622
16 729 3,359
32 319 2,826
64 102 2,744"
The changes are extensive and the patch-set has been through
several iterations addressing various locking workloads. There
might be more regressions, but unless they are pathological I
believe we want to use this new implementation as the baseline
going forward.
- jump-label optimizations by Daniel Bristot de Oliveira: the primary
motivation was to remove IPI disturbance of isolated RT-workload
CPUs, which resulted in the implementation of batched jump-label
updates. Beyond the improvement of the real-time characteristics
kernel, in one test this patchset improved static key update
overhead from 57 msecs to just 1.4 msecs - which is a nice speedup
as well.
- atomic64_t cross-arch type cleanups by Mark Rutland: over the last
~10 years of atomic64_t existence the various types used by the
APIs only had to be self-consistent within each architecture -
which means they became wildly inconsistent across architectures.
Mark puts and end to this by reworking all the atomic64
implementations to use 's64' as the base type for atomic64_t, and
to ensure that this type is consistently used for parameters and
return values in the API, avoiding further problems in this area.
- A large set of small improvements to lockdep by Yuyang Du: type
cleanups, output cleanups, function return type and othr cleanups
all around the place.
- A set of percpu ops cleanups and fixes by Peter Zijlstra.
- Misc other changes - please see the Git log for more details"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (82 commits)
locking/lockdep: increase size of counters for lockdep statistics
locking/atomics: Use sed(1) instead of non-standard head(1) option
locking/lockdep: Move mark_lock() inside CONFIG_TRACE_IRQFLAGS && CONFIG_PROVE_LOCKING
x86/jump_label: Make tp_vec_nr static
x86/percpu: Optimize raw_cpu_xchg()
x86/percpu, sched/fair: Avoid local_clock()
x86/percpu, x86/irq: Relax {set,get}_irq_regs()
x86/percpu: Relax smp_processor_id()
x86/percpu: Differentiate this_cpu_{}() and __this_cpu_{}()
locking/rwsem: Guard against making count negative
locking/rwsem: Adaptive disabling of reader optimistic spinning
locking/rwsem: Enable time-based spinning on reader-owned rwsem
locking/rwsem: Make rwsem->owner an atomic_long_t
locking/rwsem: Enable readers spinning on writer
locking/rwsem: Clarify usage of owner's nonspinaable bit
locking/rwsem: Wake up almost all readers in wait queue
locking/rwsem: More optimal RT task handling of null owner
locking/rwsem: Always release wait_lock before waking up tasks
locking/rwsem: Implement lock handoff to prevent lock starvation
locking/rwsem: Make rwsem_spin_on_owner() return owner state
...
|
|
Commit 66d0d5a854a6 ("riscv: bpf: eliminate zero extension code-gen")
added the new zero-extension optimization for some BPF ALU operations.
Since then, bugs in the JIT that have been fixed in the bpf tree require
this optimization to be added to other operations: commit 1e692f09e091
("bpf, riscv: clear high 32 bits for ALU32 add/sub/neg/lsh/rsh/arsh"),
and commit fe121ee531d1 ("bpf, riscv: clear target register high 32-bits
for and/or/xor on ALU32").
Now that these have been merged to bpf-next, the zext optimization can
be enabled for the fixed operations.
Signed-off-by: Luke Nelson <luke.r.nels@gmail.com>
Cc: Song Liu <liu.song.a23@gmail.com>
Cc: Jiong Wang <jiong.wang@netronome.com>
Cc: Xi Wang <xi.wang@gmail.com>
Acked-by: Björn Töpel <bjorn.topel@gmail.com>
Acked-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The RISC-V free_initrd_mem is identical to the default one, except
that it doesn't poison the freed memory. Remove it so that the
default implementations gets used instead.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Reading the count register clears the interrupt signal. Currently, the
count registers are read into 'regval' variable but the variable is
never used. Therefore remove it. V2 of this patch add comments to
justify the readl calls without checking the return value.
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
This patch implements both 4MB huge page support for 32bit kernel
and 2MB/1GB huge pages support for 64bit kernel.
Signed-off-by: Alexandre Ghiti <alex@ghiti.fr>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Currently, the setup_bootmem() reserves memory from RAM start to the
kernel end. This prevents us from exploring ways to use the RAM below
(or before) the kernel start hence this patch updates setup_bootmem()
to only reserve memory from the kernel start to the kernel end.
Suggested-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Enable SOC_SIFIVE so the default upstream config is bootable on the SiFive
Unleashed Board.
And have basic support for future boards based on the same SoC.
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
[paul.walmsley@sifive.com: updated to apply]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
On selection of SOC_SIFIVE select the corresponding platform drivers.
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Create a config option for building SiFive SoC specific resources
e.g. SiFive device tree, platform drivers...
Signed-off-by: Loys Ollivier <lollivier@baylibre.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Since commit a6c19dfe3994 ("arm64,ia64,ppc,s390,sh,tile,um,x86,mm:
remove default gate area"), which predates riscv's inclusion in
Linux by almost three years, the default behavior wrt the gate area
is sane. Remove riscv's gate area stubs.
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: linux-riscv@lists.infradead.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
This patch enables NO_HZ_IDLE (idle dynamic ticks) and HIGH_RES_TIMERS
(hrtimers) in RV32 and RV64 defconfigs.
Both of the above options are enabled by default for architectures
such as x86, ARM, and ARM64.
The idle dynamic ticks helps use save power by stopping timer ticks
when the system is idle whereas hrtimers is a much improved timer
subsystem compared to the old "timer wheel" based system.
This patch is tested on SiFive Unleashed board and QEMU Virt machine.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Fix the comment since vmalloc_fault doesn't reach
flush_tlb_fix_spurious_fault.
Signed-off-by: ShihPo Hung <shihpo.hung@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: linux-riscv@lists.infradead.org
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
As per the convention for any SOC device with external connection,
define only device DT node in SOC DTSi file with status = "disabled"
and enable device in Board DTS file with status = "okay"
Reported-by: Anup Patel <anup@brainfault.org>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Currently, riscv upstream defconfig doesn't let you boot
through userspace if rootfs is on the SD card.
Let's enable MMC & SPI drivers as well so that one can boot
to the user space using default config in upstream kernel.
While here, enable automatic mounting of devtmpfs to simplify
kernel testing with minimal root filesystems. (pjw)
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
[paul.walmsley@sifive.com: mention the DEVTMPFS_MOUNT change in the
patch description]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Just use the generic definitions.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
|
|
Minor SPDX change conflict.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull still more SPDX updates from Greg KH:
"Another round of SPDX updates for 5.2-rc6
Here is what I am guessing is going to be the last "big" SPDX update
for 5.2. It contains all of the remaining GPLv2 and GPLv2+ updates
that were "easy" to determine by pattern matching. The ones after this
are going to be a bit more difficult and the people on the spdx list
will be discussing them on a case-by-case basis now.
Another 5000+ files are fixed up, so our overall totals are:
Files checked: 64545
Files with SPDX: 45529
Compared to the 5.1 kernel which was:
Files checked: 63848
Files with SPDX: 22576
This is a huge improvement.
Also, we deleted another 20000 lines of boilerplate license crud,
always nice to see in a diffstat"
* tag 'spdx-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (65 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 507
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 506
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 505
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 504
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 503
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 502
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 501
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 499
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 498
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 497
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 496
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 495
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 491
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 490
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 489
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 488
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 487
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 486
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 485
...
|
|
Add an EDAC driver for SiFive SoCs. The initial version supports ECC
event monitoring and reporting through the EDAC framework for the SiFive
L2 cache controller. It registers for notifier events from the L2 cache
controller driver (arch/riscv/mm/sifive_l2_cache.c) for L2 ECC events.
[ bp: Massage commit message. ]
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: James Morse <james.morse@arm.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linux-riscv@lists.infradead.org
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: "Paul E. McKenney" <paulmck@linux.ibm.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: sachin.ghadi@sifive.com
Link: https://lkml.kernel.org/r/1557142026-15949-2-git-send-email-yash.shah@sifive.com
|
|
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Enrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Honestly all the conflicts were simple overlapping changes,
nothing really interesting to report.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"This contains fixes, defconfig, and DT data changes for the v5.2-rc
series.
The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU
doesn't enter an infinite page fault loop
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules
- A udelay() fix for RV32, fixing a miscomputation of the delay time
- Removal of deprecated smp_mb__*() barriers
This also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build"
* tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove unused barrier defines
riscv: mm: synchronize MMU after pte change
riscv: dts: add initial board data for the SiFive HiFive Unleashed
riscv: dts: add initial support for the SiFive FU540-C000 SoC
dt-bindings: riscv: convert cpu binding to json-schema
dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540
arch: riscv: add support for building DTB files from DT source data
riscv: Fix udelay in RV32.
riscv: export pm_power_off again
RISC-V: defconfig: enable clocks, serial console
|
|
They were introduced in commit fab957c11efe ("RISC-V: Atomic and
Locking Code") long after commit 2e39465abc4b ("locking: Remove
deprecated smp_mb__() barriers") removed the remnants of all previous
instances from the tree.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
[paul.walmsley@sifive.com: stripped spurious mbox header from patch
description; fixed commit references in patch header]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
|
|
Because RISC-V compliant implementations can cache invalid entries
in TLB, an SFENCE.VMA is necessary after changes to the page table.
This patch adds an SFENCE.vma for the vmalloc_fault path.
Signed-off-by: ShihPo Hung <shihpo.hung@sifive.com>
[paul.walmsley@sifive.com: reversed tab->whitespace conversion,
wrapped comment lines]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: linux-riscv@lists.infradead.org
Cc: stable@vger.kernel.org
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
