From 7f42ace3118afedbd1848a349d01a11d9ca13d41 Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Thu, 14 Mar 2013 12:48:40 +0100 Subject: iwl3945: fix length of dma buffers commit bdb084b22d8aee66c87af5e9c36bd6cf7f3bccfd Author: Stanislaw Gruszka Date: Wed Feb 13 15:49:08 2013 +0100 iwlegacy: more checks for dma mapping errors broke il3945_tx_skb() dma buffer length settings, what results on firmware errors like showed below and make 3945 device non usable. iwl3945 0000:02:00.0: Microcode SW error detected. Restarting 0x82000008. iwl3945 0000:02:00.0: Loaded firmware version: 15.32.2.9 iwl3945 0000:02:00.0: Start IWL Error Log Dump: iwl3945 0000:02:00.0: Status: 0x000202E4, count: 1 iwl3945 0000:02:00.0: Desc Time asrtPC blink2 ilink1 nmiPC Line iwl3945 0000:02:00.0: SYSASSERT (0x5) 0000208934 0x008B6 0x0035E 0x00320 0x00000 267 iwl3945 0000:02:00.0: Error Reply type 0x00000001 cmd Reported-by: Zdenek Kabelac Reported-by: Krzysztof Kolasa Reported-by: Pedro Francisco Signed-off-by: Stanislaw Gruszka Signed-off-by: John W. Linville --- drivers/net/wireless/iwlegacy/3945-mac.c | 22 ++++++++++++---------- 1 file changed, 12 insertions(+), 10 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlegacy/3945-mac.c b/drivers/net/wireless/iwlegacy/3945-mac.c index 3630a41df50d..c353b5f19c8c 100644 --- a/drivers/net/wireless/iwlegacy/3945-mac.c +++ b/drivers/net/wireless/iwlegacy/3945-mac.c @@ -475,6 +475,7 @@ il3945_tx_skb(struct il_priv *il, dma_addr_t txcmd_phys; int txq_id = skb_get_queue_mapping(skb); u16 len, idx, hdr_len; + u16 firstlen, secondlen; u8 id; u8 unicast; u8 sta_id; @@ -589,21 +590,22 @@ il3945_tx_skb(struct il_priv *il, len = sizeof(struct il3945_tx_cmd) + sizeof(struct il_cmd_header) + hdr_len; - len = (len + 3) & ~3; + firstlen = (len + 3) & ~3; /* Physical address of this Tx command's header (not MAC header!), * within command buffer array. */ txcmd_phys = - pci_map_single(il->pci_dev, &out_cmd->hdr, len, PCI_DMA_TODEVICE); + pci_map_single(il->pci_dev, &out_cmd->hdr, firstlen, + PCI_DMA_TODEVICE); if (unlikely(pci_dma_mapping_error(il->pci_dev, txcmd_phys))) goto drop_unlock; /* Set up TFD's 2nd entry to point directly to remainder of skb, * if any (802.11 null frames have no payload). */ - len = skb->len - hdr_len; - if (len) { + secondlen = skb->len - hdr_len; + if (secondlen > 0) { phys_addr = - pci_map_single(il->pci_dev, skb->data + hdr_len, len, + pci_map_single(il->pci_dev, skb->data + hdr_len, secondlen, PCI_DMA_TODEVICE); if (unlikely(pci_dma_mapping_error(il->pci_dev, phys_addr))) goto drop_unlock; @@ -611,12 +613,12 @@ il3945_tx_skb(struct il_priv *il, /* Add buffer containing Tx command and MAC(!) header to TFD's * first entry */ - il->ops->txq_attach_buf_to_tfd(il, txq, txcmd_phys, len, 1, 0); + il->ops->txq_attach_buf_to_tfd(il, txq, txcmd_phys, firstlen, 1, 0); dma_unmap_addr_set(out_meta, mapping, txcmd_phys); - dma_unmap_len_set(out_meta, len, len); - if (len) - il->ops->txq_attach_buf_to_tfd(il, txq, phys_addr, len, 0, - U32_PAD(len)); + dma_unmap_len_set(out_meta, len, firstlen); + if (secondlen > 0) + il->ops->txq_attach_buf_to_tfd(il, txq, phys_addr, secondlen, 0, + U32_PAD(secondlen)); if (!ieee80211_has_morefrags(hdr->frame_control)) { txq->need_update = 1; -- cgit v1.2.3-58-ga151 From 74632d11a133b5baf6b9d622dd19d2f944d93d94 Mon Sep 17 00:00:00 2001 From: Felix Fietkau Date: Fri, 15 Mar 2013 14:53:31 +0100 Subject: ath9k_hw: revert chainmask to user configuration after calibration The commit 'ath9k_hw: fix calibration issues on chainmask that don't include chain 0' changed the hardware chainmask to the chip chainmask for the duration of the calibration, but the revert to user configuration in the reset path runs too early. That causes some issues with limiting the number of antennas (including spurious failure in hardware-generated packets). Fix this by reverting the chainmask after the essential parts of the calibration that need the workaround, and before NF calibration is run. Signed-off-by: Felix Fietkau Reported-by: Wojciech Dubowik Tested-by: Wojciech Dubowik Cc: stable@vger.kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/ar9003_calib.c | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/ar9003_calib.c b/drivers/net/wireless/ath/ath9k/ar9003_calib.c index 4cc13940c895..f76c3ca07a45 100644 --- a/drivers/net/wireless/ath/ath9k/ar9003_calib.c +++ b/drivers/net/wireless/ath/ath9k/ar9003_calib.c @@ -1023,6 +1023,7 @@ static bool ar9003_hw_init_cal(struct ath_hw *ah, AR_PHY_AGC_CONTROL_FLTR_CAL | AR_PHY_AGC_CONTROL_PKDET_CAL; + /* Use chip chainmask only for calibration */ ar9003_hw_set_chain_masks(ah, ah->caps.rx_chainmask, ah->caps.tx_chainmask); if (rtt) { @@ -1150,6 +1151,9 @@ skip_tx_iqcal: ar9003_hw_rtt_disable(ah); } + /* Revert chainmask to runtime parameters */ + ar9003_hw_set_chain_masks(ah, ah->rxchainmask, ah->txchainmask); + /* Initialize list pointers */ ah->cal_list = ah->cal_list_last = ah->cal_list_curr = NULL; -- cgit v1.2.3-58-ga151 From 01d4ab96d2e7fceaad204e5a8710ce34e229b8c5 Mon Sep 17 00:00:00 2001 From: Felix Fietkau Date: Fri, 15 Mar 2013 16:18:44 +0100 Subject: ath9k: limit tx path hang check to normal data queues The beacon and multicast-buffer queues are managed by the beacon tasklet, and the generic tx path hang check does not help in any way here. Running it on those queues anyway can introduce some race conditions leading to unnecessary chip resets. Cc: stable@vger.kernel.org Signed-off-by: Felix Fietkau Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/link.c | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/link.c b/drivers/net/wireless/ath/ath9k/link.c index ade3afb21f91..39c84ecf6a42 100644 --- a/drivers/net/wireless/ath/ath9k/link.c +++ b/drivers/net/wireless/ath/ath9k/link.c @@ -28,21 +28,21 @@ void ath_tx_complete_poll_work(struct work_struct *work) int i; bool needreset = false; - for (i = 0; i < ATH9K_NUM_TX_QUEUES; i++) - if (ATH_TXQ_SETUP(sc, i)) { - txq = &sc->tx.txq[i]; - ath_txq_lock(sc, txq); - if (txq->axq_depth) { - if (txq->axq_tx_inprogress) { - needreset = true; - ath_txq_unlock(sc, txq); - break; - } else { - txq->axq_tx_inprogress = true; - } + for (i = 0; i < IEEE80211_NUM_ACS; i++) { + txq = sc->tx.txq_map[i]; + + ath_txq_lock(sc, txq); + if (txq->axq_depth) { + if (txq->axq_tx_inprogress) { + needreset = true; + ath_txq_unlock(sc, txq); + break; + } else { + txq->axq_tx_inprogress = true; } - ath_txq_unlock_complete(sc, txq); } + ath_txq_unlock_complete(sc, txq); + } if (needreset) { ath_dbg(ath9k_hw_common(sc->sc_ah), RESET, -- cgit v1.2.3-58-ga151 From 00d7ea11ff0783e24fe70778f3141270b561aaa1 Mon Sep 17 00:00:00 2001 From: Amitkumar Karwar Date: Fri, 15 Mar 2013 18:47:05 -0700 Subject: mwifiex: fix race when queuing commands Running the following script repeatedly on XO-4 with SD8787 produces command timeout and system lockup. insmod mwifiex_sdio.ko sleep 1 ifconfig eth0 up iwlist eth0 scan & sleep 0.5 rmmod mwifiex_sdio mwifiex_send_cmd_async() is called for sync as well as async commands. (mwifiex_send_cmd_sync() internally calls it for sync command.) "adapter->cmd_queued" gets filled inside mwifiex_send_cmd_async() routine for both types of commands. But it is used only for sync commands in mwifiex_wait_queue_complete(). This could lead to a race when two threads try to queue a sync command with another sync/async command simultaneously. Get rid of global variable and pass command node as a parameter to mwifiex_wait_queue_complete() to fix the problem. Cc: # 3.8 Reported-by: Daniel Drake Tested-by: Daniel Drake Tested-by: Marco Cesarano Signed-off-by: Amitkumar Karwar Signed-off-by: Bing Zhao Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/cmdevt.c | 5 ++--- drivers/net/wireless/mwifiex/main.h | 4 ++-- drivers/net/wireless/mwifiex/scan.c | 8 ++++---- drivers/net/wireless/mwifiex/sta_ioctl.c | 10 ++-------- 4 files changed, 10 insertions(+), 17 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/cmdevt.c b/drivers/net/wireless/mwifiex/cmdevt.c index 20a6c5555873..2ffabddbcfca 100644 --- a/drivers/net/wireless/mwifiex/cmdevt.c +++ b/drivers/net/wireless/mwifiex/cmdevt.c @@ -484,8 +484,6 @@ int mwifiex_send_cmd_sync(struct mwifiex_private *priv, uint16_t cmd_no, ret = mwifiex_send_cmd_async(priv, cmd_no, cmd_action, cmd_oid, data_buf); - if (!ret) - ret = mwifiex_wait_queue_complete(adapter); return ret; } @@ -588,9 +586,10 @@ int mwifiex_send_cmd_async(struct mwifiex_private *priv, uint16_t cmd_no, if (cmd_no == HostCmd_CMD_802_11_SCAN) { mwifiex_queue_scan_cmd(priv, cmd_node); } else { - adapter->cmd_queued = cmd_node; mwifiex_insert_cmd_to_pending_q(adapter, cmd_node, true); queue_work(adapter->workqueue, &adapter->main_work); + if (cmd_node->wait_q_enabled) + ret = mwifiex_wait_queue_complete(adapter, cmd_node); } return ret; diff --git a/drivers/net/wireless/mwifiex/main.h b/drivers/net/wireless/mwifiex/main.h index 553adfb0aa81..7035ade9af74 100644 --- a/drivers/net/wireless/mwifiex/main.h +++ b/drivers/net/wireless/mwifiex/main.h @@ -723,7 +723,6 @@ struct mwifiex_adapter { u16 cmd_wait_q_required; struct mwifiex_wait_queue cmd_wait_q; u8 scan_wait_q_woken; - struct cmd_ctrl_node *cmd_queued; spinlock_t queue_lock; /* lock for tx queues */ struct completion fw_load; u8 country_code[IEEE80211_COUNTRY_STRING_LEN]; @@ -1018,7 +1017,8 @@ int mwifiex_request_set_multicast_list(struct mwifiex_private *priv, struct mwifiex_multicast_list *mcast_list); int mwifiex_copy_mcast_addr(struct mwifiex_multicast_list *mlist, struct net_device *dev); -int mwifiex_wait_queue_complete(struct mwifiex_adapter *adapter); +int mwifiex_wait_queue_complete(struct mwifiex_adapter *adapter, + struct cmd_ctrl_node *cmd_queued); int mwifiex_bss_start(struct mwifiex_private *priv, struct cfg80211_bss *bss, struct cfg80211_ssid *req_ssid); int mwifiex_cancel_hs(struct mwifiex_private *priv, int cmd_type); diff --git a/drivers/net/wireless/mwifiex/scan.c b/drivers/net/wireless/mwifiex/scan.c index bb60c2754a97..d215b4d3c51b 100644 --- a/drivers/net/wireless/mwifiex/scan.c +++ b/drivers/net/wireless/mwifiex/scan.c @@ -1388,10 +1388,13 @@ int mwifiex_scan_networks(struct mwifiex_private *priv, list_del(&cmd_node->list); spin_unlock_irqrestore(&adapter->scan_pending_q_lock, flags); - adapter->cmd_queued = cmd_node; mwifiex_insert_cmd_to_pending_q(adapter, cmd_node, true); queue_work(adapter->workqueue, &adapter->main_work); + + /* Perform internal scan synchronously */ + if (!priv->scan_request) + mwifiex_wait_queue_complete(adapter, cmd_node); } else { spin_unlock_irqrestore(&adapter->scan_pending_q_lock, flags); @@ -1946,9 +1949,6 @@ int mwifiex_request_scan(struct mwifiex_private *priv, /* Normal scan */ ret = mwifiex_scan_networks(priv, NULL); - if (!ret) - ret = mwifiex_wait_queue_complete(priv->adapter); - up(&priv->async_sem); return ret; diff --git a/drivers/net/wireless/mwifiex/sta_ioctl.c b/drivers/net/wireless/mwifiex/sta_ioctl.c index 9f33c92c90f5..13100f8de3db 100644 --- a/drivers/net/wireless/mwifiex/sta_ioctl.c +++ b/drivers/net/wireless/mwifiex/sta_ioctl.c @@ -54,16 +54,10 @@ int mwifiex_copy_mcast_addr(struct mwifiex_multicast_list *mlist, * This function waits on a cmd wait queue. It also cancels the pending * request after waking up, in case of errors. */ -int mwifiex_wait_queue_complete(struct mwifiex_adapter *adapter) +int mwifiex_wait_queue_complete(struct mwifiex_adapter *adapter, + struct cmd_ctrl_node *cmd_queued) { int status; - struct cmd_ctrl_node *cmd_queued; - - if (!adapter->cmd_queued) - return 0; - - cmd_queued = adapter->cmd_queued; - adapter->cmd_queued = NULL; dev_dbg(adapter->dev, "cmd pending\n"); atomic_inc(&adapter->cmd_pending); -- cgit v1.2.3-58-ga151 From a3e240cacc93a06bff3313e28938e980d01a2160 Mon Sep 17 00:00:00 2001 From: Bing Zhao Date: Fri, 15 Mar 2013 18:47:06 -0700 Subject: mwifiex: skip pending commands after function shutdown During rmmod mwifiex_sdio processing FUNC_SHUTDOWN command is sent to firmware. Firmware expcets only FUNC_INIT once WLAN function is shut down. Any command pending in the command queue should be ignored and freed. Cc: # 3.8 Tested-by: Daniel Drake Tested-by: Marco Cesarano Signed-off-by: Bing Zhao Signed-off-by: Amitkumar Karwar Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/cmdevt.c | 17 ++++++++++++++--- 1 file changed, 14 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/cmdevt.c b/drivers/net/wireless/mwifiex/cmdevt.c index 2ffabddbcfca..b5c8b962ce12 100644 --- a/drivers/net/wireless/mwifiex/cmdevt.c +++ b/drivers/net/wireless/mwifiex/cmdevt.c @@ -157,6 +157,20 @@ static int mwifiex_dnld_cmd_to_fw(struct mwifiex_private *priv, return -1; } + cmd_code = le16_to_cpu(host_cmd->command); + cmd_size = le16_to_cpu(host_cmd->size); + + if (adapter->hw_status == MWIFIEX_HW_STATUS_RESET && + cmd_code != HostCmd_CMD_FUNC_SHUTDOWN && + cmd_code != HostCmd_CMD_FUNC_INIT) { + dev_err(adapter->dev, + "DNLD_CMD: FW in reset state, ignore cmd %#x\n", + cmd_code); + mwifiex_complete_cmd(adapter, cmd_node); + mwifiex_insert_cmd_to_free_q(adapter, cmd_node); + return -1; + } + /* Set command sequence number */ adapter->seq_num++; host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO @@ -168,9 +182,6 @@ static int mwifiex_dnld_cmd_to_fw(struct mwifiex_private *priv, adapter->curr_cmd = cmd_node; spin_unlock_irqrestore(&adapter->mwifiex_cmd_lock, flags); - cmd_code = le16_to_cpu(host_cmd->command); - cmd_size = le16_to_cpu(host_cmd->size); - /* Adjust skb length */ if (cmd_node->cmd_skb->len > cmd_size) /* -- cgit v1.2.3-58-ga151 From 084c7189acb3f969c855536166042e27f5dd703f Mon Sep 17 00:00:00 2001 From: Bing Zhao Date: Fri, 15 Mar 2013 18:47:07 -0700 Subject: mwifiex: cancel cmd timer and free curr_cmd in shutdown process curr_cmd points to the command that is in processing or waiting for its command response from firmware. If the function shutdown happens to occur at this time we should cancel the cmd timer and put the command back to free queue. Cc: # 3.8 Tested-by: Marco Cesarano Signed-off-by: Bing Zhao Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/init.c | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/init.c b/drivers/net/wireless/mwifiex/init.c index e38aa9b3663d..0ff4c37ab42a 100644 --- a/drivers/net/wireless/mwifiex/init.c +++ b/drivers/net/wireless/mwifiex/init.c @@ -709,6 +709,14 @@ mwifiex_shutdown_drv(struct mwifiex_adapter *adapter) return ret; } + /* cancel current command */ + if (adapter->curr_cmd) { + dev_warn(adapter->dev, "curr_cmd is still in processing\n"); + del_timer(&adapter->cmd_timer); + mwifiex_insert_cmd_to_free_q(adapter, adapter->curr_cmd); + adapter->curr_cmd = NULL; + } + /* shut down mwifiex */ dev_dbg(adapter->dev, "info: shutdown mwifiex...\n"); -- cgit v1.2.3-58-ga151 From 36ef0b473fbf43d5db23eea4616cc1d18cec245f Mon Sep 17 00:00:00 2001 From: Jussi Kivilinna Date: Sun, 17 Mar 2013 11:54:04 +0200 Subject: rtlwifi: usb: add missing freeing of skbuff Signed-off-by: Jussi Kivilinna Acked-by: Larry Finger Cc: stable@vger.kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/rtlwifi/usb.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/rtlwifi/usb.c b/drivers/net/wireless/rtlwifi/usb.c index 156b52732f3d..5847d6d0881e 100644 --- a/drivers/net/wireless/rtlwifi/usb.c +++ b/drivers/net/wireless/rtlwifi/usb.c @@ -851,6 +851,7 @@ static void _rtl_usb_transmit(struct ieee80211_hw *hw, struct sk_buff *skb, if (unlikely(!_urb)) { RT_TRACE(rtlpriv, COMP_ERR, DBG_EMERG, "Can't allocate urb. Drop skb!\n"); + kfree_skb(skb); return; } _rtl_submit_tx_urb(hw, _urb); -- cgit v1.2.3-58-ga151 From cc904c7188c29847817f35e6966fec3014c7479b Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Thu, 14 Mar 2013 08:35:06 +0200 Subject: iwlwifi: fix length check in multi-TB HCMD As reported by Ben Hutchings, there was a harmless issue in the checks being done on the lengths of the TBs while building the TFD for a multi-TB host command. Cc: stable@vger@kernel.org Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/pcie/tx.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/pcie/tx.c b/drivers/net/wireless/iwlwifi/pcie/tx.c index 8595c16f74de..cb5c6792e3a8 100644 --- a/drivers/net/wireless/iwlwifi/pcie/tx.c +++ b/drivers/net/wireless/iwlwifi/pcie/tx.c @@ -1264,7 +1264,7 @@ static int iwl_pcie_enqueue_hcmd(struct iwl_trans *trans, for (i = 0; i < IWL_MAX_CMD_TBS_PER_TFD; i++) { int copy = 0; - if (!cmd->len) + if (!cmd->len[i]) continue; /* need at least IWL_HCMD_SCRATCHBUF_SIZE copied */ -- cgit v1.2.3-58-ga151 From 4620020b5d7ca34d1c03fa98b0ca457320cb7d71 Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Wed, 13 Mar 2013 16:38:32 +0200 Subject: iwlwifi: set rfkill in internal state of the transport We didn't update the internal of the PCIe transport when we read the RFkill state directly. Fix that. Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/pcie/trans.c | 13 +++++++++++++ 1 file changed, 13 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/pcie/trans.c b/drivers/net/wireless/iwlwifi/pcie/trans.c index 17bedc50e753..12c4f31ca8fb 100644 --- a/drivers/net/wireless/iwlwifi/pcie/trans.c +++ b/drivers/net/wireless/iwlwifi/pcie/trans.c @@ -475,6 +475,10 @@ static int iwl_trans_pcie_start_fw(struct iwl_trans *trans, /* If platform's RF_KILL switch is NOT set to KILL */ hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); if (hw_rfkill && !run_in_rfkill) return -ERFKILL; @@ -641,6 +645,7 @@ static int iwl_trans_pcie_d3_resume(struct iwl_trans *trans, static int iwl_trans_pcie_start_hw(struct iwl_trans *trans) { + struct iwl_trans_pcie *trans_pcie = IWL_TRANS_GET_PCIE_TRANS(trans); bool hw_rfkill; int err; @@ -656,6 +661,10 @@ static int iwl_trans_pcie_start_hw(struct iwl_trans *trans) iwl_enable_rfkill_int(trans); hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); return 0; @@ -694,6 +703,10 @@ static void iwl_trans_pcie_stop_hw(struct iwl_trans *trans, * op_mode. */ hw_rfkill = iwl_is_rfkill_set(trans); + if (hw_rfkill) + set_bit(STATUS_RFKILL, &trans_pcie->status); + else + clear_bit(STATUS_RFKILL, &trans_pcie->status); iwl_op_mode_hw_rf_kill(trans->op_mode, hw_rfkill); } } -- cgit v1.2.3-58-ga151 From 2d5d50ee596361566f7f84300117cba7d7672bc5 Mon Sep 17 00:00:00 2001 From: Emmanuel Grumbach Date: Thu, 31 Jan 2013 15:03:55 +0200 Subject: iwlwifi: dvm: don't send HCMD in restart flow There is a race between the restart flow and the workers. The workers are cancelled after the fw is already killed and might send HCMD when there is fw to handle them. Simply check that there is a fw to which the HCMD can be sent before actually sending it. Cc: stable@vger.kernel.org Signed-off-by: Emmanuel Grumbach Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/dvm/lib.c | 9 +++++++++ drivers/net/wireless/iwlwifi/dvm/ucode.c | 4 ++-- 2 files changed, 11 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/dvm/lib.c b/drivers/net/wireless/iwlwifi/dvm/lib.c index 86ea5f4c3939..44ca0e57f9f7 100644 --- a/drivers/net/wireless/iwlwifi/dvm/lib.c +++ b/drivers/net/wireless/iwlwifi/dvm/lib.c @@ -1261,6 +1261,15 @@ int iwl_dvm_send_cmd(struct iwl_priv *priv, struct iwl_host_cmd *cmd) return -EIO; } + /* + * This can happen upon FW ASSERT: we clear the STATUS_FW_ERROR flag + * in iwl_down but cancel the workers only later. + */ + if (!priv->ucode_loaded) { + IWL_ERR(priv, "Fw not loaded - dropping CMD: %x\n", cmd->id); + return -EIO; + } + /* * Synchronous commands from this op-mode must hold * the mutex, this ensures we don't try to send two diff --git a/drivers/net/wireless/iwlwifi/dvm/ucode.c b/drivers/net/wireless/iwlwifi/dvm/ucode.c index 736fe9bb140e..1a4ac9236a44 100644 --- a/drivers/net/wireless/iwlwifi/dvm/ucode.c +++ b/drivers/net/wireless/iwlwifi/dvm/ucode.c @@ -367,6 +367,8 @@ int iwl_load_ucode_wait_alive(struct iwl_priv *priv, return -EIO; } + priv->ucode_loaded = true; + if (ucode_type != IWL_UCODE_WOWLAN) { /* delay a bit to give rfkill time to run */ msleep(5); @@ -380,8 +382,6 @@ int iwl_load_ucode_wait_alive(struct iwl_priv *priv, return ret; } - priv->ucode_loaded = true; - return 0; } -- cgit v1.2.3-58-ga151 From 0582b7d15f8a7ae53dd2128b8eb01567b3fd2277 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Tue, 19 Mar 2013 13:40:23 +0000 Subject: sh_eth: fix bitbang memory leak sh_mdio_init() allocates pointer to 'struct bb_info' but only stores it locally, so that sh_mdio_release() can't free it on driver unload. Add the pointer to 'struct bb_info' to 'struct sh_eth_private', so that sh_mdio_init() can save 'bitbang' variable for sh_mdio_release() to be able to free it later... Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 5 +++++ drivers/net/ethernet/renesas/sh_eth.h | 1 + 2 files changed, 6 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 33e96176e4d8..c87862812ead 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -2220,6 +2220,7 @@ static void sh_eth_tsu_init(struct sh_eth_private *mdp) /* MDIO bus release function */ static int sh_mdio_release(struct net_device *ndev) { + struct sh_eth_private *mdp = netdev_priv(ndev); struct mii_bus *bus = dev_get_drvdata(&ndev->dev); /* unregister mdio bus */ @@ -2234,6 +2235,9 @@ static int sh_mdio_release(struct net_device *ndev) /* free bitbang info */ free_mdio_bitbang(bus); + /* free bitbang memory */ + kfree(mdp->bitbang); + return 0; } @@ -2262,6 +2266,7 @@ static int sh_mdio_init(struct net_device *ndev, int id, bitbang->ctrl.ops = &bb_ops; /* MII controller setting */ + mdp->bitbang = bitbang; mdp->mii_bus = alloc_mdio_bitbang(&bitbang->ctrl); if (!mdp->mii_bus) { ret = -ENOMEM; diff --git a/drivers/net/ethernet/renesas/sh_eth.h b/drivers/net/ethernet/renesas/sh_eth.h index bae84fd2e73a..e6655678458e 100644 --- a/drivers/net/ethernet/renesas/sh_eth.h +++ b/drivers/net/ethernet/renesas/sh_eth.h @@ -705,6 +705,7 @@ struct sh_eth_private { const u16 *reg_offset; void __iomem *addr; void __iomem *tsu_addr; + struct bb_info *bitbang; u32 num_rx_ring; u32 num_tx_ring; dma_addr_t rx_desc_dma; -- cgit v1.2.3-58-ga151 From fc0c0900408e05758a0df17c1924ca837fafca5e Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Tue, 19 Mar 2013 13:41:32 +0000 Subject: sh_eth: check TSU registers ioremap() error One must check the result of ioremap() -- in this case it prevents potential kernel oops when initializing TSU registers further on... Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index c87862812ead..bf5e3cf97c4d 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -2446,6 +2446,11 @@ static int sh_eth_drv_probe(struct platform_device *pdev) } mdp->tsu_addr = ioremap(rtsu->start, resource_size(rtsu)); + if (mdp->tsu_addr == NULL) { + ret = -ENOMEM; + dev_err(&pdev->dev, "TSU ioremap failed.\n"); + goto out_release; + } mdp->port = devno % 2; ndev->features = NETIF_F_HW_VLAN_FILTER; } -- cgit v1.2.3-58-ga151 From fa90b077d72b4ea92706e86fdff7b5dca294caa3 Mon Sep 17 00:00:00 2001 From: Wei Yongjun Date: Wed, 20 Mar 2013 02:21:48 +0000 Subject: lpc_eth: fix error return code in lpc_eth_drv_probe() Fix to return a negative error code from the error handling case instead of 0, as returned elsewhere in this function. Signed-off-by: Wei Yongjun Signed-off-by: David S. Miller --- drivers/net/ethernet/nxp/lpc_eth.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/nxp/lpc_eth.c b/drivers/net/ethernet/nxp/lpc_eth.c index c4122c86f829..efa29b712d5f 100644 --- a/drivers/net/ethernet/nxp/lpc_eth.c +++ b/drivers/net/ethernet/nxp/lpc_eth.c @@ -1472,7 +1472,8 @@ static int lpc_eth_drv_probe(struct platform_device *pdev) } platform_set_drvdata(pdev, ndev); - if (lpc_mii_init(pldat) != 0) + ret = lpc_mii_init(pldat); + if (ret) goto err_out_unregister_netdev; netdev_info(ndev, "LPC mac at 0x%08x irq %d\n", -- cgit v1.2.3-58-ga151 From da2191e31409d1058dcbed44e8f53e39a40e86b3 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 20 Mar 2013 12:31:07 -0300 Subject: net: fec: Define indexes as 'unsigned int' Fix the following warnings that happen when building with W=1 option: drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_free_buffers': drivers/net/ethernet/freescale/fec.c:1337:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_alloc_buffers': drivers/net/ethernet/freescale/fec.c:1361:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] drivers/net/ethernet/freescale/fec.c: In function 'fec_enet_init': drivers/net/ethernet/freescale/fec.c:1631:16: warning: comparison between signed and unsigned integer expressions [-Wsign-compare] Signed-off-by: Fabio Estevam Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec.c | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/freescale/fec.c b/drivers/net/ethernet/freescale/fec.c index e3f39372ce25..911d0253dbb2 100644 --- a/drivers/net/ethernet/freescale/fec.c +++ b/drivers/net/ethernet/freescale/fec.c @@ -1332,7 +1332,7 @@ static int fec_enet_ioctl(struct net_device *ndev, struct ifreq *rq, int cmd) static void fec_enet_free_buffers(struct net_device *ndev) { struct fec_enet_private *fep = netdev_priv(ndev); - int i; + unsigned int i; struct sk_buff *skb; struct bufdesc *bdp; @@ -1356,7 +1356,7 @@ static void fec_enet_free_buffers(struct net_device *ndev) static int fec_enet_alloc_buffers(struct net_device *ndev) { struct fec_enet_private *fep = netdev_priv(ndev); - int i; + unsigned int i; struct sk_buff *skb; struct bufdesc *bdp; @@ -1598,7 +1598,7 @@ static int fec_enet_init(struct net_device *ndev) struct fec_enet_private *fep = netdev_priv(ndev); struct bufdesc *cbd_base; struct bufdesc *bdp; - int i; + unsigned int i; /* Allocate memory for buffer descriptors. */ cbd_base = dma_alloc_coherent(NULL, PAGE_SIZE, &fep->bd_dma, -- cgit v1.2.3-58-ga151 From 9d73adf431e093b23fb4990f1ade11283cb67a98 Mon Sep 17 00:00:00 2001 From: Fabio Estevam Date: Wed, 20 Mar 2013 08:19:32 +0000 Subject: fec: Fix the build as module Since commit ff43da86c69 (NET: FEC: dynamtic check DMA desc buff type) the following build error happens when CONFIG_FEC=m ERROR: "fec_ptp_init" [drivers/net/ethernet/freescale/fec.ko] undefined! ERROR: "fec_ptp_ioctl" [drivers/net/ethernet/freescale/fec.ko] undefined! ERROR: "fec_ptp_start_cyclecounter" [drivers/net/ethernet/freescale/fec.ko] undefined! Fix it by exporting the required fec_ptp symbols. Reported-by: Uwe Kleine-Koenig Signed-off-by: Fabio Estevam Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec_ptp.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/freescale/fec_ptp.c b/drivers/net/ethernet/freescale/fec_ptp.c index 1f17ca0f2201..0d8df400a479 100644 --- a/drivers/net/ethernet/freescale/fec_ptp.c +++ b/drivers/net/ethernet/freescale/fec_ptp.c @@ -128,6 +128,7 @@ void fec_ptp_start_cyclecounter(struct net_device *ndev) spin_unlock_irqrestore(&fep->tmreg_lock, flags); } +EXPORT_SYMBOL(fec_ptp_start_cyclecounter); /** * fec_ptp_adjfreq - adjust ptp cycle frequency @@ -318,6 +319,7 @@ int fec_ptp_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd) return copy_to_user(ifr->ifr_data, &config, sizeof(config)) ? -EFAULT : 0; } +EXPORT_SYMBOL(fec_ptp_ioctl); /** * fec_time_keep - call timecounter_read every second to avoid timer overrun @@ -383,3 +385,4 @@ void fec_ptp_init(struct net_device *ndev, struct platform_device *pdev) pr_info("registered PHC device on %s\n", ndev->name); } } +EXPORT_SYMBOL(fec_ptp_init); -- cgit v1.2.3-58-ga151 From cb0e51d80694fc9964436be1a1a15275e991cb1e Mon Sep 17 00:00:00 2001 From: Wei Yongjun Date: Wed, 20 Mar 2013 21:31:42 +0000 Subject: lantiq_etop: use free_netdev(netdev) instead of kfree() Freeing netdev without free_netdev() leads to net, tx leaks. And it may lead to dereferencing freed pointer. Signed-off-by: Wei Yongjun Signed-off-by: David S. Miller --- drivers/net/ethernet/lantiq_etop.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/lantiq_etop.c b/drivers/net/ethernet/lantiq_etop.c index 6a2127489af7..bfdb06860397 100644 --- a/drivers/net/ethernet/lantiq_etop.c +++ b/drivers/net/ethernet/lantiq_etop.c @@ -769,7 +769,7 @@ ltq_etop_probe(struct platform_device *pdev) return 0; err_free: - kfree(dev); + free_netdev(dev); err_out: return err; } -- cgit v1.2.3-58-ga151 From ce16294fda230c787ce5c35f61b2f80d14d70a72 Mon Sep 17 00:00:00 2001 From: Lothar Waßmann Date: Thu, 21 Mar 2013 02:20:11 +0000 Subject: net: ethernet: cpsw: fix erroneous condition in error check MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The error check in cpsw_probe_dt() has an '&&' where an '||' is meant to be. This causes a NULL pointer dereference when incomplet DT data is passed to the driver ('phy_id' property for cpsw_emac1 missing). Signed-off-by: Lothar Waßmann Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index 75c48558e6fd..df32a090d08e 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -1364,7 +1364,7 @@ static int cpsw_probe_dt(struct cpsw_platform_data *data, struct platform_device *mdio; parp = of_get_property(slave_node, "phy_id", &lenp); - if ((parp == NULL) && (lenp != (sizeof(void *) * 2))) { + if ((parp == NULL) || (lenp != (sizeof(void *) * 2))) { pr_err("Missing slave[%d] phy_id property\n", i); ret = -EINVAL; goto error_ret; -- cgit v1.2.3-58-ga151 From c101c81b5293cdcb616ed4948d0c4a4cfd1f481a Mon Sep 17 00:00:00 2001 From: Moshe Lazer Date: Thu, 21 Mar 2013 05:55:51 +0000 Subject: net/mlx4_core: Fix wrong mask applied on EQ numbers in the wrapper Currently the mask is wrongly set in the MAP_EQ wrapper, fix that. Without the fix any EQ number above 511 is mapped to one below 511. Signed-off-by: Moshe Lazer Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/eq.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/mellanox/mlx4/eq.c b/drivers/net/ethernet/mellanox/mlx4/eq.c index 251ae2f93116..8e3123a1df88 100644 --- a/drivers/net/ethernet/mellanox/mlx4/eq.c +++ b/drivers/net/ethernet/mellanox/mlx4/eq.c @@ -771,7 +771,7 @@ int mlx4_MAP_EQ_wrapper(struct mlx4_dev *dev, int slave, struct mlx4_slave_event_eq_info *event_eq = priv->mfunc.master.slave_state[slave].event_eq; u32 in_modifier = vhcr->in_modifier; - u32 eqn = in_modifier & 0x1FF; + u32 eqn = in_modifier & 0x3FF; u64 in_param = vhcr->in_param; int err = 0; int i; -- cgit v1.2.3-58-ga151 From 80cb0021163cb55b14c7c054073f89d63a2e1e40 Mon Sep 17 00:00:00 2001 From: Hadar Hen Zion Date: Thu, 21 Mar 2013 05:55:52 +0000 Subject: net/mlx4_core: Fix wrong order of flow steering resources removal On the resource tracker cleanup flow, the DMFS rules must be deleted before we destroy the QPs, else the HW may attempt doing packet steering to non existent QPs. Signed-off-by: Hadar Hen Zion Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/resource_tracker.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c index 2995687f1aee..0d1d9679179c 100644 --- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c +++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c @@ -3806,6 +3806,7 @@ void mlx4_delete_all_resources_for_slave(struct mlx4_dev *dev, int slave) mutex_lock(&priv->mfunc.master.res_tracker.slave_list[slave].mutex); /*VLAN*/ rem_slave_macs(dev, slave); + rem_slave_fs_rule(dev, slave); rem_slave_qps(dev, slave); rem_slave_srqs(dev, slave); rem_slave_cqs(dev, slave); @@ -3814,6 +3815,5 @@ void mlx4_delete_all_resources_for_slave(struct mlx4_dev *dev, int slave) rem_slave_mtts(dev, slave); rem_slave_counters(dev, slave); rem_slave_xrcdns(dev, slave); - rem_slave_fs_rule(dev, slave); mutex_unlock(&priv->mfunc.master.res_tracker.slave_list[slave].mutex); } -- cgit v1.2.3-58-ga151 From 6efb5fac4d6b617972ab5a10bf67e0eba2c2d212 Mon Sep 17 00:00:00 2001 From: Hadar Hen Zion Date: Thu, 21 Mar 2013 05:55:53 +0000 Subject: net/mlx4_en: Remove ethtool flow steering rules before releasing QPs Fix the ethtool flow steering rules cleanup to be carried out before releasing the RX QPs. Signed-off-by: Hadar Hen Zion Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 22 +++++++++++----------- 1 file changed, 11 insertions(+), 11 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c index 995d4b6d5c1e..f278b10ef714 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c @@ -1637,6 +1637,17 @@ void mlx4_en_stop_port(struct net_device *dev, int detach) /* Flush multicast filter */ mlx4_SET_MCAST_FLTR(mdev->dev, priv->port, 0, 1, MLX4_MCAST_CONFIG); + /* Remove flow steering rules for the port*/ + if (mdev->dev->caps.steering_mode == + MLX4_STEERING_MODE_DEVICE_MANAGED) { + ASSERT_RTNL(); + list_for_each_entry_safe(flow, tmp_flow, + &priv->ethtool_list, list) { + mlx4_flow_detach(mdev->dev, flow->id); + list_del(&flow->list); + } + } + mlx4_en_destroy_drop_qp(priv); /* Free TX Rings */ @@ -1657,17 +1668,6 @@ void mlx4_en_stop_port(struct net_device *dev, int detach) if (!(mdev->dev->caps.flags2 & MLX4_DEV_CAP_FLAGS2_REASSIGN_MAC_EN)) mdev->mac_removed[priv->port] = 1; - /* Remove flow steering rules for the port*/ - if (mdev->dev->caps.steering_mode == - MLX4_STEERING_MODE_DEVICE_MANAGED) { - ASSERT_RTNL(); - list_for_each_entry_safe(flow, tmp_flow, - &priv->ethtool_list, list) { - mlx4_flow_detach(mdev->dev, flow->id); - list_del(&flow->list); - } - } - /* Free RX Rings */ for (i = 0; i < priv->rx_ring_num; i++) { mlx4_en_deactivate_rx_ring(priv, &priv->rx_ring[i]); -- cgit v1.2.3-58-ga151 From 1e3f7b324e46b772dec1bb6dd96ae745fc085401 Mon Sep 17 00:00:00 2001 From: Hadar Hen Zion Date: Thu, 21 Mar 2013 05:55:54 +0000 Subject: net/mlx4_core: Always use 64 bit resource ID when doing lookup One of the resource tracker code paths was wrongly using int and not u64 for resource tracking IDs, fix it. Signed-off-by: Hadar Hen Zion Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/resource_tracker.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c index 0d1d9679179c..b0ccdb55ca46 100644 --- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c +++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c @@ -355,7 +355,7 @@ static int mpt_mask(struct mlx4_dev *dev) return dev->caps.num_mpts - 1; } -static void *find_res(struct mlx4_dev *dev, int res_id, +static void *find_res(struct mlx4_dev *dev, u64 res_id, enum mlx4_resource type) { struct mlx4_priv *priv = mlx4_priv(dev); -- cgit v1.2.3-58-ga151 From 2c473ae7e5826c108e52f4a9d75425fd4c6f9ed1 Mon Sep 17 00:00:00 2001 From: Hadar Hen Zion Date: Thu, 21 Mar 2013 05:55:55 +0000 Subject: net/mlx4_core: Disallow releasing VF QPs which have steering rules VF QPs must not be released when they have steering rules attached to them. For that end, introduce a reference count field to the QP object in the SRIOV resource tracker which is incremented/decremented when steering rules are attached/detached to it. QPs can be released by VF only when their ref count is zero. Signed-off-by: Hadar Hen Zion Signed-off-by: Or Gerlitz Signed-off-by: David S. Miller --- .../net/ethernet/mellanox/mlx4/resource_tracker.c | 41 +++++++++++++++++----- 1 file changed, 33 insertions(+), 8 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c index b0ccdb55ca46..1391b52f443a 100644 --- a/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c +++ b/drivers/net/ethernet/mellanox/mlx4/resource_tracker.c @@ -99,6 +99,7 @@ struct res_qp { struct list_head mcg_list; spinlock_t mcg_spl; int local_qpn; + atomic_t ref_count; }; enum res_mtt_states { @@ -197,6 +198,7 @@ enum res_fs_rule_states { struct res_fs_rule { struct res_common com; + int qpn; }; static void *res_tracker_lookup(struct rb_root *root, u64 res_id) @@ -447,6 +449,7 @@ static struct res_common *alloc_qp_tr(int id) ret->local_qpn = id; INIT_LIST_HEAD(&ret->mcg_list); spin_lock_init(&ret->mcg_spl); + atomic_set(&ret->ref_count, 0); return &ret->com; } @@ -554,7 +557,7 @@ static struct res_common *alloc_xrcdn_tr(int id) return &ret->com; } -static struct res_common *alloc_fs_rule_tr(u64 id) +static struct res_common *alloc_fs_rule_tr(u64 id, int qpn) { struct res_fs_rule *ret; @@ -564,7 +567,7 @@ static struct res_common *alloc_fs_rule_tr(u64 id) ret->com.res_id = id; ret->com.state = RES_FS_RULE_ALLOCATED; - + ret->qpn = qpn; return &ret->com; } @@ -602,7 +605,7 @@ static struct res_common *alloc_tr(u64 id, enum mlx4_resource type, int slave, ret = alloc_xrcdn_tr(id); break; case RES_FS_RULE: - ret = alloc_fs_rule_tr(id); + ret = alloc_fs_rule_tr(id, extra); break; default: return NULL; @@ -671,10 +674,14 @@ undo: static int remove_qp_ok(struct res_qp *res) { - if (res->com.state == RES_QP_BUSY) + if (res->com.state == RES_QP_BUSY || atomic_read(&res->ref_count) || + !list_empty(&res->mcg_list)) { + pr_err("resource tracker: fail to remove qp, state %d, ref_count %d\n", + res->com.state, atomic_read(&res->ref_count)); return -EBUSY; - else if (res->com.state != RES_QP_RESERVED) + } else if (res->com.state != RES_QP_RESERVED) { return -EPERM; + } return 0; } @@ -3124,6 +3131,7 @@ int mlx4_QP_FLOW_STEERING_ATTACH_wrapper(struct mlx4_dev *dev, int slave, struct list_head *rlist = &tracker->slave_list[slave].res_list[RES_MAC]; int err; int qpn; + struct res_qp *rqp; struct mlx4_net_trans_rule_hw_ctrl *ctrl; struct _rule_hw *rule_header; int header_id; @@ -3134,7 +3142,7 @@ int mlx4_QP_FLOW_STEERING_ATTACH_wrapper(struct mlx4_dev *dev, int slave, ctrl = (struct mlx4_net_trans_rule_hw_ctrl *)inbox->buf; qpn = be32_to_cpu(ctrl->qpn) & 0xffffff; - err = get_res(dev, slave, qpn, RES_QP, NULL); + err = get_res(dev, slave, qpn, RES_QP, &rqp); if (err) { pr_err("Steering rule with qpn 0x%x rejected.\n", qpn); return err; @@ -3175,14 +3183,16 @@ int mlx4_QP_FLOW_STEERING_ATTACH_wrapper(struct mlx4_dev *dev, int slave, if (err) goto err_put; - err = add_res_range(dev, slave, vhcr->out_param, 1, RES_FS_RULE, 0); + err = add_res_range(dev, slave, vhcr->out_param, 1, RES_FS_RULE, qpn); if (err) { mlx4_err(dev, "Fail to add flow steering resources.\n "); /* detach rule*/ mlx4_cmd(dev, vhcr->out_param, 0, 0, MLX4_QP_FLOW_STEERING_DETACH, MLX4_CMD_TIME_CLASS_A, MLX4_CMD_NATIVE); + goto err_put; } + atomic_inc(&rqp->ref_count); err_put: put_res(dev, slave, qpn, RES_QP); return err; @@ -3195,20 +3205,35 @@ int mlx4_QP_FLOW_STEERING_DETACH_wrapper(struct mlx4_dev *dev, int slave, struct mlx4_cmd_info *cmd) { int err; + struct res_qp *rqp; + struct res_fs_rule *rrule; if (dev->caps.steering_mode != MLX4_STEERING_MODE_DEVICE_MANAGED) return -EOPNOTSUPP; + err = get_res(dev, slave, vhcr->in_param, RES_FS_RULE, &rrule); + if (err) + return err; + /* Release the rule form busy state before removal */ + put_res(dev, slave, vhcr->in_param, RES_FS_RULE); + err = get_res(dev, slave, rrule->qpn, RES_QP, &rqp); + if (err) + return err; + err = rem_res_range(dev, slave, vhcr->in_param, 1, RES_FS_RULE, 0); if (err) { mlx4_err(dev, "Fail to remove flow steering resources.\n "); - return err; + goto out; } err = mlx4_cmd(dev, vhcr->in_param, 0, 0, MLX4_QP_FLOW_STEERING_DETACH, MLX4_CMD_TIME_CLASS_A, MLX4_CMD_NATIVE); + if (!err) + atomic_dec(&rqp->ref_count); +out: + put_res(dev, slave, rrule->qpn, RES_QP); return err; } -- cgit v1.2.3-58-ga151 From 8fe7f99a9e11a43183bc27420309ae105e1fec1a Mon Sep 17 00:00:00 2001 From: Kumar Amit Mehta Date: Sat, 23 Mar 2013 20:10:25 +0000 Subject: bnx2x: fix assignment of signed expression to unsigned variable fix for incorrect assignment of signed expression to unsigned variable. Signed-off-by: Kumar Amit Mehta Acked-by: Dmitry Kravkov Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c | 18 +++++++++--------- 1 file changed, 9 insertions(+), 9 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c index 568205436a15..91ecd6a00d05 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_dcb.c @@ -2139,12 +2139,12 @@ static u8 bnx2x_dcbnl_get_cap(struct net_device *netdev, int capid, u8 *cap) break; default: BNX2X_ERR("Non valid capability ID\n"); - rval = -EINVAL; + rval = 1; break; } } else { DP(BNX2X_MSG_DCB, "DCB disabled\n"); - rval = -EINVAL; + rval = 1; } DP(BNX2X_MSG_DCB, "capid %d:%x\n", capid, *cap); @@ -2170,12 +2170,12 @@ static int bnx2x_dcbnl_get_numtcs(struct net_device *netdev, int tcid, u8 *num) break; default: BNX2X_ERR("Non valid TC-ID\n"); - rval = -EINVAL; + rval = 1; break; } } else { DP(BNX2X_MSG_DCB, "DCB disabled\n"); - rval = -EINVAL; + rval = 1; } return rval; @@ -2188,7 +2188,7 @@ static int bnx2x_dcbnl_set_numtcs(struct net_device *netdev, int tcid, u8 num) return -EINVAL; } -static u8 bnx2x_dcbnl_get_pfc_state(struct net_device *netdev) +static u8 bnx2x_dcbnl_get_pfc_state(struct net_device *netdev) { struct bnx2x *bp = netdev_priv(netdev); DP(BNX2X_MSG_DCB, "state = %d\n", bp->dcbx_local_feat.pfc.enabled); @@ -2390,12 +2390,12 @@ static u8 bnx2x_dcbnl_get_featcfg(struct net_device *netdev, int featid, break; default: BNX2X_ERR("Non valid featrue-ID\n"); - rval = -EINVAL; + rval = 1; break; } } else { DP(BNX2X_MSG_DCB, "DCB disabled\n"); - rval = -EINVAL; + rval = 1; } return rval; @@ -2431,12 +2431,12 @@ static u8 bnx2x_dcbnl_set_featcfg(struct net_device *netdev, int featid, break; default: BNX2X_ERR("Non valid featrue-ID\n"); - rval = -EINVAL; + rval = 1; break; } } else { DP(BNX2X_MSG_DCB, "dcbnl call not valid\n"); - rval = -EINVAL; + rval = 1; } return rval; -- cgit v1.2.3-58-ga151 From 0f49d64c95944f5701216e900b89aab749edcda2 Mon Sep 17 00:00:00 2001 From: Avinash Patil Date: Wed, 20 Mar 2013 17:56:23 -0700 Subject: mwifiex: reset skb->data after processing PCIe sleep confirm cmd respose This patch is a bug fix for an issue wherein power save was not working for PCIe. This happens because for processing power save sleep confirm command we pull skb so that skb->data points ahead of interface header. We use same skb to get other cmda responses as well. So if we don't push skb after processing cmd response, it results into reduction in skb->len and finally skb->len reaches zero. This causes failure in processing sleep command response. Fix this by pushing skb by INTF_HEADER_LEN at the end of command response processing. Signed-off-by: Avinash Patil Signed-off-by: Bing Zhao Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/pcie.c | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/pcie.c b/drivers/net/wireless/mwifiex/pcie.c index 5c395e2e6a2b..feb204613397 100644 --- a/drivers/net/wireless/mwifiex/pcie.c +++ b/drivers/net/wireless/mwifiex/pcie.c @@ -1508,6 +1508,7 @@ static int mwifiex_pcie_process_cmd_complete(struct mwifiex_adapter *adapter) } memcpy(adapter->upld_buf, skb->data, min_t(u32, MWIFIEX_SIZE_OF_CMD_BUFFER, skb->len)); + skb_push(skb, INTF_HEADER_LEN); if (mwifiex_map_pci_memory(adapter, skb, MWIFIEX_UPLD_SIZE, PCI_DMA_FROMDEVICE)) return -1; -- cgit v1.2.3-58-ga151 From a1f6c6b147cc5e83ec36dab8370bd5ec5fa1def6 Mon Sep 17 00:00:00 2001 From: xunleer Date: Tue, 5 Mar 2013 07:44:20 +0000 Subject: ixgbevf: don't release the soft entries When the ixgbevf driver is opened the request to allocate MSIX irq vectors may fail. In that case the driver will call ixgbevf_down() which will call ixgbevf_irq_disable() to clear the HW interrupt registers and calls synchronize_irq() using the msix_entries pointer in the adapter structure. However, when the function to request the MSIX irq vectors failed it had already freed the msix_entries which causes an OOPs from using the NULL pointer in synchronize_irq(). The calls to pci_disable_msix() and to free the msix_entries memory should not occur if device open fails. Instead they should be called during device driver removal to balance with the call to pci_enable_msix() and the call to allocate msix_entries memory during the device probe and driver load. Signed-off-by: Li Xun Signed-off-by: Greg Rose Tested-by: Sibai Li Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 24 +++++++++++++++++++---- 1 file changed, 20 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c index c3db6cd69b68..2b6cb5ca48ee 100644 --- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c +++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c @@ -944,9 +944,17 @@ free_queue_irqs: free_irq(adapter->msix_entries[vector].vector, adapter->q_vector[vector]); } - pci_disable_msix(adapter->pdev); - kfree(adapter->msix_entries); - adapter->msix_entries = NULL; + /* This failure is non-recoverable - it indicates the system is + * out of MSIX vector resources and the VF driver cannot run + * without them. Set the number of msix vectors to zero + * indicating that not enough can be allocated. The error + * will be returned to the user indicating device open failed. + * Any further attempts to force the driver to open will also + * fail. The only way to recover is to unload the driver and + * reload it again. If the system has recovered some MSIX + * vectors then it may succeed. + */ + adapter->num_msix_vectors = 0; return err; } @@ -2572,6 +2580,15 @@ static int ixgbevf_open(struct net_device *netdev) struct ixgbe_hw *hw = &adapter->hw; int err; + /* A previous failure to open the device because of a lack of + * available MSIX vector resources may have reset the number + * of msix vectors variable to zero. The only way to recover + * is to unload/reload the driver and hope that the system has + * been able to recover some MSIX vector resources. + */ + if (!adapter->num_msix_vectors) + return -ENOMEM; + /* disallow open during test */ if (test_bit(__IXGBEVF_TESTING, &adapter->state)) return -EBUSY; @@ -2628,7 +2645,6 @@ static int ixgbevf_open(struct net_device *netdev) err_req_irq: ixgbevf_down(adapter); - ixgbevf_free_irq(adapter); err_setup_rx: ixgbevf_free_all_rx_resources(adapter); err_setup_tx: -- cgit v1.2.3-58-ga151 From 22c12752d183f39aa8e2cc884cfcb23c0cb6d98d Mon Sep 17 00:00:00 2001 From: Lior Levy Date: Tue, 12 Mar 2013 15:49:32 +0000 Subject: igb: fix i350 anti spoofing config Fix a problem in i350 where anti spoofing configuration was written into a wrong register. Signed-off-by: Lior Levy Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/igb/e1000_82575.c | 33 ++++++++++++++++------------ 1 file changed, 19 insertions(+), 14 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/igb/e1000_82575.c b/drivers/net/ethernet/intel/igb/e1000_82575.c index b64542acfa34..12b1d8480808 100644 --- a/drivers/net/ethernet/intel/igb/e1000_82575.c +++ b/drivers/net/ethernet/intel/igb/e1000_82575.c @@ -1818,27 +1818,32 @@ out: **/ void igb_vmdq_set_anti_spoofing_pf(struct e1000_hw *hw, bool enable, int pf) { - u32 dtxswc; + u32 reg_val, reg_offset; switch (hw->mac.type) { case e1000_82576: + reg_offset = E1000_DTXSWC; + break; case e1000_i350: - dtxswc = rd32(E1000_DTXSWC); - if (enable) { - dtxswc |= (E1000_DTXSWC_MAC_SPOOF_MASK | - E1000_DTXSWC_VLAN_SPOOF_MASK); - /* The PF can spoof - it has to in order to - * support emulation mode NICs */ - dtxswc ^= (1 << pf | 1 << (pf + MAX_NUM_VFS)); - } else { - dtxswc &= ~(E1000_DTXSWC_MAC_SPOOF_MASK | - E1000_DTXSWC_VLAN_SPOOF_MASK); - } - wr32(E1000_DTXSWC, dtxswc); + reg_offset = E1000_TXSWC; break; default: - break; + return; + } + + reg_val = rd32(reg_offset); + if (enable) { + reg_val |= (E1000_DTXSWC_MAC_SPOOF_MASK | + E1000_DTXSWC_VLAN_SPOOF_MASK); + /* The PF can spoof - it has to in order to + * support emulation mode NICs + */ + reg_val ^= (1 << pf | 1 << (pf + MAX_NUM_VFS)); + } else { + reg_val &= ~(E1000_DTXSWC_MAC_SPOOF_MASK | + E1000_DTXSWC_VLAN_SPOOF_MASK); } + wr32(reg_offset, reg_val); } /** -- cgit v1.2.3-58-ga151 From d0f63acc2ff354a525f7bc7ba90e81f49b6c2ef8 Mon Sep 17 00:00:00 2001 From: Alex Williamson Date: Wed, 13 Mar 2013 15:50:24 +0000 Subject: igb: Fix null pointer dereference The max_vfs= option has always been self limiting to the number of VFs supported by the device. fa44f2f1 added SR-IOV configuration via sysfs, but in the process broke this self correction factor. The failing path is: igb_probe igb_sw_init if (max_vfs > 7) { adapter->vfs_allocated_count = 7; ... igb_probe_vfs igb_enable_sriov(, max_vfs) if (num_vfs > 7) { err = -EPERM; ... This leaves vfs_allocated_count = 7 and vf_data = NULL, so we bomb out when igb_probe finally calls igb_reset. It seems like a really bad idea, and somewhat pointless, to set vfs_allocated_count separate from vf_data, but limiting max_vfs is enough to avoid the null pointer. Signed-off-by: Alex Williamson Acked-by: Greg Rose Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/igb/igb_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c index 4dbd62968c7a..2ae888678b23 100644 --- a/drivers/net/ethernet/intel/igb/igb_main.c +++ b/drivers/net/ethernet/intel/igb/igb_main.c @@ -2652,7 +2652,7 @@ static int igb_sw_init(struct igb_adapter *adapter) if (max_vfs > 7) { dev_warn(&pdev->dev, "Maximum of 7 VFs per PF, using max\n"); - adapter->vfs_allocated_count = 7; + max_vfs = adapter->vfs_allocated_count = 7; } else adapter->vfs_allocated_count = max_vfs; if (adapter->vfs_allocated_count) -- cgit v1.2.3-58-ga151 From d5e51a10d21761faaf069cac6f1c0311cf332820 Mon Sep 17 00:00:00 2001 From: Alex Williamson Date: Wed, 13 Mar 2013 15:50:29 +0000 Subject: igb: SR-IOV init reordering igb is ineffective at setting a lower total VFs because: int pci_sriov_set_totalvfs(struct pci_dev *dev, u16 numvfs) { ... /* Shouldn't change if VFs already enabled */ if (dev->sriov->ctrl & PCI_SRIOV_CTRL_VFE) return -EBUSY; Swap init ordering. Signed-off-by: Alex Williamson Acked-by: Greg Rose Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/igb/igb_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c index 2ae888678b23..8496adfc6a68 100644 --- a/drivers/net/ethernet/intel/igb/igb_main.c +++ b/drivers/net/ethernet/intel/igb/igb_main.c @@ -2542,8 +2542,8 @@ static void igb_probe_vfs(struct igb_adapter *adapter) if ((hw->mac.type == e1000_i210) || (hw->mac.type == e1000_i211)) return; - igb_enable_sriov(pdev, max_vfs); pci_sriov_set_totalvfs(pdev, 7); + igb_enable_sriov(pdev, max_vfs); #endif /* CONFIG_PCI_IOV */ } -- cgit v1.2.3-58-ga151 From 05ec29e8fa9b6ec8d4ad5d2f6d5fc5467c7970bc Mon Sep 17 00:00:00 2001 From: Stephen Hemminger Date: Wed, 20 Mar 2013 09:06:29 +0000 Subject: igb: make sensor info static Trivial sparse warning. Signed-off-by: Stephen Hemminger Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/igb/igb_hwmon.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/igb/igb_hwmon.c b/drivers/net/ethernet/intel/igb/igb_hwmon.c index 4623502054d5..0478a1abe541 100644 --- a/drivers/net/ethernet/intel/igb/igb_hwmon.c +++ b/drivers/net/ethernet/intel/igb/igb_hwmon.c @@ -39,7 +39,7 @@ #include #ifdef CONFIG_IGB_HWMON -struct i2c_board_info i350_sensor_info = { +static struct i2c_board_info i350_sensor_info = { I2C_BOARD_INFO("i350bb", (0Xf8 >> 1)), }; -- cgit v1.2.3-58-ga151 From 75517d92119a3cd364f618ee962055b3ded8c396 Mon Sep 17 00:00:00 2001 From: Jiri Benc Date: Wed, 20 Mar 2013 09:06:34 +0000 Subject: igb: fix PHC stopping on max freq For 82576 MAC type, max_adj is reported as 1000000000 ppb. However, if this value is passed to igb_ptp_adjfreq_82576, incvalue overflows out of INCVALUE_82576_MASK, resulting in setting of zero TIMINCA.incvalue, stopping the PHC (instead of going at twice the nominal speed). Fix the advertised max_adj value to the largest value hardware can handle. As there is no min_adj value available (-max_adj is used instead), this will also prevent stopping the clock intentionally. It's probably not a big deal, other igb MAC types don't support stopping the clock, either. Signed-off-by: Jiri Benc Acked-by: Matthew Vick Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/igb/igb_ptp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/igb/igb_ptp.c b/drivers/net/ethernet/intel/igb/igb_ptp.c index 0987822359f0..0a237507ee85 100644 --- a/drivers/net/ethernet/intel/igb/igb_ptp.c +++ b/drivers/net/ethernet/intel/igb/igb_ptp.c @@ -740,7 +740,7 @@ void igb_ptp_init(struct igb_adapter *adapter) case e1000_82576: snprintf(adapter->ptp_caps.name, 16, "%pm", netdev->dev_addr); adapter->ptp_caps.owner = THIS_MODULE; - adapter->ptp_caps.max_adj = 1000000000; + adapter->ptp_caps.max_adj = 999999881; adapter->ptp_caps.n_ext_ts = 0; adapter->ptp_caps.pps = 0; adapter->ptp_caps.adjfreq = igb_ptp_adjfreq_82576; -- cgit v1.2.3-58-ga151 From 76a0e68129d7d24eb995a6871ab47081bbfa0acc Mon Sep 17 00:00:00 2001 From: Veaceslav Falico Date: Mon, 25 Mar 2013 22:26:21 +0000 Subject: pch_gbe: fix ip_summed checksum reporting on rx skb->ip_summed should be CHECKSUM_UNNECESSARY when the driver reports that checksums were correct and CHECKSUM_NONE in any other case. They're currently placed vice versa, which breaks the forwarding scenario. Fix it by placing them as described above. Signed-off-by: Veaceslav Falico Signed-off-by: David S. Miller --- drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c index 39ab4d09faaa..73ce7dd6b954 100644 --- a/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c +++ b/drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c @@ -1726,9 +1726,9 @@ pch_gbe_clean_rx(struct pch_gbe_adapter *adapter, skb->protocol = eth_type_trans(skb, netdev); if (tcp_ip_status & PCH_GBE_RXD_ACC_STAT_TCPIPOK) - skb->ip_summed = CHECKSUM_NONE; - else skb->ip_summed = CHECKSUM_UNNECESSARY; + else + skb->ip_summed = CHECKSUM_NONE; napi_gro_receive(&adapter->napi, skb); (*work_done)++; -- cgit v1.2.3-58-ga151 From 9fe16b78ee17579cb4f333534cf7043e94c67024 Mon Sep 17 00:00:00 2001 From: Veaceslav Falico Date: Tue, 26 Mar 2013 17:43:28 +0100 Subject: bonding: remove already created master sysfs link on failure If slave sysfs symlink failes to be created - we end up without removing the master sysfs symlink. Remove it in case of failure. Signed-off-by: Veaceslav Falico Signed-off-by: David S. Miller --- drivers/net/bonding/bond_sysfs.c | 5 +++++ 1 file changed, 5 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_sysfs.c b/drivers/net/bonding/bond_sysfs.c index 1c9e09fbdff8..db103e03ba05 100644 --- a/drivers/net/bonding/bond_sysfs.c +++ b/drivers/net/bonding/bond_sysfs.c @@ -183,6 +183,11 @@ int bond_create_slave_symlinks(struct net_device *master, sprintf(linkname, "slave_%s", slave->name); ret = sysfs_create_link(&(master->dev.kobj), &(slave->dev.kobj), linkname); + + /* free the master link created earlier in case of error */ + if (ret) + sysfs_remove_link(&(slave->dev.kobj), "master"); + return ret; } -- cgit v1.2.3-58-ga151 From d6b057b5dbba97e6ba13aace5270babd7c8b658c Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:35 +0000 Subject: e1000: ethtool: Add missing dma_mapping_error-call in e1000_setup_desc_rings After dma_map_single, dma_mapping_error must be called. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000/e1000_ethtool.c | 14 +++++++++++--- 1 file changed, 11 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c index 43462d596a4e..ffd287196bf8 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_ethtool.c +++ b/drivers/net/ethernet/intel/e1000/e1000_ethtool.c @@ -1053,6 +1053,10 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) txdr->buffer_info[i].dma = dma_map_single(&pdev->dev, skb->data, skb->len, DMA_TO_DEVICE); + if (dma_mapping_error(&pdev->dev, txdr->buffer_info[i].dma)) { + ret_val = 4; + goto err_nomem; + } tx_desc->buffer_addr = cpu_to_le64(txdr->buffer_info[i].dma); tx_desc->lower.data = cpu_to_le32(skb->len); tx_desc->lower.data |= cpu_to_le32(E1000_TXD_CMD_EOP | @@ -1069,7 +1073,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->buffer_info = kcalloc(rxdr->count, sizeof(struct e1000_buffer), GFP_KERNEL); if (!rxdr->buffer_info) { - ret_val = 4; + ret_val = 5; goto err_nomem; } @@ -1077,7 +1081,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->desc = dma_alloc_coherent(&pdev->dev, rxdr->size, &rxdr->dma, GFP_KERNEL); if (!rxdr->desc) { - ret_val = 5; + ret_val = 6; goto err_nomem; } memset(rxdr->desc, 0, rxdr->size); @@ -1101,7 +1105,7 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) skb = alloc_skb(E1000_RXBUFFER_2048 + NET_IP_ALIGN, GFP_KERNEL); if (!skb) { - ret_val = 6; + ret_val = 7; goto err_nomem; } skb_reserve(skb, NET_IP_ALIGN); @@ -1110,6 +1114,10 @@ static int e1000_setup_desc_rings(struct e1000_adapter *adapter) rxdr->buffer_info[i].dma = dma_map_single(&pdev->dev, skb->data, E1000_RXBUFFER_2048, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, rxdr->buffer_info[i].dma)) { + ret_val = 8; + goto err_nomem; + } rx_desc->buffer_addr = cpu_to_le64(rxdr->buffer_info[i].dma); memset(skb->data, 0x00, skb->len); } -- cgit v1.2.3-58-ga151 From 065946c65a61943b4c609a0a1b1bac6742b3b593 Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:41 +0000 Subject: ixgb: Add missing dma_mapping_error-call in ixgb_alloc_rx_buffers After dma_map_single, dma_mapping_error must be called. It seems safe to not free the skb allocated in this function, as the skb can be reused later. Additionally this patch fixes one coding-style error. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgb/ixgb_main.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/ixgb/ixgb_main.c b/drivers/net/ethernet/intel/ixgb/ixgb_main.c index ea4808373435..b5f94abe3cff 100644 --- a/drivers/net/ethernet/intel/ixgb/ixgb_main.c +++ b/drivers/net/ethernet/intel/ixgb/ixgb_main.c @@ -2159,6 +2159,10 @@ map_skb: skb->data, adapter->rx_buffer_len, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { + adapter->alloc_rx_buff_failed++; + break; + } rx_desc = IXGB_RX_DESC(*rx_ring, i); rx_desc->buff_addr = cpu_to_le64(buffer_info->dma); @@ -2168,7 +2172,8 @@ map_skb: rx_desc->status = 0; - if (++i == rx_ring->count) i = 0; + if (++i == rx_ring->count) + i = 0; buffer_info = &rx_ring->buffer_info[i]; } -- cgit v1.2.3-58-ga151 From 37287fae7e4506fb0822523587c769783164cdd6 Mon Sep 17 00:00:00 2001 From: Christoph Paasch Date: Wed, 20 Mar 2013 08:59:46 +0000 Subject: e1000e: Add missing dma_mapping_error-call in e1000_alloc_jumbo_rx_buffers After dma_map_page, dma_mapping_error must be called. It seems safe to not free the skb/page allocated in this function, as the skb/page can be reused later. Signed-off-by: Christoph Paasch Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000e/netdev.c | 7 ++++++- 1 file changed, 6 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index 948b86ffa4f0..7e615e2bf7e6 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -848,11 +848,16 @@ check_page: } } - if (!buffer_info->dma) + if (!buffer_info->dma) { buffer_info->dma = dma_map_page(&pdev->dev, buffer_info->page, 0, PAGE_SIZE, DMA_FROM_DEVICE); + if (dma_mapping_error(&pdev->dev, buffer_info->dma)) { + adapter->alloc_rx_buff_failed++; + break; + } + } rx_desc = E1000_RX_DESC_EXT(*rx_ring, i); rx_desc->read.buffer_addr = cpu_to_le64(buffer_info->dma); -- cgit v1.2.3-58-ga151 From f901b6bc404b67d96eca739857c097e022727b71 Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Wed, 27 Mar 2013 11:36:42 +0100 Subject: can: sja1000: fix define conflict on SH Thias patch fixes a define conflict between the SH architecture and the sja1000 driver: drivers/net/can/sja1000/sja1000.h:59:0: warning: "REG_SR" redefined [enabled by default] arch/sh/include/asm/ptrace_32.h:25:0: note: this is the location of the previous definition A SJA1000_ prefix is added to the offending sja1000 define only, to make a minimal patch suited for stable. A later patch will add a SJA1000_ prefix to all defines in sja1000.h. Cc: linux-stable Reported-by: Fengguang Wu Signed-off-by: Marc Kleine-Budde --- drivers/net/can/sja1000/plx_pci.c | 4 ++-- drivers/net/can/sja1000/sja1000.c | 6 +++--- drivers/net/can/sja1000/sja1000.h | 2 +- 3 files changed, 6 insertions(+), 6 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/can/sja1000/plx_pci.c b/drivers/net/can/sja1000/plx_pci.c index a042cdc260dc..3c18d7d000ed 100644 --- a/drivers/net/can/sja1000/plx_pci.c +++ b/drivers/net/can/sja1000/plx_pci.c @@ -348,7 +348,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv) */ if ((priv->read_reg(priv, REG_CR) & REG_CR_BASICCAN_INITIAL_MASK) == REG_CR_BASICCAN_INITIAL && - (priv->read_reg(priv, REG_SR) == REG_SR_BASICCAN_INITIAL) && + (priv->read_reg(priv, SJA1000_REG_SR) == REG_SR_BASICCAN_INITIAL) && (priv->read_reg(priv, REG_IR) == REG_IR_BASICCAN_INITIAL)) flag = 1; @@ -360,7 +360,7 @@ static inline int plx_pci_check_sja1000(const struct sja1000_priv *priv) * See states on p. 23 of the Datasheet. */ if (priv->read_reg(priv, REG_MOD) == REG_MOD_PELICAN_INITIAL && - priv->read_reg(priv, REG_SR) == REG_SR_PELICAN_INITIAL && + priv->read_reg(priv, SJA1000_REG_SR) == REG_SR_PELICAN_INITIAL && priv->read_reg(priv, REG_IR) == REG_IR_PELICAN_INITIAL) return flag; diff --git a/drivers/net/can/sja1000/sja1000.c b/drivers/net/can/sja1000/sja1000.c index daf4013a8fc7..e4df307eaa90 100644 --- a/drivers/net/can/sja1000/sja1000.c +++ b/drivers/net/can/sja1000/sja1000.c @@ -92,7 +92,7 @@ static void sja1000_write_cmdreg(struct sja1000_priv *priv, u8 val) */ spin_lock_irqsave(&priv->cmdreg_lock, flags); priv->write_reg(priv, REG_CMR, val); - priv->read_reg(priv, REG_SR); + priv->read_reg(priv, SJA1000_REG_SR); spin_unlock_irqrestore(&priv->cmdreg_lock, flags); } @@ -502,7 +502,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) while ((isrc = priv->read_reg(priv, REG_IR)) && (n < SJA1000_MAX_IRQ)) { n++; - status = priv->read_reg(priv, REG_SR); + status = priv->read_reg(priv, SJA1000_REG_SR); /* check for absent controller due to hw unplug */ if (status == 0xFF && sja1000_is_absent(priv)) return IRQ_NONE; @@ -530,7 +530,7 @@ irqreturn_t sja1000_interrupt(int irq, void *dev_id) /* receive interrupt */ while (status & SR_RBS) { sja1000_rx(dev); - status = priv->read_reg(priv, REG_SR); + status = priv->read_reg(priv, SJA1000_REG_SR); /* check for absent controller */ if (status == 0xFF && sja1000_is_absent(priv)) return IRQ_NONE; diff --git a/drivers/net/can/sja1000/sja1000.h b/drivers/net/can/sja1000/sja1000.h index afa99847a510..aa48e053da27 100644 --- a/drivers/net/can/sja1000/sja1000.h +++ b/drivers/net/can/sja1000/sja1000.h @@ -56,7 +56,7 @@ /* SJA1000 registers - manual section 6.4 (Pelican Mode) */ #define REG_MOD 0x00 #define REG_CMR 0x01 -#define REG_SR 0x02 +#define SJA1000_REG_SR 0x02 #define REG_IR 0x03 #define REG_IER 0x04 #define REG_ALC 0x0B -- cgit v1.2.3-58-ga151 From 3fd33497f80aa528ded0db2851b48638635d5caa Mon Sep 17 00:00:00 2001 From: Marc Kleine-Budde Date: Wed, 27 Mar 2013 12:47:13 +0100 Subject: can: sja1000: limit PEAK PCAN-PC Card to HAS_IOPORT This patch limits the PEAK PCAN-PC Card driver to systems with ioports. Fixes a compile time breakage on SH: drivers/net/can/sja1000/peak_pcmcia.c:626:2: error: implicit declaration of function 'ioport_unmap' Reported-by: Fengguang Wu Cc: Paul Mundt Signed-off-by: Marc Kleine-Budde --- drivers/net/can/sja1000/Kconfig | 1 + 1 file changed, 1 insertion(+) (limited to 'drivers/net') diff --git a/drivers/net/can/sja1000/Kconfig b/drivers/net/can/sja1000/Kconfig index b39ca5b3ea7f..ff2ba86cd4a4 100644 --- a/drivers/net/can/sja1000/Kconfig +++ b/drivers/net/can/sja1000/Kconfig @@ -46,6 +46,7 @@ config CAN_EMS_PCI config CAN_PEAK_PCMCIA tristate "PEAK PCAN-PC Card" depends on PCMCIA + depends on HAS_IOPORT ---help--- This driver is for the PCAN-PC Card PCMCIA adapter (1 or 2 channels) from PEAK-System (http://www.peak-system.com). To compile this -- cgit v1.2.3-58-ga151 From 54683441a92ebe20c5282465ea6f21e5e74d2974 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Wed, 27 Mar 2013 10:52:11 -0400 Subject: Revert "brcmsmac: support 4313iPA" This reverts commit b6fc28a158076ca2764edc9a6d1e1402f56e1c0c. This commit is reported to cause a regression in the support for some revisions of 4313 ePA devices. http://marc.info/?l=linux-wireless&m=136360340200943&w=2 Conflicts: drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c Reported-by: David Herrmann Signed-off-by: John W. Linville --- .../net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c | 369 ++++++++------------- .../wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c | 64 ++-- 2 files changed, 162 insertions(+), 271 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c index 21a824232478..18d37645e2cd 100644 --- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c +++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phy_lcn.c @@ -1137,9 +1137,8 @@ wlc_lcnphy_set_rx_gain_by_distribution(struct brcms_phy *pi, gain0_15 = ((biq1 & 0xf) << 12) | ((tia & 0xf) << 8) | ((lna2 & 0x3) << 6) | - ((lna2 & 0x3) << 4) | - ((lna1 & 0x3) << 2) | - ((lna1 & 0x3) << 0); + ((lna2 & + 0x3) << 4) | ((lna1 & 0x3) << 2) | ((lna1 & 0x3) << 0); mod_phy_reg(pi, 0x4b6, (0xffff << 0), gain0_15 << 0); mod_phy_reg(pi, 0x4b7, (0xf << 0), gain16_19 << 0); @@ -1157,8 +1156,6 @@ wlc_lcnphy_set_rx_gain_by_distribution(struct brcms_phy *pi, } mod_phy_reg(pi, 0x44d, (0x1 << 0), (!trsw) << 0); - mod_phy_reg(pi, 0x4b1, (0x3 << 11), lna1 << 11); - mod_phy_reg(pi, 0x4e6, (0x3 << 3), lna1 << 3); } @@ -1331,43 +1328,6 @@ static u32 wlc_lcnphy_measure_digital_power(struct brcms_phy *pi, u16 nsamples) return (iq_est.i_pwr + iq_est.q_pwr) / nsamples; } -static bool wlc_lcnphy_rx_iq_cal_gain(struct brcms_phy *pi, u16 biq1_gain, - u16 tia_gain, u16 lna2_gain) -{ - u32 i_thresh_l, q_thresh_l; - u32 i_thresh_h, q_thresh_h; - struct lcnphy_iq_est iq_est_h, iq_est_l; - - wlc_lcnphy_set_rx_gain_by_distribution(pi, 0, 0, 0, biq1_gain, tia_gain, - lna2_gain, 0); - - wlc_lcnphy_rx_gain_override_enable(pi, true); - wlc_lcnphy_start_tx_tone(pi, 2000, (40 >> 1), 0); - udelay(500); - write_radio_reg(pi, RADIO_2064_REG112, 0); - if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_l)) - return false; - - wlc_lcnphy_start_tx_tone(pi, 2000, 40, 0); - udelay(500); - write_radio_reg(pi, RADIO_2064_REG112, 0); - if (!wlc_lcnphy_rx_iq_est(pi, 1024, 32, &iq_est_h)) - return false; - - i_thresh_l = (iq_est_l.i_pwr << 1); - i_thresh_h = (iq_est_l.i_pwr << 2) + iq_est_l.i_pwr; - - q_thresh_l = (iq_est_l.q_pwr << 1); - q_thresh_h = (iq_est_l.q_pwr << 2) + iq_est_l.q_pwr; - if ((iq_est_h.i_pwr > i_thresh_l) && - (iq_est_h.i_pwr < i_thresh_h) && - (iq_est_h.q_pwr > q_thresh_l) && - (iq_est_h.q_pwr < q_thresh_h)) - return true; - - return false; -} - static bool wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, const struct lcnphy_rx_iqcomp *iqcomp, @@ -1382,8 +1342,8 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, RFOverrideVal0_old, rfoverride2_old, rfoverride2val_old, rfoverride3_old, rfoverride3val_old, rfoverride4_old, rfoverride4val_old, afectrlovr_old, afectrlovrval_old; - int tia_gain, lna2_gain, biq1_gain; - bool set_gain; + int tia_gain; + u32 received_power, rx_pwr_threshold; u16 old_sslpnCalibClkEnCtrl, old_sslpnRxFeClkEnCtrl; u16 values_to_save[11]; s16 *ptr; @@ -1408,134 +1368,126 @@ wlc_lcnphy_rx_iq_cal(struct brcms_phy *pi, goto cal_done; } - WARN_ON(module != 1); - tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi); - wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF); - - for (i = 0; i < 11; i++) - values_to_save[i] = - read_radio_reg(pi, rxiq_cal_rf_reg[i]); - Core1TxControl_old = read_phy_reg(pi, 0x631); - - or_phy_reg(pi, 0x631, 0x0015); - - RFOverride0_old = read_phy_reg(pi, 0x44c); - RFOverrideVal0_old = read_phy_reg(pi, 0x44d); - rfoverride2_old = read_phy_reg(pi, 0x4b0); - rfoverride2val_old = read_phy_reg(pi, 0x4b1); - rfoverride3_old = read_phy_reg(pi, 0x4f9); - rfoverride3val_old = read_phy_reg(pi, 0x4fa); - rfoverride4_old = read_phy_reg(pi, 0x938); - rfoverride4val_old = read_phy_reg(pi, 0x939); - afectrlovr_old = read_phy_reg(pi, 0x43b); - afectrlovrval_old = read_phy_reg(pi, 0x43c); - old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da); - old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db); - - tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi); - if (tx_gain_override_old) { - wlc_lcnphy_get_tx_gain(pi, &old_gains); - tx_gain_index_old = pi_lcn->lcnphy_current_index; - } - - wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx); + if (module == 1) { - mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0); + tx_pwr_ctrl = wlc_lcnphy_get_tx_pwr_ctrl(pi); + wlc_lcnphy_set_tx_pwr_ctrl(pi, LCNPHY_TX_PWR_CTRL_OFF); - mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1); + for (i = 0; i < 11; i++) + values_to_save[i] = + read_radio_reg(pi, rxiq_cal_rf_reg[i]); + Core1TxControl_old = read_phy_reg(pi, 0x631); + + or_phy_reg(pi, 0x631, 0x0015); + + RFOverride0_old = read_phy_reg(pi, 0x44c); + RFOverrideVal0_old = read_phy_reg(pi, 0x44d); + rfoverride2_old = read_phy_reg(pi, 0x4b0); + rfoverride2val_old = read_phy_reg(pi, 0x4b1); + rfoverride3_old = read_phy_reg(pi, 0x4f9); + rfoverride3val_old = read_phy_reg(pi, 0x4fa); + rfoverride4_old = read_phy_reg(pi, 0x938); + rfoverride4val_old = read_phy_reg(pi, 0x939); + afectrlovr_old = read_phy_reg(pi, 0x43b); + afectrlovrval_old = read_phy_reg(pi, 0x43c); + old_sslpnCalibClkEnCtrl = read_phy_reg(pi, 0x6da); + old_sslpnRxFeClkEnCtrl = read_phy_reg(pi, 0x6db); + + tx_gain_override_old = wlc_lcnphy_tx_gain_override_enabled(pi); + if (tx_gain_override_old) { + wlc_lcnphy_get_tx_gain(pi, &old_gains); + tx_gain_index_old = pi_lcn->lcnphy_current_index; + } - write_radio_reg(pi, RADIO_2064_REG116, 0x06); - write_radio_reg(pi, RADIO_2064_REG12C, 0x07); - write_radio_reg(pi, RADIO_2064_REG06A, 0xd3); - write_radio_reg(pi, RADIO_2064_REG098, 0x03); - write_radio_reg(pi, RADIO_2064_REG00B, 0x7); - mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4); - write_radio_reg(pi, RADIO_2064_REG01D, 0x01); - write_radio_reg(pi, RADIO_2064_REG114, 0x01); - write_radio_reg(pi, RADIO_2064_REG02E, 0x10); - write_radio_reg(pi, RADIO_2064_REG12A, 0x08); - - mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0); - mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1); - mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2); - mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2); - mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3); - mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3); - mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5); - mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5); + wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_idx); - mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0); - mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0); + mod_phy_reg(pi, 0x4f9, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x4fa, (0x1 << 0), 0 << 0); - write_phy_reg(pi, 0x6da, 0xffff); - or_phy_reg(pi, 0x6db, 0x3); + mod_phy_reg(pi, 0x43b, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x43c, (0x1 << 1), 0 << 1); - wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch); - set_gain = false; - - lna2_gain = 3; - while ((lna2_gain >= 0) && !set_gain) { - tia_gain = 4; - - while ((tia_gain >= 0) && !set_gain) { - biq1_gain = 6; - - while ((biq1_gain >= 0) && !set_gain) { - set_gain = wlc_lcnphy_rx_iq_cal_gain(pi, - (u16) - biq1_gain, - (u16) - tia_gain, - (u16) - lna2_gain); - biq1_gain -= 1; - } + write_radio_reg(pi, RADIO_2064_REG116, 0x06); + write_radio_reg(pi, RADIO_2064_REG12C, 0x07); + write_radio_reg(pi, RADIO_2064_REG06A, 0xd3); + write_radio_reg(pi, RADIO_2064_REG098, 0x03); + write_radio_reg(pi, RADIO_2064_REG00B, 0x7); + mod_radio_reg(pi, RADIO_2064_REG113, 1 << 4, 1 << 4); + write_radio_reg(pi, RADIO_2064_REG01D, 0x01); + write_radio_reg(pi, RADIO_2064_REG114, 0x01); + write_radio_reg(pi, RADIO_2064_REG02E, 0x10); + write_radio_reg(pi, RADIO_2064_REG12A, 0x08); + + mod_phy_reg(pi, 0x938, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x939, (0x1 << 0), 0 << 0); + mod_phy_reg(pi, 0x938, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x939, (0x1 << 1), 1 << 1); + mod_phy_reg(pi, 0x938, (0x1 << 2), 1 << 2); + mod_phy_reg(pi, 0x939, (0x1 << 2), 1 << 2); + mod_phy_reg(pi, 0x938, (0x1 << 3), 1 << 3); + mod_phy_reg(pi, 0x939, (0x1 << 3), 1 << 3); + mod_phy_reg(pi, 0x938, (0x1 << 5), 1 << 5); + mod_phy_reg(pi, 0x939, (0x1 << 5), 0 << 5); + + mod_phy_reg(pi, 0x43b, (0x1 << 0), 1 << 0); + mod_phy_reg(pi, 0x43c, (0x1 << 0), 0 << 0); + + wlc_lcnphy_start_tx_tone(pi, 2000, 120, 0); + write_phy_reg(pi, 0x6da, 0xffff); + or_phy_reg(pi, 0x6db, 0x3); + wlc_lcnphy_set_trsw_override(pi, tx_switch, rx_switch); + wlc_lcnphy_rx_gain_override_enable(pi, true); + + tia_gain = 8; + rx_pwr_threshold = 950; + while (tia_gain > 0) { tia_gain -= 1; + wlc_lcnphy_set_rx_gain_by_distribution(pi, + 0, 0, 2, 2, + (u16) + tia_gain, 1, 0); + udelay(500); + + received_power = + wlc_lcnphy_measure_digital_power(pi, 2000); + if (received_power < rx_pwr_threshold) + break; } - lna2_gain -= 1; - } + result = wlc_lcnphy_calc_rx_iq_comp(pi, 0xffff); - if (set_gain) - result = wlc_lcnphy_calc_rx_iq_comp(pi, 1024); - else - result = false; + wlc_lcnphy_stop_tx_tone(pi); - wlc_lcnphy_stop_tx_tone(pi); + write_phy_reg(pi, 0x631, Core1TxControl_old); - write_phy_reg(pi, 0x631, Core1TxControl_old); - - write_phy_reg(pi, 0x44c, RFOverrideVal0_old); - write_phy_reg(pi, 0x44d, RFOverrideVal0_old); - write_phy_reg(pi, 0x4b0, rfoverride2_old); - write_phy_reg(pi, 0x4b1, rfoverride2val_old); - write_phy_reg(pi, 0x4f9, rfoverride3_old); - write_phy_reg(pi, 0x4fa, rfoverride3val_old); - write_phy_reg(pi, 0x938, rfoverride4_old); - write_phy_reg(pi, 0x939, rfoverride4val_old); - write_phy_reg(pi, 0x43b, afectrlovr_old); - write_phy_reg(pi, 0x43c, afectrlovrval_old); - write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl); - write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl); + write_phy_reg(pi, 0x44c, RFOverrideVal0_old); + write_phy_reg(pi, 0x44d, RFOverrideVal0_old); + write_phy_reg(pi, 0x4b0, rfoverride2_old); + write_phy_reg(pi, 0x4b1, rfoverride2val_old); + write_phy_reg(pi, 0x4f9, rfoverride3_old); + write_phy_reg(pi, 0x4fa, rfoverride3val_old); + write_phy_reg(pi, 0x938, rfoverride4_old); + write_phy_reg(pi, 0x939, rfoverride4val_old); + write_phy_reg(pi, 0x43b, afectrlovr_old); + write_phy_reg(pi, 0x43c, afectrlovrval_old); + write_phy_reg(pi, 0x6da, old_sslpnCalibClkEnCtrl); + write_phy_reg(pi, 0x6db, old_sslpnRxFeClkEnCtrl); - wlc_lcnphy_clear_trsw_override(pi); + wlc_lcnphy_clear_trsw_override(pi); - mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2); + mod_phy_reg(pi, 0x44c, (0x1 << 2), 0 << 2); - for (i = 0; i < 11; i++) - write_radio_reg(pi, rxiq_cal_rf_reg[i], - values_to_save[i]); + for (i = 0; i < 11; i++) + write_radio_reg(pi, rxiq_cal_rf_reg[i], + values_to_save[i]); - if (tx_gain_override_old) - wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old); - else - wlc_lcnphy_disable_tx_gain_override(pi); + if (tx_gain_override_old) + wlc_lcnphy_set_tx_pwr_by_index(pi, tx_gain_index_old); + else + wlc_lcnphy_disable_tx_gain_override(pi); - wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl); - wlc_lcnphy_rx_gain_override_enable(pi, false); + wlc_lcnphy_set_tx_pwr_ctrl(pi, tx_pwr_ctrl); + wlc_lcnphy_rx_gain_override_enable(pi, false); + } cal_done: kfree(ptr); @@ -1829,17 +1781,6 @@ wlc_lcnphy_radio_2064_channel_tune_4313(struct brcms_phy *pi, u8 channel) write_radio_reg(pi, RADIO_2064_REG038, 3); write_radio_reg(pi, RADIO_2064_REG091, 7); } - - if (!(pi->sh->boardflags & BFL_FEM)) { - u8 reg038[14] = {0xd, 0xe, 0xd, 0xd, 0xd, 0xc, - 0xa, 0xb, 0xb, 0x3, 0x3, 0x2, 0x0, 0x0}; - - write_radio_reg(pi, RADIO_2064_REG02A, 0xf); - write_radio_reg(pi, RADIO_2064_REG091, 0x3); - write_radio_reg(pi, RADIO_2064_REG038, 0x3); - - write_radio_reg(pi, RADIO_2064_REG038, reg038[channel - 1]); - } } static int @@ -2034,16 +1975,6 @@ wlc_lcnphy_set_tssi_mux(struct brcms_phy *pi, enum lcnphy_tssi_mode pos) } else { mod_radio_reg(pi, RADIO_2064_REG03A, 1, 0x1); mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8); - mod_radio_reg(pi, RADIO_2064_REG028, 0x1, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x4, 1<<2); - mod_radio_reg(pi, RADIO_2064_REG036, 0x10, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x10, 1<<4); - mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0); - mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x77); - mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, 0xe<<1); - mod_radio_reg(pi, RADIO_2064_REG112, 0x80, 1<<7); - mod_radio_reg(pi, RADIO_2064_REG005, 0x7, 1<<1); - mod_radio_reg(pi, RADIO_2064_REG029, 0xf0, 0<<4); } } else { mod_phy_reg(pi, 0x4d9, (0x1 << 2), (0x1) << 2); @@ -2130,14 +2061,12 @@ static void wlc_lcnphy_pwrctrl_rssiparams(struct brcms_phy *pi) (auxpga_vmid_temp << 0) | (auxpga_gain_temp << 12)); mod_radio_reg(pi, RADIO_2064_REG082, (1 << 5), (1 << 5)); - mod_radio_reg(pi, RADIO_2064_REG07C, (1 << 0), (1 << 0)); } static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) { struct phytbl_info tab; u32 rfseq, ind; - u8 tssi_sel; tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL; tab.tbl_width = 32; @@ -2159,13 +2088,7 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x503, (0x1 << 4), (1) << 4); - if (pi->sh->boardflags & BFL_FEM) { - tssi_sel = 0x1; - wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_EXT); - } else { - tssi_sel = 0xe; - wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_POST_PA); - } + wlc_lcnphy_set_tssi_mux(pi, LCNPHY_TSSI_EXT); mod_phy_reg(pi, 0x4a4, (0x1 << 14), (0) << 14); mod_phy_reg(pi, 0x4a4, (0x1 << 15), (1) << 15); @@ -2201,10 +2124,9 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x49a, (0x1ff << 0), (0xff) << 0); if (LCNREV_IS(pi->pubpi.phy_rev, 2)) { - mod_radio_reg(pi, RADIO_2064_REG028, 0xf, tssi_sel); + mod_radio_reg(pi, RADIO_2064_REG028, 0xf, 0xe); mod_radio_reg(pi, RADIO_2064_REG086, 0x4, 0x4); } else { - mod_radio_reg(pi, RADIO_2064_REG028, 0x1e, tssi_sel << 1); mod_radio_reg(pi, RADIO_2064_REG03A, 0x1, 1); mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 1 << 3); } @@ -2251,10 +2173,6 @@ static void wlc_lcnphy_tssi_setup(struct brcms_phy *pi) mod_phy_reg(pi, 0x4d7, (0xf << 8), (0) << 8); - mod_radio_reg(pi, RADIO_2064_REG035, 0xff, 0x0); - mod_radio_reg(pi, RADIO_2064_REG036, 0x3, 0x0); - mod_radio_reg(pi, RADIO_2064_REG11A, 0x8, 0x8); - wlc_lcnphy_pwrctrl_rssiparams(pi); } @@ -2873,8 +2791,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) read_radio_reg(pi, RADIO_2064_REG007) & 1; u16 SAVE_jtag_auxpga = read_radio_reg(pi, RADIO_2064_REG0FF) & 0x10; u16 SAVE_iqadc_aux_en = read_radio_reg(pi, RADIO_2064_REG11F) & 4; - u8 SAVE_bbmult = wlc_lcnphy_get_bbmult(pi); - idleTssi = read_phy_reg(pi, 0x4ab); suspend = (0 == (bcma_read32(pi->d11core, D11REGOFFS(maccontrol)) & MCTL_EN_MAC)); @@ -2892,12 +2808,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) mod_radio_reg(pi, RADIO_2064_REG0FF, 0x10, 1 << 4); mod_radio_reg(pi, RADIO_2064_REG11F, 0x4, 1 << 2); wlc_lcnphy_tssi_setup(pi); - - mod_phy_reg(pi, 0x4d7, (0x1 << 0), (1 << 0)); - mod_phy_reg(pi, 0x4d7, (0x1 << 6), (1 << 6)); - - wlc_lcnphy_set_bbmult(pi, 0x0); - wlc_phy_do_dummy_tx(pi, true, OFF); idleTssi = ((read_phy_reg(pi, 0x4ab) & (0x1ff << 0)) >> 0); @@ -2919,7 +2829,6 @@ static void wlc_lcnphy_idle_tssi_est(struct brcms_phy_pub *ppi) mod_phy_reg(pi, 0x44c, (0x1 << 12), (0) << 12); - wlc_lcnphy_set_bbmult(pi, SAVE_bbmult); wlc_lcnphy_set_tx_gain_override(pi, tx_gain_override_old); wlc_lcnphy_set_tx_gain(pi, &old_gains); wlc_lcnphy_set_tx_pwr_ctrl(pi, SAVE_txpwrctrl); @@ -3133,11 +3042,6 @@ static void wlc_lcnphy_tx_pwr_ctrl_init(struct brcms_phy_pub *ppi) wlc_lcnphy_write_table(pi, &tab); tab.tbl_offset++; } - mod_phy_reg(pi, 0x4d0, (0x1 << 0), (0) << 0); - mod_phy_reg(pi, 0x4d3, (0xff << 0), (0) << 0); - mod_phy_reg(pi, 0x4d3, (0xff << 8), (0) << 8); - mod_phy_reg(pi, 0x4d0, (0x1 << 4), (0) << 4); - mod_phy_reg(pi, 0x4d0, (0x1 << 2), (0) << 2); mod_phy_reg(pi, 0x410, (0x1 << 7), (0) << 7); @@ -3939,6 +3843,7 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi) target_gains.pad_gain = 21; target_gains.dac_gain = 0; wlc_lcnphy_set_tx_gain(pi, &target_gains); + wlc_lcnphy_set_tx_pwr_by_index(pi, 16); if (LCNREV_IS(pi->pubpi.phy_rev, 1) || pi_lcn->lcnphy_hw_iqcal_en) { @@ -3949,7 +3854,6 @@ static void wlc_lcnphy_txpwrtbl_iqlo_cal(struct brcms_phy *pi) lcnphy_recal ? LCNPHY_CAL_RECAL : LCNPHY_CAL_FULL), false); } else { - wlc_lcnphy_set_tx_pwr_by_index(pi, 16); wlc_lcnphy_tx_iqlo_soft_cal_full(pi); } @@ -4374,22 +4278,17 @@ wlc_lcnphy_load_tx_gain_table(struct brcms_phy *pi, if (CHSPEC_IS5G(pi->radio_chanspec)) pa_gain = 0x70; else - pa_gain = 0x60; + pa_gain = 0x70; if (pi->sh->boardflags & BFL_FEM) pa_gain = 0x10; - tab.tbl_id = LCNPHY_TBL_ID_TXPWRCTL; tab.tbl_width = 32; tab.tbl_len = 1; tab.tbl_ptr = &val; for (j = 0; j < 128; j++) { - if (pi->sh->boardflags & BFL_FEM) - gm_gain = gain_table[j].gm; - else - gm_gain = 15; - + gm_gain = gain_table[j].gm; val = (((u32) pa_gain << 24) | (gain_table[j].pad << 16) | (gain_table[j].pga << 8) | gm_gain); @@ -4600,10 +4499,7 @@ static void wlc_radio_2064_init(struct brcms_phy *pi) write_phy_reg(pi, 0x4ea, 0x4688); - if (pi->sh->boardflags & BFL_FEM) - mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0); - else - mod_phy_reg(pi, 0x4eb, (0x7 << 0), 3 << 0); + mod_phy_reg(pi, 0x4eb, (0x7 << 0), 2 << 0); mod_phy_reg(pi, 0x4eb, (0x7 << 6), 0 << 6); @@ -4614,13 +4510,6 @@ static void wlc_radio_2064_init(struct brcms_phy *pi) wlc_lcnphy_rcal(pi); wlc_lcnphy_rc_cal(pi); - - if (!(pi->sh->boardflags & BFL_FEM)) { - write_radio_reg(pi, RADIO_2064_REG032, 0x6f); - write_radio_reg(pi, RADIO_2064_REG033, 0x19); - write_radio_reg(pi, RADIO_2064_REG039, 0xe); - } - } static void wlc_lcnphy_radio_init(struct brcms_phy *pi) @@ -4650,20 +4539,22 @@ static void wlc_lcnphy_tbl_init(struct brcms_phy *pi) wlc_lcnphy_write_table(pi, &tab); } - if (!(pi->sh->boardflags & BFL_FEM)) { - tab.tbl_id = LCNPHY_TBL_ID_RFSEQ; - tab.tbl_width = 16; - tab.tbl_ptr = &val; - tab.tbl_len = 1; + tab.tbl_id = LCNPHY_TBL_ID_RFSEQ; + tab.tbl_width = 16; + tab.tbl_ptr = &val; + tab.tbl_len = 1; - val = 150; - tab.tbl_offset = 0; - wlc_lcnphy_write_table(pi, &tab); + val = 114; + tab.tbl_offset = 0; + wlc_lcnphy_write_table(pi, &tab); - val = 220; - tab.tbl_offset = 1; - wlc_lcnphy_write_table(pi, &tab); - } + val = 130; + tab.tbl_offset = 1; + wlc_lcnphy_write_table(pi, &tab); + + val = 6; + tab.tbl_offset = 8; + wlc_lcnphy_write_table(pi, &tab); if (CHSPEC_IS2G(pi->radio_chanspec)) { if (pi->sh->boardflags & BFL_FEM) @@ -5055,7 +4946,6 @@ void wlc_phy_chanspec_set_lcnphy(struct brcms_phy *pi, u16 chanspec) wlc_lcnphy_load_tx_iir_filter(pi, true, 3); mod_phy_reg(pi, 0x4eb, (0x7 << 3), (1) << 3); - wlc_lcnphy_tssi_setup(pi); } void wlc_phy_detach_lcnphy(struct brcms_phy *pi) @@ -5094,7 +4984,8 @@ bool wlc_phy_attach_lcnphy(struct brcms_phy *pi) if (!wlc_phy_txpwr_srom_read_lcnphy(pi)) return false; - if (LCNREV_IS(pi->pubpi.phy_rev, 1)) { + if ((pi->sh->boardflags & BFL_FEM) && + (LCNREV_IS(pi->pubpi.phy_rev, 1))) { if (pi_lcn->lcnphy_tempsense_option == 3) { pi->hwpwrctrl = true; pi->hwpwrctrl_capable = true; diff --git a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c index b7e95acc2084..622c01ca72c5 100644 --- a/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c +++ b/drivers/net/wireless/brcm80211/brcmsmac/phy/phytbl_lcn.c @@ -1992,70 +1992,70 @@ static const u16 dot11lcn_sw_ctrl_tbl_4313_epa_rev0[] = { }; static const u16 dot11lcn_sw_ctrl_tbl_4313_rev0[] = { - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, - 0x0009, 0x000a, - 0x0005, - 0x0006, 0x0009, - 0x000a, - 0x0005, 0x0006, - 0x0009, - 0x000a, 0x0005, - 0x0006, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, + 0x000a, 0x0009, + 0x0006, + 0x0005, 0x000a, + 0x0009, + 0x0006, 0x0005, + 0x000a, + 0x0009, 0x0006, + 0x0005, }; static const u16 dot11lcn_sw_ctrl_tbl_rev0[] = { -- cgit v1.2.3-58-ga151 From e67dd874e60529dbd2e8232babb1e23479ba2ffa Mon Sep 17 00:00:00 2001 From: Rafał Miłecki Date: Tue, 19 Mar 2013 07:52:48 +0100 Subject: b43: N-PHY: increase initial value of "mind" in RSSI calibration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit We're using "mind" variable to find the VCM that got the best polling results. For each VCM we calculte "currd" which is compared to the "mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a value smaller than 40 makes no sense, so increase the initial value. This fixes a regression introduced in 3.4 by commit: e0c9a0219a8f542e3946fe972a68aacf8c3f906c (my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s) Signed-off-by: Rafał Miłecki Cc: stable@vger.kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/b43/phy_n.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c index 3c35382ee6c2..e014a7a8154d 100644 --- a/drivers/net/wireless/b43/phy_n.c +++ b/drivers/net/wireless/b43/phy_n.c @@ -1615,7 +1615,7 @@ static void b43_nphy_rev3_rssi_cal(struct b43_wldev *dev) } for (i = 0; i < 4; i += 2) { s32 curr; - s32 mind = 40; + s32 mind = 0x100000; s32 minpoll = 249; u8 minvcm = 0; if (2 * core != i) @@ -1799,7 +1799,7 @@ static void b43_nphy_rev2_rssi_cal(struct b43_wldev *dev, u8 type) } for (i = 0; i < 4; i++) { - s32 mind = 40; + s32 mind = 0x100000; u8 minvcm = 0; s32 minpoll = 249; s32 curr; -- cgit v1.2.3-58-ga151 From b251412db99ccd4495ce372fec7daee27bf06923 Mon Sep 17 00:00:00 2001 From: "Iestyn C. Elfick" Date: Wed, 20 Mar 2013 14:02:31 -0500 Subject: b43: A fix for DMA transmission sequence errors Intermittently, b43 will report "Out of order TX status report on DMA ring". When this happens, the driver must be reset before communication can resume. The cause of the problem is believed to be an error in the closed-source firmware; however, all versions of the firmware are affected. This change uses the observation that the expected status is always 2 less than the observed value, and supplies a fake status report to skip one header/data pair. Not all devices suffer from this problem, but it can occur several times per second under heavy load. As each occurence kills the unmodified driver, this patch makes if possible for the affected devices to function. The patch logs only the first instance of the reset operation to prevent spamming the logs. Tested-by: Chris Vine Signed-off-by: Larry Finger Cc: Stable Signed-off-by: John W. Linville --- drivers/net/wireless/b43/dma.c | 65 ++++++++++++++++++++++++++++++++++-------- 1 file changed, 53 insertions(+), 12 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/dma.c b/drivers/net/wireless/b43/dma.c index 38bc5a7997ff..122146943bf2 100644 --- a/drivers/net/wireless/b43/dma.c +++ b/drivers/net/wireless/b43/dma.c @@ -1487,8 +1487,12 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, const struct b43_dma_ops *ops; struct b43_dmaring *ring; struct b43_dmadesc_meta *meta; + static const struct b43_txstatus fake; /* filled with 0 */ + const struct b43_txstatus *txstat; int slot, firstused; bool frame_succeed; + int skip; + static u8 err_out1, err_out2; ring = parse_cookie(dev, status->cookie, &slot); if (unlikely(!ring)) @@ -1501,13 +1505,36 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, firstused = ring->current_slot - ring->used_slots + 1; if (firstused < 0) firstused = ring->nr_slots + firstused; + + skip = 0; if (unlikely(slot != firstused)) { /* This possibly is a firmware bug and will result in - * malfunction, memory leaks and/or stall of DMA functionality. */ - b43dbg(dev->wl, "Out of order TX status report on DMA ring %d. " - "Expected %d, but got %d\n", - ring->index, firstused, slot); - return; + * malfunction, memory leaks and/or stall of DMA functionality. + */ + if (slot == next_slot(ring, next_slot(ring, firstused))) { + /* If a single header/data pair was missed, skip over + * the first two slots in an attempt to recover. + */ + slot = firstused; + skip = 2; + if (!err_out1) { + /* Report the error once. */ + b43dbg(dev->wl, + "Skip on DMA ring %d slot %d.\n", + ring->index, slot); + err_out1 = 1; + } + } else { + /* More than a single header/data pair were missed. + * Report this error once. + */ + if (!err_out2) + b43dbg(dev->wl, + "Out of order TX status report on DMA ring %d. Expected %d, but got %d\n", + ring->index, firstused, slot); + err_out2 = 1; + return; + } } ops = ring->ops; @@ -1522,11 +1549,13 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, slot, firstused, ring->index); break; } + if (meta->skb) { struct b43_private_tx_info *priv_info = - b43_get_priv_tx_info(IEEE80211_SKB_CB(meta->skb)); + b43_get_priv_tx_info(IEEE80211_SKB_CB(meta->skb)); - unmap_descbuffer(ring, meta->dmaaddr, meta->skb->len, 1); + unmap_descbuffer(ring, meta->dmaaddr, + meta->skb->len, 1); kfree(priv_info->bouncebuffer); priv_info->bouncebuffer = NULL; } else { @@ -1538,8 +1567,9 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, struct ieee80211_tx_info *info; if (unlikely(!meta->skb)) { - /* This is a scatter-gather fragment of a frame, so - * the skb pointer must not be NULL. */ + /* This is a scatter-gather fragment of a frame, + * so the skb pointer must not be NULL. + */ b43dbg(dev->wl, "TX status unexpected NULL skb " "at slot %d (first=%d) on ring %d\n", slot, firstused, ring->index); @@ -1550,9 +1580,18 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, /* * Call back to inform the ieee80211 subsystem about - * the status of the transmission. + * the status of the transmission. When skipping over + * a missed TX status report, use a status structure + * filled with zeros to indicate that the frame was not + * sent (frame_count 0) and not acknowledged */ - frame_succeed = b43_fill_txstatus_report(dev, info, status); + if (unlikely(skip)) + txstat = &fake; + else + txstat = status; + + frame_succeed = b43_fill_txstatus_report(dev, info, + txstat); #ifdef CONFIG_B43_DEBUG if (frame_succeed) ring->nr_succeed_tx_packets++; @@ -1580,12 +1619,14 @@ void b43_dma_handle_txstatus(struct b43_wldev *dev, /* Everything unmapped and free'd. So it's not used anymore. */ ring->used_slots--; - if (meta->is_last_fragment) { + if (meta->is_last_fragment && !skip) { /* This is the last scatter-gather * fragment of the frame. We are done. */ break; } slot = next_slot(ring, slot); + if (skip > 0) + --skip; } if (ring->stopped) { B43_WARN_ON(free_slots(ring) < TX_SLOTS_PER_FRAME); -- cgit v1.2.3-58-ga151 From 7fc0357479eeff4ca808c4d8c09bc7631f576b8d Mon Sep 17 00:00:00 2001 From: "Luis R. Rodriguez" Date: Mon, 25 Mar 2013 11:27:46 -0700 Subject: ath9k: avoid queueing hw check work when suspended The following issue was reported. WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]() Hardware name: iMac12,1 queueing ieee80211 work while going to suspend Pid: 0, comm: swapper/0 Tainted: PF O 3.8.2-206.fc18.x86_64 #1 Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992] [] warn_slowpath_common+0x7f/0xc0 [] ? ath_start_rx_poll+0x70/0x70 [ath9k] ] warn_slowpath_fmt+0x46/0x50 [] ieee80211_can_queue_work.isra.7+0x32/0x40 Fix this by avoiding to queue the work if our device has already been marked as suspended or stopped. Reported-by: Parag Warudkar Tested-by: Parag Warudkar Cc: stable@vger.kernel.org Signed-off-by: Luis R. Rodriguez Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/link.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/ath/ath9k/link.c b/drivers/net/wireless/ath/ath9k/link.c index 39c84ecf6a42..7fdac6c7b3ea 100644 --- a/drivers/net/wireless/ath/ath9k/link.c +++ b/drivers/net/wireless/ath/ath9k/link.c @@ -170,7 +170,8 @@ void ath_rx_poll(unsigned long data) { struct ath_softc *sc = (struct ath_softc *)data; - ieee80211_queue_work(sc->hw, &sc->hw_check_work); + if (!test_bit(SC_OP_INVALID, &sc->sc_flags)) + ieee80211_queue_work(sc->hw, &sc->hw_check_work); } /* -- cgit v1.2.3-58-ga151 From ace5af39866da7d45f43774150dace19a73716d6 Mon Sep 17 00:00:00 2001 From: Colin Ian King Date: Tue, 26 Mar 2013 17:35:23 +0000 Subject: iwlegacy: 4965-rs: avoid null pointer dereference error il4965_rs_initialize_lq checks to see if sta is null, however, before that check il4965_rs_use_green dereferences sta when intializing use_green. Avoid a potential null pointer dereference error by only calling il4965_rs_use_green after we are sure sta is not null. Smatch analysis: drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn: variable dereferenced before check 'sta' (see line 2155) Signed-off-by: Colin Ian King Signed-off-by: John W. Linville --- drivers/net/wireless/iwlegacy/4965-rs.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlegacy/4965-rs.c b/drivers/net/wireless/iwlegacy/4965-rs.c index e8324b5e5bfe..6c7493c2d698 100644 --- a/drivers/net/wireless/iwlegacy/4965-rs.c +++ b/drivers/net/wireless/iwlegacy/4965-rs.c @@ -2152,7 +2152,7 @@ il4965_rs_initialize_lq(struct il_priv *il, struct ieee80211_conf *conf, int rate_idx; int i; u32 rate; - u8 use_green = il4965_rs_use_green(il, sta); + u8 use_green; u8 active_tbl = 0; u8 valid_tx_ant; struct il_station_priv *sta_priv; @@ -2160,6 +2160,7 @@ il4965_rs_initialize_lq(struct il_priv *il, struct ieee80211_conf *conf, if (!sta || !lq_sta) return; + use_green = il4965_rs_use_green(il, sta); sta_priv = (void *)sta->drv_priv; i = lq_sta->last_txrate_idx; -- cgit v1.2.3-58-ga151 From 2e1253d640eb7f8707d2591c93097c1e9f9c71d5 Mon Sep 17 00:00:00 2001 From: Rafał Miłecki Date: Wed, 27 Mar 2013 08:37:08 +0100 Subject: b43: N-PHY: use more bits for offset in RSSI calibration MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit When calculating "offset" for final RSSI calibration we're using numbers bigger than s8 can hold. We have for example: offset[j] = 232 - poll_results[j]; formula. If poll_results[j] is small enough (it usually is) we treat number's bit as a sign bit. For example 232 - 1 becomes: 0xE8 - 0x1 = 0xE7, which is not 231 but -25. This code was introduced in e0c9a0219a8f542e3946fe972a68aacf8c3f906c and caused stability regression on some cards, for ex. BCM4322. Signed-off-by: Rafał Miłecki Cc: stable@vger.kernel.org Signed-off-by: John W. Linville --- drivers/net/wireless/b43/phy_n.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/b43/phy_n.c b/drivers/net/wireless/b43/phy_n.c index e014a7a8154d..e8486c1e091a 100644 --- a/drivers/net/wireless/b43/phy_n.c +++ b/drivers/net/wireless/b43/phy_n.c @@ -1564,7 +1564,7 @@ static void b43_nphy_rev3_rssi_cal(struct b43_wldev *dev) u16 clip_off[2] = { 0xFFFF, 0xFFFF }; u8 vcm_final = 0; - s8 offset[4]; + s32 offset[4]; s32 results[8][4] = { }; s32 results_min[4] = { }; s32 poll_results[4] = { }; @@ -1732,7 +1732,7 @@ static void b43_nphy_rev2_rssi_cal(struct b43_wldev *dev, u8 type) u8 regs_save_radio[2]; u16 regs_save_phy[2]; - s8 offset[4]; + s32 offset[4]; u8 core; u8 rail; -- cgit v1.2.3-58-ga151 From 14109a59caf93e6eae726a34bf2f0897508ec8c1 Mon Sep 17 00:00:00 2001 From: Frank Li Date: Tue, 26 Mar 2013 16:12:03 +0000 Subject: enet: fec: fix fail resume from suspend state Without this patch 1. boot with nfs (no_console_suspend) 2. echo mem >/sys/power/state 3. wakeup by wakesource 4. print "eth0: tx queue full" This fix above problem by reinit bd queue at restart function Signed-off-by: Frank Li Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fec.c | 82 ++++++++++++++++++++++-------------- 1 file changed, 50 insertions(+), 32 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/freescale/fec.c b/drivers/net/ethernet/freescale/fec.c index 911d0253dbb2..f292c3aa423f 100644 --- a/drivers/net/ethernet/freescale/fec.c +++ b/drivers/net/ethernet/freescale/fec.c @@ -345,6 +345,53 @@ fec_enet_start_xmit(struct sk_buff *skb, struct net_device *ndev) return NETDEV_TX_OK; } +/* Init RX & TX buffer descriptors + */ +static void fec_enet_bd_init(struct net_device *dev) +{ + struct fec_enet_private *fep = netdev_priv(dev); + struct bufdesc *bdp; + unsigned int i; + + /* Initialize the receive buffer descriptors. */ + bdp = fep->rx_bd_base; + for (i = 0; i < RX_RING_SIZE; i++) { + + /* Initialize the BD for every fragment in the page. */ + if (bdp->cbd_bufaddr) + bdp->cbd_sc = BD_ENET_RX_EMPTY; + else + bdp->cbd_sc = 0; + bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); + } + + /* Set the last buffer to wrap */ + bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); + bdp->cbd_sc |= BD_SC_WRAP; + + fep->cur_rx = fep->rx_bd_base; + + /* ...and the same for transmit */ + bdp = fep->tx_bd_base; + fep->cur_tx = bdp; + for (i = 0; i < TX_RING_SIZE; i++) { + + /* Initialize the BD for every fragment in the page. */ + bdp->cbd_sc = 0; + if (bdp->cbd_bufaddr && fep->tx_skbuff[i]) { + dev_kfree_skb_any(fep->tx_skbuff[i]); + fep->tx_skbuff[i] = NULL; + } + bdp->cbd_bufaddr = 0; + bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); + } + + /* Set the last buffer to wrap */ + bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); + bdp->cbd_sc |= BD_SC_WRAP; + fep->dirty_tx = bdp; +} + /* This function is called to start or restart the FEC during a link * change. This only happens when switching between half and full * duplex. @@ -388,6 +435,8 @@ fec_restart(struct net_device *ndev, int duplex) /* Set maximum receive buffer size. */ writel(PKT_MAXBLR_SIZE, fep->hwp + FEC_R_BUFF_SIZE); + fec_enet_bd_init(ndev); + /* Set receive and transmit descriptor base. */ writel(fep->bd_dma, fep->hwp + FEC_R_DES_START); if (fep->bufdesc_ex) @@ -397,7 +446,6 @@ fec_restart(struct net_device *ndev, int duplex) writel((unsigned long)fep->bd_dma + sizeof(struct bufdesc) * RX_RING_SIZE, fep->hwp + FEC_X_DES_START); - fep->cur_rx = fep->rx_bd_base; for (i = 0; i <= TX_RING_MOD_MASK; i++) { if (fep->tx_skbuff[i]) { @@ -1597,8 +1645,6 @@ static int fec_enet_init(struct net_device *ndev) { struct fec_enet_private *fep = netdev_priv(ndev); struct bufdesc *cbd_base; - struct bufdesc *bdp; - unsigned int i; /* Allocate memory for buffer descriptors. */ cbd_base = dma_alloc_coherent(NULL, PAGE_SIZE, &fep->bd_dma, @@ -1608,6 +1654,7 @@ static int fec_enet_init(struct net_device *ndev) return -ENOMEM; } + memset(cbd_base, 0, PAGE_SIZE); spin_lock_init(&fep->hw_lock); fep->netdev = ndev; @@ -1631,35 +1678,6 @@ static int fec_enet_init(struct net_device *ndev) writel(FEC_RX_DISABLED_IMASK, fep->hwp + FEC_IMASK); netif_napi_add(ndev, &fep->napi, fec_enet_rx_napi, FEC_NAPI_WEIGHT); - /* Initialize the receive buffer descriptors. */ - bdp = fep->rx_bd_base; - for (i = 0; i < RX_RING_SIZE; i++) { - - /* Initialize the BD for every fragment in the page. */ - bdp->cbd_sc = 0; - bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); - } - - /* Set the last buffer to wrap */ - bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); - bdp->cbd_sc |= BD_SC_WRAP; - - /* ...and the same for transmit */ - bdp = fep->tx_bd_base; - fep->cur_tx = bdp; - for (i = 0; i < TX_RING_SIZE; i++) { - - /* Initialize the BD for every fragment in the page. */ - bdp->cbd_sc = 0; - bdp->cbd_bufaddr = 0; - bdp = fec_enet_get_nextdesc(bdp, fep->bufdesc_ex); - } - - /* Set the last buffer to wrap */ - bdp = fec_enet_get_prevdesc(bdp, fep->bufdesc_ex); - bdp->cbd_sc |= BD_SC_WRAP; - fep->dirty_tx = bdp; - fec_restart(ndev, 0); return 0; -- cgit v1.2.3-58-ga151 From b56d6b3fca6d1214dbc9c5655f26e5d4ec04afc8 Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Wed, 27 Mar 2013 04:41:59 +0000 Subject: drivers: net: ethernet: cpsw: use netif_wake_queue() while restarting tx queue To restart tx queue use netif_wake_queue() intead of netif_start_queue() so that net schedule will restart transmission immediately which will increase network performance while doing huge data transfers. Reported-by: Dan Franke Suggested-by: Sriramakrishnan A G Signed-off-by: Mugunthan V N Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/cpsw.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/ti/cpsw.c b/drivers/net/ethernet/ti/cpsw.c index df32a090d08e..80cad06e5eb2 100644 --- a/drivers/net/ethernet/ti/cpsw.c +++ b/drivers/net/ethernet/ti/cpsw.c @@ -436,7 +436,7 @@ void cpsw_tx_handler(void *token, int len, int status) * queue is stopped then start the queue as we have free desc for tx */ if (unlikely(netif_queue_stopped(ndev))) - netif_start_queue(ndev); + netif_wake_queue(ndev); cpts_tx_timestamp(priv->cpts, skb); priv->stats.tx_packets++; priv->stats.tx_bytes += len; -- cgit v1.2.3-58-ga151 From 7e51cde276ca820d526c6c21cf8147df595a36bf Mon Sep 17 00:00:00 2001 From: Mugunthan V N Date: Wed, 27 Mar 2013 04:42:00 +0000 Subject: drivers: net: ethernet: davinci_emac: use netif_wake_queue() while restarting tx queue To restart tx queue use netif_wake_queue() intead of netif_start_queue() so that net schedule will restart transmission immediately which will increase network performance while doing huge data transfers. Reported-by: Dan Franke Suggested-by: Sriramakrishnan A G Signed-off-by: Mugunthan V N Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/ethernet/ti/davinci_emac.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/ti/davinci_emac.c b/drivers/net/ethernet/ti/davinci_emac.c index ae1b77aa199f..72300bc9e378 100644 --- a/drivers/net/ethernet/ti/davinci_emac.c +++ b/drivers/net/ethernet/ti/davinci_emac.c @@ -1053,7 +1053,7 @@ static void emac_tx_handler(void *token, int len, int status) * queue is stopped then start the queue as we have free desc for tx */ if (unlikely(netif_queue_stopped(ndev))) - netif_start_queue(ndev); + netif_wake_queue(ndev); ndev->stats.tx_packets++; ndev->stats.tx_bytes += len; dev_kfree_skb_any(skb); -- cgit v1.2.3-58-ga151 From 715230a44310a8cf66fbfb5a46f9a62a9b2de424 Mon Sep 17 00:00:00 2001 From: Kees Cook Date: Wed, 27 Mar 2013 06:40:50 +0000 Subject: tg3: fix length overflow in VPD firmware parsing Commit 184b89044fb6e2a74611dafa69b1dce0d98612c6 ("tg3: Use VPD fw version when present") introduced VPD parsing that contained a potential length overflow. Limit the hardware's reported firmware string length (max 255 bytes) to stay inside the driver's firmware string length (32 bytes). On overflow, truncate the formatted firmware string instead of potentially overwriting portions of the tg3 struct. http://cansecwest.com/slides/2013/PrivateCore%20CSW%202013.pdf Signed-off-by: Kees Cook Reported-by: Oded Horovitz Reported-by: Brad Spengler Cc: stable@vger.kernel.org Cc: Matt Carlson Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/tg3.c | 7 +++++-- 1 file changed, 5 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 67d2663b3974..17a972734ba7 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -14604,8 +14604,11 @@ static void tg3_read_vpd(struct tg3 *tp) if (j + len > block_end) goto partno; - memcpy(tp->fw_ver, &vpd_data[j], len); - strncat(tp->fw_ver, " bc ", vpdlen - len - 1); + if (len >= sizeof(tp->fw_ver)) + len = sizeof(tp->fw_ver) - 1; + memset(tp->fw_ver, 0, sizeof(tp->fw_ver)); + snprintf(tp->fw_ver, sizeof(tp->fw_ver), "%.*s bc ", len, + &vpd_data[j]); } partno: -- cgit v1.2.3-58-ga151 From b8730b403aee94db4631bfefb546a6ce8c287dc2 Mon Sep 17 00:00:00 2001 From: Johannes Berg Date: Wed, 27 Mar 2013 20:49:58 +0100 Subject: iwlwifi: dvm: fix the passive-no-RX workaround Alex Romosan reported that since the mac80211 changes in "mac80211: start auth/assoc timeout on frame status" and the subsequent fixes in "mac80211: fix auth/assoc timeout handling" (commits 1672c0e31917 and 89afe614c0c) there's sometimes an issue connecting to a 5 GHz network with the iwlwifi DVM driver. The reason appears to be that since these commits any bad TX status makes mac80211 immediately try again, causing all of the authentication attempts to be quickly rejected by the firmware as it hasn't heard a beacon yet. Before, it would wait for the timeout regardless of status. To fix this, invoke the passive-no-RX workaround when not associated yet as well. This will cause the first frame to get lost, but then the driver will stop the queues and the second attempt will only be transmitted after hearing a beacon, thus delaying it appropriately to not make the firmware reject it again. Reported-by: Alex Romosan Tested-by: Alex Romosan Signed-off-by: Johannes Berg --- drivers/net/wireless/iwlwifi/dvm/rxon.c | 18 ++++++++---------- drivers/net/wireless/iwlwifi/dvm/tx.c | 2 +- 2 files changed, 9 insertions(+), 11 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/iwlwifi/dvm/rxon.c b/drivers/net/wireless/iwlwifi/dvm/rxon.c index 23be948cf162..a82b6b39d4ff 100644 --- a/drivers/net/wireless/iwlwifi/dvm/rxon.c +++ b/drivers/net/wireless/iwlwifi/dvm/rxon.c @@ -1419,6 +1419,14 @@ void iwlagn_bss_info_changed(struct ieee80211_hw *hw, mutex_lock(&priv->mutex); + if (changes & BSS_CHANGED_IDLE && bss_conf->idle) { + /* + * If we go idle, then clearly no "passive-no-rx" + * workaround is needed any more, this is a reset. + */ + iwlagn_lift_passive_no_rx(priv); + } + if (unlikely(!iwl_is_ready(priv))) { IWL_DEBUG_MAC80211(priv, "leave - not ready\n"); mutex_unlock(&priv->mutex); @@ -1450,16 +1458,6 @@ void iwlagn_bss_info_changed(struct ieee80211_hw *hw, priv->timestamp = bss_conf->sync_tsf; ctx->staging.filter_flags |= RXON_FILTER_ASSOC_MSK; } else { - /* - * If we disassociate while there are pending - * frames, just wake up the queues and let the - * frames "escape" ... This shouldn't really - * be happening to start with, but we should - * not get stuck in this case either since it - * can happen if userspace gets confused. - */ - iwlagn_lift_passive_no_rx(priv); - ctx->staging.filter_flags &= ~RXON_FILTER_ASSOC_MSK; if (ctx->ctxid == IWL_RXON_CTX_BSS) diff --git a/drivers/net/wireless/iwlwifi/dvm/tx.c b/drivers/net/wireless/iwlwifi/dvm/tx.c index 6aec2df3bb27..d1a670d7b10c 100644 --- a/drivers/net/wireless/iwlwifi/dvm/tx.c +++ b/drivers/net/wireless/iwlwifi/dvm/tx.c @@ -1192,7 +1192,7 @@ int iwlagn_rx_reply_tx(struct iwl_priv *priv, struct iwl_rx_cmd_buffer *rxb, memset(&info->status, 0, sizeof(info->status)); if (status == TX_STATUS_FAIL_PASSIVE_NO_RX && - iwl_is_associated_ctx(ctx) && ctx->vif && + ctx->vif && ctx->vif->type == NL80211_IFTYPE_STATION) { /* block and stop all queues */ priv->passive_no_rx = true; -- cgit v1.2.3-58-ga151 From 9cfe8b156c21cf340b3a10ecb3022fbbc1c39185 Mon Sep 17 00:00:00 2001 From: Mirko Lindner Date: Tue, 26 Mar 2013 06:38:35 +0000 Subject: sky2: Receive Overflows not counted The sky2 driver doesn't count the Receive Overflows because the MAC interrupt for this event is not set in the MAC's interrupt mask. The MAC's interrupt mask is set only for Transmit FIFO Underruns. Fix: The correct setting should be (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR) Otherwise the Receive Overflow event will not generate any interrupt. The Receive Overflow interrupt is handled correctly Signed-off-by: Mirko Lindner Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/sky2.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/marvell/sky2.h b/drivers/net/ethernet/marvell/sky2.h index 615ac63ea860..ec6dcd80152b 100644 --- a/drivers/net/ethernet/marvell/sky2.h +++ b/drivers/net/ethernet/marvell/sky2.h @@ -2074,7 +2074,7 @@ enum { GM_IS_RX_FF_OR = 1<<1, /* Receive FIFO Overrun */ GM_IS_RX_COMPL = 1<<0, /* Frame Reception Complete */ -#define GMAC_DEF_MSK GM_IS_TX_FF_UR +#define GMAC_DEF_MSK (GM_IS_TX_FF_UR | GM_IS_RX_FF_OR) }; /* GMAC_LINK_CTRL 16 bit GMAC Link Control Reg (YUKON only) */ -- cgit v1.2.3-58-ga151 From 74f9f42c1c1650e74fb464f76644c9041f996851 Mon Sep 17 00:00:00 2001 From: Mirko Lindner Date: Tue, 26 Mar 2013 06:38:42 +0000 Subject: sky2: Threshold for Pause Packet is set wrong The sky2 driver sets the Rx Upper Threshold for Pause Packet generation to a wrong value which leads to only 2kB of RAM remaining space. This can lead to Rx overflow errors even with activated flow-control. Fix: We should increase the value to 8192/8 Signed-off-by: Mirko Lindner Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/sky2.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c index fc07ca35721b..6a0e671fcecd 100644 --- a/drivers/net/ethernet/marvell/sky2.c +++ b/drivers/net/ethernet/marvell/sky2.c @@ -1067,7 +1067,7 @@ static void sky2_ramset(struct sky2_hw *hw, u16 q, u32 start, u32 space) sky2_write32(hw, RB_ADDR(q, RB_RX_UTHP), tp); sky2_write32(hw, RB_ADDR(q, RB_RX_LTHP), space/2); - tp = space - 2048/8; + tp = space - 8192/8; sky2_write32(hw, RB_ADDR(q, RB_RX_UTPP), tp); sky2_write32(hw, RB_ADDR(q, RB_RX_LTPP), space/4); } else { -- cgit v1.2.3-58-ga151 From 1bc7db16782c2a581fb4d53ca853631050f31611 Mon Sep 17 00:00:00 2001 From: "nikolay@redhat.com" Date: Wed, 27 Mar 2013 03:32:41 +0000 Subject: bonding: fix disabling of arp_interval and miimon Currently if either arp_interval or miimon is disabled, they both get disabled, and upon disabling they get executed once more which is not the proper behaviour. Also when doing a no-op and disabling an already disabled one, the other again gets disabled. Also fix the error messages with the proper valid ranges, and a small typo fix in the up delay error message (outputting "down delay", instead of "up delay"). Signed-off-by: Nikolay Aleksandrov Signed-off-by: David S. Miller --- drivers/net/bonding/bond_sysfs.c | 92 +++++++++++++++++++++------------------- 1 file changed, 48 insertions(+), 44 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_sysfs.c b/drivers/net/bonding/bond_sysfs.c index db103e03ba05..ea7a388f4843 100644 --- a/drivers/net/bonding/bond_sysfs.c +++ b/drivers/net/bonding/bond_sysfs.c @@ -527,7 +527,7 @@ static ssize_t bonding_store_arp_interval(struct device *d, goto out; } if (new_value < 0) { - pr_err("%s: Invalid arp_interval value %d not in range 1-%d; rejected.\n", + pr_err("%s: Invalid arp_interval value %d not in range 0-%d; rejected.\n", bond->dev->name, new_value, INT_MAX); ret = -EINVAL; goto out; @@ -542,14 +542,15 @@ static ssize_t bonding_store_arp_interval(struct device *d, pr_info("%s: Setting ARP monitoring interval to %d.\n", bond->dev->name, new_value); bond->params.arp_interval = new_value; - if (bond->params.miimon) { - pr_info("%s: ARP monitoring cannot be used with MII monitoring. %s Disabling MII monitoring.\n", - bond->dev->name, bond->dev->name); - bond->params.miimon = 0; - } - if (!bond->params.arp_targets[0]) { - pr_info("%s: ARP monitoring has been set up, but no ARP targets have been specified.\n", - bond->dev->name); + if (new_value) { + if (bond->params.miimon) { + pr_info("%s: ARP monitoring cannot be used with MII monitoring. %s Disabling MII monitoring.\n", + bond->dev->name, bond->dev->name); + bond->params.miimon = 0; + } + if (!bond->params.arp_targets[0]) + pr_info("%s: ARP monitoring has been set up, but no ARP targets have been specified.\n", + bond->dev->name); } if (bond->dev->flags & IFF_UP) { /* If the interface is up, we may need to fire off @@ -557,10 +558,13 @@ static ssize_t bonding_store_arp_interval(struct device *d, * timer will get fired off when the open function * is called. */ - cancel_delayed_work_sync(&bond->mii_work); - queue_delayed_work(bond->wq, &bond->arp_work, 0); + if (!new_value) { + cancel_delayed_work_sync(&bond->arp_work); + } else { + cancel_delayed_work_sync(&bond->mii_work); + queue_delayed_work(bond->wq, &bond->arp_work, 0); + } } - out: rtnl_unlock(); return ret; @@ -702,7 +706,7 @@ static ssize_t bonding_store_downdelay(struct device *d, } if (new_value < 0) { pr_err("%s: Invalid down delay value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; } else { @@ -757,8 +761,8 @@ static ssize_t bonding_store_updelay(struct device *d, goto out; } if (new_value < 0) { - pr_err("%s: Invalid down delay value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + pr_err("%s: Invalid up delay value %d not in range %d-%d; rejected.\n", + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; } else { @@ -968,37 +972,37 @@ static ssize_t bonding_store_miimon(struct device *d, } if (new_value < 0) { pr_err("%s: Invalid miimon value %d not in range %d-%d; rejected.\n", - bond->dev->name, new_value, 1, INT_MAX); + bond->dev->name, new_value, 0, INT_MAX); ret = -EINVAL; goto out; - } else { - pr_info("%s: Setting MII monitoring interval to %d.\n", - bond->dev->name, new_value); - bond->params.miimon = new_value; - if (bond->params.updelay) - pr_info("%s: Note: Updating updelay (to %d) since it is a multiple of the miimon value.\n", - bond->dev->name, - bond->params.updelay * bond->params.miimon); - if (bond->params.downdelay) - pr_info("%s: Note: Updating downdelay (to %d) since it is a multiple of the miimon value.\n", - bond->dev->name, - bond->params.downdelay * bond->params.miimon); - if (bond->params.arp_interval) { - pr_info("%s: MII monitoring cannot be used with ARP monitoring. Disabling ARP monitoring...\n", - bond->dev->name); - bond->params.arp_interval = 0; - if (bond->params.arp_validate) { - bond->params.arp_validate = - BOND_ARP_VALIDATE_NONE; - } - } - - if (bond->dev->flags & IFF_UP) { - /* If the interface is up, we may need to fire off - * the MII timer. If the interface is down, the - * timer will get fired off when the open function - * is called. - */ + } + pr_info("%s: Setting MII monitoring interval to %d.\n", + bond->dev->name, new_value); + bond->params.miimon = new_value; + if (bond->params.updelay) + pr_info("%s: Note: Updating updelay (to %d) since it is a multiple of the miimon value.\n", + bond->dev->name, + bond->params.updelay * bond->params.miimon); + if (bond->params.downdelay) + pr_info("%s: Note: Updating downdelay (to %d) since it is a multiple of the miimon value.\n", + bond->dev->name, + bond->params.downdelay * bond->params.miimon); + if (new_value && bond->params.arp_interval) { + pr_info("%s: MII monitoring cannot be used with ARP monitoring. Disabling ARP monitoring...\n", + bond->dev->name); + bond->params.arp_interval = 0; + if (bond->params.arp_validate) + bond->params.arp_validate = BOND_ARP_VALIDATE_NONE; + } + if (bond->dev->flags & IFF_UP) { + /* If the interface is up, we may need to fire off + * the MII timer. If the interface is down, the + * timer will get fired off when the open function + * is called. + */ + if (!new_value) { + cancel_delayed_work_sync(&bond->mii_work); + } else { cancel_delayed_work_sync(&bond->arp_work); queue_delayed_work(bond->wq, &bond->mii_work, 0); } -- cgit v1.2.3-58-ga151 From 4c51e53689569398d656e631c17308d9b8e84650 Mon Sep 17 00:00:00 2001 From: Steve Glendinning Date: Thu, 28 Mar 2013 02:34:41 +0000 Subject: smsc75xx: fix jumbo frame support This patch enables RX of jumbo frames for LAN7500. Previously the driver would transmit jumbo frames succesfully but would drop received jumbo frames (incrementing the interface errors count). With this patch applied the device can succesfully receive jumbo frames up to MTU 9000 (9014 bytes on the wire including ethernet header). Signed-off-by: Steve Glendinning Signed-off-by: David S. Miller --- drivers/net/usb/smsc75xx.c | 12 ++++++++---- 1 file changed, 8 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/usb/smsc75xx.c b/drivers/net/usb/smsc75xx.c index 9abe51710f22..1a15ec14c386 100644 --- a/drivers/net/usb/smsc75xx.c +++ b/drivers/net/usb/smsc75xx.c @@ -914,8 +914,12 @@ static int smsc75xx_set_rx_max_frame_length(struct usbnet *dev, int size) static int smsc75xx_change_mtu(struct net_device *netdev, int new_mtu) { struct usbnet *dev = netdev_priv(netdev); + int ret; + + if (new_mtu > MAX_SINGLE_PACKET_SIZE) + return -EINVAL; - int ret = smsc75xx_set_rx_max_frame_length(dev, new_mtu); + ret = smsc75xx_set_rx_max_frame_length(dev, new_mtu + ETH_HLEN); if (ret < 0) { netdev_warn(dev->net, "Failed to set mac rx frame length\n"); return ret; @@ -1324,7 +1328,7 @@ static int smsc75xx_reset(struct usbnet *dev) netif_dbg(dev, ifup, dev->net, "FCT_TX_CTL set to 0x%08x\n", buf); - ret = smsc75xx_set_rx_max_frame_length(dev, 1514); + ret = smsc75xx_set_rx_max_frame_length(dev, dev->net->mtu + ETH_HLEN); if (ret < 0) { netdev_warn(dev->net, "Failed to set max rx frame length\n"); return ret; @@ -2134,8 +2138,8 @@ static int smsc75xx_rx_fixup(struct usbnet *dev, struct sk_buff *skb) else if (rx_cmd_a & (RX_CMD_A_LONG | RX_CMD_A_RUNT)) dev->net->stats.rx_frame_errors++; } else { - /* ETH_FRAME_LEN + 4(CRC) + 2(COE) + 4(Vlan) */ - if (unlikely(size > (ETH_FRAME_LEN + 12))) { + /* MAX_SINGLE_PACKET_SIZE + 4(CRC) + 2(COE) + 4(Vlan) */ + if (unlikely(size > (MAX_SINGLE_PACKET_SIZE + ETH_HLEN + 12))) { netif_dbg(dev, rx_err, dev->net, "size err rx_cmd_a=0x%08x\n", rx_cmd_a); -- cgit v1.2.3-58-ga151 From dc574f1d52d893f516f3786ff7635450bac00eef Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Thu, 28 Mar 2013 11:32:44 +0000 Subject: net: calxedaxgmac: fix rx ring handling when OOM If skb allocation for the rx ring fails repeatedly, we can reach a point were the ring is empty. In this condition, the driver is out of sync with the h/w. While this has always been possible, the removal of the skb recycling seems to have made triggering this problem easier. Signed-off-by: Rob Herring Signed-off-by: David S. Miller --- drivers/net/ethernet/calxeda/xgmac.c | 3 +++ 1 file changed, 3 insertions(+) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/calxeda/xgmac.c b/drivers/net/ethernet/calxeda/xgmac.c index a170065b5973..bb1e80bfa78a 100644 --- a/drivers/net/ethernet/calxeda/xgmac.c +++ b/drivers/net/ethernet/calxeda/xgmac.c @@ -1141,6 +1141,9 @@ static int xgmac_rx(struct xgmac_priv *priv, int limit) struct sk_buff *skb; int frame_len; + if (!dma_ring_cnt(priv->rx_head, priv->rx_tail, DMA_RX_RING_SZ)) + break; + entry = priv->rx_tail; p = priv->dma_rx + entry; if (desc_get_owner(p)) -- cgit v1.2.3-58-ga151 From e6c3827dcfe53dd78b824d2ee4007a216ada739e Mon Sep 17 00:00:00 2001 From: Rob Herring Date: Thu, 28 Mar 2013 11:32:45 +0000 Subject: net: calxedaxgmac: Wake-on-LAN fixes WOL is broken because the magic packet status bit is getting set rather than the enable bit. The PMT interrupt is not getting serviced because the PMT interrupt is also enabled on the global interrupt, but not cleared by the global interrupt and the global interrupt is higher priority. This fixes both of these issues to get WOL working. There's still a problem with receive after resume, but at least now we can wake-up. Signed-off-by: Rob Herring Signed-off-by: David S. Miller --- drivers/net/ethernet/calxeda/xgmac.c | 6 +++++- 1 file changed, 5 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/calxeda/xgmac.c b/drivers/net/ethernet/calxeda/xgmac.c index bb1e80bfa78a..b0ebc9f6d55e 100644 --- a/drivers/net/ethernet/calxeda/xgmac.c +++ b/drivers/net/ethernet/calxeda/xgmac.c @@ -163,6 +163,7 @@ #define XGMAC_FLOW_CTRL_FCB_BPA 0x00000001 /* Flow Control Busy ... */ /* XGMAC_INT_STAT reg */ +#define XGMAC_INT_STAT_PMTIM 0x00800000 /* PMT Interrupt Mask */ #define XGMAC_INT_STAT_PMT 0x0080 /* PMT Interrupt Status */ #define XGMAC_INT_STAT_LPI 0x0040 /* LPI Interrupt Status */ @@ -960,6 +961,9 @@ static int xgmac_hw_init(struct net_device *dev) writel(DMA_INTR_DEFAULT_MASK, ioaddr + XGMAC_DMA_STATUS); writel(DMA_INTR_DEFAULT_MASK, ioaddr + XGMAC_DMA_INTR_ENA); + /* Mask power mgt interrupt */ + writel(XGMAC_INT_STAT_PMTIM, ioaddr + XGMAC_INT_STAT); + /* XGMAC requires AXI bus init. This is a 'magic number' for now */ writel(0x0077000E, ioaddr + XGMAC_DMA_AXI_BUS); @@ -1828,7 +1832,7 @@ static void xgmac_pmt(void __iomem *ioaddr, unsigned long mode) unsigned int pmt = 0; if (mode & WAKE_MAGIC) - pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_MAGIC_PKT; + pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_MAGIC_PKT_EN; if (mode & WAKE_UCAST) pmt |= XGMAC_PMT_POWERDOWN | XGMAC_PMT_GLBL_UNICAST; -- cgit v1.2.3-58-ga151 From 188ab1b105c96656f6bcfb49d0d8bb1b1936b632 Mon Sep 17 00:00:00 2001 From: Hannes Frederic Sowa Date: Thu, 28 Mar 2013 18:10:50 +0000 Subject: atl1e: drop pci-msi support because of packet corruption MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Usage of pci-msi results in corrupted dma packet transfers to the host. Reported-by: rebelyouth Cc: Huang, Xiong Tested-by: Christian Sünkenberg Signed-off-by: Hannes Frederic Sowa Signed-off-by: David S. Miller --- drivers/net/ethernet/atheros/atl1e/atl1e.h | 1 - drivers/net/ethernet/atheros/atl1e/atl1e_main.c | 19 ++----------------- 2 files changed, 2 insertions(+), 18 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e.h b/drivers/net/ethernet/atheros/atl1e/atl1e.h index 829b5ad71d0d..edfdf6b950e7 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e.h +++ b/drivers/net/ethernet/atheros/atl1e/atl1e.h @@ -438,7 +438,6 @@ struct atl1e_adapter { struct atl1e_hw hw; struct atl1e_hw_stats hw_stats; - bool have_msi; u32 wol; u16 link_speed; u16 link_duplex; diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c index 92f4734f860d..f73d5609439a 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c +++ b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c @@ -1849,34 +1849,19 @@ static void atl1e_free_irq(struct atl1e_adapter *adapter) struct net_device *netdev = adapter->netdev; free_irq(adapter->pdev->irq, netdev); - - if (adapter->have_msi) - pci_disable_msi(adapter->pdev); } static int atl1e_request_irq(struct atl1e_adapter *adapter) { struct pci_dev *pdev = adapter->pdev; struct net_device *netdev = adapter->netdev; - int flags = 0; int err = 0; - adapter->have_msi = true; - err = pci_enable_msi(pdev); - if (err) { - netdev_dbg(netdev, - "Unable to allocate MSI interrupt Error: %d\n", err); - adapter->have_msi = false; - } - - if (!adapter->have_msi) - flags |= IRQF_SHARED; - err = request_irq(pdev->irq, atl1e_intr, flags, netdev->name, netdev); + err = request_irq(pdev->irq, atl1e_intr, IRQF_SHARED, netdev->name, + netdev); if (err) { netdev_dbg(adapter->netdev, "Unable to allocate interrupt Error: %d\n", err); - if (adapter->have_msi) - pci_disable_msi(pdev); return err; } netdev_dbg(netdev, "atl1e_request_irq OK\n"); -- cgit v1.2.3-58-ga151 From 14bc435ea54cb888409efb54fc6b76c13ef530e9 Mon Sep 17 00:00:00 2001 From: "Max.Nekludov@us.elster.com" Date: Fri, 29 Mar 2013 05:27:36 +0000 Subject: ks8851: Fix interpretation of rxlen field. According to the Datasheet (page 52): 15-12 Reserved 11-0 RXBC Receive Byte Count This field indicates the present received frame byte size. The code has a bug: rxh = ks8851_rdreg32(ks, KS_RXFHSR); rxstat = rxh & 0xffff; rxlen = rxh >> 16; // BUG!!! 0xFFF mask should be applied Signed-off-by: Max Nekludov Signed-off-by: David S. Miller --- drivers/net/ethernet/micrel/ks8851.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/micrel/ks8851.c b/drivers/net/ethernet/micrel/ks8851.c index 33bcb63d56a2..8fb481252e2c 100644 --- a/drivers/net/ethernet/micrel/ks8851.c +++ b/drivers/net/ethernet/micrel/ks8851.c @@ -528,7 +528,7 @@ static void ks8851_rx_pkts(struct ks8851_net *ks) for (; rxfc != 0; rxfc--) { rxh = ks8851_rdreg32(ks, KS_RXFHSR); rxstat = rxh & 0xffff; - rxlen = rxh >> 16; + rxlen = (rxh >> 16) & 0xfff; netif_dbg(ks, rx_status, ks->netdev, "rx: stat 0x%04x, len 0x%04x\n", rxstat, rxlen); -- cgit v1.2.3-58-ga151 From 1e1b812bbe1069fc8e2e372dca7d5f541c7a8ceb Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 09:50:07 +0000 Subject: sh_eth: fix handling of no LINK signal The code handling the absent LINK signal (or the absent PSR register -- which reflects the state of this signal) is quite naive and has probably never really worked. It's probably enough to say that this code is executed only on the LINK change interrupt (sic!) but even if we actually have the signal and choose to ignore it (it might be connected to PHY's link/activity LED output as on the Renesas BOCK-W board), sh_eth_adjust_link() on which this code relies to update 'mdp->link' gets executed later than the LINK change interrupt where it is checked, and so RX/TX never get enabled via ECMR register. So, ignore the LINK changed interrupt iff LINK signal is absent (or just chosen not to be used) or PSR register is absent, and enable/disable RX/TX directly in sh_eth_adjust_link() in this case. Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 10 ++++++---- 1 file changed, 6 insertions(+), 4 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index bf5e3cf97c4d..1ca8b2b10adc 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1216,10 +1216,7 @@ static void sh_eth_error(struct net_device *ndev, int intr_status) if (felic_stat & ECSR_LCHNG) { /* Link Changed */ if (mdp->cd->no_psr || mdp->no_ether_link) { - if (mdp->link == PHY_DOWN) - link_stat = 0; - else - link_stat = PHY_ST_LINK; + goto ignore_link; } else { link_stat = (sh_eth_read(ndev, PSR)); if (mdp->ether_link_active_low) @@ -1242,6 +1239,7 @@ static void sh_eth_error(struct net_device *ndev, int intr_status) } } +ignore_link: if (intr_status & EESR_TWB) { /* Write buck end. unused write back interrupt */ if (intr_status & EESR_TABT) /* Transmit Abort int */ @@ -1392,12 +1390,16 @@ static void sh_eth_adjust_link(struct net_device *ndev) (sh_eth_read(ndev, ECMR) & ~ECMR_TXF), ECMR); new_state = 1; mdp->link = phydev->link; + if (mdp->cd->no_psr || mdp->no_ether_link) + sh_eth_rcv_snd_enable(ndev); } } else if (mdp->link) { new_state = 1; mdp->link = PHY_DOWN; mdp->speed = 0; mdp->duplex = -1; + if (mdp->cd->no_psr || mdp->no_ether_link) + sh_eth_rcv_snd_disable(ndev); } if (new_state && netif_msg_link(mdp)) -- cgit v1.2.3-58-ga151 From 3893b27345ac0ff13c1b9ec20ad50966b810997e Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 09:54:20 +0000 Subject: sh_eth: workaround for spurious ECI interrupt At least on Renesas R8A7778, EESR.ECI interrupt seems to fire regardless of its mask in EESIPR register. I can 100% reproduce it with the following scenario: target is booted with 'ip=on' option, and so IP-Config opens SoC Ether device but doesn't get a proper reply and then succeeds with on-board SMC chip; then I login and try to bring up the SoC Ether device with 'ifconfig', and I get an ECI interrupt once request_irq() is called by sh_eth_open() (while interrupt mask in EESIPR register is all 0), if that interrupt is accompanied by a pending EESR.FRC (frame receive completion) interrupt, I get kernel oops in sh_eth_rx() because sh_eth_ring_init() hasn't been called yet! The solution I worked out is the following: in sh_eth_interrupt(), mask the interrupt status from EESR register with the interrupt mask from EESIPR register in order not to handle the disabled interrupts -- but forcing EESIPR.M_ECI bit in this mask set because we always need to fully handle EESR.ECI interrupt in sh_eth_error() in order to quench it (as it doesn't get cleared by just writing 1 to the this bit as all the other interrupts). While at it, remove unneeded initializer for 'intr_status' variable and give it *unsigned long* type, matching the type of sh_eth_read()'s result; fix comment. Signed-off-by: Sergei Shtylyov Reviewed-by: Max Filippov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 10 ++++++++-- 1 file changed, 8 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 1ca8b2b10adc..44f7904e5054 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1324,12 +1324,18 @@ static irqreturn_t sh_eth_interrupt(int irq, void *netdev) struct sh_eth_private *mdp = netdev_priv(ndev); struct sh_eth_cpu_data *cd = mdp->cd; irqreturn_t ret = IRQ_NONE; - u32 intr_status = 0; + unsigned long intr_status; spin_lock(&mdp->lock); - /* Get interrpt stat */ + /* Get interrupt status */ intr_status = sh_eth_read(ndev, EESR); + /* Mask it with the interrupt mask, forcing ECI interrupt to be always + * enabled since it's the one that comes thru regardless of the mask, + * and we need to fully handle it in sh_eth_error() in order to quench + * it as it doesn't get cleared by just writing 1 to the ECI bit... + */ + intr_status &= sh_eth_read(ndev, EESIPR) | DMAC_M_ECI; /* Clear interrupt */ if (intr_status & (EESR_FRC | EESR_RMAF | EESR_RRF | EESR_RTLF | EESR_RTSF | EESR_PRE | EESR_CERF | -- cgit v1.2.3-58-ga151 From 3340d2aae3433ad9147f6bf0adc452b324e31591 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Sun, 31 Mar 2013 10:11:04 +0000 Subject: sh_eth: make 'link' field of 'struct sh_eth_private' *int* The 'link' field of 'struct sh_eth_private' has type 'enum phy_state' while the 'link' field of 'struct phy_device' is merely *int* (having values 0 and 1) and the former field gets assigned from the latter. Make the field match, getting rid of incorrectly used PHY_DOWN value in assignments/comparisons. Signed-off-by: Sergei Shtylyov Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 8 ++++---- drivers/net/ethernet/renesas/sh_eth.h | 2 +- 2 files changed, 5 insertions(+), 5 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 44f7904e5054..6ed333fe5c04 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1377,7 +1377,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) struct phy_device *phydev = mdp->phydev; int new_state = 0; - if (phydev->link != PHY_DOWN) { + if (phydev->link) { if (phydev->duplex != mdp->duplex) { new_state = 1; mdp->duplex = phydev->duplex; @@ -1391,7 +1391,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) if (mdp->cd->set_rate) mdp->cd->set_rate(ndev); } - if (mdp->link == PHY_DOWN) { + if (!mdp->link) { sh_eth_write(ndev, (sh_eth_read(ndev, ECMR) & ~ECMR_TXF), ECMR); new_state = 1; @@ -1401,7 +1401,7 @@ static void sh_eth_adjust_link(struct net_device *ndev) } } else if (mdp->link) { new_state = 1; - mdp->link = PHY_DOWN; + mdp->link = 0; mdp->speed = 0; mdp->duplex = -1; if (mdp->cd->no_psr || mdp->no_ether_link) @@ -1422,7 +1422,7 @@ static int sh_eth_phy_init(struct net_device *ndev) snprintf(phy_id, sizeof(phy_id), PHY_ID_FMT, mdp->mii_bus->id , mdp->phy_id); - mdp->link = PHY_DOWN; + mdp->link = 0; mdp->speed = 0; mdp->duplex = -1; diff --git a/drivers/net/ethernet/renesas/sh_eth.h b/drivers/net/ethernet/renesas/sh_eth.h index e6655678458e..828be4515008 100644 --- a/drivers/net/ethernet/renesas/sh_eth.h +++ b/drivers/net/ethernet/renesas/sh_eth.h @@ -723,7 +723,7 @@ struct sh_eth_private { u32 phy_id; /* PHY ID */ struct mii_bus *mii_bus; /* MDIO bus control */ struct phy_device *phydev; /* PHY device control */ - enum phy_state link; + int link; phy_interface_t phy_interface; int msg_enable; int speed; -- cgit v1.2.3-58-ga151 From 6741f40d198c6a5feb23653a1efd4ca47f93d83d Mon Sep 17 00:00:00 2001 From: Joseph CHANG Date: Thu, 28 Mar 2013 23:13:42 +0000 Subject: DM9000B: driver initialization upgrade Fix bug for DM9000 revision B which contain a DSP PHY DM9000B use DSP PHY instead previouse DM9000 revisions' analog PHY, So need extra change in initialization, For explicity PHY Reset and PHY init parameter, and first DM9000_NCR reset need NCR_MAC_LBK bit by dm9000_probe(). Following DM9000_NCR reset cause by dm9000_open() clear the NCR_MAC_LBK bit. Without this fix, Power-up FIFO pointers error happen around 2% rate among Davicom's customers' boards. With this fix, All above cases can be solved. Signed-off-by: Joseph CHANG Signed-off-by: David S. Miller --- drivers/net/ethernet/davicom/dm9000.c | 214 +++++++++++++++++----------------- drivers/net/ethernet/davicom/dm9000.h | 11 +- 2 files changed, 120 insertions(+), 105 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/davicom/dm9000.c b/drivers/net/ethernet/davicom/dm9000.c index 8cdf02503d13..9eada8e86078 100644 --- a/drivers/net/ethernet/davicom/dm9000.c +++ b/drivers/net/ethernet/davicom/dm9000.c @@ -257,6 +257,107 @@ static void dm9000_dumpblk_32bit(void __iomem *reg, int count) tmp = readl(reg); } +/* + * Sleep, either by using msleep() or if we are suspending, then + * use mdelay() to sleep. + */ +static void dm9000_msleep(board_info_t *db, unsigned int ms) +{ + if (db->in_suspend) + mdelay(ms); + else + msleep(ms); +} + +/* Read a word from phyxcer */ +static int +dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg) +{ + board_info_t *db = netdev_priv(dev); + unsigned long flags; + unsigned int reg_save; + int ret; + + mutex_lock(&db->addr_lock); + + spin_lock_irqsave(&db->lock, flags); + + /* Save previous register address */ + reg_save = readb(db->io_addr); + + /* Fill the phyxcer register into REG_0C */ + iow(db, DM9000_EPAR, DM9000_PHY | reg); + + /* Issue phyxcer read command */ + iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS); + + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + dm9000_msleep(db, 1); /* Wait read complete */ + + spin_lock_irqsave(&db->lock, flags); + reg_save = readb(db->io_addr); + + iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer read command */ + + /* The read data keeps on REG_0D & REG_0E */ + ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL); + + /* restore the previous address */ + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + mutex_unlock(&db->addr_lock); + + dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret); + return ret; +} + +/* Write a word to phyxcer */ +static void +dm9000_phy_write(struct net_device *dev, + int phyaddr_unused, int reg, int value) +{ + board_info_t *db = netdev_priv(dev); + unsigned long flags; + unsigned long reg_save; + + dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value); + mutex_lock(&db->addr_lock); + + spin_lock_irqsave(&db->lock, flags); + + /* Save previous register address */ + reg_save = readb(db->io_addr); + + /* Fill the phyxcer register into REG_0C */ + iow(db, DM9000_EPAR, DM9000_PHY | reg); + + /* Fill the written data into REG_0D & REG_0E */ + iow(db, DM9000_EPDRL, value); + iow(db, DM9000_EPDRH, value >> 8); + + /* Issue phyxcer write command */ + iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW); + + writeb(reg_save, db->io_addr); + spin_unlock_irqrestore(&db->lock, flags); + + dm9000_msleep(db, 1); /* Wait write complete */ + + spin_lock_irqsave(&db->lock, flags); + reg_save = readb(db->io_addr); + + iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer write command */ + + /* restore the previous address */ + writeb(reg_save, db->io_addr); + + spin_unlock_irqrestore(&db->lock, flags); + mutex_unlock(&db->addr_lock); +} + /* dm9000_set_io * * select the specified set of io routines to use with the @@ -795,6 +896,9 @@ dm9000_init_dm9000(struct net_device *dev) iow(db, DM9000_GPCR, GPCR_GEP_CNTL); /* Let GPIO0 output */ + dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET); /* PHY RESET */ + dm9000_phy_write(dev, 0, MII_DM_DSPCR, DSPCR_INIT_PARAM); /* Init */ + ncr = (db->flags & DM9000_PLATF_EXT_PHY) ? NCR_EXT_PHY : 0; /* if wol is needed, then always set NCR_WAKEEN otherwise we end @@ -1201,109 +1305,6 @@ dm9000_open(struct net_device *dev) return 0; } -/* - * Sleep, either by using msleep() or if we are suspending, then - * use mdelay() to sleep. - */ -static void dm9000_msleep(board_info_t *db, unsigned int ms) -{ - if (db->in_suspend) - mdelay(ms); - else - msleep(ms); -} - -/* - * Read a word from phyxcer - */ -static int -dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg) -{ - board_info_t *db = netdev_priv(dev); - unsigned long flags; - unsigned int reg_save; - int ret; - - mutex_lock(&db->addr_lock); - - spin_lock_irqsave(&db->lock,flags); - - /* Save previous register address */ - reg_save = readb(db->io_addr); - - /* Fill the phyxcer register into REG_0C */ - iow(db, DM9000_EPAR, DM9000_PHY | reg); - - iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS); /* Issue phyxcer read command */ - - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock,flags); - - dm9000_msleep(db, 1); /* Wait read complete */ - - spin_lock_irqsave(&db->lock,flags); - reg_save = readb(db->io_addr); - - iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer read command */ - - /* The read data keeps on REG_0D & REG_0E */ - ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL); - - /* restore the previous address */ - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock,flags); - - mutex_unlock(&db->addr_lock); - - dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret); - return ret; -} - -/* - * Write a word to phyxcer - */ -static void -dm9000_phy_write(struct net_device *dev, - int phyaddr_unused, int reg, int value) -{ - board_info_t *db = netdev_priv(dev); - unsigned long flags; - unsigned long reg_save; - - dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value); - mutex_lock(&db->addr_lock); - - spin_lock_irqsave(&db->lock,flags); - - /* Save previous register address */ - reg_save = readb(db->io_addr); - - /* Fill the phyxcer register into REG_0C */ - iow(db, DM9000_EPAR, DM9000_PHY | reg); - - /* Fill the written data into REG_0D & REG_0E */ - iow(db, DM9000_EPDRL, value); - iow(db, DM9000_EPDRH, value >> 8); - - iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW); /* Issue phyxcer write command */ - - writeb(reg_save, db->io_addr); - spin_unlock_irqrestore(&db->lock, flags); - - dm9000_msleep(db, 1); /* Wait write complete */ - - spin_lock_irqsave(&db->lock,flags); - reg_save = readb(db->io_addr); - - iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer write command */ - - /* restore the previous address */ - writeb(reg_save, db->io_addr); - - spin_unlock_irqrestore(&db->lock, flags); - mutex_unlock(&db->addr_lock); -} - static void dm9000_shutdown(struct net_device *dev) { @@ -1502,7 +1503,12 @@ dm9000_probe(struct platform_device *pdev) db->flags |= DM9000_PLATF_SIMPLE_PHY; #endif - dm9000_reset(db); + /* Fixing bug on dm9000_probe, takeover dm9000_reset(db), + * Need 'NCR_MAC_LBK' bit to indeed stable our DM9000 fifo + * while probe stage. + */ + + iow(db, DM9000_NCR, NCR_MAC_LBK | NCR_RST); /* try multiple times, DM9000 sometimes gets the read wrong */ for (i = 0; i < 8; i++) { diff --git a/drivers/net/ethernet/davicom/dm9000.h b/drivers/net/ethernet/davicom/dm9000.h index 55688bd1a3ef..9ce058adabab 100644 --- a/drivers/net/ethernet/davicom/dm9000.h +++ b/drivers/net/ethernet/davicom/dm9000.h @@ -69,7 +69,9 @@ #define NCR_WAKEEN (1<<6) #define NCR_FCOL (1<<4) #define NCR_FDX (1<<3) -#define NCR_LBK (3<<1) + +#define NCR_RESERVED (3<<1) +#define NCR_MAC_LBK (1<<1) #define NCR_RST (1<<0) #define NSR_SPEED (1<<7) @@ -167,5 +169,12 @@ #define ISR_LNKCHNG (1<<5) #define ISR_UNDERRUN (1<<4) +/* Davicom MII registers. + */ + +#define MII_DM_DSPCR 0x1b /* DSP Control Register */ + +#define DSPCR_INIT_PARAM 0xE100 /* DSP init parameter */ + #endif /* _DM9000X_H_ */ -- cgit v1.2.3-58-ga151 From 901ceba4e81e9dd6b4a3c4c37ee22000a6c5c65f Mon Sep 17 00:00:00 2001 From: Stone Piao Date: Fri, 29 Mar 2013 19:21:21 -0700 Subject: mwifiex: limit channel number not to overflow memory Limit the channel number in scan request, or the driver scan config structure memory will be overflowed. Cc: # 3.5+ Signed-off-by: Stone Piao Signed-off-by: Bing Zhao Signed-off-by: John W. Linville --- drivers/net/wireless/mwifiex/cfg80211.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/wireless/mwifiex/cfg80211.c b/drivers/net/wireless/mwifiex/cfg80211.c index a44023a7bd57..8aaf56ade4d9 100644 --- a/drivers/net/wireless/mwifiex/cfg80211.c +++ b/drivers/net/wireless/mwifiex/cfg80211.c @@ -1892,7 +1892,8 @@ mwifiex_cfg80211_scan(struct wiphy *wiphy, } } - for (i = 0; i < request->n_channels; i++) { + for (i = 0; i < min_t(u32, request->n_channels, + MWIFIEX_USER_SCAN_CHAN_MAX); i++) { chan = request->channels[i]; priv->user_scan_cfg->chan_list[i].chan_number = chan->hw_value; priv->user_scan_cfg->chan_list[i].radio_type = chan->band; -- cgit v1.2.3-58-ga151 From fcd99434fb5c137274d2e15dd2a6a7455f0f29ff Mon Sep 17 00:00:00 2001 From: Veaceslav Falico Date: Tue, 2 Apr 2013 05:15:16 +0000 Subject: bonding: get netdev_rx_handler_unregister out of locks Now that netdev_rx_handler_unregister contains synchronize_net(), we need to call it outside of bond->lock, cause it might sleep. Also, remove the already unneded synchronize_net(). Signed-off-by: Veaceslav Falico Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index 6bbd90e1123c..a51241b2e621 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -1976,12 +1976,11 @@ static int __bond_release_one(struct net_device *bond_dev, return -EINVAL; } + write_unlock_bh(&bond->lock); /* unregister rx_handler early so bond_handle_frame wouldn't be called * for this slave anymore. */ netdev_rx_handler_unregister(slave_dev); - write_unlock_bh(&bond->lock); - synchronize_net(); write_lock_bh(&bond->lock); if (!all && !bond->params.fail_over_mac) { -- cgit v1.2.3-58-ga151 From bab6a9eac05360db25c81b0090f6b1195dd986cc Mon Sep 17 00:00:00 2001 From: Yan Burman Date: Tue, 2 Apr 2013 16:49:45 +0300 Subject: net/mlx4_en: Fix setting initial MAC address Commit 6bbb6d9 "net/mlx4_en: Optimize Rx fast path filter checks" introduced a regression under which the MAC address read from the card was not converted correctly (the most significant byte was not handled), fix that. Reviewed-by: Or Gerlitz Signed-off-by: Yan Burman Signed-off-by: David S. Miller --- drivers/net/ethernet/mellanox/mlx4/en_netdev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c index f278b10ef714..30d78f806dc3 100644 --- a/drivers/net/ethernet/mellanox/mlx4/en_netdev.c +++ b/drivers/net/ethernet/mellanox/mlx4/en_netdev.c @@ -411,8 +411,8 @@ static int mlx4_en_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid) static void mlx4_en_u64_to_mac(unsigned char dst_mac[ETH_ALEN + 2], u64 src_mac) { - unsigned int i; - for (i = ETH_ALEN - 1; i; --i) { + int i; + for (i = ETH_ALEN - 1; i >= 0; --i) { dst_mac[i] = src_mac & 0xff; src_mac >>= 8; } -- cgit v1.2.3-58-ga151 From e2409d83434d77874b461b78af6a19cd6e6a1280 Mon Sep 17 00:00:00 2001 From: hayeswang Date: Sun, 31 Mar 2013 17:02:04 +0000 Subject: r8169: fix auto speed down issue It would cause no link after suspending or shutdowning when the nic changes the speed to 10M and connects to a link partner which forces the speed to 100M. Check the link partner ability to determine which speed to set. Signed-off-by: Hayes Wang Acked-by: Francois Romieu Signed-off-by: David S. Miller --- drivers/net/ethernet/realtek/r8169.c | 28 +++++++++++++++++++++++++--- 1 file changed, 25 insertions(+), 3 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/realtek/r8169.c b/drivers/net/ethernet/realtek/r8169.c index 28fb50a1e9c3..4ecbe64a758d 100644 --- a/drivers/net/ethernet/realtek/r8169.c +++ b/drivers/net/ethernet/realtek/r8169.c @@ -3818,6 +3818,30 @@ static void rtl_init_mdio_ops(struct rtl8169_private *tp) } } +static void rtl_speed_down(struct rtl8169_private *tp) +{ + u32 adv; + int lpa; + + rtl_writephy(tp, 0x1f, 0x0000); + lpa = rtl_readphy(tp, MII_LPA); + + if (lpa & (LPA_10HALF | LPA_10FULL)) + adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full; + else if (lpa & (LPA_100HALF | LPA_100FULL)) + adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full | + ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full; + else + adv = ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full | + ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full | + (tp->mii.supports_gmii ? + ADVERTISED_1000baseT_Half | + ADVERTISED_1000baseT_Full : 0); + + rtl8169_set_speed(tp->dev, AUTONEG_ENABLE, SPEED_1000, DUPLEX_FULL, + adv); +} + static void rtl_wol_suspend_quirk(struct rtl8169_private *tp) { void __iomem *ioaddr = tp->mmio_addr; @@ -3848,9 +3872,7 @@ static bool rtl_wol_pll_power_down(struct rtl8169_private *tp) if (!(__rtl8169_get_wol(tp) & WAKE_ANY)) return false; - rtl_writephy(tp, 0x1f, 0x0000); - rtl_writephy(tp, MII_BMCR, 0x0000); - + rtl_speed_down(tp); rtl_wol_suspend_quirk(tp); return true; -- cgit v1.2.3-58-ga151 From 31d1670e73f4911fe401273a8f576edc9c2b5fea Mon Sep 17 00:00:00 2001 From: Hannes Frederic Sowa Date: Tue, 2 Apr 2013 14:36:46 +0000 Subject: atl1e: limit gso segment size to prevent generation of wrong ip length fields The limit of 0x3c00 is taken from the windows driver. Suggested-by: Huang, Xiong Cc: Huang, Xiong Cc: Eric Dumazet Signed-off-by: Hannes Frederic Sowa Signed-off-by: David S. Miller --- drivers/net/ethernet/atheros/atl1e/atl1e.h | 2 +- drivers/net/ethernet/atheros/atl1e/atl1e_main.c | 1 + 2 files changed, 2 insertions(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e.h b/drivers/net/ethernet/atheros/atl1e/atl1e.h index edfdf6b950e7..b5fd934585e9 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e.h +++ b/drivers/net/ethernet/atheros/atl1e/atl1e.h @@ -186,7 +186,7 @@ struct atl1e_tpd_desc { /* how about 0x2000 */ #define MAX_TX_BUF_LEN 0x2000 #define MAX_TX_BUF_SHIFT 13 -/*#define MAX_TX_BUF_LEN 0x3000 */ +#define MAX_TSO_SEG_SIZE 0x3c00 /* rrs word 1 bit 0:31 */ #define RRS_RX_CSUM_MASK 0xFFFF diff --git a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c index f73d5609439a..ac25f05ff68f 100644 --- a/drivers/net/ethernet/atheros/atl1e/atl1e_main.c +++ b/drivers/net/ethernet/atheros/atl1e/atl1e_main.c @@ -2329,6 +2329,7 @@ static int atl1e_probe(struct pci_dev *pdev, const struct pci_device_id *ent) INIT_WORK(&adapter->reset_task, atl1e_reset_task); INIT_WORK(&adapter->link_chg_task, atl1e_link_chg_task); + netif_set_gso_max_size(netdev, MAX_TSO_SEG_SIZE); err = register_netdev(netdev); if (err) { netdev_err(netdev, "register netdevice failed\n"); -- cgit v1.2.3-58-ga151 From 4de79c737b200492195ebc54a887075327e1ec1d Mon Sep 17 00:00:00 2001 From: Veaceslav Falico Date: Wed, 3 Apr 2013 05:46:33 +0000 Subject: bonding: remove sysfs before removing devices We have a race condition if we try to rmmod bonding and simultaneously add a bond master through sysfs. In bonding_exit() we first remove the devices (through rtnl_link_unregister() ) and only after that we remove the sysfs. If we manage to add a device through sysfs after that the devices were removed - we'll end up with that device/sysfs structure and with the module unloaded. Fix this by first removing the sysfs and only after that calling rtnl_link_unregister(). Signed-off-by: Veaceslav Falico Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'drivers/net') diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index a51241b2e621..171b10f167a5 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -4902,8 +4902,8 @@ static void __exit bonding_exit(void) bond_destroy_debugfs(); - rtnl_link_unregister(&bond_link_ops); unregister_pernet_subsys(&bond_net_ops); + rtnl_link_unregister(&bond_link_ops); #ifdef CONFIG_NET_POLL_CONTROLLER /* -- cgit v1.2.3-58-ga151 From f01fc1a82c2ee68726b400fadb156bd623b5f2f1 Mon Sep 17 00:00:00 2001 From: Jakub Kicinski Date: Wed, 3 Apr 2013 16:50:54 +0000 Subject: ixgbe: fix registration order of driver and DCA nofitication ixgbe_notify_dca cannot be called before driver registration because it expects driver's klist_devices to be allocated and initialized. While on it make sure debugfs files are removed when registration fails. Cc: stable Signed-off-by: Jakub Kicinski Tested-by: Phil Schmitt Signed-off-by: Jeff Kirsher Signed-off-by: David S. Miller --- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 11 +++++++++-- 1 file changed, 9 insertions(+), 2 deletions(-) (limited to 'drivers/net') diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index db5611ae407e..79f4a26ea6cc 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -7922,12 +7922,19 @@ static int __init ixgbe_init_module(void) ixgbe_dbg_init(); #endif /* CONFIG_DEBUG_FS */ + ret = pci_register_driver(&ixgbe_driver); + if (ret) { +#ifdef CONFIG_DEBUG_FS + ixgbe_dbg_exit(); +#endif /* CONFIG_DEBUG_FS */ + return ret; + } + #ifdef CONFIG_IXGBE_DCA dca_register_notify(&dca_notifier); #endif - ret = pci_register_driver(&ixgbe_driver); - return ret; + return 0; } module_init(ixgbe_init_module); -- cgit v1.2.3-58-ga151