summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-04-18atl1c: wrong register used to stop TXQHuang, Xiong
function atl1c_stop_mac uses wrong register of REG_TWSI_CTRL to stop mac, replace it with REG_TXQ_CTRL. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove code related to rxq 1/2/3Huang, Xiong
remove code related to rxq 1/2/3 since multi-q not support. refine REG_RXQ_CTRL definition as well. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: split 2 32bit registers of TPD to 4 16bit registersHuang, Xiong
TPD producer/consumer index is 16bit wide. 16bit read/write reduce the dependency of the 2 tpd rings (hi and lo) rename reg(157C/1580) to keep name coninsistency. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove SMB/CMB DMA related codeHuang, Xiong
l1c & later chips don't support DMA for SMB. CMB is removed from hardware. reg(15C8) is used to trig interrupt by tpd threshold. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove VPD registerHuang, Xiong
VPD register is only used for L1(devid=PCI_DEVICE_ID_ATTANSIC_L1) to access external NV-memory. l1c & later chip doesn't use it any more. PHY 0/1 registers occupy the last 2 slots of the dump table. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove HDS registerHuang, Xiong
remove HDS register as it doesn't exist in hardware. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove multiple-RX-Q codeHuang, Xiong
the multiple-RX-Q in hardware doesn't work, all related register definition & code are removed. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: update author contact info & company/driver desciptionHuang, Xiong
replace unavailable email of the author since he left with a mail-list. update company info as well, Atheros was acquired by Qualcomm. insert "100" to driver description since it support 100M controller. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem Conflicts: drivers/net/wireless/iwlwifi/iwl-testmode.c include/net/nfc/nfc.h net/nfc/netlink.c net/wireless/nl80211.c
2012-04-18Merge tag 'batman-adv-for-davem' of git://git.open-mesh.org/linux-mergeDavid S. Miller
Included changes: * remove duplicated line in comment * add htons() invocation for tt_crc as suggested by Al Viro * OriGinator Message seqno initial value is now random * some cleanups and fixes
2012-04-18tipc: Factor out name publication code to a separate functionAllan Stephens
This is done so that it can be reused with differing publication lists, instead of being hard coded to the cluster publicaton list. Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-04-18tipc: introduce publication lists structAllan Stephens
There is currently a single list that is containing both cluster-scope and zone-scope publications, and the list count is a separate free floating variable. Create a struct to bind the count to the list, and to pave the way for factoring out the publications into zone/cluster/node scope. The current "publ_root" most matches what will be the cluster scope list, so it is named accordingly in this commit. Signed-off-by: Allan Stephens <allan.stephens@windriver.com> Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
2012-04-18batman-adv: skip the window protection test when the originator has no ↵Antonio Quartulli
neighbours When we receive an OGM from from a node for the first time, the last_real_seqno field of the orig_node structure has not been initialised yet. The value of this field is used to compute the current ogm-seqno window and therefore the protection mechanism will probably drop the packet due to an out-of-window error. To avoid this situation this patch adds a check to skip the window protection mechanism if no neighbour nodes have already been added. When the first neighbour node is added, the last_real_seqno field is initialised too. Reported-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: print OGM seq numbers as unsigned intAntonio Quartulli
OGM sequence numbers are declared as uint32_t and so they have to printed using %u instead of %d in order to avoid wrong representations. Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: use ETH_HLEN instead of sizeof(struct ethhdr)Antonio Quartulli
Instead of using sizeof(struct ethhdr) it is strongly recommended to use the kernel macro ETH_HLEN. This patch substitute each occurrence of the former expressione with the latter one. Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: mark existing ogm variables as batman ivMarek Lindner
The coming protocol changes also will have a part called "OGM". That makes it necessary to introduce a distinction in the code base. Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: rename BATMAN_OGM_LEN to BATMAN_OGM_HLENMarek Lindner
Using BATMAN_OGM_LEN leaves one with the impression that this is the full packet size which is not the case. Therefore the variable is renamed. Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: refactoring API: find generalized name for bat_ogm_init_primary ↵Marek Lindner
callback Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: handle routing code initialization properlyMarek Lindner
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: add iface_disable() callback to routing APIMarek Lindner
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: randomize initial seqno to avoid collisionMarek Lindner
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: refactoring API: find generalized name for bat_ogm_init callbackMarek Lindner
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: move ogm initialization into the proper functionMarek Lindner
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: remove duplicated line in commentAntonio Quartulli
Remove an accidentally added duplicated line in a function comment Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18batman-adv: convert the tt_crc to network orderAntonio Quartulli
Before sending out a TT_Request packet we must convert the tt_crc field value to network order (since it is 16bits long). Reported-by: Al Viro <viro@ZenIV.linux.org.uk> Signed-off-by: Antonio Quartulli <ordex@autistici.org>
2012-04-18net/core:Remove memleak reports by kmemleak_not_leak.majianpeng
Signed-off-by: majianpeng <majianpeng@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18net/ipv4:Remove two memleak reports by kmemleak_not_leak.majianpeng
Signed-off-by: majianpeng <majianpeng@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-17net: filter: remove unused cpu_off in sparc JITEric Dumazet
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-17dmfe: enforce consistent timing delay.françois romieu
The driver does not always use the same timing for what looks like the same operations. - DCR0 Use the same udelay everywhere for reset. Upper bound is 100 us. - DCR9 Use 5us delay for srom clock. 1us delay for phy_write_1bit (writes PHY_DATA_[01]) are not changed as they stay withing a 2,5MHz MDIO clock range. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Reviewed-by: Grant Grundler <grundler@parisc-linux.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-17net: filter: Fix some more small issues in sparc JIT.David S. Miller
Fix mixed space and tabs. Put bpf_jit_load_*[] externs into bpf_jit.h "while(0)" --> "while (0)" "COND (X)" --> "COND(X)" Document branch offset calculations, and bpf_error's return sequence. Document the reason we need to emit three nops between the %y register write and the divide instruction. Remove erroneous trailing semicolons from emit_read_y() and emit_write_y(). Based upon feedback from Sam Ravnborg. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-17net: filter: Fix some minor issues in sparc JIT.David S. Miller
Correct conventions comments. %o4 and %o5 were swapped, %g3 was not documented. Use r_TMP instead of r_SKB_DATA + r_OFF where possible in assembler stubs. Correct discussion of %o4 and %o5 in one of bpf_jit_compile()'s comments. Based upon feedback from Richard Mortimer. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-17mwifiex: corrections in timestamp related codeAmitkumar Karwar
We get two timing related fields for each bss from firmware in scan results. 1) timestamp - Actual timestamp information in probe response/beacon 2) network_tsf - firmware's TSF value at the time the beacon or probe response was received. Both are needed while associating by firmware. The patch takes care of following things. 1) We should pass "timestamp" to cfg80211_inform_bss(), but currently "network_tsf" is being provided. This error is corrected here. 2) Rename "network_tsf" to "fw_tsf" 3) Make use of u64 variable instead of an array of u8/u32 to save parsed "timestamp" information. 4) Use timestamp provided to stack in scan results using cfg80211_inform_bss() while associating. (bss->tsf) 5) Allocate space to save fw_tsf in "priv" of cfg80211_bss and retrieve it while associating. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17mwifiex: code cleanup in BSS handlingAmitkumar Karwar
Rearrange some code to save extra parameters to the functions. Signed-off-by: Amitkumar Karwar <akarwar@marvell.com> Signed-off-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17libertas USB: convert to asynchronous firmware loadingDaniel Drake
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17libertas SDIO: convert to asynchronous firmware loadingDaniel Drake
Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17libertas: add asynchronous firmware loading capabilityDaniel Drake
As described at http://article.gmane.org/gmane.linux.kernel.wireless.general/86084 libertas is taking a long time to load because it loads firmware during module loading. Add a new API for interface drivers to load their firmware asynchronously. The same semantics of the firmware table are followed like before. Interface drivers will be converted in follow-up patches, then we can remove the old, synchronous firmware loading function. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17libertas: harden-up exit pathsDaniel Drake
These simple sanity check avoids extra complexity in error paths when moving to asynchronous firmware loading (which means the device may fail to init some time after its creation). Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17libertas: Firmware loading simplificationsDaniel Drake
Remove the ability to pass module parameters with firmware filenames for USB and SDIO interfaces. Remove the ability to pass custom "user" filenames to lbs_get_firmware(). Remove the ability to reprogram internal device memory with a different firmware from the USB driver (we don't know of any users), and simplify the OLPC firmware loading quirk to simply placing the OLPC firmware at the top of the list (we don't know of any users other than OLPC). Move lbs_get_firmware() into its own file. These simplifications should have no real-life effect but make the upcoming transition to asynchronous firmware loading considerably less painful. Signed-off-by: Daniel Drake <dsd@laptop.org> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17rt2x00: Don't let mac80211 send a BAR when an AMPDU subframe failsAndreas Hartmann
There are connection stalls or very poor throughputs with rt2800 hardware using 802.11n in AP mode since patch "mac80211: retry sending failed BAR frames later instead of tearing down aggr"[1][2]. Since rt2800 hardware is not able to correctly report the tx status of BAR frames, this patch removes as workaround the existing error handling on AP side, which lets mac80211 send a BAR when an AMPDU subframe fails. As a result, most wifi clients (aside from Intel STAs on Windows) instead will timeout now the reorder buffer and request the lost frame again. The correct solution would be, to tear down BA session on AP side. This patch was born on the basis of "[RFT] rt2x00: Tear down BA session on QoS frame failure"[3]. Thanks to Helmut Schaa for his support! [1] http://thread.gmane.org/gmane.linux.kernel.wireless.general/83297/focus=83304 [2] http://git.kernel.org/?p=linux/kernel/git/linville/wireless-testing.git;a=commit;h=f0425beda4d404a6e751439b562100b902ba9c98 [3] http://thread.gmane.org/gmane.linux.drivers.rt2x00.user/569 Signed-off-by: Andreas Hartmann <andihartmann@01019freenet.de> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17ath9k: use ath9k_hw_fbin2freq instead of FBIN2FREQGabor Juhos
The FBIN2FREQ macro and the ath9k_hw_fbin2freq function does the same thing. Remove the macro, and use the inline function instead. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17ath9k: move ath9k_hw_fbin2freq function to eeprom.hGabor Juhos
Both eeprom.c and ar9003_eeprom.c has an indentical 'ath9k_hw_fbin2freq' function. Move the function to a common place and remove the duplicates. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17ath9k: remove unused PWRINC_*_TO_*_CHAIN definesGabor Juhos
Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17ath9k: merge power correction constantsGabor Juhos
The existing constants are used for reduction/increase tx power level on devices with 2x2 and 3x3 chainmask. Both reduction and increase must use the same value, so it makes no sense to use separate constants for them. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17drivers/net/wireless/libertas/if_usb.c: add missing debugging codeJulia Lawall
Add a corresponding leave call on error failure. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Acked-by: Dan Williams <dcbw@redhat.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-04-17r8169: support the new RTL8411 chip.Hayes Wang
Compared with previous chipsets, it needs no special action trough the jumbo{enable/disable} helpers to operate with jumbo frames. Signed-off-by: Hayes Wang <hayeswang@realtek.com> Acked-by: Francois Romieu <romieu@fr.zoreil.com>
2012-04-17r8169: adjust some functions of 8111fHayes Wang
Put some settings of 8111f into one function which may be reused. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2012-04-17r8169: support the new RTL8402 chip.Hayes Wang
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2012-04-17r8169: add device specific CSI access helpers.Hayes Wang
New chipsets need it. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2012-04-17r8169: modify pll power functionHayes Wang
Adjust r810x_pll_power_down, r810x_pll_power_up, and r8168_pll_power_up. Always power up device during rtl_open. For r810x, turn off more power when the WOL is disabled. Signed-off-by: Hayes Wang <hayeswang@realtek.com>
2012-04-17r8169: 8168c and later require bit 0x20 to be set in Config2 for PME signaling.Francois Romieu
The new 84xx stopped flying below the radars. Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Hayes Wang <hayeswang@realtek.com>
generated by cgit v1.2.3-58-ga151 (git 2.39.0) at 2024-11-25 10:31:35 +0000