From adf5b4dcc0cf50715f74f49f3c7af0c80467f55f Mon Sep 17 00:00:00 2001 From: Stefan Herbrechtsmeier Date: Tue, 15 Jul 2014 12:02:35 +0200 Subject: ARM: dts: set 'ti,set-rate-parent' for dpll4_m5x2 clock Set 'ti,set-rate-parent' property for the dpll4_m5x2_ck clock, which is used for the ISP functional clock. This fixes the OMAP3 ISP driver's clock rate configuration on OMAP34xx, which needs the rate to be propagated properly to the divider node (dpll4_m5_ck). Signed-off-by: Stefan Herbrechtsmeier Cc: Laurent Pinchart Cc: Tony Lindgren Cc: Tero Kristo Cc: Cc: Acked-by: Laurent Pinchart Signed-off-by: Tero Kristo --- arch/arm/boot/dts/omap3xxx-clocks.dtsi | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/omap3xxx-clocks.dtsi b/arch/arm/boot/dts/omap3xxx-clocks.dtsi index e47ff69dcf70..5c375003bad1 100644 --- a/arch/arm/boot/dts/omap3xxx-clocks.dtsi +++ b/arch/arm/boot/dts/omap3xxx-clocks.dtsi @@ -467,6 +467,7 @@ ti,bit-shift = <0x1e>; reg = <0x0d00>; ti,set-bit-to-disable; + ti,set-rate-parent; }; dpll4_m6_ck: dpll4_m6_ck { -- cgit v1.2.3-58-ga151 From 929a015b1809a30748d487f9d25b16a41434b61a Mon Sep 17 00:00:00 2001 From: Peter Ujfalusi Date: Mon, 4 Aug 2014 15:26:56 +0300 Subject: ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC The edma_setup_from_hw() should know about the CC number when parsing the CCCFG register - when it reads the register to be precise. The base addresses for CCs stored in an array and we need to provide the correct id to edma_read() in order to read the correct register. Cc: # 3.16 Signed-off-by: Peter Ujfalusi Signed-off-by: Sekhar Nori --- arch/arm/common/edma.c | 9 +++++---- 1 file changed, 5 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/common/edma.c b/arch/arm/common/edma.c index 88099175fc56..d86771abbf57 100644 --- a/arch/arm/common/edma.c +++ b/arch/arm/common/edma.c @@ -1443,14 +1443,14 @@ void edma_assign_channel_eventq(unsigned channel, enum dma_event_q eventq_no) EXPORT_SYMBOL(edma_assign_channel_eventq); static int edma_setup_from_hw(struct device *dev, struct edma_soc_info *pdata, - struct edma *edma_cc) + struct edma *edma_cc, int cc_id) { int i; u32 value, cccfg; s8 (*queue_priority_map)[2]; /* Decode the eDMA3 configuration from CCCFG register */ - cccfg = edma_read(0, EDMA_CCCFG); + cccfg = edma_read(cc_id, EDMA_CCCFG); value = GET_NUM_REGN(cccfg); edma_cc->num_region = BIT(value); @@ -1464,7 +1464,8 @@ static int edma_setup_from_hw(struct device *dev, struct edma_soc_info *pdata, value = GET_NUM_EVQUE(cccfg); edma_cc->num_tc = value + 1; - dev_dbg(dev, "eDMA3 HW configuration (cccfg: 0x%08x):\n", cccfg); + dev_dbg(dev, "eDMA3 CC%d HW configuration (cccfg: 0x%08x):\n", cc_id, + cccfg); dev_dbg(dev, "num_region: %u\n", edma_cc->num_region); dev_dbg(dev, "num_channel: %u\n", edma_cc->num_channels); dev_dbg(dev, "num_slot: %u\n", edma_cc->num_slots); @@ -1684,7 +1685,7 @@ static int edma_probe(struct platform_device *pdev) return -ENOMEM; /* Get eDMA3 configuration from IP */ - ret = edma_setup_from_hw(dev, info[j], edma_cc[j]); + ret = edma_setup_from_hw(dev, info[j], edma_cc[j], j); if (ret) return ret; -- cgit v1.2.3-58-ga151 From dbd366fdf2650531045ce47833b1efcdeec4dd86 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Tue, 2 Sep 2014 14:41:21 +0200 Subject: ARM: ux500: disable msp2 node on Snowball Analogous to commit 8858d88a25142544843869f0cd3e6654aa7b4aec that fixed commit 70b41abc151f9 "ARM: ux500: move MSP pin control to the device tree" accidentally activated MSP2, giving rise to a boot scroll scream as the kernel attempts to probe a driver for it and fails to obtain DMA channel 14. For some reason I forgot to fix this on the Snowball. Fix this up by marking the node disabled again. Cc: Lee Jones Signed-off-by: Linus Walleij Tested-by: Kevin Hilman Signed-off-by: Kevin Hilman --- arch/arm/boot/dts/ste-snowball.dts | 1 - 1 file changed, 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index 4a2000c620ad..3e97a669f15e 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -116,7 +116,6 @@ msp2: msp@80117000 { pinctrl-names = "default"; pinctrl-0 = <&msp2_default_mode>; - status = "okay"; }; msp3: msp@80125000 { -- cgit v1.2.3-58-ga151 From 544d63d0f34e13fc7e7ca909800526809b194eb9 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 3 Sep 2014 14:17:31 +0300 Subject: ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency The I2C3 pins are taken from pads E21 (GPIO6_14) and F20 (GPIO6_15). Use the right pinmux register and mode. Also set the I2C3 bus frequency to a safer 400KHz than 3.4Mhz. CC: Peter Ujfalusi Signed-off-by: Roger Quadros Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7-evm.dts | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 50f8022905a1..42f5bc9941c7 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -43,8 +43,8 @@ i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0x410 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */ - 0x414 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */ + 0x288 (PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */ + 0x28c (PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */ >; }; @@ -284,7 +284,7 @@ status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c3_pins>; - clock-frequency = <3400000>; + clock-frequency = <400000>; }; &mcspi1 { -- cgit v1.2.3-58-ga151 From f0e9fab3bcb526a45ecbae7ef7e4ceec7852cba4 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Wed, 3 Sep 2014 14:17:32 +0300 Subject: ARM: dts: dra7-evm: Fix 8th NAND partition's name The 8th NAND partition should be named "NAND.u-boot-env.backup1" instead of "NAND.u-boot-env". This is to be consistent with other TI boards as well as u-boot. CC: Pekon Gupta Signed-off-by: Roger Quadros Signed-off-by: Sekhar Nori Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 42f5bc9941c7..990ee6afc4f0 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -483,7 +483,7 @@ reg = <0x001c0000 0x00020000>; }; partition@7 { - label = "NAND.u-boot-env"; + label = "NAND.u-boot-env.backup1"; reg = <0x001e0000 0x00020000>; }; partition@8 { -- cgit v1.2.3-58-ga151 From 93166413305b714e356a3fa76f2d98791fa425c2 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Wed, 3 Sep 2014 13:46:21 -0500 Subject: ARM: dts: am437x-gp: switch i2c0 to 100KHz On the GP EVM, the ambient light sensor is limited to 100KHz on the I2C bus. So use 100kHz for I2C on the GP EVM due to this limitation on the ambient light sensor. Reported-by: Aparna Balasubramanian Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-gp-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index 646a6eade788..9559c1962ac8 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -260,7 +260,7 @@ status = "okay"; pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins>; - clock-frequency = <400000>; + clock-frequency = <100000>; tps65218: tps65218@24 { reg = <0x24>; -- cgit v1.2.3-58-ga151 From 4b143f0f60143a8238262874c1ee22b43fbdc61e Mon Sep 17 00:00:00 2001 From: Felipe Balbi Date: Wed, 3 Sep 2014 16:22:24 -0500 Subject: ARM: dts: am4372: fix USB regs size Size should be 64KiB instead of 92KiB. Signed-off-by: Felipe Balbi Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am4372.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index 9b3d2ba82f13..8689949bdba3 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -804,7 +804,7 @@ usb1: usb@48390000 { compatible = "synopsys,dwc3"; - reg = <0x48390000 0x17000>; + reg = <0x48390000 0x10000>; interrupts = ; phys = <&usb2_phy1>; phy-names = "usb2-phy"; @@ -826,7 +826,7 @@ usb2: usb@483d0000 { compatible = "synopsys,dwc3"; - reg = <0x483d0000 0x17000>; + reg = <0x483d0000 0x10000>; interrupts = ; phys = <&usb2_phy2>; phy-names = "usb2-phy"; -- cgit v1.2.3-58-ga151 From db01e6c7fbe3b87b389f537b52a5d862cea498e1 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 2 Sep 2014 16:57:02 +0300 Subject: ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8 am43x-epos-evm uses a NAND chip with page size 4096 bytes and spare area of 225 bytes per page. For such a setup it is preferrable to use BCH16 ECC scheme over BCH8. This also makes it compatible with ROM code ECC scheme so we can boot with NAND after flashing from kernel. Signed-off-by: Roger Quadros Reviewed-by: Pekon Gupta Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am43x-epos-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index ed7dd2395915..f6c98985b5c7 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -441,7 +441,7 @@ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ nand@0,0 { reg = <0 0 0>; /* CS0, offset 0 */ - ti,nand-ecc-opt = "bch8"; + ti,nand-ecc-opt = "bch16"; ti,elm-id = <&elm>; nand-bus-width = <8>; gpmc,device-width = <1>; -- cgit v1.2.3-58-ga151 From 6b8691100538427ad739fc8735451a30c73316ff Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 2 Sep 2014 16:57:03 +0300 Subject: ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8 am437x-gp-evm uses a NAND chip with page size 4096 bytes and spare area of 225 bytes per page. For such a setup it is preferrable to use BCH16 ECC scheme over BCH8. This also makes it compatible with ROM code ECC scheme so we can boot with NAND after flashing from kernel. Signed-off-by: Roger Quadros Reviewed-by: Pekon Gupta Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-gp-evm.dts | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index 9559c1962ac8..bd64159e6b32 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -424,7 +424,7 @@ ranges = <0 0 0 0x01000000>; /* minimum GPMC partition = 16MB */ nand@0,0 { reg = <0 0 4>; /* device IO registers */ - ti,nand-ecc-opt = "bch8"; + ti,nand-ecc-opt = "bch16"; ti,elm-id = <&elm>; nand-bus-width = <8>; gpmc,device-width = <1>; -- cgit v1.2.3-58-ga151 From 302946dee9542718ea347b70fbf3bc90081e00e9 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 2 Sep 2014 16:57:04 +0300 Subject: ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring NAND uses wait pin only to indicate device readiness after a block/page operation. It is not use to extend individual read/write cycle and so read/write wait pin monitoring must be disabled for NAND. This patch also gets rid of the below warning when NAND is accessed for the first time. omap_l3_noc 44000000.ocp: L3 application error: target 13 mod:1 (unclearable) Signed-off-by: Roger Quadros Reviewed-by: Pekon Gupta Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am437x-gp-evm.dts | 2 -- 1 file changed, 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts index bd64159e6b32..e7ac47fa6615 100644 --- a/arch/arm/boot/dts/am437x-gp-evm.dts +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -443,8 +443,6 @@ gpmc,rd-cycle-ns = <40>; gpmc,wr-cycle-ns = <40>; gpmc,wait-pin = <0>; - gpmc,wait-on-read; - gpmc,wait-on-write; gpmc,bus-turnaround-ns = <0>; gpmc,cycle2cycle-delay-ns = <0>; gpmc,clk-activation-ns = <0>; -- cgit v1.2.3-58-ga151 From e47acd9626ec8cc0292fd54e2bc50fae12cf4188 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 2 Sep 2014 16:57:05 +0300 Subject: ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring NAND uses wait pin only to indicate device readiness after a block/page operation. It is not use to extend individual read/write cycle and so read/write wait pin monitoring must be disabled for NAND. Add gpmc wait pin information as the NAND uses wait pin 0 for device ready indication. Signed-off-by: Roger Quadros Reviewed-by: Pekon Gupta Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am43x-epos-evm.dts | 3 +-- 1 file changed, 1 insertion(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index f6c98985b5c7..b489b278f184 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -459,8 +459,7 @@ gpmc,access-ns = <30>; /* tCEA + 4*/ gpmc,rd-cycle-ns = <40>; gpmc,wr-cycle-ns = <40>; - gpmc,wait-on-read = "true"; - gpmc,wait-on-write = "true"; + gpmc,wait-pin = <0>; gpmc,bus-turnaround-ns = <0>; gpmc,cycle2cycle-delay-ns = <0>; gpmc,clk-activation-ns = <0>; -- cgit v1.2.3-58-ga151 From 2b54057c9b2638792bdd83b58bad7a0cdf5f4533 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 2 Sep 2014 16:57:06 +0300 Subject: ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring For NAND read & write wait pin monitoring must be kept disabled as the wait pin is only used to indicate NAND device ready status and not to extend each read/write cycle. So don't print a warning if wait pin is specified while read/write monitoring is not in the device tree. Sanity check wait pin number irrespective if read/write monitoring is set or not. Signed-off-by: Roger Quadros Reviewed-by: Pekon Gupta Signed-off-by: Tony Lindgren --- arch/arm/mach-omap2/gpmc.c | 7 +++---- 1 file changed, 3 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/mach-omap2/gpmc.c b/arch/arm/mach-omap2/gpmc.c index 9f42d5437fcc..2f97228f188a 100644 --- a/arch/arm/mach-omap2/gpmc.c +++ b/arch/arm/mach-omap2/gpmc.c @@ -1207,8 +1207,7 @@ int gpmc_cs_program_settings(int cs, struct gpmc_settings *p) } } - if ((p->wait_on_read || p->wait_on_write) && - (p->wait_pin > gpmc_nr_waitpins)) { + if (p->wait_pin > gpmc_nr_waitpins) { pr_err("%s: invalid wait-pin (%d)\n", __func__, p->wait_pin); return -EINVAL; } @@ -1288,8 +1287,8 @@ void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p) p->wait_on_write = of_property_read_bool(np, "gpmc,wait-on-write"); if (!p->wait_on_read && !p->wait_on_write) - pr_warn("%s: read/write wait monitoring not enabled!\n", - __func__); + pr_debug("%s: rd/wr wait monitoring not enabled!\n", + __func__); } } -- cgit v1.2.3-58-ga151 From 331bbb595ef93b68272e011f8ac81b260e672db5 Mon Sep 17 00:00:00 2001 From: Roger Quadros Date: Tue, 2 Sep 2014 16:57:07 +0300 Subject: ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND Both QSPI and GPMC-NAND share the same Pin (A8) from the SoC for Chip Select functionality. So both can't be enabled simultaneously. Disable QSPI node to prevent the pin conflict as well as be similar to 3.12 release. CC: Sourav Poddar Signed-off-by: Roger Quadros Reviewed-by: Pekon Gupta Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/am43x-epos-evm.dts | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index b489b278f184..ac3e4859935f 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -435,7 +435,7 @@ }; &gpmc { - status = "okay"; + status = "okay"; /* Disable QSPI when enabling GPMC (NAND) */ pinctrl-names = "default"; pinctrl-0 = <&nand_flash_x8>; ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ @@ -556,7 +556,7 @@ }; &qspi { - status = "okay"; + status = "disabled"; /* Disable GPMC (NAND) when enabling QSPI */ pinctrl-names = "default"; pinctrl-0 = <&qspi1_default>; -- cgit v1.2.3-58-ga151 From 68e4d9e58dbae2fb178e8b74806f521adb16f0d3 Mon Sep 17 00:00:00 2001 From: Nishanth Menon Date: Thu, 4 Sep 2014 08:33:37 -0500 Subject: ARM: dts: dra7-evm: Fix spi1 mux documentation While auditing the various pin ctrl configurations using the following command: grep PIN_ arch/arm/boot/dts/dra7-evm.dts|(while read line; do v=`echo "$line" | sed -e "s/\s\s*/|/g" | cut -d '|' -f1 | cut -d 'x' -f2|tr [a-z] [A-Z]`; HEX=`echo "obase=16;ibase=16;4A003400+$v"| bc`; echo "$HEX ===> $line"; done) against DRA75x/74x NDA TRM revision S(SPRUHI2S August 2014), documentation errors were found for spi1 pinctrl. Fix the same. Fixes: 6e58b8f1daaf1af ("ARM: dts: DRA7: Add the dts files for dra7 SoC and dra7-evm board") Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7-evm.dts | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index 990ee6afc4f0..b80c67b6fe01 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -50,13 +50,13 @@ mcspi1_pins: pinmux_mcspi1_pins { pinctrl-single,pins = < - 0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */ - 0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */ - 0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */ - 0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */ - 0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */ - 0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */ - 0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */ + 0x3a4 (PIN_INPUT | MUX_MODE0) /* spi1_sclk */ + 0x3a8 (PIN_INPUT | MUX_MODE0) /* spi1_d1 */ + 0x3ac (PIN_INPUT | MUX_MODE0) /* spi1_d0 */ + 0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */ + 0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs1 */ + 0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */ + 0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */ >; }; -- cgit v1.2.3-58-ga151 From c7cc9ba11f8c09a4d12af0fc4aa9f9b026cdd354 Mon Sep 17 00:00:00 2001 From: Lokesh Vutla Date: Thu, 4 Sep 2014 08:23:28 -0500 Subject: ARM: dts: dra7-evm: Add vtt regulator support DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination and this is controlled by gpio7_11. This gpio is configured in boot loader. gpio7_11, which is only available only on Pad A22, in previous boards, is connected only to an unused pad on expansion connector EXP_P3 and is safe to be muxed as GPIO on all DRA7-evm versions (without a need to spin off another dts file). Since gpio7_11 is used to control VTT and should not be reset or kept in idle state during boot up else VTT will be disconnected and DDR gets corrupted. So, as part of this change, mark gpio7 as no-reset and no-idle on init. Signed-off-by: Lokesh Vutla Signed-off-by: Nishanth Menon Signed-off-by: Tony Lindgren --- arch/arm/boot/dts/dra7-evm.dts | 27 ++++++++++++++++++++++++++- 1 file changed, 26 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts index b80c67b6fe01..e03fbf3c6889 100644 --- a/arch/arm/boot/dts/dra7-evm.dts +++ b/arch/arm/boot/dts/dra7-evm.dts @@ -8,6 +8,7 @@ /dts-v1/; #include "dra74x.dtsi" +#include / { model = "TI DRA742"; @@ -24,9 +25,29 @@ regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; }; + + vtt_fixed: fixedregulator-vtt { + compatible = "regulator-fixed"; + regulator-name = "vtt_fixed"; + regulator-min-microvolt = <1350000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + enable-active-high; + gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>; + }; }; &dra7_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = <&vtt_pin>; + + vtt_pin: pinmux_vtt_pin { + pinctrl-single,pins = < + 0x3b4 (PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */ + >; + }; + i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < 0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */ @@ -54,7 +75,6 @@ 0x3a8 (PIN_INPUT | MUX_MODE0) /* spi1_d1 */ 0x3ac (PIN_INPUT | MUX_MODE0) /* spi1_d0 */ 0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */ - 0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs1 */ 0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */ 0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */ >; @@ -504,3 +524,8 @@ &usb2_phy2 { phy-supply = <&ldousb_reg>; }; + +&gpio7 { + ti,no-reset-on-init; + ti,no-idle-on-init; +}; -- cgit v1.2.3-58-ga151 From 650ca015fd52b130af82518d5ed338f52974cec4 Mon Sep 17 00:00:00 2001 From: Gaël PORTAY Date: Mon, 1 Sep 2014 23:29:46 +0200 Subject: ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The at91sam9g20 SOC uses its own pllb implementation which is different from the one inherited from at91sam9260 SOC. Signed-off-by: Gaël PORTAY Acked-by: Boris Brezillon Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/at91sam9g20.dtsi | 1 + 1 file changed, 1 insertion(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/at91sam9g20.dtsi b/arch/arm/boot/dts/at91sam9g20.dtsi index 31f7652612fc..4e0abbd9d655 100644 --- a/arch/arm/boot/dts/at91sam9g20.dtsi +++ b/arch/arm/boot/dts/at91sam9g20.dtsi @@ -40,6 +40,7 @@ }; pllb: pllbck { + compatible = "atmel,at91sam9g20-clk-pllb"; atmel,clk-input-range = <2000000 32000000>; atmel,pll-clk-output-ranges = <30000000 100000000 0 0>; }; -- cgit v1.2.3-58-ga151 From 04ffc960d7295b7f05bf4a14e1f7d967e46b7577 Mon Sep 17 00:00:00 2001 From: Alexandre Belloni Date: Fri, 5 Sep 2014 16:15:33 +0200 Subject: ARM: at91: rm9200: fix clock registration Actually register clocks from device tree when using the common clock framework. Signed-off-by: Alexandre Belloni Acked-by: Boris Brezillon [nicolas.ferre@atmel.com: add at91 to function name] Signed-off-by: Nicolas Ferre --- arch/arm/mach-at91/board-dt-rm9200.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/mach-at91/board-dt-rm9200.c b/arch/arm/mach-at91/board-dt-rm9200.c index 3a185faee795..f4b6e91843e4 100644 --- a/arch/arm/mach-at91/board-dt-rm9200.c +++ b/arch/arm/mach-at91/board-dt-rm9200.c @@ -14,6 +14,7 @@ #include #include #include +#include #include #include @@ -35,13 +36,21 @@ static void __init at91rm9200_dt_init_irq(void) of_irq_init(irq_of_match); } +static void __init at91rm9200_dt_timer_init(void) +{ +#if defined(CONFIG_COMMON_CLK) + of_clk_init(NULL); +#endif + at91rm9200_timer_init(); +} + static const char *at91rm9200_dt_board_compat[] __initdata = { "atmel,at91rm9200", NULL }; DT_MACHINE_START(at91rm9200_dt, "Atmel AT91RM9200 (Device Tree)") - .init_time = at91rm9200_timer_init, + .init_time = at91rm9200_dt_timer_init, .map_io = at91_map_io, .handle_irq = at91_aic_handle_irq, .init_early = at91rm9200_dt_initialize, -- cgit v1.2.3-58-ga151 From ea4fc621adec8956944ecdb9a36c549cba8718c0 Mon Sep 17 00:00:00 2001 From: Alexandre Belloni Date: Fri, 5 Sep 2014 16:45:12 +0200 Subject: ARM: at91/dt: rm9200: fix usb clock definition The atmel,clk-divisors property is taking 4 divisors, if less are provided, the clock registration will fail. Signed-off-by: Alexandre Belloni Signed-off-by: Nicolas Ferre --- arch/arm/boot/dts/at91rm9200.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi index 65ccf564b9a5..6c97d4af61ee 100644 --- a/arch/arm/boot/dts/at91rm9200.dtsi +++ b/arch/arm/boot/dts/at91rm9200.dtsi @@ -149,7 +149,7 @@ usb: usbck { compatible = "atmel,at91rm9200-clk-usb"; #clock-cells = <0>; - atmel,clk-divisors = <1 2>; + atmel,clk-divisors = <1 2 0 0>; clocks = <&pllb>; }; -- cgit v1.2.3-58-ga151