From 4aa0f4d7264bc4f54603de5db1ffcaf8912ddd23 Mon Sep 17 00:00:00 2001 From: Phil Sutter Date: Fri, 28 Nov 2008 20:45:10 +0100 Subject: MIPS: RB532: Add set_type() function to IRQ struct. Interrupt Group 4 mapps the GPIO pins enabled as interrupt sources; add defines to make this clear when addressing them later in code. The mapped GPIOs support triggering on either level high or low. To achieve this, the set_type() function calls rb532_gpio_set_ilevel() for interrupts of the above mentioned group. As there is no way to alter the triggering characteristics of the other interrupts, accept level triggering on status high only. (This is just a guess; but as the system boots fine and interrupt-driven devices (e.g. serial console) work with no implications, it seems to be right.) To clear a GPIO mapped IRQ, the source has to be cleared (i.e., the interrupt status bit of the corresponding GPIO pin). This is done inside rb532_disable_irq(). After applying these changes I could undo most of my former "fixes" to pata-rb532-cf. Particularly all interrupt handling can be done generically via set_irq_type() as it was before. Signed-off-by: Phil Sutter Signed-off-by: Ralf Baechle --- arch/mips/include/asm/mach-rc32434/irq.h | 3 +++ arch/mips/rb532/irq.c | 27 +++++++++++++++++++++++++++ 2 files changed, 30 insertions(+) (limited to 'arch/mips') diff --git a/arch/mips/include/asm/mach-rc32434/irq.h b/arch/mips/include/asm/mach-rc32434/irq.h index 56738d8ec4e2..023a5b100ed0 100644 --- a/arch/mips/include/asm/mach-rc32434/irq.h +++ b/arch/mips/include/asm/mach-rc32434/irq.h @@ -30,4 +30,7 @@ #define ETH0_RX_OVR_IRQ (GROUP3_IRQ_BASE + 9) #define ETH0_TX_UND_IRQ (GROUP3_IRQ_BASE + 10) +#define GPIO_MAPPED_IRQ_BASE GROUP4_IRQ_BASE +#define GPIO_MAPPED_IRQ_GROUP 4 + #endif /* __ASM_RC32434_IRQ_H */ diff --git a/arch/mips/rb532/irq.c b/arch/mips/rb532/irq.c index 549b46d2fcee..53eeb5e7bc5b 100644 --- a/arch/mips/rb532/irq.c +++ b/arch/mips/rb532/irq.c @@ -46,6 +46,7 @@ #include #include +#include struct intr_group { u32 mask; /* mask of valid bits in pending/mask registers */ @@ -150,6 +151,9 @@ static void rb532_disable_irq(unsigned int irq_nr) mask |= intr_bit; WRITE_MASK(addr, mask); + if (group == GPIO_MAPPED_IRQ_GROUP) + rb532_gpio_set_istat(0, irq_nr - GPIO_MAPPED_IRQ_BASE); + /* * if there are no more interrupts enabled in this * group, disable corresponding IP @@ -165,12 +169,35 @@ static void rb532_mask_and_ack_irq(unsigned int irq_nr) ack_local_irq(group_to_ip(irq_to_group(irq_nr))); } +static int rb532_set_type(unsigned int irq_nr, unsigned type) +{ + int gpio = irq_nr - GPIO_MAPPED_IRQ_BASE; + int group = irq_to_group(irq_nr); + + if (group != GPIO_MAPPED_IRQ_GROUP) + return (type == IRQ_TYPE_LEVEL_HIGH) ? 0 : -EINVAL; + + switch (type) { + case IRQ_TYPE_LEVEL_HIGH: + rb532_gpio_set_ilevel(1, gpio); + break; + case IRQ_TYPE_LEVEL_LOW: + rb532_gpio_set_ilevel(0, gpio); + break; + default: + return -EINVAL; + } + + return 0; +} + static struct irq_chip rc32434_irq_type = { .name = "RB532", .ack = rb532_disable_irq, .mask = rb532_disable_irq, .mask_ack = rb532_mask_and_ack_irq, .unmask = rb532_enable_irq, + .set_type = rb532_set_type, }; void __init arch_init_irq(void) -- cgit v1.2.3-58-ga151