blob: e47c7ccc57f11ec53fe9aa5eb28b4c48e6397a27 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
|
Texas Instruments VPIF
----------------------
The TI Video Port InterFace (VPIF) is the primary component for video
capture and display on the DA850/AM18x family of TI DaVinci/Sitara
SoCs.
TI Document reference: SPRUH82C, Chapter 35
http://www.ti.com/lit/pdf/spruh82
Required properties:
- compatible: must be "ti,da850-vpif"
- reg: physical base address and length of the registers set for the device;
- interrupts: should contain IRQ line for the VPIF
Video Capture:
VPIF has a 16-bit parallel bus input, supporting 2 8-bit channels or a
single 16-bit channel. It should contain one or two port child nodes
with child 'endpoint' node. If there are two ports then port@0 must
describe the input and port@1 output channels. Please refer to the
bindings defined in
Documentation/devicetree/bindings/media/video-interfaces.txt.
Example using 2 8-bit input channels, one of which is connected to an
I2C-connected TVP5147 decoder:
vpif: vpif@217000 {
compatible = "ti,da850-vpif";
reg = <0x217000 0x1000>;
interrupts = <92>;
port@0 {
vpif_input_ch0: endpoint@0 {
reg = <0>;
bus-width = <8>;
remote-endpoint = <&composite_in>;
};
vpif_input_ch1: endpoint@1 {
reg = <1>;
bus-width = <8>;
data-shift = <8>;
};
};
port@1 {
vpif_output_ch0: endpoint {
bus-width = <8>;
remote-endpoint = <&composite_out>;
};
};
};
[ ... ]
&i2c0 {
tvp5147@5d {
compatible = "ti,tvp5147";
reg = <0x5d>;
port {
composite_in: endpoint {
hsync-active = <1>;
vsync-active = <1>;
pclk-sample = <0>;
/* VPIF channel 0 (lower 8-bits) */
remote-endpoint = <&vpif_input_ch0>;
bus-width = <8>;
};
};
};
adv7343@2a {
compatible = "adi,adv7343";
reg = <0x2a>;
port {
composite_out: endpoint {
adi,dac-enable = <1 1 1>;
adi,sd-dac-enable = <1>;
remote-endpoint = <&vpif_output_ch0>;
bus-width = <8>;
};
};
};
};
Alternatively, an example when the bus is configured as a single
16-bit input (e.g. for raw-capture mode):
vpif: vpif@217000 {
compatible = "ti,da850-vpif";
reg = <0x217000 0x1000>;
interrupts = <92>;
port {
vpif_ch0: endpoint {
bus-width = <16>;
};
};
};
|
