From 0a8727e69778683495058852f783eeda141a754e Mon Sep 17 00:00:00 2001 From: Thor Thayer Date: Thu, 6 Nov 2014 13:54:27 -0600 Subject: spi: dw: Fix dynamic speed change. An IOCTL call that calls spi_setup() and then dw_spi_setup() will overwrite the persisted last transfer speed. On each transfer, the SPI speed is compared to the last transfer speed to determine if the clock divider registers need to be updated (did the speed change?). This bug was observed with the spidev driver using spi-config to update the max transfer speed. This fix: Don't overwrite the persisted last transaction clock speed when updating the SPI parameters in dw_spi_setup(). On the next transaction, the new speed won't match the persisted last speed and the hardware registers will be updated. On initialization, the persisted last transaction clock speed will be 0 but will be updated after the first SPI transaction. Move zeroed clock divider check into clock change test because chip->clk_div is zero on startup and would cause a divide-by-zero error. The calculation was wrong as well (can't support odd #). Reported-by: Vlastimil Setka Signed-off-by: Vlastimil Setka Signed-off-by: Thor Thayer Signed-off-by: Mark Brown Cc: stable@vger.kernel.org --- drivers/spi/spi-dw.c | 6 +----- 1 file changed, 1 insertion(+), 5 deletions(-) diff --git a/drivers/spi/spi-dw.c b/drivers/spi/spi-dw.c index 729215885250..332a6abd8cf3 100644 --- a/drivers/spi/spi-dw.c +++ b/drivers/spi/spi-dw.c @@ -376,9 +376,6 @@ static void pump_transfers(unsigned long data) chip = dws->cur_chip; spi = message->spi; - if (unlikely(!chip->clk_div)) - chip->clk_div = dws->max_freq / chip->speed_hz; - if (message->state == ERROR_STATE) { message->status = -EIO; goto early_exit; @@ -419,7 +416,7 @@ static void pump_transfers(unsigned long data) if (transfer->speed_hz) { speed = chip->speed_hz; - if (transfer->speed_hz != speed) { + if ((transfer->speed_hz != speed) || (!chip->clk_div)) { speed = transfer->speed_hz; /* clk_div doesn't support odd number */ @@ -581,7 +578,6 @@ static int dw_spi_setup(struct spi_device *spi) dev_err(&spi->dev, "No max speed HZ parameter\n"); return -EINVAL; } - chip->speed_hz = spi->max_speed_hz; chip->tmode = 0; /* Tx & Rx */ /* Default SPI mode is SCPOL = 0, SCPH = 0 */ -- cgit v1.2.3-58-ga151 From 9c4b19a07dddda3ba35a2eb9b4134d485908e2f5 Mon Sep 17 00:00:00 2001 From: Qipan Li Date: Mon, 17 Nov 2014 23:17:02 +0800 Subject: spi: sirf: fix word width configuration commit 8c328a262f ("spi: sirf: Avoid duplicate code in various bits_per_word cases") is wrong in setting data width register of fifo is not right, it should use sspi->word_width >> 1 to set related bits. According to hardware spec, the mapping between register value and data width: 0 - byte 1 - WORD 2 - DWORD Fixes: 8c328a262f ("spi: sirf: Avoid duplicate code in various bits_per_word cases") is wrong in setting data width register of Signed-off-by: Qipan Li Signed-off-by: Barry Song Signed-off-by: Mark Brown Cc: stable@vger.kernel.org --- drivers/spi/spi-sirf.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/spi/spi-sirf.c b/drivers/spi/spi-sirf.c index 39e2c0a55a28..f63de781c729 100644 --- a/drivers/spi/spi-sirf.c +++ b/drivers/spi/spi-sirf.c @@ -562,9 +562,9 @@ spi_sirfsoc_setup_transfer(struct spi_device *spi, struct spi_transfer *t) sspi->word_width = DIV_ROUND_UP(bits_per_word, 8); txfifo_ctrl = SIRFSOC_SPI_FIFO_THD(SIRFSOC_SPI_FIFO_SIZE / 2) | - sspi->word_width; + (sspi->word_width >> 1); rxfifo_ctrl = SIRFSOC_SPI_FIFO_THD(SIRFSOC_SPI_FIFO_SIZE / 2) | - sspi->word_width; + (sspi->word_width >> 1); if (!(spi->mode & SPI_CS_HIGH)) regval |= SIRFSOC_SPI_CS_IDLE_STAT; -- cgit v1.2.3-58-ga151