blob: 0775c16e0ec8062cbf77cc3b4bfc4d7540005592 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
|
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Device Tree file for Globalscale Marvell ESPRESSOBin Board
* Copyright (C) 2016 Marvell
*
* Romain Perier <romain.perier@free-electrons.com>
*
*/
#include <dt-bindings/gpio/gpio.h>
#include "armada-372x.dtsi"
/ {
aliases {
ethernet0 = ð0;
/* for dsa slave device */
ethernet1 = &switch0port1;
ethernet2 = &switch0port2;
ethernet3 = &switch0port3;
serial0 = &uart0;
serial1 = &uart1;
};
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
};
vcc_sd_reg1: regulator {
compatible = "regulator-gpio";
regulator-name = "vcc_sd1";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
regulator-boot-on;
gpios = <&gpionb 4 GPIO_ACTIVE_HIGH>;
gpios-states = <0>;
states = <1800000 0x1
3300000 0x0>;
enable-active-high;
};
};
/* J9 */
&pcie0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
};
/* J6 */
&sata {
status = "okay";
phys = <&comphy2 0>;
phy-names = "sata-phy";
};
/* J1 */
&sdhci1 {
wp-inverted;
bus-width = <4>;
cd-gpios = <&gpionb 3 GPIO_ACTIVE_LOW>;
marvell,pad-type = "sd";
vqmmc-supply = <&vcc_sd_reg1>;
pinctrl-names = "default";
pinctrl-0 = <&sdio_pins>;
status = "okay";
};
&spi0 {
status = "okay";
flash@0 {
reg = <0>;
compatible = "jedec,spi-nor";
spi-max-frequency = <104000000>;
m25p,fast-read;
};
};
/* Exported on the micro USB connector J5 through an FTDI */
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "okay";
};
/*
* Connector J17 and J18 expose a number of different features. Some pins are
* multiplexed. This is the case for instance for the following features:
* - UART1 (pin 24 = RX, pin 26 = TX). See armada-3720-db.dts for an example of
* how to enable it. Beware that the signals are 1.8V TTL.
* - I2C
* - SPI
* - MMC
*/
/* J7 */
&usb3 {
status = "okay";
};
/* J8 */
&usb2 {
status = "okay";
};
&mdio {
switch0: switch0@1 {
compatible = "marvell,mv88e6085";
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
dsa,member = <0 0>;
ports {
#address-cells = <1>;
#size-cells = <0>;
switch0port0: port@0 {
reg = <0>;
label = "cpu";
ethernet = <ð0>;
phy-mode = "rgmii-id";
fixed-link {
speed = <1000>;
full-duplex;
};
};
switch0port1: port@1 {
reg = <1>;
label = "wan";
phy-handle = <&switch0phy0>;
};
switch0port2: port@2 {
reg = <2>;
label = "lan0";
phy-handle = <&switch0phy1>;
};
switch0port3: port@3 {
reg = <3>;
label = "lan1";
phy-handle = <&switch0phy2>;
};
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
switch0phy0: switch0phy0@11 {
reg = <0x11>;
};
switch0phy1: switch0phy1@12 {
reg = <0x12>;
};
switch0phy2: switch0phy2@13 {
reg = <0x13>;
};
};
};
};
ð0 {
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
phy-mode = "rgmii-id";
status = "okay";
fixed-link {
speed = <1000>;
full-duplex;
};
};
|
