| Age | Commit message (Collapse) | Author |
|---|
|
This commit switches to use the LoongArch's built-in rustc target
'loongarch64-unknown-none-softfloat'. The Rust samples have been tested.
Acked-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: WANG Rui <wangrui@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch updates from Huacai Chen:
- Add objtool support for LoongArch
- Add ORC stack unwinder support for LoongArch
- Add kernel livepatching support for LoongArch
- Select ARCH_HAS_CURRENT_STACK_POINTER in Kconfig
- Select HAVE_ARCH_USERFAULTFD_MINOR in Kconfig
- Some bug fixes and other small changes
* tag 'loongarch-6.9' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
LoongArch/crypto: Clean up useless assignment operations
LoongArch: Define the __io_aw() hook as mmiowb()
LoongArch: Remove superfluous flush_dcache_page() definition
LoongArch: Move {dmw,tlb}_virt_to_page() definition to page.h
LoongArch: Change __my_cpu_offset definition to avoid mis-optimization
LoongArch: Select HAVE_ARCH_USERFAULTFD_MINOR in Kconfig
LoongArch: Select ARCH_HAS_CURRENT_STACK_POINTER in Kconfig
LoongArch: Add kernel livepatching support
LoongArch: Add ORC stack unwinder support
objtool: Check local label in read_unwind_hints()
objtool: Check local label in add_dead_ends()
objtool/LoongArch: Enable orc to be built
objtool/x86: Separate arch-specific and generic parts
objtool/LoongArch: Implement instruction decoder
objtool/LoongArch: Enable objtool to be built
|
|
The kernel CONFIG_UNWINDER_ORC option enables the ORC unwinder, which is
similar in concept to a DWARF unwinder. The difference is that the format
of the ORC data is much simpler than DWARF, which in turn allows the ORC
unwinder to be much simpler and faster.
The ORC data consists of unwind tables which are generated by objtool.
After analyzing all the code paths of a .o file, it determines information
about the stack state at each instruction address in the file and outputs
that information to the .orc_unwind and .orc_unwind_ip sections.
The per-object ORC sections are combined at link time and are sorted and
post-processed at boot time. The unwinder uses the resulting data to
correlate instruction addresses with their stack states at run time.
Most of the logic are similar with x86, in order to get ra info before ra
is saved into stack, add ra_reg and ra_offset into orc_entry. At the same
time, modify some arch-specific code to silence the objtool warnings.
Co-developed-by: Jinyang He <hejinyang@loongson.cn>
Signed-off-by: Jinyang He <hejinyang@loongson.cn>
Co-developed-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Huacai Chen <chenhuacai@loongson.cn>
|
|
Eventually we want all architectures to be using the target as defined
by rustc. However currently some architectures can't do that and are
using the target.json specification. This puts in place the foundation
to allow the use of the builtin target definition or a target.json
specification.
Signed-off-by: Jamie Cunliffe <Jamie.Cunliffe@arm.com>
Acked-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20231020155056.3495121-2-Jamie.Cunliffe@arm.com
[catalin.marinas@arm.com: squashed loongarch ifneq fix from WANG Rui]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Rust has documentation tests: these are typically examples of
usage of any item (e.g. function, struct, module...).
They are very convenient because they are just written
alongside the documentation. For instance:
/// Sums two numbers.
///
/// ```
/// assert_eq!(mymod::f(10, 20), 30);
/// ```
pub fn f(a: i32, b: i32) -> i32 {
a + b
}
In userspace, the tests are collected and run via `rustdoc`.
Using the tool as-is would be useful already, since it allows
to compile-test most tests (thus enforcing they are kept
in sync with the code they document) and run those that do not
depend on in-kernel APIs.
However, by transforming the tests into a KUnit test suite,
they can also be run inside the kernel. Moreover, the tests
get to be compiled as other Rust kernel objects instead of
targeting userspace.
On top of that, the integration with KUnit means the Rust
support gets to reuse the existing testing facilities. For
instance, the kernel log would look like:
KTAP version 1
1..1
KTAP version 1
# Subtest: rust_doctests_kernel
1..59
# rust_doctest_kernel_build_assert_rs_0.location: rust/kernel/build_assert.rs:13
ok 1 rust_doctest_kernel_build_assert_rs_0
# rust_doctest_kernel_build_assert_rs_1.location: rust/kernel/build_assert.rs:56
ok 2 rust_doctest_kernel_build_assert_rs_1
# rust_doctest_kernel_init_rs_0.location: rust/kernel/init.rs:122
ok 3 rust_doctest_kernel_init_rs_0
...
# rust_doctest_kernel_types_rs_2.location: rust/kernel/types.rs:150
ok 59 rust_doctest_kernel_types_rs_2
# rust_doctests_kernel: pass:59 fail:0 skip:0 total:59
# Totals: pass:59 fail:0 skip:0 total:59
ok 1 rust_doctests_kernel
Therefore, add support for running Rust documentation tests
in KUnit. Some other notes about the current implementation
and support follow.
The transformation is performed by a couple scripts written
as Rust hostprogs.
Tests using the `?` operator are also supported as usual, e.g.:
/// ```
/// # use kernel::{spawn_work_item, workqueue};
/// spawn_work_item!(workqueue::system(), || pr_info!("x"))?;
/// # Ok::<(), Error>(())
/// ```
The tests are also compiled with Clippy under `CLIPPY=1`, just
like normal code, thus also benefitting from extra linting.
The names of the tests are currently automatically generated.
This allows to reduce the burden for documentation writers,
while keeping them fairly stable for bisection. This is an
improvement over the `rustdoc`-generated names, which include
the line number; but ideally we would like to get `rustdoc` to
provide the Rust item path and a number (for multiple examples
in a single documented Rust item).
In order for developers to easily see from which original line
a failed doctests came from, a KTAP diagnostic line is printed
to the log, containing the location (file and line) of the
original test (i.e. instead of the location in the generated
Rust file):
# rust_doctest_kernel_types_rs_2.location: rust/kernel/types.rs:150
This line follows the syntax for declaring test metadata in the
proposed KTAP v2 spec [1], which may be used for the proposed
KUnit test attributes API [2]. Thus hopefully this will make
migration easier later on (suggested by David [3]).
The original line in that test attribute is figured out by
providing an anchor (suggested by Boqun [4]). The original file
is found by walking the filesystem, checking directory prefixes
to reduce the amount of combinations to check, and it is only
done once per file. Ambiguities are detected and reported.
A notable difference from KUnit C tests is that the Rust tests
appear to assert using the usual `assert!` and `assert_eq!`
macros from the Rust standard library (`core`). We provide
a custom version that forwards the call to KUnit instead.
Importantly, these macros do not require passing context,
unlike the KUnit C ones (i.e. `struct kunit *`). This makes
them easier to use, and readers of the documentation do not need
to care about which testing framework is used. In addition, it
may allow us to test third-party code more easily in the future.
However, a current limitation is that KUnit does not support
assertions in other tasks. Thus we presently simply print an
error to the kernel log if an assertion actually failed. This
should be revisited to properly fail the test, perhaps saving
the context somewhere else, or letting KUnit handle it.
Link: https://lore.kernel.org/lkml/20230420205734.1288498-1-rmoar@google.com/ [1]
Link: https://lore.kernel.org/linux-kselftest/20230707210947.1208717-1-rmoar@google.com/ [2]
Link: https://lore.kernel.org/rust-for-linux/CABVgOSkOLO-8v6kdAGpmYnZUb+LKOX0CtYCo-Bge7r_2YTuXDQ@mail.gmail.com/ [3]
Link: https://lore.kernel.org/rust-for-linux/ZIps86MbJF%2FiGIzd@boqun-archlinux/ [4]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
Reviewed-by: David Gow <davidgow@google.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Commit 5c3d1d0abb12 ("kbuild: add a tool to list files ignored by git")
added a new tool, scripts/list-gitignored. My intention was to create
source packages without cleaning the source tree, without relying on git.
Linus strongly objected to it, and suggested using 'git archive' instead.
[1] [2] [3]
This commit goes in that direction - Remove scripts/list-gitignored.c
and rewrites Makefiles and scripts to use 'git archive' for building
Debian and RPM source packages. It also makes 'make perf-tar*-src-pkg'
use 'git archive' again.
Going forward, building source packages is only possible in a git-managed
tree. Building binary packages does not require git.
[1]: https://lore.kernel.org/lkml/CAHk-=wi49sMaC7vY1yMagk7eqLK=1jHeHQ=yZ_k45P=xBccnmA@mail.gmail.com/
[2]: https://lore.kernel.org/lkml/CAHk-=wh5AixGsLeT0qH2oZHKq0FLUTbyTw4qY921L=PwYgoGVw@mail.gmail.com/
[3]: https://lore.kernel.org/lkml/CAHk-=wgM-W6Fu==EoAVCabxyX8eYBz9kNC88-tm9ExRQwA79UQ@mail.gmail.com/
Fixes: 5c3d1d0abb12 ("kbuild: add a tool to list files ignored by git")
Fixes: e0ca16749ac3 ("kbuild: make perf-tar*-src-pkg work without relying on git")
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
In short, the motivation of this commit is to build a source package
without cleaning the source tree.
The deb-pkg and (src)rpm-pkg targets first run 'make clean' before
creating a source tarball. Otherwise build artifacts such as *.o,
*.a, etc. would be included in the tarball. Yet, the tarball ends up
containing several garbage files since 'make clean' does not clean
everything.
Cleaning the tree every time is annoying since it makes the incremental
build impossible. It is desirable to create a source tarball without
cleaning the tree.
In fact, there are some ways to achieve this.
The easiest solution is 'git archive'. 'make perf-tar*-src-pkg' uses
it, but I do not like it because it works only when the source tree is
managed by git, and all files you want in the tarball must be committed
in advance.
I want to make it work without relying on git. We can do this.
Files that are ignored by git are generated files, so should be excluded
from the source tarball. We can list them out by parsing the .gitignore
files. Of course, .gitignore does not cover all the cases, but it works
well enough.
tar(1) claims to support it:
--exclude-vcs-ignores
Exclude files that match patterns read from VCS-specific ignore files.
Supported files are: .cvsignore, .gitignore, .bzrignore, and .hgignore.
The best scenario would be to use 'tar --exclude-vcs-ignores', but this
option does not work. --exclude-vcs-ignore does not understand any of
the negation (!), preceding slash, following slash, etc.. So, this option
is just useless.
Hence, I wrote this gitignore parser. The previous version [1], written
in Python, was so slow. This version is implemented in C, so it works
much faster.
I imported the code from git (commit: 23c56f7bd5f1), so we get the same
result.
This tool traverses the source tree, parsing all .gitignore files, and
prints file paths that are ignored by git.
The output is similar to 'git ls-files --ignored --directory --others
--exclude-per-directory=.gitignore', except
[1] Not sorted
[2] No trailing slash for directories
[2] is intentional because tar's --exclude-from option cannot handle
trailing slashes.
[How to test this tool]
$ git clean -dfx
$ make -s -j$(nproc) defconfig all # or allmodconifg or whatever
$ git archive -o ../linux1.tar --prefix=./ HEAD
$ tar tf ../linux1.tar | LANG=C sort > ../file-list1 # files emitted by 'git archive'
$ make scripts_package
HOSTCC scripts/list-gitignored
$ scripts/list-gitignored --prefix=./ -o ../exclude-list
$ tar cf ../linux2.tar --exclude-from=../exclude-list .
$ tar tf ../linux2.tar | LANG=C sort > ../file-list2 # files emitted by 'tar'
$ diff ../file-list1 ../file-list2 | grep -E '^(<|>)'
< ./Documentation/devicetree/bindings/.yamllint
< ./drivers/clk/.kunitconfig
< ./drivers/gpu/drm/tests/.kunitconfig
< ./drivers/hid/.kunitconfig
< ./fs/ext4/.kunitconfig
< ./fs/fat/.kunitconfig
< ./kernel/kcsan/.kunitconfig
< ./lib/kunit/.kunitconfig
< ./mm/kfence/.kunitconfig
< ./tools/testing/selftests/arm64/tags/
< ./tools/testing/selftests/arm64/tags/.gitignore
< ./tools/testing/selftests/arm64/tags/Makefile
< ./tools/testing/selftests/arm64/tags/run_tags_test.sh
< ./tools/testing/selftests/arm64/tags/tags_test.c
< ./tools/testing/selftests/kvm/.gitignore
< ./tools/testing/selftests/kvm/Makefile
< ./tools/testing/selftests/kvm/config
< ./tools/testing/selftests/kvm/settings
The source tarball contains most of files that are tracked by git. You
see some diffs, but it is just because some .gitignore files are wrong.
$ git ls-files -i -c --exclude-per-directory=.gitignore
Documentation/devicetree/bindings/.yamllint
drivers/clk/.kunitconfig
drivers/gpu/drm/tests/.kunitconfig
drivers/hid/.kunitconfig
fs/ext4/.kunitconfig
fs/fat/.kunitconfig
kernel/kcsan/.kunitconfig
lib/kunit/.kunitconfig
mm/kfence/.kunitconfig
tools/testing/selftests/arm64/tags/.gitignore
tools/testing/selftests/arm64/tags/Makefile
tools/testing/selftests/arm64/tags/run_tags_test.sh
tools/testing/selftests/arm64/tags/tags_test.c
tools/testing/selftests/kvm/.gitignore
tools/testing/selftests/kvm/Makefile
tools/testing/selftests/kvm/config
tools/testing/selftests/kvm/settings
[1]: https://lore.kernel.org/all/20230128173843.765212-1-masahiroy@kernel.org/
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Commit 80f8be7af03f ("tomoyo: Omit use of bin2c") removed the last
use of bin2c.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
Reviewed-by: Sedat Dilek <sedat.dilek@gmail.com>
|
|
scripts/ is a better place to generate files used treewide.
With target.json moved to scripts/, you do not need to add target.json
to no-clean-files or MRPROPER_FILES.
'make clean' does not visit scripts/, but 'make mrproper' does.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Tested-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Having most of the new files in place, we now enable Rust support
in the build system, including `Kconfig` entries related to Rust,
the Rust configuration printer and a few other bits.
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Co-developed-by: Alex Gaynor <alex.gaynor@gmail.com>
Signed-off-by: Alex Gaynor <alex.gaynor@gmail.com>
Co-developed-by: Finn Behrens <me@kloenk.de>
Signed-off-by: Finn Behrens <me@kloenk.de>
Co-developed-by: Adam Bratschi-Kaye <ark.email@gmail.com>
Signed-off-by: Adam Bratschi-Kaye <ark.email@gmail.com>
Co-developed-by: Wedson Almeida Filho <wedsonaf@google.com>
Signed-off-by: Wedson Almeida Filho <wedsonaf@google.com>
Co-developed-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Co-developed-by: Sven Van Asbroeck <thesven73@gmail.com>
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Co-developed-by: Gary Guo <gary@garyguo.net>
Signed-off-by: Gary Guo <gary@garyguo.net>
Co-developed-by: Boris-Chengbiao Zhou <bobo1239@web.de>
Signed-off-by: Boris-Chengbiao Zhou <bobo1239@web.de>
Co-developed-by: Boqun Feng <boqun.feng@gmail.com>
Signed-off-by: Boqun Feng <boqun.feng@gmail.com>
Co-developed-by: Douglas Su <d0u9.su@outlook.com>
Signed-off-by: Douglas Su <d0u9.su@outlook.com>
Co-developed-by: Dariusz Sosnowski <dsosnowski@dsosnowski.pl>
Signed-off-by: Dariusz Sosnowski <dsosnowski@dsosnowski.pl>
Co-developed-by: Antonio Terceiro <antonio.terceiro@linaro.org>
Signed-off-by: Antonio Terceiro <antonio.terceiro@linaro.org>
Co-developed-by: Daniel Xu <dxu@dxuuu.xyz>
Signed-off-by: Daniel Xu <dxu@dxuuu.xyz>
Co-developed-by: Björn Roy Baron <bjorn3_gh@protonmail.com>
Signed-off-by: Björn Roy Baron <bjorn3_gh@protonmail.com>
Co-developed-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Signed-off-by: Martin Rodriguez Reboredo <yakoyoku@gmail.com>
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Add HOSTPKG_CONFIG to allow tooling that builds the kernel to override
what pkg-config and parameters are used.
Signed-off-by: Chun-Tse Shao <ctshao@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
First S390 complained that the sorting of the mcount sections at build
time caused the kernel to crash on their architecture. Now PowerPC is
complaining about it too. And also ARM64 appears to be having issues.
It may be necessary to also update the relocation table for the values
in the mcount table. Not only do we have to sort the table, but also
update the relocations that may be applied to the items in the table.
If the system is not relocatable, then it is fine to sort, but if it is,
some architectures may have issues (although x86 does not as it shifts all
addresses the same).
Add a HAVE_BUILDTIME_MCOUNT_SORT that an architecture can set to say it is
safe to do the sorting at build time.
Also update the config to compile in build time sorting in the sorttable
code in scripts/ to depend on CONFIG_BUILDTIME_MCOUNT_SORT.
Link: https://lore.kernel.org/all/944D10DA-8200-4BA9-8D0A-3BED9AA99F82@linux.ibm.com/
Link: https://lkml.kernel.org/r/20220127153821.3bc1ac6e@gandalf.local.home
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Yinan Liu <yinan@linux.alibaba.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Reported-by: Sachin Sant <sachinp@linux.ibm.com>
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Mark Rutland <mark.rutland@arm.com> [arm64]
Tested-by: Sachin Sant <sachinp@linux.ibm.com>
Fixes: 72b3942a173c ("scripts: ftrace - move the sort-processing in ftrace_init")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- Add new kconfig target 'make mod2noconfig', which will be useful to
speed up the build and test iteration.
- Raise the minimum supported version of LLVM to 11.0.0
- Refactor certs/Makefile
- Change the format of include/config/auto.conf to stop double-quoting
string type CONFIG options.
- Fix ARCH=sh builds in dash
- Separate compression macros for general purposes (cmd_bzip2 etc.) and
the ones for decompressors (cmd_bzip2_with_size etc.)
- Misc Makefile cleanups
* tag 'kbuild-v5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
kbuild: add cmd_file_size
arch: decompressor: remove useless vmlinux.bin.all-y
kbuild: rename cmd_{bzip2,lzma,lzo,lz4,xzkern,zstd22}
kbuild: drop $(size_append) from cmd_zstd
sh: rename suffix-y to suffix_y
doc: kbuild: fix default in `imply` table
microblaze: use built-in function to get CPU_{MAJOR,MINOR,REV}
certs: move scripts/extract-cert to certs/
kbuild: do not quote string values in include/config/auto.conf
kbuild: do not include include/config/auto.conf from shell scripts
certs: simplify $(srctree)/ handling and remove config_filename macro
kbuild: stop using config_filename in scripts/Makefile.modsign
certs: remove misleading comments about GCC PR
certs: refactor file cleaning
certs: remove unneeded -I$(srctree) option for system_certificates.o
certs: unify duplicated cmd_extract_certs and improve the log
certs: use $< and $@ to simplify the key generation rule
kbuild: remove headers_check stub
kbuild: move headers_check.pl to usr/include/
certs: use if_changed to re-generate the key when the key type is changed
...
|
|
When the kernel starts, the initialization of ftrace takes
up a portion of the time (approximately 6~8ms) to sort mcount
addresses. We can save this time by moving mcount-sorting to
compile time.
Link: https://lkml.kernel.org/r/20211212113358.34208-2-yinan@linux.alibaba.com
Signed-off-by: Yinan Liu <yinan@linux.alibaba.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
extract-cert is only used in certs/Makefile.
Move it there and build extract-cert on demand.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull x509 dbx/mokx UEFI support from David Howells:
"Here's a set of patches from Eric Snowberg[1] that add support for
EFI_CERT_X509_GUID entries in the dbx and mokx UEFI tables (such
entries cause matching certificates to be rejected).
These are currently ignored and only the hash entries are made use of.
Additionally Eric included his patches to allow such certificates to
be preloaded.
These patches deal with CVE-2020-26541.
To quote Eric:
'This is the fifth patch series for adding support for
EFI_CERT_X509_GUID entries [2]. It has been expanded to not only
include dbx entries but also entries in the mokx. Additionally
my series to preload these certificate [3] has also been
included'"
Link: https://lore.kernel.org/r/20210122181054.32635-1-eric.snowberg@oracle.com [1]
Link: https://patchwork.kernel.org/project/linux-security-module/patch/20200916004927.64276-1-eric.snowberg@oracle.com/ [2]
Link: https://lore.kernel.org/patchwork/cover/1315485/ [3]
* tag 'keys-cve-2020-26541-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
integrity: Load mokx variables into the blacklist keyring
certs: Add ability to preload revocation certs
certs: Move load_system_certificate_list to a common function
certs: Add EFI_CERT_X509_GUID support for dbx entries
|
|
Add a new Kconfig option called SYSTEM_REVOCATION_KEYS. If set,
this option should be the filename of a PEM-formated file containing
X.509 certificates to be included in the default blacklist keyring.
DH Changes:
- Make the new Kconfig option depend on SYSTEM_REVOCATION_LIST.
- Fix SYSTEM_REVOCATION_KEYS=n, but CONFIG_SYSTEM_REVOCATION_LIST=y[1][2].
- Use CONFIG_SYSTEM_REVOCATION_LIST for extract-cert[3].
- Use CONFIG_SYSTEM_REVOCATION_LIST for revocation_certificates.o[3].
Signed-off-by: Eric Snowberg <eric.snowberg@oracle.com>
Acked-by: Jarkko Sakkinen <jarkko@kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Randy Dunlap <rdunlap@infradead.org>
cc: keyrings@vger.kernel.org
Link: https://lore.kernel.org/r/e1c15c74-82ce-3a69-44de-a33af9b320ea@infradead.org/ [1]
Link: https://lore.kernel.org/r/20210303034418.106762-1-eric.snowberg@oracle.com/ [2]
Link: https://lore.kernel.org/r/20210304175030.184131-1-eric.snowberg@oracle.com/ [3]
Link: https://lore.kernel.org/r/20200930201508.35113-3-eric.snowberg@oracle.com/
Link: https://lore.kernel.org/r/20210122181054.32635-4-eric.snowberg@oracle.com/ # v5
Link: https://lore.kernel.org/r/161428673564.677100.4112098280028451629.stgit@warthog.procyon.org.uk/
Link: https://lore.kernel.org/r/161433312452.902181.4146169951896577982.stgit@warthog.procyon.org.uk/ # v2
Link: https://lore.kernel.org/r/161529606657.163428.3340689182456495390.stgit@warthog.procyon.org.uk/ # v3
|
|
Fixes: 2cea4a7a1885 ("scripts: use pkg-config to locate libcrypto")
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org # 5.6.x
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
Otherwise build fails if the headers are not in the default location. While at
it also ask pkg-config for the libs, with fallback to the existing value.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
Cc: stable@vger.kernel.org # 5.6.x
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
There was a request to preprocess the module linker script like we
do for the vmlinux one. (https://lkml.org/lkml/2020/8/21/512)
The difference between vmlinux.lds and module.lds is that the latter
is needed for external module builds, thus must be cleaned up by
'make mrproper' instead of 'make clean'. Also, it must be created
by 'make modules_prepare'.
You cannot put it in arch/$(SRCARCH)/kernel/, which is cleaned up by
'make clean'. I moved arch/$(SRCARCH)/kernel/module.lds to
arch/$(SRCARCH)/include/asm/module.lds.h, which is included from
scripts/module.lds.S.
scripts/module.lds is fine because 'make clean' keeps all the
build artifacts under scripts/.
You can add arch-specific sections in <asm/module.lds.h>.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Jessica Yu <jeyu@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Palmer Dabbelt <palmerdabbelt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Jessica Yu <jeyu@kernel.org>
|
|
To build host programs, you need to add the program names to 'hostprogs'
to use the necessary build rule, but it is not enough to build them
because there is no dependency.
There are two types of host programs: built as the prerequisite of
another (e.g. gen_crc32table in lib/Makefile), or always built when
Kbuild visits the Makefile (e.g. genksyms in scripts/genksyms/Makefile).
The latter is typical in Makefiles under scripts/, which contains host
programs globally used during the kernel build. To build them, you need
to add them to both 'hostprogs' and 'always-y'.
This commit adds hostprogs-always-y as a shorthand.
The same applies to user programs. net/bpfilter/Makefile builds
bpfilter_umh on demand, hence always-y is unneeded. In contrast,
programs under samples/ are added to both 'userprogs' and 'always-y'
so they are always built when Kbuild visits the Makefiles.
userprogs-always-y works as a shorthand.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
I do not like to add an extra include path for every tool with no
good reason. This should be specified per file.
This line was added by commit 6520fe5564ac ("x86, realmode: 16-bit
real-mode code support for relocs tool"), which did not touch
anything else in scripts/. I see no reason to add this.
Also, remove the comment about kallsyms because we do not have any
for the rest of programs.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
In old days, the "host-progs" syntax was used for specifying host
programs. It was renamed to the current "hostprogs-y" in 2004.
It is typically useful in scripts/Makefile because it allows Kbuild to
selectively compile host programs based on the kernel configuration.
This commit renames like follows:
always -> always-y
hostprogs-y -> hostprogs
So, scripts/Makefile will look like this:
always-$(CONFIG_BUILD_BIN2C) += ...
always-$(CONFIG_KALLSYMS) += ...
...
hostprogs := $(always-y) $(always-m)
I think this makes more sense because a host program is always a host
program, irrespective of the kernel configuration. We want to specify
which ones to compile by CONFIG options, so always-y will be handier.
The "always", "hostprogs-y", "hostprogs-m" will be kept for backward
compatibility for a while.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
|
|
scripts/conmakehash is only used for generating
drivers/tty/vt/consolemap_deftbl.c
Move it to the related directory.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Link: https://lore.kernel.org/r/20191217110633.8796-1-masahiroy@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ORC unwinder has two tables: .orc_unwind_ip and .orc_unwind, which
need to be sorted for binary search. Previously this sorting was done
during bootup.
Sort them at build time to speed up booting.
Add the ORC tables sorting in a parallel build process to speed up the build.
[ mingo: Rewrote the changelog and fixed some comments. ]
Suggested-by: Andy Lutomirski <luto@amacapital.net>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Shile Zhang <shile.zhang@linux.alibaba.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: linux-kbuild@vger.kernel.org
Link: https://lkml.kernel.org/r/20191204004633.88660-7-shile.zhang@linux.alibaba.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Use a more generic name for additional table sorting usecases,
such as the upcoming ORC table sorting feature. This tool is
not tied to exception table sorting anymore.
No functional changes intended.
[ mingo: Rewrote the changelog. ]
Signed-off-by: Shile Zhang <shile.zhang@linux.alibaba.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: linux-kbuild@vger.kernel.org
Link: https://lkml.kernel.org/r/20191204004633.88660-6-shile.zhang@linux.alibaba.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This tool is only used by drivers/video/logo/Makefile. No reason to
keep it in scripts/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity
Pull integrity updates from Mimi Zohar:
"The major feature in this time is IMA support for measuring and
appraising appended file signatures. In addition are a couple of bug
fixes and code cleanup to use struct_size().
In addition to the PE/COFF and IMA xattr signatures, the kexec kernel
image may be signed with an appended signature, using the same
scripts/sign-file tool that is used to sign kernel modules.
Similarly, the initramfs may contain an appended signature.
This contained a lot of refactoring of the existing appended signature
verification code, so that IMA could retain the existing framework of
calculating the file hash once, storing it in the IMA measurement list
and extending the TPM, verifying the file's integrity based on a file
hash or signature (eg. xattrs), and adding an audit record containing
the file hash, all based on policy. (The IMA support for appended
signatures patch set was posted and reviewed 11 times.)
The support for appended signature paves the way for adding other
signature verification methods, such as fs-verity, based on a single
system-wide policy. The file hash used for verifying the signature and
the signature, itself, can be included in the IMA measurement list"
* 'next-integrity' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity:
ima: ima_api: Use struct_size() in kzalloc()
ima: use struct_size() in kzalloc()
sefltest/ima: support appended signatures (modsig)
ima: Fix use after free in ima_read_modsig()
MODSIGN: make new include file self contained
ima: fix freeing ongoing ahash_request
ima: always return negative code for error
ima: Store the measurement again when appraising a modsig
ima: Define ima-modsig template
ima: Collect modsig
ima: Implement support for module-style appended signatures
ima: Factor xattr_verify() out of ima_appraise_measurement()
ima: Add modsig appraise_type option for module-style appended signatures
integrity: Select CONFIG_KEYS instead of depending on it
PKCS#7: Introduce pkcs7_get_digest()
PKCS#7: Refactor verify_pkcs7_signature()
MODSIGN: Export module signature definitions
ima: initialize the "template" field with the default template
|
|
I am not a big fan of the $(objtree)/ hack for clean-files/clean-dirs.
These are created in the top of $(objtree), so let's clean them up
from the top Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
IMA will use the module_signature format for append signatures, so export
the relevant definitions and factor out the code which verifies that the
appended signature trailer is valid.
Also, create a CONFIG_MODULE_SIG_FORMAT option so that IMA can select it
and be able to use mod_check_sig() without having to depend on either
CONFIG_MODULE_SIG or CONFIG_MODULES.
s390 duplicated the definition of struct module_signature so now they can
use the new <linux/module_signature.h> header instead.
Signed-off-by: Thiago Jung Bauermann <bauerman@linux.ibm.com>
Acked-by: Jessica Yu <jeyu@kernel.org>
Reviewed-by: Philipp Rudo <prudo@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Mimi Zohar <zohar@linux.ibm.com>
|
|
Since commit 2aedcd098a94 ("kbuild: suppress annoying "... is up to date."
message"), if_changed and friends nicely suppress "is up to date" messages.
We do not need per-Makefile tricks.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Currently, Kbuild descends from scripts/Makefile to scripts/gdb/Makefile
just for creating symbolic links, but it does not need to do it so early.
Merge the two descending paths to simplify the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kieran Bingham <kieran.bingham@ideasonboard.com>
|
|
Now that 'archprepare' depends on 'scripts', Kbuild can descend into
scripts/gcc-plugins in a more standard way.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
|
|
I am eagar to build under the scripts/ directory only with $(HOSTCC),
but scripts/mod/ highly depends on the $(CC) and target arch headers.
That it why the 'scripts' target must depend on 'asm-generic',
'gcc-plugins', and $(autoksyms_h).
Move it to the 'prepare0' stage. I know this is a cheesy workaround,
but better than the current situation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
There is nothing arch specific about building dtb files other than their
location under /arch/*/boot/dts/. Keeping each arch aligned is a pain.
The dependencies and supported targets are all slightly different.
Also, a cross-compiler for each arch is needed, but really the host
compiler preprocessor is perfectly fine for building dtbs. Move the
build rules to a common location and remove the arch specific ones. This
is done in a single step to avoid warnings about overriding rules.
The build dependencies had been a mixture of 'scripts' and/or 'prepare'.
These pull in several dependencies some of which need a target compiler
(specifically devicetable-offsets.h) and aren't needed to build dtbs.
All that is really needed is dtc, so adjust the dependencies to only be
dtc.
This change enables support 'dtbs_install' on some arches which were
missing the target.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Acked-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Michal Marek <michal.lkml@markovi.net>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: linux-kbuild@vger.kernel.org
Cc: linux-snps-arc@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: uclinux-h8-devel@lists.sourceforge.jp
Cc: linux-mips@linux-mips.org
Cc: nios2-dev@lists.rocketboards.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-xtensa@linux-xtensa.org
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
In preparation for enabling command line LDLIBS, re-name HOST_LOADLIBES
to KBUILD_HOSTLDLIBS as the internal use only flags. Also rename
existing usage to HOSTLDLIBS for consistency. This should not have any
visible effects.
Signed-off-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Commit 8370edea81e3 ("bin2c: move bin2c in scripts/basic") moved bin2c
to the scripts/basic/ directory, incorrectly stating "Kexec wants to
use bin2c and it wants to use it really early in the build process.
See arch/x86/purgatory/ code in later patches."
Commit bdab125c9301 ("Revert "kexec/purgatory: Add clean-up for
purgatory directory"") and commit d6605b6bbee8 ("x86/build: Remove
unnecessary preparation for purgatory") removed the redundant
purgatory build magic entirely.
That means that the move of bin2c was unnecessary in the first place.
fixdep is the only host program that deserves to sit in the
scripts/basic/ directory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There were a few bits and pieces left over from the now-disused DocBook
toolchain; git rid of them.
Reported-by: Markus Heiser <markus.heiser@darmarit.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Now that we don't have any DocBook anymore, remove it from
the building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This patch allows to build the whole kernel with GCC plugins. It was ported from
grsecurity/PaX. The infrastructure supports building out-of-tree modules and
building in a separate directory. Cross-compilation is supported too.
Currently the x86, arm, arm64 and uml architectures enable plugins.
The directory of the gcc plugins is scripts/gcc-plugins. You can use a file or a directory
there. The plugins compile with these options:
* -fno-rtti: gcc is compiled with this option so the plugins must use it too
* -fno-exceptions: this is inherited from gcc too
* -fasynchronous-unwind-tables: this is inherited from gcc too
* -ggdb: it is useful for debugging a plugin (better backtrace on internal
errors)
* -Wno-narrowing: to suppress warnings from gcc headers (ipa-utils.h)
* -Wno-unused-variable: to suppress warnings from gcc headers (gcc_version
variable, plugin-version.h)
The infrastructure introduces a new Makefile target called gcc-plugins. It
supports all gcc versions from 4.5 to 6.0. The scripts/gcc-plugin.sh script
chooses the proper host compiler (gcc-4.7 can be built by either gcc or g++).
This script also checks the availability of the included headers in
scripts/gcc-plugins/gcc-common.h.
The gcc-common.h header contains frequently included headers for GCC plugins
and it has a compatibility layer for the supported gcc versions.
The gcc-generate-*-pass.h headers automatically generate the registration
structures for GIMPLE, SIMPLE_IPA, IPA and RTL passes.
Note that 'make clean' keeps the *.so files (only the distclean or mrproper
targets clean all) because they are needed for out-of-tree modules.
Based on work created by the PaX Team.
Signed-off-by: Emese Revfy <re.emese@gmail.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Michal Marek <mmarek@suse.com>
|
|
Place a system_extra_cert buffer of configurable size, right after the
system_certificate_list, so that inserted keys can be readily processed by
the existing mechanism. Added script takes a key file and a kernel image
and inserts its contents to the reserved area. The
system_certificate_list_size is also adjusted accordingly.
Call the script as:
scripts/insert-sys-cert -b <vmlinux> -c <certfile>
If vmlinux has no symbol table, supply System.map file with -s flag.
Subsequent runs replace the previously inserted key, instead of appending
the new one.
Signed-off-by: Mehmet Kayaalp <mkayaalp@linux.vnet.ibm.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
Currently the encoding of documents generated by DocBook depends on
the current locale. Make the output reproducible independently of
the locale, by setting the encoding to UTF-8 (LC_CTYPE=C.UTF-8) by
preference, or ASCII (LC_CTYPE=C) as a fallback.
LC_CTYPE can normally be overridden by LC_ALL, but the top-level
Makefile unsets that.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
[jc: added check-lc_ctype to .gitignore]
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Fix up the dependencies somewhat too, while we're at it.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Where an external PEM file or PKCS#11 URI is given, we can get the cert
from it for ourselves instead of making the user drop signing_key.x509
in place for us.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Move to using PKCS#7 messages as module signatures because:
(1) We have to be able to support the use of X.509 certificates that don't
have a subjKeyId set. We're currently relying on this to look up the
X.509 certificate in the trusted keyring list.
(2) PKCS#7 message signed information blocks have a field that supplies the
data required to match with the X.509 certificate that signed it.
(3) The PKCS#7 certificate carries fields that specify the digest algorithm
used to generate the signature in a standardised way and the X.509
certificates specify the public key algorithm in a standardised way - so
we don't need our own methods of specifying these.
(4) We now have PKCS#7 message support in the kernel for signed kexec purposes
and we can make use of this.
To make this work, the old sign-file script has been replaced with a program
that needs compiling in a previous patch. The rules to build it are added
here.
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Vivek Goyal <vgoyal@redhat.com>
|
|
This provides the basic infrastructure to load kernel-specific python
helper scripts when debugging the kernel in gdb.
The loading mechanism is based on gdb loading for <objfile>-gdb.py when
opening <objfile>. Therefore, this places a corresponding link to the
main helper script into the output directory that contains vmlinux.
The main scripts will pull in submodules containing Linux specific gdb
commands and functions. To avoid polluting the source directory with
compiled python modules, we link to them from the object directory.
Due to gdb.parse_and_eval and string redirection for gdb.execute, we
depend on gdb >= 7.2.
This feature is enabled via CONFIG_GDB_SCRIPTS.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Michal Marek <mmarek@suse.cz> [kbuild stuff]
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Borislav Petkov <bp@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch series does not do kernel signature verification yet. I plan
to post another patch series for that. Now distributions are already
signing PE/COFF bzImage with PKCS7 signature I plan to parse and verify
those signatures.
Primary goal of this patchset is to prepare groundwork so that kernel
image can be signed and signatures be verified during kexec load. This
should help with two things.
- It should allow kexec/kdump on secureboot enabled machines.
- In general it can help even without secureboot. By being able to verify
kernel image signature in kexec, it should help with avoiding module
signing restrictions. Matthew Garret showed how to boot into a custom
kernel, modify first kernel's memory and then jump back to old kernel and
bypass any policy one wants to.
This patch (of 15):
Kexec wants to use bin2c and it wants to use it really early in the build
process. See arch/x86/purgatory/ code in later patches.
So move bin2c in scripts/basic so that it can be built very early and
be usable by arch/x86/purgatory/
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
scripts/Makefile adds "selinux" to subdir-y or subdir- twice.
subdir-$(CONFIG_MODVERSIONS) += genksyms
subdir-y += mod
subdir-$(CONFIG_SECURITY_SELINUX) += selinux <--- here
subdir-$(CONFIG_DTC) += dtc
# Let clean descend into subdirs
subdir- += basic kconfig package selinux <--- again
The latter is redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
|
