From f2654a4781318dc7ab8d6cde66f1fa39eab980a9 Mon Sep 17 00:00:00 2001 From: Fahad Kunnathadi Date: Fri, 15 Sep 2017 12:01:58 +0530 Subject: net: phy: Fix mask value write on gmii2rgmii converter speed register To clear Speed Selection in MDIO control register(0x10), ie, clear bits 6 and 13 to zero while keeping other bits same. Before AND operation,The Mask value has to be perform with bitwise NOT operation (ie, ~ operator) This patch clears current speed selection before writing the new speed settings to gmii2rgmii converter Fixes: f411a6160bd4 ("net: phy: Add gmiitorgmii converter support") Signed-off-by: Fahad Kunnathadi Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- drivers/net/phy/xilinx_gmii2rgmii.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/phy/xilinx_gmii2rgmii.c b/drivers/net/phy/xilinx_gmii2rgmii.c index d15dd3938ba8..2e5150b0b8d5 100644 --- a/drivers/net/phy/xilinx_gmii2rgmii.c +++ b/drivers/net/phy/xilinx_gmii2rgmii.c @@ -44,7 +44,7 @@ static int xgmiitorgmii_read_status(struct phy_device *phydev) priv->phy_drv->read_status(phydev); val = mdiobus_read(phydev->mdio.bus, priv->addr, XILINX_GMII2RGMII_REG); - val &= XILINX_GMII2RGMII_SPEED_MASK; + val &= ~XILINX_GMII2RGMII_SPEED_MASK; if (phydev->speed == SPEED_1000) val |= BMCR_SPEED1000; -- cgit v1.2.3-58-ga151 From 1e3c5ec66119783440ed211ae527674651affa9b Mon Sep 17 00:00:00 2001 From: Sathya Perla Date: Mon, 18 Sep 2017 17:05:37 +0530 Subject: bnxt_en: check for ingress qdisc in flower offload Check for ingress-only qdisc for flower offload, as other qdiscs are not supported for flower offload. Suggested-by: Jiri Pirko Signed-off-by: Sathya Perla Reviewed-by: Jiri Pirko Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c b/drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c index ccd699fb2d70..7dd3d131043a 100644 --- a/drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c +++ b/drivers/net/ethernet/broadcom/bnxt/bnxt_tc.c @@ -750,6 +750,10 @@ int bnxt_tc_setup_flower(struct bnxt *bp, u16 src_fid, { int rc = 0; + if (!is_classid_clsact_ingress(cls_flower->common.classid) || + cls_flower->common.chain_index) + return -EOPNOTSUPP; + switch (cls_flower->command) { case TC_CLSFLOWER_REPLACE: rc = bnxt_tc_add_flow(bp, src_fid, cls_flower); -- cgit v1.2.3-58-ga151 From 129c6cda2de2a8ac44fab096152469999b727faf Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Mon, 18 Sep 2017 13:03:43 -0700 Subject: 8139too: revisit napi_complete_done() usage MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit It seems we have to be more careful in napi_complete_done() use. This patch is not a revert, as it seems we can avoid bug that Ville reported by moving the napi_complete_done() test in the spinlock section. Many thanks to Ville for detective work and all tests. Fixes: 617f01211baf ("8139too: use napi_complete_done()") Reported-by: Ville Syrjälä Tested-by: Ville Syrjälä Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/8139too.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/realtek/8139too.c b/drivers/net/ethernet/realtek/8139too.c index ca22f2898664..d24b47b8e0b2 100644 --- a/drivers/net/ethernet/realtek/8139too.c +++ b/drivers/net/ethernet/realtek/8139too.c @@ -2135,11 +2135,12 @@ static int rtl8139_poll(struct napi_struct *napi, int budget) if (likely(RTL_R16(IntrStatus) & RxAckBits)) work_done += rtl8139_rx(dev, tp, budget); - if (work_done < budget && napi_complete_done(napi, work_done)) { + if (work_done < budget) { unsigned long flags; spin_lock_irqsave(&tp->lock, flags); - RTL_W16_F(IntrMask, rtl8139_intr_mask); + if (napi_complete_done(napi, work_done)) + RTL_W16_F(IntrMask, rtl8139_intr_mask); spin_unlock_irqrestore(&tp->lock, flags); } spin_unlock(&tp->rx_lock); -- cgit v1.2.3-58-ga151 From 8ecb1a29e11e24c458ee4ee59447d0ddf8274589 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Mon, 18 Sep 2017 16:31:30 -0700 Subject: net: systemport: Fix 64-bit statistics dependency There are several problems with commit 10377ba7673d ("net: systemport: Support 64bit statistics", first one got fixed in 7095c973453e ("net: systemport: Fix 64-bit stats deadlock"). The second problem is that this specific code updates the stats64.tx_{packets,bytes} from ndo_get_stats64() and that is what we are returning to ethtool -S. If we are not running a tool that involves calling ndo_get_stats64(), then we won't get updated ethtool stats. The solution to this is to update the stats from both call sites, factoring that into a specific function, While at it, don't just check the sizeof() but also the type of the statistics in order to use the 64-bit stats seqlock. Fixes: 10377ba7673d ("net: systemport: Support 64bit statistics") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bcmsysport.c | 52 ++++++++++++++++++------------ 1 file changed, 32 insertions(+), 20 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/broadcom/bcmsysport.c b/drivers/net/ethernet/broadcom/bcmsysport.c index c3c53f6cd9e6..83eec9a8c275 100644 --- a/drivers/net/ethernet/broadcom/bcmsysport.c +++ b/drivers/net/ethernet/broadcom/bcmsysport.c @@ -432,6 +432,27 @@ static void bcm_sysport_update_mib_counters(struct bcm_sysport_priv *priv) netif_dbg(priv, hw, priv->netdev, "updated MIB counters\n"); } +static void bcm_sysport_update_tx_stats(struct bcm_sysport_priv *priv, + u64 *tx_bytes, u64 *tx_packets) +{ + struct bcm_sysport_tx_ring *ring; + u64 bytes = 0, packets = 0; + unsigned int start; + unsigned int q; + + for (q = 0; q < priv->netdev->num_tx_queues; q++) { + ring = &priv->tx_rings[q]; + do { + start = u64_stats_fetch_begin_irq(&priv->syncp); + bytes = ring->bytes; + packets = ring->packets; + } while (u64_stats_fetch_retry_irq(&priv->syncp, start)); + + *tx_bytes += bytes; + *tx_packets += packets; + } +} + static void bcm_sysport_get_stats(struct net_device *dev, struct ethtool_stats *stats, u64 *data) { @@ -439,11 +460,16 @@ static void bcm_sysport_get_stats(struct net_device *dev, struct bcm_sysport_stats64 *stats64 = &priv->stats64; struct u64_stats_sync *syncp = &priv->syncp; struct bcm_sysport_tx_ring *ring; + u64 tx_bytes = 0, tx_packets = 0; unsigned int start; int i, j; - if (netif_running(dev)) + if (netif_running(dev)) { bcm_sysport_update_mib_counters(priv); + bcm_sysport_update_tx_stats(priv, &tx_bytes, &tx_packets); + stats64->tx_bytes = tx_bytes; + stats64->tx_packets = tx_packets; + } for (i = 0, j = 0; i < BCM_SYSPORT_STATS_LEN; i++) { const struct bcm_sysport_stats *s; @@ -461,12 +487,13 @@ static void bcm_sysport_get_stats(struct net_device *dev, continue; p += s->stat_offset; - if (s->stat_sizeof == sizeof(u64)) + if (s->stat_sizeof == sizeof(u64) && + s->type == BCM_SYSPORT_STAT_NETDEV64) { do { start = u64_stats_fetch_begin_irq(syncp); data[i] = *(u64 *)p; } while (u64_stats_fetch_retry_irq(syncp, start)); - else + } else data[i] = *(u32 *)p; j++; } @@ -1716,27 +1743,12 @@ static void bcm_sysport_get_stats64(struct net_device *dev, { struct bcm_sysport_priv *priv = netdev_priv(dev); struct bcm_sysport_stats64 *stats64 = &priv->stats64; - struct bcm_sysport_tx_ring *ring; - u64 tx_packets = 0, tx_bytes = 0; unsigned int start; - unsigned int q; netdev_stats_to_stats64(stats, &dev->stats); - for (q = 0; q < dev->num_tx_queues; q++) { - ring = &priv->tx_rings[q]; - do { - start = u64_stats_fetch_begin_irq(&priv->syncp); - tx_bytes = ring->bytes; - tx_packets = ring->packets; - } while (u64_stats_fetch_retry_irq(&priv->syncp, start)); - - stats->tx_bytes += tx_bytes; - stats->tx_packets += tx_packets; - } - - stats64->tx_bytes = stats->tx_bytes; - stats64->tx_packets = stats->tx_packets; + bcm_sysport_update_tx_stats(priv, &stats->tx_bytes, + &stats->tx_packets); do { start = u64_stats_fetch_begin_irq(&priv->syncp); -- cgit v1.2.3-58-ga151 From 6073512cc8e2c48bed5c6625c02c5e4ae50cec34 Mon Sep 17 00:00:00 2001 From: Jerome Brunet Date: Mon, 18 Sep 2017 14:59:20 +0200 Subject: net: phy: Kconfig: Fix PHY infrastructure menu in menuconfig Since the integration of PHYLINK, the configuration option which used to be under the PHY infrastructure menu in menuconfig ended up one level up (the network device driver section) By placing PHYLINK option right after PHYLIB entry, it broke the way Kconfig used to build the menu. See kconfig-language.txt, section "Menu structure", 2nd method. This is fixed by placing the PHYLINK option just before PHYLIB. Fixes: 9525ae83959b ("phylink: add phylink infrastructure") Signed-off-by: Jerome Brunet Signed-off-by: David S. Miller --- drivers/net/phy/Kconfig | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig index a9d16a3af514..cd931cf9dcc2 100644 --- a/drivers/net/phy/Kconfig +++ b/drivers/net/phy/Kconfig @@ -160,15 +160,6 @@ config MDIO_XGENE endif -menuconfig PHYLIB - tristate "PHY Device support and infrastructure" - depends on NETDEVICES - select MDIO_DEVICE - help - Ethernet controllers are usually attached to PHY - devices. This option provides infrastructure for - managing PHY devices. - config PHYLINK tristate depends on NETDEVICES @@ -179,6 +170,15 @@ config PHYLINK configuration links, PHYs, and Serdes links with MAC level autonegotiation modes. +menuconfig PHYLIB + tristate "PHY Device support and infrastructure" + depends on NETDEVICES + select MDIO_DEVICE + help + Ethernet controllers are usually attached to PHY + devices. This option provides infrastructure for + managing PHY devices. + if PHYLIB config SWPHY -- cgit v1.2.3-58-ga151 From 2a4776e14f7da3d48fffb4edbb82355742f23478 Mon Sep 17 00:00:00 2001 From: Lipeng Date: Tue, 19 Sep 2017 17:17:10 +0100 Subject: net: hns3: Fixes initialization of phy address from firmware Default phy address of every port is 0. Therefore, phy address for each port need to be fetched from firmware and device initialized with fetched non-default phy address. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Lipeng Signed-off-by: Salil Mehta Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index bb45365fb817..db4e07dac29a 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -1066,6 +1066,7 @@ static int hclge_configure(struct hclge_dev *hdev) for (i = 0; i < ETH_ALEN; i++) hdev->hw.mac.mac_addr[i] = cfg.mac_addr[i]; hdev->hw.mac.media_type = cfg.media_type; + hdev->hw.mac.phy_addr = cfg.phy_addr; hdev->num_desc = cfg.tqp_desc_num; hdev->tm_info.num_pg = 1; hdev->tm_info.num_tc = cfg.tc_num; -- cgit v1.2.3-58-ga151 From c5b1b97522ef32d2170c9aa1a0c1eec179acbb3a Mon Sep 17 00:00:00 2001 From: Lipeng Date: Tue, 19 Sep 2017 17:17:11 +0100 Subject: net: hns3: Fixes the command used to unmap ring from vector This patch fixes the IMP command being used to unmap the vector from the corresponding ring. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Lipeng Signed-off-by: Salil Mehta Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index db4e07dac29a..e324bc6e9f4f 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -2779,7 +2779,7 @@ static int hclge_unmap_ring_from_vector( } i = 0; hclge_cmd_setup_basic_desc(&desc, - HCLGE_OPC_ADD_RING_TO_VECTOR, + HCLGE_OPC_DEL_RING_TO_VECTOR, false); req->int_vector_id = vector_id; } -- cgit v1.2.3-58-ga151 From 0305b443a3ba5b84aa474786026df04a70460135 Mon Sep 17 00:00:00 2001 From: Lipeng Date: Tue, 19 Sep 2017 17:17:12 +0100 Subject: net: hns3: Fixes ring-to-vector map-and-unmap command This patch fixes the vector-to-ring map and unmap command and adds INT_GL(for, Gap Limiting Interrupts) and VF id to it as required by the hardware interface. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Lipeng Signed-off-by: Mingguang Qu Signed-off-by: Salil Mehta Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h | 8 ++++++-- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 8 ++++++++ 2 files changed, 14 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h index 91ae0135ee50..c2b613b40509 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h @@ -238,7 +238,7 @@ struct hclge_tqp_map { u8 rsv[18]; }; -#define HCLGE_VECTOR_ELEMENTS_PER_CMD 11 +#define HCLGE_VECTOR_ELEMENTS_PER_CMD 10 enum hclge_int_type { HCLGE_INT_TX, @@ -252,8 +252,12 @@ struct hclge_ctrl_vector_chain { #define HCLGE_INT_TYPE_S 0 #define HCLGE_INT_TYPE_M 0x3 #define HCLGE_TQP_ID_S 2 -#define HCLGE_TQP_ID_M (0x3fff << HCLGE_TQP_ID_S) +#define HCLGE_TQP_ID_M (0x7ff << HCLGE_TQP_ID_S) +#define HCLGE_INT_GL_IDX_S 13 +#define HCLGE_INT_GL_IDX_M (0x3 << HCLGE_INT_GL_IDX_S) __le16 tqp_type_and_id[HCLGE_VECTOR_ELEMENTS_PER_CMD]; + u8 vfid; + u8 rsv; }; #define HCLGE_TC_NUM 8 diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index e324bc6e9f4f..eafd9c678162 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -2680,7 +2680,11 @@ int hclge_map_vport_ring_to_vector(struct hclge_vport *vport, int vector_id, hnae_get_bit(node->flag, HNAE3_RING_TYPE_B)); hnae_set_field(req->tqp_type_and_id[i], HCLGE_TQP_ID_M, HCLGE_TQP_ID_S, node->tqp_index); + hnae_set_field(req->tqp_type_and_id[i], HCLGE_INT_GL_IDX_M, + HCLGE_INT_GL_IDX_S, + hnae_get_bit(node->flag, HNAE3_RING_TYPE_B)); req->tqp_type_and_id[i] = cpu_to_le16(req->tqp_type_and_id[i]); + req->vfid = vport->vport_id; if (++i >= HCLGE_VECTOR_ELEMENTS_PER_CMD) { req->int_cause_num = HCLGE_VECTOR_ELEMENTS_PER_CMD; @@ -2764,8 +2768,12 @@ static int hclge_unmap_ring_from_vector( hnae_get_bit(node->flag, HNAE3_RING_TYPE_B)); hnae_set_field(req->tqp_type_and_id[i], HCLGE_TQP_ID_M, HCLGE_TQP_ID_S, node->tqp_index); + hnae_set_field(req->tqp_type_and_id[i], HCLGE_INT_GL_IDX_M, + HCLGE_INT_GL_IDX_S, + hnae_get_bit(node->flag, HNAE3_RING_TYPE_B)); req->tqp_type_and_id[i] = cpu_to_le16(req->tqp_type_and_id[i]); + req->vfid = vport->vport_id; if (++i >= HCLGE_VECTOR_ELEMENTS_PER_CMD) { req->int_cause_num = HCLGE_VECTOR_ELEMENTS_PER_CMD; -- cgit v1.2.3-58-ga151 From 139e8792537b327252a9676591a78e6408d50a85 Mon Sep 17 00:00:00 2001 From: Lipeng Date: Tue, 19 Sep 2017 17:17:13 +0100 Subject: net: hns3: Fixes the initialization of MAC address in hardware This patch fixes the initialization of MAC address, fetched from HNS3 firmware i.e. when it is not randomly generated, to the HNS3 hardware. Fixes: ca60906d2795 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC") Signed-off-by: Lipeng Signed-off-by: Salil Mehta Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c index 1c3e29447891..4d68d6ea5143 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c @@ -2705,10 +2705,11 @@ static void hns3_init_mac_addr(struct net_device *netdev) eth_hw_addr_random(netdev); dev_warn(priv->dev, "using random MAC address %pM\n", netdev->dev_addr); - /* Also copy this new MAC address into hdev */ - if (h->ae_algo->ops->set_mac_addr) - h->ae_algo->ops->set_mac_addr(h, netdev->dev_addr); } + + if (h->ae_algo->ops->set_mac_addr) + h->ae_algo->ops->set_mac_addr(h, netdev->dev_addr); + } static void hns3_nic_set_priv_ops(struct net_device *netdev) -- cgit v1.2.3-58-ga151 From fbbb1536b220eb4f4f95cbceae6579489a8adad5 Mon Sep 17 00:00:00 2001 From: Salil Mehta Date: Tue, 19 Sep 2017 17:17:14 +0100 Subject: net: hns3: Fixes the ether address copy with appropriate API This patch replaces the ethernet address copy instance with more appropriate ether_addr_copy() function. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Salil Mehta Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index eafd9c678162..8e172afd4876 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -1063,8 +1063,7 @@ static int hclge_configure(struct hclge_dev *hdev) hdev->base_tqp_pid = 0; hdev->rss_size_max = 1; hdev->rx_buf_len = cfg.rx_buf_len; - for (i = 0; i < ETH_ALEN; i++) - hdev->hw.mac.mac_addr[i] = cfg.mac_addr[i]; + ether_addr_copy(hdev->hw.mac.mac_addr, cfg.mac_addr); hdev->hw.mac.media_type = cfg.media_type; hdev->hw.mac.phy_addr = cfg.phy_addr; hdev->num_desc = cfg.tqp_desc_num; -- cgit v1.2.3-58-ga151 From 5e43aef8491ae3b5feb79cd15260faf39303ef33 Mon Sep 17 00:00:00 2001 From: Lipeng Date: Tue, 19 Sep 2017 17:17:15 +0100 Subject: net: hns3: Fixes the default VLAN-id of PF When there is no vlan id in the packets, hardware will treat the vlan id as 0 and look for the mac_vlan table. This patch set the default vlan id of PF as 0. Without this config, it will fail when look for mac_vlan table, and hardware will drop packets. Fixes: 6427264ef330 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Mingguang Qu Signed-off-by: Lipeng Signed-off-by: Salil Mehta Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 8e172afd4876..74008ef23169 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -3673,6 +3673,7 @@ static int hclge_init_vlan_config(struct hclge_dev *hdev) { #define HCLGE_VLAN_TYPE_VF_TABLE 0 #define HCLGE_VLAN_TYPE_PORT_TABLE 1 + struct hnae3_handle *handle; int ret; ret = hclge_set_vlan_filter_ctrl(hdev, HCLGE_VLAN_TYPE_VF_TABLE, @@ -3682,8 +3683,11 @@ static int hclge_init_vlan_config(struct hclge_dev *hdev) ret = hclge_set_vlan_filter_ctrl(hdev, HCLGE_VLAN_TYPE_PORT_TABLE, true); + if (ret) + return ret; - return ret; + handle = &hdev->vport[0].nic; + return hclge_set_port_vlan_filter(handle, htons(ETH_P_8021Q), 0, false); } static int hclge_set_mtu(struct hnae3_handle *handle, int new_mtu) -- cgit v1.2.3-58-ga151 From 90f7b11a5a0081feb7041fcc795c9a131a62a725 Mon Sep 17 00:00:00 2001 From: Lipeng Date: Tue, 19 Sep 2017 17:17:16 +0100 Subject: net: hns3: Fixes the premature exit of loop when matching clients When register/unregister ae_dev, ae_dev should match all client in the client_list. Enet and roce can co-exists together so we should continue checking for enet and roce presence together. So break should not be there. Above caused problems in loading and unloading of modules. Fixes: 38eddd126772 ("net: hns3: Add support of the HNAE3 framework") Signed-off-by: Lipeng Signed-off-by: Salil Mehta Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hnae3.c | 43 ++++++----------------------- 1 file changed, 9 insertions(+), 34 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hnae3.c b/drivers/net/ethernet/hisilicon/hns3/hnae3.c index 59efbd605416..5bcb2238acb2 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hnae3.c +++ b/drivers/net/ethernet/hisilicon/hns3/hnae3.c @@ -37,20 +37,15 @@ static bool hnae3_client_match(enum hnae3_client_type client_type, } static int hnae3_match_n_instantiate(struct hnae3_client *client, - struct hnae3_ae_dev *ae_dev, - bool is_reg, bool *matched) + struct hnae3_ae_dev *ae_dev, bool is_reg) { int ret; - *matched = false; - /* check if this client matches the type of ae_dev */ if (!(hnae3_client_match(client->type, ae_dev->dev_type) && hnae_get_bit(ae_dev->flag, HNAE3_DEV_INITED_B))) { return 0; } - /* there is a match of client and dev */ - *matched = true; /* now, (un-)instantiate client by calling lower layer */ if (is_reg) { @@ -69,7 +64,6 @@ int hnae3_register_client(struct hnae3_client *client) { struct hnae3_client *client_tmp; struct hnae3_ae_dev *ae_dev; - bool matched; int ret = 0; mutex_lock(&hnae3_common_lock); @@ -86,7 +80,7 @@ int hnae3_register_client(struct hnae3_client *client) /* if the client could not be initialized on current port, for * any error reasons, move on to next available port */ - ret = hnae3_match_n_instantiate(client, ae_dev, true, &matched); + ret = hnae3_match_n_instantiate(client, ae_dev, true); if (ret) dev_err(&ae_dev->pdev->dev, "match and instantiation failed for port\n"); @@ -102,12 +96,11 @@ EXPORT_SYMBOL(hnae3_register_client); void hnae3_unregister_client(struct hnae3_client *client) { struct hnae3_ae_dev *ae_dev; - bool matched; mutex_lock(&hnae3_common_lock); /* un-initialize the client on every matched port */ list_for_each_entry(ae_dev, &hnae3_ae_dev_list, node) { - hnae3_match_n_instantiate(client, ae_dev, false, &matched); + hnae3_match_n_instantiate(client, ae_dev, false); } list_del(&client->node); @@ -124,7 +117,6 @@ int hnae3_register_ae_algo(struct hnae3_ae_algo *ae_algo) const struct pci_device_id *id; struct hnae3_ae_dev *ae_dev; struct hnae3_client *client; - bool matched; int ret = 0; mutex_lock(&hnae3_common_lock); @@ -151,13 +143,10 @@ int hnae3_register_ae_algo(struct hnae3_ae_algo *ae_algo) * initialize the figure out client instance */ list_for_each_entry(client, &hnae3_client_list, node) { - ret = hnae3_match_n_instantiate(client, ae_dev, true, - &matched); + ret = hnae3_match_n_instantiate(client, ae_dev, true); if (ret) dev_err(&ae_dev->pdev->dev, "match and instantiation failed\n"); - if (matched) - break; } } @@ -175,7 +164,6 @@ void hnae3_unregister_ae_algo(struct hnae3_ae_algo *ae_algo) const struct pci_device_id *id; struct hnae3_ae_dev *ae_dev; struct hnae3_client *client; - bool matched; mutex_lock(&hnae3_common_lock); /* Check if there are matched ae_dev */ @@ -187,12 +175,8 @@ void hnae3_unregister_ae_algo(struct hnae3_ae_algo *ae_algo) /* check the client list for the match with this ae_dev type and * un-initialize the figure out client instance */ - list_for_each_entry(client, &hnae3_client_list, node) { - hnae3_match_n_instantiate(client, ae_dev, false, - &matched); - if (matched) - break; - } + list_for_each_entry(client, &hnae3_client_list, node) + hnae3_match_n_instantiate(client, ae_dev, false); ae_algo->ops->uninit_ae_dev(ae_dev); hnae_set_bit(ae_dev->flag, HNAE3_DEV_INITED_B, 0); @@ -212,7 +196,6 @@ int hnae3_register_ae_dev(struct hnae3_ae_dev *ae_dev) const struct pci_device_id *id; struct hnae3_ae_algo *ae_algo; struct hnae3_client *client; - bool matched; int ret = 0; mutex_lock(&hnae3_common_lock); @@ -246,13 +229,10 @@ int hnae3_register_ae_dev(struct hnae3_ae_dev *ae_dev) * initialize the figure out client instance */ list_for_each_entry(client, &hnae3_client_list, node) { - ret = hnae3_match_n_instantiate(client, ae_dev, true, - &matched); + ret = hnae3_match_n_instantiate(client, ae_dev, true); if (ret) dev_err(&ae_dev->pdev->dev, "match and instantiation failed\n"); - if (matched) - break; } out_err: @@ -270,7 +250,6 @@ void hnae3_unregister_ae_dev(struct hnae3_ae_dev *ae_dev) const struct pci_device_id *id; struct hnae3_ae_algo *ae_algo; struct hnae3_client *client; - bool matched; mutex_lock(&hnae3_common_lock); /* Check if there are matched ae_algo */ @@ -279,12 +258,8 @@ void hnae3_unregister_ae_dev(struct hnae3_ae_dev *ae_dev) if (!id) continue; - list_for_each_entry(client, &hnae3_client_list, node) { - hnae3_match_n_instantiate(client, ae_dev, false, - &matched); - if (matched) - break; - } + list_for_each_entry(client, &hnae3_client_list, node) + hnae3_match_n_instantiate(client, ae_dev, false); ae_algo->ops->uninit_ae_dev(ae_dev); hnae_set_bit(ae_dev->flag, HNAE3_DEV_INITED_B, 0); -- cgit v1.2.3-58-ga151 From f55956065ec94e3e9371463d693a1029c4cc3007 Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Tue, 19 Sep 2017 19:35:18 +0200 Subject: net: emac: Fix napi poll list corruption This patch is pretty much a carbon copy of commit 3079c652141f ("caif: Fix napi poll list corruption") with "caif" replaced by "emac". The commit d75b1ade567f ("net: less interrupt masking in NAPI") breaks emac. It is now required that if the entire budget is consumed when poll returns, the napi poll_list must remain empty. However, like some other drivers emac tries to do a last-ditch check and if there is more work it will call napi_reschedule and then immediately process some of this new work. Should the entire budget be consumed while processing such new work then we will violate the new caller contract. This patch fixes this by not touching any work when we reschedule in emac. Signed-off-by: Christian Lamparter Signed-off-by: David S. Miller --- drivers/net/ethernet/ibm/emac/mal.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/ibm/emac/mal.c b/drivers/net/ethernet/ibm/emac/mal.c index 2c74baa2398a..fff09dcf9e34 100644 --- a/drivers/net/ethernet/ibm/emac/mal.c +++ b/drivers/net/ethernet/ibm/emac/mal.c @@ -402,7 +402,7 @@ static int mal_poll(struct napi_struct *napi, int budget) unsigned long flags; MAL_DBG2(mal, "poll(%d)" NL, budget); - again: + /* Process TX skbs */ list_for_each(l, &mal->poll_list) { struct mal_commac *mc = @@ -451,7 +451,6 @@ static int mal_poll(struct napi_struct *napi, int budget) spin_lock_irqsave(&mal->lock, flags); mal_disable_eob_irq(mal); spin_unlock_irqrestore(&mal->lock, flags); - goto again; } mc->ops->poll_tx(mc->dev); } -- cgit v1.2.3-58-ga151 From 5e62d98c4bbc243f3dca18e73a754b629839fc5c Mon Sep 17 00:00:00 2001 From: Troy Kisky Date: Tue, 19 Sep 2017 17:33:07 -0700 Subject: net: fec: only check queue 0 if RXF_0/TXF_0 interrupt is set Before queue 0 was always checked if any queue caused an interrupt. It is better to just mark queue 0 if queue 0 has caused an interrupt. Signed-off-by: Troy Kisky Acked-by: Fugang Duan Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c index 56f56d6ada9c..464055fb33d5 100644 --- a/drivers/net/ethernet/freescale/fec_main.c +++ b/drivers/net/ethernet/freescale/fec_main.c @@ -1559,14 +1559,14 @@ fec_enet_collect_events(struct fec_enet_private *fep, uint int_events) if (int_events == 0) return false; - if (int_events & FEC_ENET_RXF) + if (int_events & FEC_ENET_RXF_0) fep->work_rx |= (1 << 2); if (int_events & FEC_ENET_RXF_1) fep->work_rx |= (1 << 0); if (int_events & FEC_ENET_RXF_2) fep->work_rx |= (1 << 1); - if (int_events & FEC_ENET_TXF) + if (int_events & FEC_ENET_TXF_0) fep->work_tx |= (1 << 2); if (int_events & FEC_ENET_TXF_1) fep->work_tx |= (1 << 0); -- cgit v1.2.3-58-ga151 From 7063c163cd4a20184b3bbada503dab8f254a8c56 Mon Sep 17 00:00:00 2001 From: Troy Kisky Date: Tue, 19 Sep 2017 17:33:08 -0700 Subject: net: fec: remove unused interrupt FEC_ENET_TS_TIMER FEC_ENET_TS_TIMER is not checked in the interrupt routine so there is no need to enable it. Signed-off-by: Troy Kisky Acked-by: Fugang Duan Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec.h | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/freescale/fec.h b/drivers/net/ethernet/freescale/fec.h index 38c7b21e5d63..ede1876a9a19 100644 --- a/drivers/net/ethernet/freescale/fec.h +++ b/drivers/net/ethernet/freescale/fec.h @@ -374,8 +374,8 @@ struct bufdesc_ex { #define FEC_ENET_TS_AVAIL ((uint)0x00010000) #define FEC_ENET_TS_TIMER ((uint)0x00008000) -#define FEC_DEFAULT_IMASK (FEC_ENET_TXF | FEC_ENET_RXF | FEC_ENET_MII | FEC_ENET_TS_TIMER) -#define FEC_NAPI_IMASK (FEC_ENET_MII | FEC_ENET_TS_TIMER) +#define FEC_DEFAULT_IMASK (FEC_ENET_TXF | FEC_ENET_RXF | FEC_ENET_MII) +#define FEC_NAPI_IMASK FEC_ENET_MII #define FEC_RX_DISABLED_IMASK (FEC_DEFAULT_IMASK & (~FEC_ENET_RXF)) /* ENET interrupt coalescing macro define */ -- cgit v1.2.3-58-ga151 From e24ee2780a1d6786b94139ebf95b44c9ae62bf13 Mon Sep 17 00:00:00 2001 From: Troy Kisky Date: Tue, 19 Sep 2017 17:33:09 -0700 Subject: net: fec: return IRQ_HANDLED if fec_ptp_check_pps_event handled it fec_ptp_check_pps_event will return 1 if FEC_T_TF_MASK caused an interrupt. Don't return IRQ_NONE in this case. Signed-off-by: Troy Kisky Acked-by: Fugang Duan Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c index 464055fb33d5..3dc2d771a222 100644 --- a/drivers/net/ethernet/freescale/fec_main.c +++ b/drivers/net/ethernet/freescale/fec_main.c @@ -1604,8 +1604,8 @@ fec_enet_interrupt(int irq, void *dev_id) } if (fep->ptp_clock) - fec_ptp_check_pps_event(fep); - + if (fec_ptp_check_pps_event(fep)) + ret = IRQ_HANDLED; return ret; } -- cgit v1.2.3-58-ga151 From 02388bf87f72e1d47174cd8f81c34443920eb5a0 Mon Sep 17 00:00:00 2001 From: Meng Xu Date: Tue, 19 Sep 2017 21:49:55 -0400 Subject: isdn/i4l: fetch the ppp_write buffer in one shot In isdn_ppp_write(), the header (i.e., protobuf) of the buffer is fetched twice from userspace. The first fetch is used to peek at the protocol of the message and reset the huptimer if necessary; while the second fetch copies in the whole buffer. However, given that buf resides in userspace memory, a user process can race to change its memory content across fetches. By doing so, we can either avoid resetting the huptimer for any type of packets (by first setting proto to PPP_LCP and later change to the actual type) or force resetting the huptimer for LCP packets. This patch changes this double-fetch behavior into two single fetches decided by condition (lp->isdn_device < 0 || lp->isdn_channel <0). A more detailed discussion can be found at https://marc.info/?l=linux-kernel&m=150586376926123&w=2 Signed-off-by: Meng Xu Signed-off-by: David S. Miller --- drivers/isdn/i4l/isdn_ppp.c | 37 +++++++++++++++++++++++++------------ 1 file changed, 25 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/isdn/i4l/isdn_ppp.c b/drivers/isdn/i4l/isdn_ppp.c index 6c44609fd83a..cd2b3c69771a 100644 --- a/drivers/isdn/i4l/isdn_ppp.c +++ b/drivers/isdn/i4l/isdn_ppp.c @@ -825,7 +825,6 @@ isdn_ppp_write(int min, struct file *file, const char __user *buf, int count) isdn_net_local *lp; struct ippp_struct *is; int proto; - unsigned char protobuf[4]; is = file->private_data; @@ -839,24 +838,28 @@ isdn_ppp_write(int min, struct file *file, const char __user *buf, int count) if (!lp) printk(KERN_DEBUG "isdn_ppp_write: lp == NULL\n"); else { - /* - * Don't reset huptimer for - * LCP packets. (Echo requests). - */ - if (copy_from_user(protobuf, buf, 4)) - return -EFAULT; - proto = PPP_PROTOCOL(protobuf); - if (proto != PPP_LCP) - lp->huptimer = 0; + if (lp->isdn_device < 0 || lp->isdn_channel < 0) { + unsigned char protobuf[4]; + /* + * Don't reset huptimer for + * LCP packets. (Echo requests). + */ + if (copy_from_user(protobuf, buf, 4)) + return -EFAULT; + + proto = PPP_PROTOCOL(protobuf); + if (proto != PPP_LCP) + lp->huptimer = 0; - if (lp->isdn_device < 0 || lp->isdn_channel < 0) return 0; + } if ((dev->drv[lp->isdn_device]->flags & DRV_FLAG_RUNNING) && lp->dialstate == 0 && (lp->flags & ISDN_NET_CONNECTED)) { unsigned short hl; struct sk_buff *skb; + unsigned char *cpy_buf; /* * we need to reserve enough space in front of * sk_buff. old call to dev_alloc_skb only reserved @@ -869,11 +872,21 @@ isdn_ppp_write(int min, struct file *file, const char __user *buf, int count) return count; } skb_reserve(skb, hl); - if (copy_from_user(skb_put(skb, count), buf, count)) + cpy_buf = skb_put(skb, count); + if (copy_from_user(cpy_buf, buf, count)) { kfree_skb(skb); return -EFAULT; } + + /* + * Don't reset huptimer for + * LCP packets. (Echo requests). + */ + proto = PPP_PROTOCOL(cpy_buf); + if (proto != PPP_LCP) + lp->huptimer = 0; + if (is->debug & 0x40) { printk(KERN_DEBUG "ppp xmit: len %d\n", (int) skb->len); isdn_ppp_frame_log("xmit", skb->data, skb->len, 32, is->unit, lp->ppp_slot); -- cgit v1.2.3-58-ga151 From e92a0843795779678397ac0790a76de20f79cc13 Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:50 +0800 Subject: net: hns3: Cleanup for ROCE capability flag in ae_dev This patch add the ROCE supported flag in the driver_data field of pci_device_id, delete roce_pci_tbl and change HNAE_DEV_SUPPORT_ROCE_B to HNAE3_DEV_SUPPORT_ROCE_B. This cleanup is done in order to support adding capability in pci_device_id and to fix initialization failure when cmd is not supported. Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hnae3.h | 5 ++++- .../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 25 ++++------------------ .../net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c | 16 +++++++++----- 3 files changed, 19 insertions(+), 27 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hnae3.h b/drivers/net/ethernet/hisilicon/hns3/hnae3.h index b2f28ae81273..0f7b61a92f44 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hnae3.h +++ b/drivers/net/ethernet/hisilicon/hns3/hnae3.h @@ -49,7 +49,10 @@ #define HNAE3_CLASS_NAME_SIZE 16 #define HNAE3_DEV_INITED_B 0x0 -#define HNAE_DEV_SUPPORT_ROCE_B 0x1 +#define HNAE3_DEV_SUPPORT_ROCE_B 0x1 + +#define hnae3_dev_roce_supported(hdev) \ + hnae_get_bit(hdev->ae_dev->flag, HNAE3_DEV_SUPPORT_ROCE_B) #define ring_ptr_move_fw(ring, p) \ ((ring)->p = ((ring)->p + 1) % (ring)->desc_num) diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 74008ef23169..6953d19c6475 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -46,17 +46,7 @@ static const struct pci_device_id ae_algo_pci_tbl[] = { {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA), 0}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA_MACSEC), 0}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_100G_RDMA_MACSEC), 0}, - /* Required last entry */ - {0, } -}; - -static const struct pci_device_id roce_pci_tbl[] = { - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE_RDMA), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE_RDMA_MACSEC), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA_MACSEC), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_100G_RDMA_MACSEC), 0}, - /* Required last entry */ + /* required last entry */ {0, } }; @@ -894,7 +884,7 @@ static int hclge_query_pf_resource(struct hclge_dev *hdev) hdev->num_tqps = __le16_to_cpu(req->tqp_num); hdev->pkt_buf_size = __le16_to_cpu(req->buf_size) << HCLGE_BUF_UNIT_S; - if (hnae_get_bit(hdev->ae_dev->flag, HNAE_DEV_SUPPORT_ROCE_B)) { + if (hnae3_dev_roce_supported(hdev)) { hdev->num_roce_msix = hnae_get_field(__le16_to_cpu(req->pf_intr_vector_number), HCLGE_PF_VEC_NUM_M, HCLGE_PF_VEC_NUM_S); @@ -3932,8 +3922,7 @@ static int hclge_init_client_instance(struct hnae3_client *client, goto err; if (hdev->roce_client && - hnae_get_bit(hdev->ae_dev->flag, - HNAE_DEV_SUPPORT_ROCE_B)) { + hnae3_dev_roce_supported(hdev)) { struct hnae3_client *rc = hdev->roce_client; ret = hclge_init_roce_base_info(vport); @@ -3956,8 +3945,7 @@ static int hclge_init_client_instance(struct hnae3_client *client, break; case HNAE3_CLIENT_ROCE: - if (hnae_get_bit(hdev->ae_dev->flag, - HNAE_DEV_SUPPORT_ROCE_B)) { + if (hnae3_dev_roce_supported(hdev)) { hdev->roce_client = client; vport->roce.client = client; } @@ -4069,7 +4057,6 @@ static void hclge_pci_uninit(struct hclge_dev *hdev) static int hclge_init_ae_dev(struct hnae3_ae_dev *ae_dev) { struct pci_dev *pdev = ae_dev->pdev; - const struct pci_device_id *id; struct hclge_dev *hdev; int ret; @@ -4084,10 +4071,6 @@ static int hclge_init_ae_dev(struct hnae3_ae_dev *ae_dev) hdev->ae_dev = ae_dev; ae_dev->priv = hdev; - id = pci_match_id(roce_pci_tbl, ae_dev->pdev); - if (id) - hnae_set_bit(ae_dev->flag, HNAE_DEV_SUPPORT_ROCE_B, 1); - ret = hclge_pci_init(hdev); if (ret) { dev_err(&pdev->dev, "PCI init failed\n"); diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c index 4d68d6ea5143..94d8bb5b92f0 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c @@ -41,11 +41,16 @@ static struct hnae3_client client; static const struct pci_device_id hns3_pci_tbl[] = { {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_GE), 0}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE_RDMA), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE_RDMA_MACSEC), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA_MACSEC), 0}, - {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_100G_RDMA_MACSEC), 0}, + {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE_RDMA), + BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE_RDMA_MACSEC), + BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA), + BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA_MACSEC), + BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_100G_RDMA_MACSEC), + BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, /* required last entry */ {0, } }; @@ -1348,6 +1353,7 @@ static int hns3_probe(struct pci_dev *pdev, const struct pci_device_id *ent) } ae_dev->pdev = pdev; + ae_dev->flag = ent->driver_data; ae_dev->dev_type = HNAE3_DEV_KNIC; pci_set_drvdata(pdev, ae_dev); -- cgit v1.2.3-58-ga151 From 2daf4a6536f3109ed0ed758cec14743e0e5c20ea Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:51 +0800 Subject: net: hns3: Fix initialization when cmd is not supported When ae_dev doesn't support DCB, rx_priv_wl_config, common_thrd_config and tm_qs_bp_cfg can't be called, otherwise cmd return fail, which causes the hclge module initialization process to fail. This patch fix it by adding a DCB capability flag to check if the ae_dev support DCB. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hnae3.h | 7 ++++++ .../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 26 +++++++++++++--------- .../net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c | 4 ++++ .../net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c | 10 ++++----- 4 files changed, 31 insertions(+), 16 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hnae3.h b/drivers/net/ethernet/hisilicon/hns3/hnae3.h index 0f7b61a92f44..ad685f5aa6d1 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hnae3.h +++ b/drivers/net/ethernet/hisilicon/hns3/hnae3.h @@ -50,10 +50,17 @@ #define HNAE3_DEV_INITED_B 0x0 #define HNAE3_DEV_SUPPORT_ROCE_B 0x1 +#define HNAE3_DEV_SUPPORT_DCB_B 0x2 + +#define HNAE3_DEV_SUPPORT_ROCE_DCB_BITS (BIT(HNAE3_DEV_SUPPORT_DCB_B) |\ + BIT(HNAE3_DEV_SUPPORT_ROCE_B)) #define hnae3_dev_roce_supported(hdev) \ hnae_get_bit(hdev->ae_dev->flag, HNAE3_DEV_SUPPORT_ROCE_B) +#define hnae3_dev_dcb_supported(hdev) \ + hnae_get_bit(hdev->ae_dev->flag, HNAE3_DEV_SUPPORT_DCB_B) + #define ring_ptr_move_fw(ring, p) \ ((ring)->p = ((ring)->p + 1) % (ring)->desc_num) #define ring_ptr_move_bw(ring, p) \ diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 6953d19c6475..903f43a8c2a1 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -1772,18 +1772,22 @@ int hclge_buffer_alloc(struct hclge_dev *hdev) return ret; } - ret = hclge_rx_priv_wl_config(hdev); - if (ret) { - dev_err(&hdev->pdev->dev, - "could not configure rx private waterline %d\n", ret); - return ret; - } + if (hnae3_dev_dcb_supported(hdev)) { + ret = hclge_rx_priv_wl_config(hdev); + if (ret) { + dev_err(&hdev->pdev->dev, + "could not configure rx private waterline %d\n", + ret); + return ret; + } - ret = hclge_common_thrd_config(hdev); - if (ret) { - dev_err(&hdev->pdev->dev, - "could not configure common threshold %d\n", ret); - return ret; + ret = hclge_common_thrd_config(hdev); + if (ret) { + dev_err(&hdev->pdev->dev, + "could not configure common threshold %d\n", + ret); + return ret; + } } ret = hclge_common_wl_config(hdev); diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c index 1c577d268f00..c91dbf19c4b1 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c @@ -976,6 +976,10 @@ int hclge_pause_setup_hw(struct hclge_dev *hdev) if (ret) return ret; + /* Only DCB-supported dev supports qset back pressure setting */ + if (!hnae3_dev_dcb_supported(hdev)) + return 0; + for (i = 0; i < hdev->tm_info.num_tc; i++) { ret = hclge_tm_qs_bp_cfg(hdev, i); if (ret) diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c index 94d8bb5b92f0..35369e1c8036 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hns3_enet.c @@ -42,15 +42,15 @@ static const struct pci_device_id hns3_pci_tbl[] = { {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_GE), 0}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE), 0}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE_RDMA), - BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + HNAE3_DEV_SUPPORT_ROCE_DCB_BITS}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_25GE_RDMA_MACSEC), - BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + HNAE3_DEV_SUPPORT_ROCE_DCB_BITS}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA), - BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + HNAE3_DEV_SUPPORT_ROCE_DCB_BITS}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_50GE_RDMA_MACSEC), - BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + HNAE3_DEV_SUPPORT_ROCE_DCB_BITS}, {PCI_VDEVICE(HUAWEI, HNAE3_DEV_ID_100G_RDMA_MACSEC), - BIT(HNAE3_DEV_SUPPORT_ROCE_B)}, + HNAE3_DEV_SUPPORT_ROCE_DCB_BITS}, /* required last entry */ {0, } }; -- cgit v1.2.3-58-ga151 From d221df4e0faae2b9cc8ad78f3e5e777461b6b542 Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:52 +0800 Subject: net: hns3: Fix for DEFAULT_DV when dev doesn't support DCB When ae_dev doesn't support DCB, DEFAULT_DV must be set to a lower value, otherwise the buffer allocation process will fail. This patch fix it by setting it to 30K bytes. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h | 1 + drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 6 +++++- 2 files changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h index c2b613b40509..30e2ad5ac0da 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h @@ -688,6 +688,7 @@ struct hclge_reset_tqp_queue { #define HCLGE_DEFAULT_TX_BUF 0x4000 /* 16k bytes */ #define HCLGE_TOTAL_PKT_BUF 0x108000 /* 1.03125M bytes */ #define HCLGE_DEFAULT_DV 0xA000 /* 40k byte */ +#define HCLGE_DEFAULT_NON_DCB_DV 0x7800 /* 30K byte */ #define HCLGE_TYPE_CRQ 0 #define HCLGE_TYPE_CSQ 1 diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 903f43a8c2a1..796370adf99c 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -1444,7 +1444,11 @@ static bool hclge_is_rx_buf_ok(struct hclge_dev *hdev, u32 rx_all) tc_num = hclge_get_tc_num(hdev); pfc_enable_num = hclge_get_pfc_enalbe_num(hdev); - shared_buf_min = 2 * hdev->mps + HCLGE_DEFAULT_DV; + if (hnae3_dev_dcb_supported(hdev)) + shared_buf_min = 2 * hdev->mps + HCLGE_DEFAULT_DV; + else + shared_buf_min = 2 * hdev->mps + HCLGE_DEFAULT_NON_DCB_DV; + shared_buf_tc = pfc_enable_num * hdev->mps + (tc_num - pfc_enable_num) * hdev->mps / 2 + hdev->mps; -- cgit v1.2.3-58-ga151 From bb1fe9ea6371e075d3d1448cd3ff6441d31307be Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:53 +0800 Subject: net: hns3: Fix for not setting rx private buffer size to zero When rx private buffer is disabled, there may be some case that the rx private buffer is not set to zero, which may cause buffer allocation process to fail. This patch fixes this problem by setting priv->enable to 0 and priv->buf_size to zero when rx private buffer is disabled. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index 796370adf99c..a7d8fb1e15f6 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -1504,6 +1504,11 @@ int hclge_rx_buffer_calc(struct hclge_dev *hdev, u32 tx_size) priv->wl.high = 2 * hdev->mps; priv->buf_size = priv->wl.high; } + } else { + priv->enable = 0; + priv->wl.low = 0; + priv->wl.high = 0; + priv->buf_size = 0; } } @@ -1516,8 +1521,15 @@ int hclge_rx_buffer_calc(struct hclge_dev *hdev, u32 tx_size) for (i = 0; i < HCLGE_MAX_TC_NUM; i++) { priv = &hdev->priv_buf[i]; - if (hdev->hw_tc_map & BIT(i)) - priv->enable = 1; + priv->enable = 0; + priv->wl.low = 0; + priv->wl.high = 0; + priv->buf_size = 0; + + if (!(hdev->hw_tc_map & BIT(i))) + continue; + + priv->enable = 1; if (hdev->tm_info.hw_pfc_map & BIT(i)) { priv->wl.low = 128; -- cgit v1.2.3-58-ga151 From b8c8bf47da5576657370798da6f18a8cb0245d5b Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:54 +0800 Subject: net: hns3: Fix for rx_priv_buf_alloc not setting rx shared buffer rx_priv_buf_alloc is used to tell hardware how much buffer is used for rx direction, right now only the private buffer is assigned. For ae_dev that doesn't support DCB, private rx buffer is assigned to zero, only shared rx buffer is used. So not setting the shared rx buffer cause dropping of packet in SSU. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h | 3 ++- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 4 ++++ 2 files changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h index 30e2ad5ac0da..758cf3948131 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_cmd.h @@ -270,7 +270,8 @@ struct hclge_tx_buff_alloc { struct hclge_rx_priv_buff { __le16 buf_num[HCLGE_TC_NUM]; - u8 rsv[8]; + __le16 shared_buf; + u8 rsv[6]; }; struct hclge_query_version { diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index a7d8fb1e15f6..e313552bb23d 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -1622,6 +1622,10 @@ static int hclge_rx_priv_buf_alloc(struct hclge_dev *hdev) cpu_to_le16(true << HCLGE_TC0_PRI_BUF_EN_B); } + req->shared_buf = + cpu_to_le16((hdev->s_buf.buf_size >> HCLGE_BUF_UNIT_S) | + (1 << HCLGE_TC0_PRI_BUF_EN_B)); + ret = hclge_cmd_send(&hdev->hw, &desc, 1); if (ret) { dev_err(&hdev->pdev->dev, -- cgit v1.2.3-58-ga151 From d602a52540c9b92e0dd152cfe1d0848c23f08894 Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:55 +0800 Subject: net: hns3: Fix for rx priv buf allocation when DCB is not supported When hdev doesn't support DCB, rx private buffer is not allocated, otherwise there is not enough buffer for rx shared buffer, causing buffer allocation process to fail. This patch fixes by checking the dcb capability in hclge_rx_buffer_calc. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 10 ++++++++++ 1 file changed, 10 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index e313552bb23d..c660f0caf709 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -1489,6 +1489,16 @@ int hclge_rx_buffer_calc(struct hclge_dev *hdev, u32 tx_size) struct hclge_priv_buf *priv; int i; + /* When DCB is not supported, rx private + * buffer is not allocated. + */ + if (!hnae3_dev_dcb_supported(hdev)) { + if (!hclge_is_rx_buf_ok(hdev, rx_all)) + return -ENOMEM; + + return 0; + } + /* step 1, try to alloc private buffer for all enabled tc */ for (i = 0; i < HCLGE_MAX_TC_NUM; i++) { priv = &hdev->priv_buf[i]; -- cgit v1.2.3-58-ga151 From c4726338d928c824f56c27734d837b8244132705 Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:56 +0800 Subject: net: hns3: Fix typo error for feild in hclge_tm This patch fixes a typo error for feild, which should be field. Fixes: 848440544b41f ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- .../net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c | 20 ++++++++++---------- .../net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.h | 4 ++-- 2 files changed, 12 insertions(+), 12 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c index c91dbf19c4b1..fe659f752237 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c @@ -280,11 +280,11 @@ static int hclge_tm_pg_shapping_cfg(struct hclge_dev *hdev, shap_cfg_cmd->pg_id = pg_id; - hclge_tm_set_feild(shap_cfg_cmd->pg_shapping_para, IR_B, ir_b); - hclge_tm_set_feild(shap_cfg_cmd->pg_shapping_para, IR_U, ir_u); - hclge_tm_set_feild(shap_cfg_cmd->pg_shapping_para, IR_S, ir_s); - hclge_tm_set_feild(shap_cfg_cmd->pg_shapping_para, BS_B, bs_b); - hclge_tm_set_feild(shap_cfg_cmd->pg_shapping_para, BS_S, bs_s); + hclge_tm_set_field(shap_cfg_cmd->pg_shapping_para, IR_B, ir_b); + hclge_tm_set_field(shap_cfg_cmd->pg_shapping_para, IR_U, ir_u); + hclge_tm_set_field(shap_cfg_cmd->pg_shapping_para, IR_S, ir_s); + hclge_tm_set_field(shap_cfg_cmd->pg_shapping_para, BS_B, bs_b); + hclge_tm_set_field(shap_cfg_cmd->pg_shapping_para, BS_S, bs_s); return hclge_cmd_send(&hdev->hw, &desc, 1); } @@ -307,11 +307,11 @@ static int hclge_tm_pri_shapping_cfg(struct hclge_dev *hdev, shap_cfg_cmd->pri_id = pri_id; - hclge_tm_set_feild(shap_cfg_cmd->pri_shapping_para, IR_B, ir_b); - hclge_tm_set_feild(shap_cfg_cmd->pri_shapping_para, IR_U, ir_u); - hclge_tm_set_feild(shap_cfg_cmd->pri_shapping_para, IR_S, ir_s); - hclge_tm_set_feild(shap_cfg_cmd->pri_shapping_para, BS_B, bs_b); - hclge_tm_set_feild(shap_cfg_cmd->pri_shapping_para, BS_S, bs_s); + hclge_tm_set_field(shap_cfg_cmd->pri_shapping_para, IR_B, ir_b); + hclge_tm_set_field(shap_cfg_cmd->pri_shapping_para, IR_U, ir_u); + hclge_tm_set_field(shap_cfg_cmd->pri_shapping_para, IR_S, ir_s); + hclge_tm_set_field(shap_cfg_cmd->pri_shapping_para, BS_B, bs_b); + hclge_tm_set_field(shap_cfg_cmd->pri_shapping_para, BS_S, bs_s); return hclge_cmd_send(&hdev->hw, &desc, 1); } diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.h index 7e67337dfaf2..85158b0d73fe 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.h +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.h @@ -94,10 +94,10 @@ struct hclge_bp_to_qs_map_cmd { u32 rsvd1; }; -#define hclge_tm_set_feild(dest, string, val) \ +#define hclge_tm_set_field(dest, string, val) \ hnae_set_field((dest), (HCLGE_TM_SHAP_##string##_MSK), \ (HCLGE_TM_SHAP_##string##_LSH), val) -#define hclge_tm_get_feild(src, string) \ +#define hclge_tm_get_field(src, string) \ hnae_get_field((src), (HCLGE_TM_SHAP_##string##_MSK), \ (HCLGE_TM_SHAP_##string##_LSH)) -- cgit v1.2.3-58-ga151 From 68ece54efd417d415462adbaa2700cba50de3ff6 Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:57 +0800 Subject: net: hns3: Fix for setting rss_size incorrectly rss_size is 1, 2, 4, 8, 16, 32, 64, 128, but acutal tc queue size can be any u16 less than 128. If tc queue size is 5, we set the rss_size to 8, indirection table will be used to limit the size of actual queue size. It may cause dropping of receiving packet in hardware if rss_size is not set correctly. For now, each TC has the same rss size. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- .../ethernet/hisilicon/hns3/hns3pf/hclge_main.c | 76 ++++++++++------------ .../ethernet/hisilicon/hns3/hns3pf/hclge_main.h | 1 + .../net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c | 1 + 3 files changed, 38 insertions(+), 40 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c index c660f0caf709..e0685e630afe 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c @@ -2606,6 +2606,7 @@ static int hclge_rss_init_hw(struct hclge_dev *hdev) u16 tc_valid[HCLGE_MAX_TC_NUM]; u16 tc_size[HCLGE_MAX_TC_NUM]; u32 *rss_indir = NULL; + u16 rss_size = 0, roundup_size; const u8 *key; int i, ret, j; @@ -2620,7 +2621,13 @@ static int hclge_rss_init_hw(struct hclge_dev *hdev) for (j = 0; j < hdev->num_vmdq_vport + 1; j++) { for (i = 0; i < HCLGE_RSS_IND_TBL_SIZE; i++) { vport[j].rss_indirection_tbl[i] = - i % hdev->rss_size_max; + i % vport[j].alloc_rss_size; + + /* vport 0 is for PF */ + if (j != 0) + continue; + + rss_size = vport[j].alloc_rss_size; rss_indir[i] = vport[j].rss_indirection_tbl[i]; } } @@ -2637,42 +2644,31 @@ static int hclge_rss_init_hw(struct hclge_dev *hdev) if (ret) goto err; + /* Each TC have the same queue size, and tc_size set to hardware is + * the log2 of roundup power of two of rss_size, the acutal queue + * size is limited by indirection table. + */ + if (rss_size > HCLGE_RSS_TC_SIZE_7 || rss_size == 0) { + dev_err(&hdev->pdev->dev, + "Configure rss tc size failed, invalid TC_SIZE = %d\n", + rss_size); + return -EINVAL; + } + + roundup_size = roundup_pow_of_two(rss_size); + roundup_size = ilog2(roundup_size); + for (i = 0; i < HCLGE_MAX_TC_NUM; i++) { - if (hdev->hw_tc_map & BIT(i)) - tc_valid[i] = 1; - else - tc_valid[i] = 0; + tc_valid[i] = 0; - switch (hdev->rss_size_max) { - case HCLGE_RSS_TC_SIZE_0: - tc_size[i] = 0; - break; - case HCLGE_RSS_TC_SIZE_1: - tc_size[i] = 1; - break; - case HCLGE_RSS_TC_SIZE_2: - tc_size[i] = 2; - break; - case HCLGE_RSS_TC_SIZE_3: - tc_size[i] = 3; - break; - case HCLGE_RSS_TC_SIZE_4: - tc_size[i] = 4; - break; - case HCLGE_RSS_TC_SIZE_5: - tc_size[i] = 5; - break; - case HCLGE_RSS_TC_SIZE_6: - tc_size[i] = 6; - break; - case HCLGE_RSS_TC_SIZE_7: - tc_size[i] = 7; - break; - default: - break; - } - tc_offset[i] = hdev->rss_size_max * i; + if (!(hdev->hw_tc_map & BIT(i))) + continue; + + tc_valid[i] = 1; + tc_size[i] = roundup_size; + tc_offset[i] = rss_size * i; } + ret = hclge_set_rss_tc_mode(hdev, tc_valid, tc_size, tc_offset); err: @@ -4167,12 +4163,6 @@ static int hclge_init_ae_dev(struct hnae3_ae_dev *ae_dev) return ret; } - ret = hclge_rss_init_hw(hdev); - if (ret) { - dev_err(&pdev->dev, "Rss init fail, ret =%d\n", ret); - return ret; - } - ret = hclge_init_vlan_config(hdev); if (ret) { dev_err(&pdev->dev, "VLAN init fail, ret =%d\n", ret); @@ -4185,6 +4175,12 @@ static int hclge_init_ae_dev(struct hnae3_ae_dev *ae_dev) return ret; } + ret = hclge_rss_init_hw(hdev); + if (ret) { + dev_err(&pdev->dev, "Rss init fail, ret =%d\n", ret); + return ret; + } + setup_timer(&hdev->service_timer, hclge_service_timer, (unsigned long)hdev); INIT_WORK(&hdev->service_task, hclge_service_task); diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h index edb10ad075eb..7f8dd129c10d 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h @@ -477,6 +477,7 @@ struct hclge_vport { u8 rss_hash_key[HCLGE_RSS_KEY_SIZE]; /* User configured hash keys */ /* User configured lookup table entries */ u8 rss_indirection_tbl[HCLGE_RSS_IND_TBL_SIZE]; + u16 alloc_rss_size; u16 qs_offset; u16 bw_limit; /* VSI BW Limit (0 = disabled) */ diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c index fe659f752237..b7ba7aa66620 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c @@ -397,6 +397,7 @@ static void hclge_tm_vport_tc_info_update(struct hclge_vport *vport) kinfo->num_tqps / kinfo->num_tc); vport->qs_offset = hdev->tm_info.num_tc * vport->vport_id; vport->dwrr = 100; /* 100 percent as init */ + vport->alloc_rss_size = kinfo->rss_size; for (i = 0; i < kinfo->num_tc; i++) { if (hdev->hw_tc_map & BIT(i)) { -- cgit v1.2.3-58-ga151 From c5795c5308af81568d1573598716091120c85a38 Mon Sep 17 00:00:00 2001 From: Yunsheng Lin Date: Wed, 20 Sep 2017 18:52:58 +0800 Subject: net: hns3: Fix for pri to tc mapping in TM Current mapping between pri and tc is one to one, so user can't map multi priorities to the same tc. This patch changes the mapping to many to one. Fixes: 848440544b41f ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver") Signed-off-by: Yunsheng Lin Signed-off-by: David S. Miller --- drivers/net/ethernet/hisilicon/hns3/hnae3.h | 3 ++- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h | 2 +- drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c | 16 +++++++++------- 3 files changed, 12 insertions(+), 9 deletions(-) (limited to 'drivers') diff --git a/drivers/net/ethernet/hisilicon/hns3/hnae3.h b/drivers/net/ethernet/hisilicon/hns3/hnae3.h index ad685f5aa6d1..1a01cadfe5f3 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hnae3.h +++ b/drivers/net/ethernet/hisilicon/hns3/hnae3.h @@ -376,12 +376,12 @@ struct hnae3_ae_algo { struct hnae3_tc_info { u16 tqp_offset; /* TQP offset from base TQP */ u16 tqp_count; /* Total TQPs */ - u8 up; /* user priority */ u8 tc; /* TC index */ bool enable; /* If this TC is enable or not */ }; #define HNAE3_MAX_TC 8 +#define HNAE3_MAX_USER_PRIO 8 struct hnae3_knic_private_info { struct net_device *netdev; /* Set by KNIC client when init instance */ u16 rss_size; /* Allocated RSS queues */ @@ -389,6 +389,7 @@ struct hnae3_knic_private_info { u16 num_desc; u8 num_tc; /* Total number of enabled TCs */ + u8 prio_tc[HNAE3_MAX_USER_PRIO]; /* TC indexed by prio */ struct hnae3_tc_info tc_info[HNAE3_MAX_TC]; /* Idx of array is HW TC */ u16 num_tqps; /* total number of TQPs in this handle */ diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h index 7f8dd129c10d..9fcfd9395424 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.h @@ -176,7 +176,6 @@ struct hclge_pg_info { struct hclge_tc_info { u8 tc_id; u8 tc_sch_mode; /* 0: sp; 1: dwrr */ - u8 up; u8 pgid; u32 bw_limit; }; @@ -197,6 +196,7 @@ struct hclge_tm_info { u8 num_tc; u8 num_pg; /* It must be 1 if vNET-Base schd */ u8 pg_dwrr[HCLGE_PG_NUM]; + u8 prio_tc[HNAE3_MAX_USER_PRIO]; struct hclge_pg_info pg_info[HCLGE_PG_NUM]; struct hclge_tc_info tc_info[HNAE3_MAX_TC]; enum hclge_fc_mode fc_mode; diff --git a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c index b7ba7aa66620..73a75d7cc551 100644 --- a/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c +++ b/drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_tm.c @@ -128,9 +128,7 @@ static int hclge_fill_pri_array(struct hclge_dev *hdev, u8 *pri, u8 pri_id) { u8 tc; - for (tc = 0; tc < hdev->tm_info.num_tc; tc++) - if (hdev->tm_info.tc_info[tc].up == pri_id) - break; + tc = hdev->tm_info.prio_tc[pri_id]; if (tc >= hdev->tm_info.num_tc) return -EINVAL; @@ -158,7 +156,7 @@ static int hclge_up_to_tc_map(struct hclge_dev *hdev) hclge_cmd_setup_basic_desc(&desc, HCLGE_OPC_PRI_TO_TC_MAPPING, false); - for (pri_id = 0; pri_id < hdev->tm_info.num_tc; pri_id++) { + for (pri_id = 0; pri_id < HNAE3_MAX_USER_PRIO; pri_id++) { ret = hclge_fill_pri_array(hdev, pri, pri_id); if (ret) return ret; @@ -405,16 +403,17 @@ static void hclge_tm_vport_tc_info_update(struct hclge_vport *vport) kinfo->tc_info[i].tqp_offset = i * kinfo->rss_size; kinfo->tc_info[i].tqp_count = kinfo->rss_size; kinfo->tc_info[i].tc = i; - kinfo->tc_info[i].up = hdev->tm_info.tc_info[i].up; } else { /* Set to default queue if TC is disable */ kinfo->tc_info[i].enable = false; kinfo->tc_info[i].tqp_offset = 0; kinfo->tc_info[i].tqp_count = 1; kinfo->tc_info[i].tc = 0; - kinfo->tc_info[i].up = 0; } } + + memcpy(kinfo->prio_tc, hdev->tm_info.prio_tc, + FIELD_SIZEOF(struct hnae3_knic_private_info, prio_tc)); } static void hclge_tm_vport_info_update(struct hclge_dev *hdev) @@ -436,12 +435,15 @@ static void hclge_tm_tc_info_init(struct hclge_dev *hdev) for (i = 0; i < hdev->tm_info.num_tc; i++) { hdev->tm_info.tc_info[i].tc_id = i; hdev->tm_info.tc_info[i].tc_sch_mode = HCLGE_SCH_MODE_DWRR; - hdev->tm_info.tc_info[i].up = i; hdev->tm_info.tc_info[i].pgid = 0; hdev->tm_info.tc_info[i].bw_limit = hdev->tm_info.pg_info[0].bw_limit; } + for (i = 0; i < HNAE3_MAX_USER_PRIO; i++) + hdev->tm_info.prio_tc[i] = + (i >= hdev->tm_info.num_tc) ? 0 : i; + hdev->flag &= ~HCLGE_FLAG_DCB_ENABLE; } -- cgit v1.2.3-58-ga151 From 0ab09befdbb7ca9b969d6206108629ddff43876e Mon Sep 17 00:00:00 2001 From: Alex Ng Date: Wed, 20 Sep 2017 11:17:35 -0700 Subject: hv_netvsc: fix send buffer failure on MTU change MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit If MTU is changed the host would reject the send buffer change. This problem is result of recent change to allow changing send buffer size. Every time we change the MTU, we store the previous net_device section count before destroying the buffer, but we don’t store the previous section size. When we reinitialize the buffer, its size is calculated by multiplying the previous count and previous size. Since we continuously increase the MTU, the host returns us a decreasing count value while the section size is reinitialized to 1728 bytes every time. This eventually leads to a condition where the calculated buf_size is so small that the host rejects it. Fixes: 8b5327975ae1 ("netvsc: allow controlling send/recv buffer size") Signed-off-by: Alex Ng Signed-off-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/hyperv/hyperv_net.h | 2 ++ drivers/net/hyperv/netvsc.c | 7 ++----- drivers/net/hyperv/netvsc_drv.c | 8 ++++++++ 3 files changed, 12 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/hyperv/hyperv_net.h b/drivers/net/hyperv/hyperv_net.h index d98cdfb1536b..5176be76ca7d 100644 --- a/drivers/net/hyperv/hyperv_net.h +++ b/drivers/net/hyperv/hyperv_net.h @@ -150,6 +150,8 @@ struct netvsc_device_info { u32 num_chn; u32 send_sections; u32 recv_sections; + u32 send_section_size; + u32 recv_section_size; }; enum rndis_device_state { diff --git a/drivers/net/hyperv/netvsc.c b/drivers/net/hyperv/netvsc.c index a5511b7326af..8d5077fb0492 100644 --- a/drivers/net/hyperv/netvsc.c +++ b/drivers/net/hyperv/netvsc.c @@ -76,9 +76,6 @@ static struct netvsc_device *alloc_net_device(void) net_device->max_pkt = RNDIS_MAX_PKT_DEFAULT; net_device->pkt_align = RNDIS_PKT_ALIGN_DEFAULT; - net_device->recv_section_size = NETVSC_RECV_SECTION_SIZE; - net_device->send_section_size = NETVSC_SEND_SECTION_SIZE; - init_completion(&net_device->channel_init_wait); init_waitqueue_head(&net_device->subchan_open); INIT_WORK(&net_device->subchan_work, rndis_set_subchannel); @@ -262,7 +259,7 @@ static int netvsc_init_buf(struct hv_device *device, int ret = 0; /* Get receive buffer area. */ - buf_size = device_info->recv_sections * net_device->recv_section_size; + buf_size = device_info->recv_sections * device_info->recv_section_size; buf_size = roundup(buf_size, PAGE_SIZE); net_device->recv_buf = vzalloc(buf_size); @@ -344,7 +341,7 @@ static int netvsc_init_buf(struct hv_device *device, goto cleanup; /* Now setup the send buffer. */ - buf_size = device_info->send_sections * net_device->send_section_size; + buf_size = device_info->send_sections * device_info->send_section_size; buf_size = round_up(buf_size, PAGE_SIZE); net_device->send_buf = vzalloc(buf_size); diff --git a/drivers/net/hyperv/netvsc_drv.c b/drivers/net/hyperv/netvsc_drv.c index d4902ee5f260..a32ae02e1b6c 100644 --- a/drivers/net/hyperv/netvsc_drv.c +++ b/drivers/net/hyperv/netvsc_drv.c @@ -848,7 +848,9 @@ static int netvsc_set_channels(struct net_device *net, device_info.num_chn = count; device_info.ring_size = ring_size; device_info.send_sections = nvdev->send_section_cnt; + device_info.send_section_size = nvdev->send_section_size; device_info.recv_sections = nvdev->recv_section_cnt; + device_info.recv_section_size = nvdev->recv_section_size; rndis_filter_device_remove(dev, nvdev); @@ -963,7 +965,9 @@ static int netvsc_change_mtu(struct net_device *ndev, int mtu) device_info.ring_size = ring_size; device_info.num_chn = nvdev->num_chn; device_info.send_sections = nvdev->send_section_cnt; + device_info.send_section_size = nvdev->send_section_size; device_info.recv_sections = nvdev->recv_section_cnt; + device_info.recv_section_size = nvdev->recv_section_size; rndis_filter_device_remove(hdev, nvdev); @@ -1485,7 +1489,9 @@ static int netvsc_set_ringparam(struct net_device *ndev, device_info.num_chn = nvdev->num_chn; device_info.ring_size = ring_size; device_info.send_sections = new_tx; + device_info.send_section_size = nvdev->send_section_size; device_info.recv_sections = new_rx; + device_info.recv_section_size = nvdev->recv_section_size; netif_device_detach(ndev); was_opened = rndis_filter_opened(nvdev); @@ -1934,7 +1940,9 @@ static int netvsc_probe(struct hv_device *dev, device_info.ring_size = ring_size; device_info.num_chn = VRSS_CHANNEL_DEFAULT; device_info.send_sections = NETVSC_DEFAULT_TX; + device_info.send_section_size = NETVSC_SEND_SECTION_SIZE; device_info.recv_sections = NETVSC_DEFAULT_RX; + device_info.recv_section_size = NETVSC_RECV_SECTION_SIZE; nvdev = rndis_filter_device_add(dev, &device_info); if (IS_ERR(nvdev)) { -- cgit v1.2.3-58-ga151 From 4a7a3860caac1a8779e8c459d8abe21b111798d6 Mon Sep 17 00:00:00 2001 From: Timur Tabi Date: Wed, 20 Sep 2017 15:32:53 -0500 Subject: net: qcom/emac: add software control for pause frame mode The EMAC has the option of sending only a single pause frame when flow control is enabled and the RX queue is full. Although sending only one pause frame has little value, this would allow admins to enable automatic flow control without having to worry about the EMAC flooding nearby switches with pause frames if the kernel hangs. The option is enabled by using the single-pause-mode private flag. Signed-off-by: Timur Tabi Signed-off-by: David S. Miller --- drivers/net/ethernet/qualcomm/emac/emac-ethtool.c | 30 +++++++++++++++++++++++ drivers/net/ethernet/qualcomm/emac/emac-mac.c | 22 +++++++++++++++++ drivers/net/ethernet/qualcomm/emac/emac.c | 3 +++ drivers/net/ethernet/qualcomm/emac/emac.h | 3 +++ 4 files changed, 58 insertions(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/qualcomm/emac/emac-ethtool.c b/drivers/net/ethernet/qualcomm/emac/emac-ethtool.c index bbe24639aa5a..c8c6231b87f3 100644 --- a/drivers/net/ethernet/qualcomm/emac/emac-ethtool.c +++ b/drivers/net/ethernet/qualcomm/emac/emac-ethtool.c @@ -88,6 +88,8 @@ static void emac_set_msglevel(struct net_device *netdev, u32 data) static int emac_get_sset_count(struct net_device *netdev, int sset) { switch (sset) { + case ETH_SS_PRIV_FLAGS: + return 1; case ETH_SS_STATS: return EMAC_STATS_LEN; default: @@ -100,6 +102,10 @@ static void emac_get_strings(struct net_device *netdev, u32 stringset, u8 *data) unsigned int i; switch (stringset) { + case ETH_SS_PRIV_FLAGS: + strcpy(data, "single-pause-mode"); + break; + case ETH_SS_STATS: for (i = 0; i < EMAC_STATS_LEN; i++) { strlcpy(data, emac_ethtool_stat_strings[i], @@ -230,6 +236,27 @@ static int emac_get_regs_len(struct net_device *netdev) return EMAC_MAX_REG_SIZE * sizeof(u32); } +#define EMAC_PRIV_ENABLE_SINGLE_PAUSE BIT(0) + +static int emac_set_priv_flags(struct net_device *netdev, u32 flags) +{ + struct emac_adapter *adpt = netdev_priv(netdev); + + adpt->single_pause_mode = !!(flags & EMAC_PRIV_ENABLE_SINGLE_PAUSE); + + if (netif_running(netdev)) + return emac_reinit_locked(adpt); + + return 0; +} + +static u32 emac_get_priv_flags(struct net_device *netdev) +{ + struct emac_adapter *adpt = netdev_priv(netdev); + + return adpt->single_pause_mode ? EMAC_PRIV_ENABLE_SINGLE_PAUSE : 0; +} + static const struct ethtool_ops emac_ethtool_ops = { .get_link_ksettings = phy_ethtool_get_link_ksettings, .set_link_ksettings = phy_ethtool_set_link_ksettings, @@ -253,6 +280,9 @@ static const struct ethtool_ops emac_ethtool_ops = { .get_regs_len = emac_get_regs_len, .get_regs = emac_get_regs, + + .set_priv_flags = emac_set_priv_flags, + .get_priv_flags = emac_get_priv_flags, }; void emac_set_ethtool_ops(struct net_device *netdev) diff --git a/drivers/net/ethernet/qualcomm/emac/emac-mac.c b/drivers/net/ethernet/qualcomm/emac/emac-mac.c index bcd4708b3745..0ea3ca09c689 100644 --- a/drivers/net/ethernet/qualcomm/emac/emac-mac.c +++ b/drivers/net/ethernet/qualcomm/emac/emac-mac.c @@ -551,6 +551,28 @@ static void emac_mac_start(struct emac_adapter *adpt) mac &= ~(HUGEN | VLAN_STRIP | TPAUSE | SIMR | HUGE | MULTI_ALL | DEBUG_MODE | SINGLE_PAUSE_MODE); + /* Enable single-pause-frame mode if requested. + * + * If enabled, the EMAC will send a single pause frame when the RX + * queue is full. This normally leads to packet loss because + * the pause frame disables the remote MAC only for 33ms (the quanta), + * and then the remote MAC continues sending packets even though + * the RX queue is still full. + * + * If disabled, the EMAC sends a pause frame every 31ms until the RX + * queue is no longer full. Normally, this is the preferred + * method of operation. However, when the system is hung (e.g. + * cores are halted), the EMAC interrupt handler is never called + * and so the RX queue fills up quickly and stays full. The resuling + * non-stop "flood" of pause frames sometimes has the effect of + * disabling nearby switches. In some cases, other nearby switches + * are also affected, shutting down the entire network. + * + * The user can enable or disable single-pause-frame mode + * via ethtool. + */ + mac |= adpt->single_pause_mode ? SINGLE_PAUSE_MODE : 0; + writel_relaxed(csr1, adpt->csr + EMAC_EMAC_WRAPPER_CSR1); writel_relaxed(mac, adpt->base + EMAC_MAC_CTRL); diff --git a/drivers/net/ethernet/qualcomm/emac/emac.c b/drivers/net/ethernet/qualcomm/emac/emac.c index 60850bfa3d32..759543512117 100644 --- a/drivers/net/ethernet/qualcomm/emac/emac.c +++ b/drivers/net/ethernet/qualcomm/emac/emac.c @@ -443,6 +443,9 @@ static void emac_init_adapter(struct emac_adapter *adpt) /* default to automatic flow control */ adpt->automatic = true; + + /* Disable single-pause-frame mode by default */ + adpt->single_pause_mode = false; } /* Get the clock */ diff --git a/drivers/net/ethernet/qualcomm/emac/emac.h b/drivers/net/ethernet/qualcomm/emac/emac.h index 8ee4ec6aef2e..d7c9f44209d4 100644 --- a/drivers/net/ethernet/qualcomm/emac/emac.h +++ b/drivers/net/ethernet/qualcomm/emac/emac.h @@ -363,6 +363,9 @@ struct emac_adapter { bool tx_flow_control; bool rx_flow_control; + /* True == use single-pause-frame mode. */ + bool single_pause_mode; + /* Ring parameter */ u8 tpd_burst; u8 rfd_burst; -- cgit v1.2.3-58-ga151 From ceb628134a75564d7bfa8e4ef902e6e588339e11 Mon Sep 17 00:00:00 2001 From: Florian Fainelli Date: Wed, 20 Sep 2017 15:52:14 -0700 Subject: net: phy: Keep reporting transceiver type With commit 2d55173e71b0 ("phy: add generic function to support ksetting support"), we lost the ability to report the transceiver type like we used to. Now that we have added back the transceiver type to ethtool_link_settings, we can report it back like we used to and have no loss of information. Fixes: 3f1ac7a700d0 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API") Fixes: 2d55173e71b0 ("phy: add generic function to support ksetting support") Signed-off-by: Florian Fainelli Signed-off-by: David S. Miller --- drivers/net/phy/phy.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/phy/phy.c b/drivers/net/phy/phy.c index e842d2cd1ee7..2b1e67bc1e73 100644 --- a/drivers/net/phy/phy.c +++ b/drivers/net/phy/phy.c @@ -373,7 +373,8 @@ void phy_ethtool_ksettings_get(struct phy_device *phydev, cmd->base.port = PORT_BNC; else cmd->base.port = PORT_MII; - + cmd->base.transceiver = phy_is_internal(phydev) ? + XCVR_INTERNAL : XCVR_EXTERNAL; cmd->base.phy_address = phydev->mdio.addr; cmd->base.autoneg = phydev->autoneg; cmd->base.eth_tp_mdix_ctrl = phydev->mdix_ctrl; -- cgit v1.2.3-58-ga151 From 8a7ffeb795f864dd605b579c05934cba95dc8ad3 Mon Sep 17 00:00:00 2001 From: Nisar Sayed Date: Thu, 21 Sep 2017 02:36:36 +0530 Subject: lan78xx: Fix for eeprom read/write when device auto suspend Fix for eeprom read/write when device auto suspend Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Nisar Sayed Signed-off-by: David S. Miller --- drivers/net/usb/lan78xx.c | 24 ++++++++++++++++++++---- 1 file changed, 20 insertions(+), 4 deletions(-) (limited to 'drivers') diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c index b99a7fb09f8e..fcf85ae37435 100644 --- a/drivers/net/usb/lan78xx.c +++ b/drivers/net/usb/lan78xx.c @@ -1265,30 +1265,46 @@ static int lan78xx_ethtool_get_eeprom(struct net_device *netdev, struct ethtool_eeprom *ee, u8 *data) { struct lan78xx_net *dev = netdev_priv(netdev); + int ret; + + ret = usb_autopm_get_interface(dev->intf); + if (ret) + return ret; ee->magic = LAN78XX_EEPROM_MAGIC; - return lan78xx_read_raw_eeprom(dev, ee->offset, ee->len, data); + ret = lan78xx_read_raw_eeprom(dev, ee->offset, ee->len, data); + + usb_autopm_put_interface(dev->intf); + + return ret; } static int lan78xx_ethtool_set_eeprom(struct net_device *netdev, struct ethtool_eeprom *ee, u8 *data) { struct lan78xx_net *dev = netdev_priv(netdev); + int ret; + + ret = usb_autopm_get_interface(dev->intf); + if (ret) + return ret; /* Allow entire eeprom update only */ if ((ee->magic == LAN78XX_EEPROM_MAGIC) && (ee->offset == 0) && (ee->len == 512) && (data[0] == EEPROM_INDICATOR)) - return lan78xx_write_raw_eeprom(dev, ee->offset, ee->len, data); + ret = lan78xx_write_raw_eeprom(dev, ee->offset, ee->len, data); else if ((ee->magic == LAN78XX_OTP_MAGIC) && (ee->offset == 0) && (ee->len == 512) && (data[0] == OTP_INDICATOR_1)) - return lan78xx_write_raw_otp(dev, ee->offset, ee->len, data); + ret = lan78xx_write_raw_otp(dev, ee->offset, ee->len, data); - return -EINVAL; + usb_autopm_put_interface(dev->intf); + + return ret; } static void lan78xx_get_strings(struct net_device *netdev, u32 stringset, -- cgit v1.2.3-58-ga151 From c077682282dd34c75e8477c22dffe7c9aebc6e98 Mon Sep 17 00:00:00 2001 From: Nisar Sayed Date: Thu, 21 Sep 2017 02:36:37 +0530 Subject: lan78xx: Allow EEPROM write for less than MAX_EEPROM_SIZE Allow EEPROM write for less than MAX_EEPROM_SIZE Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Nisar Sayed Signed-off-by: David S. Miller --- drivers/net/usb/lan78xx.c | 9 ++++----- 1 file changed, 4 insertions(+), 5 deletions(-) (limited to 'drivers') diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c index fcf85ae37435..f8c63eec8353 100644 --- a/drivers/net/usb/lan78xx.c +++ b/drivers/net/usb/lan78xx.c @@ -1290,11 +1290,10 @@ static int lan78xx_ethtool_set_eeprom(struct net_device *netdev, if (ret) return ret; - /* Allow entire eeprom update only */ - if ((ee->magic == LAN78XX_EEPROM_MAGIC) && - (ee->offset == 0) && - (ee->len == 512) && - (data[0] == EEPROM_INDICATOR)) + /* Invalid EEPROM_INDICATOR at offset zero will result in a failure + * to load data from EEPROM + */ + if (ee->magic == LAN78XX_EEPROM_MAGIC) ret = lan78xx_write_raw_eeprom(dev, ee->offset, ee->len, data); else if ((ee->magic == LAN78XX_OTP_MAGIC) && (ee->offset == 0) && -- cgit v1.2.3-58-ga151 From e365280521029c9366bab038915274ddaa1b7195 Mon Sep 17 00:00:00 2001 From: Nisar Sayed Date: Thu, 21 Sep 2017 02:36:38 +0530 Subject: lan78xx: Use default values loaded from EEPROM/OTP after reset Use default value of auto duplex and auto speed values loaded from EEPROM/OTP after reset. The LAN78xx allows platform configurations to be loaded from EEPROM/OTP. Ex: When external phy is connected, the MAC can be configured to have correct auto speed, auto duplex, auto polarity configured from the EEPROM/OTP. Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver") Signed-off-by: Nisar Sayed Signed-off-by: David S. Miller --- drivers/net/usb/lan78xx.c | 1 - 1 file changed, 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/usb/lan78xx.c b/drivers/net/usb/lan78xx.c index f8c63eec8353..0161f77641fa 100644 --- a/drivers/net/usb/lan78xx.c +++ b/drivers/net/usb/lan78xx.c @@ -2449,7 +2449,6 @@ static int lan78xx_reset(struct lan78xx_net *dev) /* LAN7801 only has RGMII mode */ if (dev->chipid == ID_REV_CHIP_ID_7801_) buf &= ~MAC_CR_GMII_EN_; - buf |= MAC_CR_AUTO_DUPLEX_ | MAC_CR_AUTO_SPEED_; ret = lan78xx_write_reg(dev, MAC_CR, buf); ret = lan78xx_read_reg(dev, MAC_TX, &buf); -- cgit v1.2.3-58-ga151 From f0ef1f4f2b772c0a1c8b35a6ae3edf974cc110dd Mon Sep 17 00:00:00 2001 From: Thomas Meyer Date: Thu, 21 Sep 2017 08:24:27 +0200 Subject: net: stmmac: Cocci spatch "of_table" Make sure (of/i2c/platform)_device_id tables are NULL terminated. Found by coccinelle spatch "misc/of_table.cocci" Signed-off-by: Thomas Meyer Signed-off-by: David S. Miller --- drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers') diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c index a366b3747eeb..8a280b48e3a9 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c @@ -315,6 +315,7 @@ static int stmmac_dt_phy(struct plat_stmmacenet_data *plat, { .compatible = "allwinner,sun8i-h3-emac" }, { .compatible = "allwinner,sun8i-v3s-emac" }, { .compatible = "allwinner,sun50i-a64-emac" }, + {}, }; /* If phy-handle property is passed from DT, use it as the PHY */ -- cgit v1.2.3-58-ga151 From 059fbe8b5171960bd5c2371bb327ac18733773de Mon Sep 17 00:00:00 2001 From: Geert Uytterhoeven Date: Thu, 21 Sep 2017 13:27:02 +0200 Subject: net: phy: Fix truncation of large IRQ numbers in phy_attached_print() Given NR_IRQS is 2048 on sparc64, and even 32784 on alpha, 3 digits is not enough to represent interrupt numbers on all architectures. Hence PHY interrupt numbers may be truncated during printing. Increase the buffer size from 4 to 8 bytes to fix this. Fixes: 5e369aefdce4818c ("net: stmmac: Delete dead code for MDIO registration") Signed-off-by: Geert Uytterhoeven Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- drivers/net/phy/phy_device.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers') diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c index 8cf0c5901f95..67f25ac29025 100644 --- a/drivers/net/phy/phy_device.c +++ b/drivers/net/phy/phy_device.c @@ -879,7 +879,7 @@ void phy_attached_print(struct phy_device *phydev, const char *fmt, ...) { const char *drv_name = phydev->drv ? phydev->drv->name : "unbound"; char *irq_str; - char irq_num[4]; + char irq_num[8]; switch(phydev->irq) { case PHY_POLL: -- cgit v1.2.3-58-ga151