1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/clock/idt,versaclock5.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Binding for IDT VersaClock 5 and 6 programmable I2C clock generators
description: |
The IDT VersaClock 5 and VersaClock 6 are programmable I2C
clock generators providing from 3 to 12 output clocks.
When referencing the provided clock in the DT using phandle and clock
specifier, the following mapping applies:
- 5P49V5923:
0 -- OUT0_SEL_I2CB
1 -- OUT1
2 -- OUT2
- 5P49V5933:
0 -- OUT0_SEL_I2CB
1 -- OUT1
2 -- OUT4
- other parts:
0 -- OUT0_SEL_I2CB
1 -- OUT1
2 -- OUT2
3 -- OUT3
4 -- OUT4
The idt,shutdown and idt,output-enable-active properties control the
SH (en_global_shutdown) and SP bits of the Primary Source and Shutdown
Register, respectively. Their behavior is summarized by the following
table:
SH SP Output when the SD/OE pin is Low/High
== == =====================================
0 0 Active/Inactive
0 1 Inactive/Active
1 0 Active/Shutdown
1 1 Inactive/Shutdown
The case where SH and SP are both 1 is likely not very interesting.
maintainers:
- Luca Ceresoli <luca.ceresoli@bootlin.com>
properties:
compatible:
enum:
- idt,5p49v5923
- idt,5p49v5925
- idt,5p49v5933
- idt,5p49v5935
- idt,5p49v6901
- idt,5p49v6965
reg:
description: I2C device address
enum: [ 0x68, 0x6a ]
'#clock-cells':
const: 1
clock-names:
minItems: 1
maxItems: 2
items:
enum: [ xin, clkin ]
clocks:
minItems: 1
maxItems: 2
idt,xtal-load-femtofarads:
minimum: 9000
maximum: 22760
description: Optional load capacitor for XTAL1 and XTAL2
idt,shutdown:
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1]
description: |
If 1, this enables the shutdown functionality: the chip will be
shut down if the SD/OE pin is driven high. If 0, this disables the
shutdown functionality: the chip will never be shut down based on
the value of the SD/OE pin. This property corresponds to the SH
bit of the Primary Source and Shutdown Register.
idt,output-enable-active:
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1]
description: |
If 1, this enables output when the SD/OE pin is high, and disables
output when the SD/OE pin is low. If 0, this disables output when
the SD/OE pin is high, and enables output when the SD/OE pin is
low. This corresponds to the SP bit of the Primary Source and
Shutdown Register.
patternProperties:
"^OUT[1-4]$":
type: object
description:
Description of one of the outputs (OUT1..OUT4). See "Clock1 Output
Configuration" in the Versaclock 5/6/6E Family Register Description
and Programming Guide.
properties:
idt,mode:
description:
The output drive mode. Values defined in dt-bindings/clk/versaclock.h
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 6
idt,voltage-microvolt:
description: The output drive voltage.
enum: [ 1800000, 2500000, 3300000 ]
idt,slew-percent:
description: The Slew rate control for CMOS single-ended.
enum: [ 80, 85, 90, 100 ]
additionalProperties: false
required:
- compatible
- reg
- '#clock-cells'
- idt,shutdown
- idt,output-enable-active
allOf:
- if:
properties:
compatible:
enum:
- idt,5p49v5933
- idt,5p49v5935
then:
# Devices with builtin crystal + optional external input
properties:
clock-names:
const: clkin
clocks:
maxItems: 1
else:
# Devices without builtin crystal
required:
- clock-names
- clocks
additionalProperties: false
examples:
- |
#include <dt-bindings/clk/versaclock.h>
/* 25MHz reference crystal */
ref25: ref25m {
compatible = "fixed-clock";
#clock-cells = <0>;
clock-frequency = <25000000>;
};
i2c@0 {
reg = <0x0 0x100>;
#address-cells = <1>;
#size-cells = <0>;
/* IDT 5P49V5923 I2C clock generator */
vc5: clock-generator@6a {
compatible = "idt,5p49v5923";
reg = <0x6a>;
#clock-cells = <1>;
/* Connect XIN input to 25MHz reference */
clocks = <&ref25m>;
clock-names = "xin";
/* Set the SD/OE pin's settings */
idt,shutdown = <0>;
idt,output-enable-active = <0>;
OUT1 {
idt,mode = <VC5_CMOSD>;
idt,voltage-microvolt = <1800000>;
idt,slew-percent = <80>;
};
OUT4 {
idt,mode = <VC5_LVDS>;
};
};
};
...
|
