| Age | Commit message (Collapse) | Author |
|---|
|
Currently, cfg80211 rejects updates of AID and listen interval parameters
for existing entries. This information is known only at association stage
and as a result it's impossible to update entries that were added
unassociated.
Fix this by allowing updates of these properies for stations that the
driver (or mac80211) assigned unassociated state.
This then fixes mac80211's use of NL80211_FEATURE_FULL_AP_CLIENT_STATE.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Channel context driver operations can sleep, so add might_sleep()
and document this.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow distinguishing the non-station case from the case of a
station without rates, by using -1 for the non-station case.
This value cannot be reached with a station since that many
legacy rates don't exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As WMM is required for HT/VHT operation, treat bad WMM parameters
more gracefully by falling back to default parameters instead of
not using WMM assocation. This makes it possible to still use HT
or VHT, although potentially with reduced quality of service due
to unintended WMM parameters.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Disabling WMM has a huge impact these days. It implies that
HT and VHT will be disabled which means that the throughput
will be drammatically reduced.
Since the AIFSN is a transmission parameter, we can play a
bit and fix it up to make it compliant with the 802.11
specification which requires it to be at least 2.
Increasing it from 1 to 2 will slightly reduce the
likelyhood to get a transmission opportunity compared to
other clients that would accept to set AIFSN=1, but at
least it will allow HT and VHT which is a huge gain.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function currently determines this value, for use in bss_info.qos,
based on the interface type itself. Make it a parameter instead and
set it with the same logic for now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
llid_in_use needs to be limited to stations of the same VIF, otherwise it
will cause a NULL deref as the sta_info of non-mesh-VIFs don't have
sta->mesh set.
Steps to reproduce:
modprobe mac80211_hwsim channels=2
iw phy phy0 interface add ibss0 type ibss
iw phy phy0 interface add mesh0 type mp
iw phy phy1 interface add ibss1 type ibss
iw phy phy1 interface add mesh1 type mp
ip link set ibss0 up
ip link set mesh0 up
ip link set ibss1 up
ip link set mesh1 up
iw dev ibss0 ibss join foo 2412
iw dev ibss1 ibss join foo 2412
# Ensure that ibss0 and ibss1 are actually associated; I often need to
# leave and join the cell on ibss1 a second time.
iw dev mesh0 mesh join bar
iw dev mesh1 mesh join bar # crash
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When 11n peers performs a TDLS connection on a legacy BSS, the HT
operation IE must be specified according to IEEE802.11-2012 section
9.23.3.2. Otherwise HT-protection is compromised and the medium becomes
noisy for both the TDLS and the BSS links.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Scheduled scan has to be reconfigured only if wowlan wasn't
configured, since otherwise it should continue to run (with
the 'any' trigger) or be aborted.
The current code will end up asking the driver to start a new
scheduled scan without stopping the previous one, and leaking
some memory (from the previous request.)
Fix this by doing the abort/restart under the proper conditions.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If drv_start() fails during hw_restart, all the running
interfaces are being closed/stopped, which results in
drv_stop() being called, although the driver was never
started successfully.
This might cause drivers to perform operations on uninitialized
memory (as they assume it was initialized on drv_start)
Consider the local->started flag, and call the driver's stop()
op only if drv_start() succeeded before.
Move drv_start() and drv_stop() to driver-ops.c, as they are no
longer simple wrappers.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The recalc_smps work can run after the station disassociates.
At this stage we already released the channel, but the work
will be cancelled only when the interface stops.
In this scenario we can hit the warning in ieee80211_recalc_smps, so
just remove it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Requesting hw restart during suspend might result
in the restart work being executed after mac80211
and the hw are suspended.
Solve the race by simply scheduling the restart
work on a freezable workqueue.
Note that there can be some cases of reconfiguration
on resume (besides the hardware restart):
* wowlan is not configured -
All the interfaces removed were removed on suspend,
and drv_stop() was called. At this point the driver
shouldn't expect for hw_restart anyway, so we can
simply cancel it (on resume).
* wowlan is configured, drv_resume() == 1
There is no definitive expected behavior in this case,
as each driver might have different expectations (e.g.
setting some flags on suspend/restart vs. not handling
spurious recovery).
For now, simply let the hw_restart work run again after
resume, and hope the driver will handle it well (or at
least initiate another hw restart).
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Local request to deauthenticate wasn't handled while associating, thus
the association could continue even when the user space required to
disconnect.
Cc: stable@vger.kernel.org
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In TDLS channel-switch operations the chandef can sometimes be NULL.
Avoid an oops in the trace code for these cases and just print a
chandef full of zeros.
Cc: stable@vger.kernel.org
Fixes: a7a6bdd0670fe ("mac80211: introduce TDLS channel switch ops")
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If parse_acl_data succeeds but the subsequent parsing of smps
attributes fails, there will be a memory leak due to early returns.
Fix that by moving the ACL parsing later.
Cc: stable@vger.kernel.org
Fixes: 18998c381b19b ("cfg80211: allow requesting SMPS mode on ap start")
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case of one shot NOA the interval can be 0, catch that
instead of potentially (depending on the driver) crashing
like this:
divide error: 0000 [#1] SMP
[...]
Call Trace:
<IRQ>
[<ffffffffc08e891c>] ieee80211_extend_absent_time+0x6c/0xb0 [mac80211]
[<ffffffffc08e8a17>] ieee80211_update_p2p_noa+0xb7/0xe0 [mac80211]
[<ffffffffc069cc30>] ath9k_p2p_ps_timer+0x170/0x190 [ath9k]
[<ffffffffc070adf8>] ath_gen_timer_isr+0xc8/0xf0 [ath9k_hw]
[<ffffffffc0691156>] ath9k_tasklet+0x296/0x2f0 [ath9k]
[<ffffffff8107ad65>] tasklet_action+0xe5/0xf0
[...]
Cc: stable@vger.kernel.org [3.16+, due to d463af4a1c34 using it]
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Here's another set of patches for the current cycle:
* I merged net-next back to avoid a conflict with the
* cfg80211 scheduled scan API extensions
* preparations for better scan result timestamping
* regulatory cleanups
* mac80211 statistics cleanups
* a few other small cleanups and fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With use of lwtunnel, we can directly call dev_queue_xmit()
rather than calling netdev vport send operation.
Following change make tunnel vport code bit cleaner.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Patch fixes following sparse warning.
net/openvswitch/flow_netlink.c:583:30: warning: incorrect type in assignment (different base types)
net/openvswitch/flow_netlink.c:583:30: expected restricted __be16 [usertype] ipv4
net/openvswitch/flow_netlink.c:583:30: got int
Fixes: 6b26ba3a7d ("openvswitch: netlink attributes for IPv6 tunneling")
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tom Herbert added SIT support to GRO with commit
19424e052fb4 ("sit: Add gro callbacks to sit_offload"),
later reverted by Herbert Xu.
The problem came because Tom patch was building GRO
packets without proper meta data : If packets were locally
delivered, we would not care.
But if packets needed to be forwarded, GSO engine was not
able to segment individual segments.
With the following patch, we correctly set skb->encapsulation
and inner network header. We also update gso_type.
Tested:
Server :
netserver
modprobe dummy
ifconfig dummy0 8.0.0.1 netmask 255.255.255.0 up
arp -s 8.0.0.100 4e:32:51:04:47:e5
iptables -I INPUT -s 10.246.7.151 -j TEE --gateway 8.0.0.100
ifconfig sixtofour0
sixtofour0 Link encap:IPv6-in-IPv4
inet6 addr: 2002:af6:798::1/128 Scope:Global
inet6 addr: 2002:af6:798::/128 Scope:Global
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:411169 errors:0 dropped:0 overruns:0 frame:0
TX packets:409414 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:20319631739 (20.3 GB) TX bytes:29529556 (29.5 MB)
Client :
netperf -H 2002:af6:798::1 -l 1000 &
Checked on server traffic copied on dummy0 and verify segments were
properly rebuilt, with proper IP headers, TCP checksums...
tcpdump on eth0 shows proper GRO aggregation takes place.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if_nlmsg_size() overestimates the minimum allocation size of netlink
dump request (when called from rtnl_calcit()) or the size of the
message (when called from rtnl_getlink()). This is because
ext_filter_mask is not supported by rtnl_link_get_af_size() and
rtnl_link_get_size().
The over-estimation is significant when at least one netdev has many
VLANs configured (8 bytes for each configured VLAN).
This patch-set "rightsizes" the protocol specific attribute size
calculation by propagating ext_filter_mask to rtnl_link_get_af_size()
and adding this a argument to get_link_af_size op in rtnl_af_ops.
Bridge module already used filtering aware sizing for notifications.
br_get_link_af_size_filtered() is consistent with the modified
get_link_af_size op so it replaces br_get_link_af_size() in br_af_ops.
br_get_link_af_size() becomes unused and thus removed.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configure ageing time to the HW for newly bridged device
CC: Scott Feldman <sfeldma@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements the second half of RACK that uses the the most
recent transmit time among all delivered packets to detect losses.
tcp_rack_mark_lost() is called upon receiving a dubious ACK.
It then checks if an not-yet-sacked packet was sent at least
"reo_wnd" prior to the sent time of the most recently delivered.
If so the packet is deemed lost.
The "reo_wnd" reordering window starts with 1msec for fast loss
detection and changes to min-RTT/4 when reordering is observed.
We found 1msec accommodates well on tiny degree of reordering
(<3 pkts) on faster links. We use min-RTT instead of SRTT because
reordering is more of a path property but SRTT can be inflated by
self-inflicated congestion. The factor of 4 is borrowed from the
delayed early retransmit and seems to work reasonably well.
Since RACK is still experimental, it is now used as a supplemental
loss detection on top of existing algorithms. It is only effective
after the fast recovery starts or after the timeout occurs. The
fast recovery is still triggered by FACK and/or dupack threshold
instead of RACK.
We introduce a new sysctl net.ipv4.tcp_recovery for future
experiments of loss recoveries. For now RACK can be disabled by
setting it to 0.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is the first half of the RACK loss recovery.
RACK loss recovery uses the notion of time instead
of packet sequence (FACK) or counts (dupthresh). It's inspired by the
previous FACK heuristic in tcp_mark_lost_retrans(): when a limited
transmit (new data packet) is sacked, then current retransmitted
sequence below the newly sacked sequence must been lost,
since at least one round trip time has elapsed.
But it has several limitations:
1) can't detect tail drops since it depends on limited transmit
2) is disabled upon reordering (assumes no reordering)
3) only enabled in fast recovery ut not timeout recovery
RACK (Recently ACK) addresses these limitations with the notion
of time instead: a packet P1 is lost if a later packet P2 is s/acked,
as at least one round trip has passed.
Since RACK cares about the time sequence instead of the data sequence
of packets, it can detect tail drops when later retransmission is
s/acked while FACK or dupthresh can't. For reordering RACK uses a
dynamically adjusted reordering window ("reo_wnd") to reduce false
positives on ever (small) degree of reordering.
This patch implements tcp_advanced_rack() which tracks the
most recent transmission time among the packets that have been
delivered (ACKed or SACKed) in tp->rack.mstamp. This timestamp
is the key to determine which packet has been lost.
Consider an example that the sender sends six packets:
T1: P1 (lost)
T2: P2
T3: P3
T4: P4
T100: sack of P2. rack.mstamp = T2
T101: retransmit P1
T102: sack of P2,P3,P4. rack.mstamp = T4
T205: ACK of P4 since the hole is repaired. rack.mstamp = T101
We need to be careful about spurious retransmission because it may
falsely advance tp->rack.mstamp by an RTT or an RTO, causing RACK
to falsely mark all packets lost, just like a spurious timeout.
We identify spurious retransmission by the ACK's TS echo value.
If TS option is not applicable but the retransmission is acknowledged
less than min-RTT ago, it is likely to be spurious. We refrain from
using the transmission time of these spurious retransmissions.
The second half is implemented in the next patch that marks packet
lost using RACK timestamp.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
a helper to prepare the main RACK patch
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the existing lost retransmit detection because RACK subsumes
it completely. This also stops the overloading the ack_seq field of
the skb control block.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kathleen Nichols' algorithm for tracking the minimum RTT of a
data stream over some measurement window. It uses constant space
and constant time per update. Yet it almost always delivers
the same minimum as an implementation that has to keep all
the data in the window. The measurement window is tunable via
sysctl.net.ipv4.tcp_min_rtt_wlen with a default value of 5 minutes.
The algorithm keeps track of the best, 2nd best & 3rd best min
values, maintaining an invariant that the measurement time of
the n'th best >= n-1'th best. It also makes sure that the three
values are widely separated in the time window since that bounds
the worse case error when that data is monotonically increasing
over the window.
Upon getting a new min, we can forget everything earlier because
it has no value - the new min is less than everything else in the
window by definition and it's the most recent. So we restart fresh
on every new min and overwrites the 2nd & 3rd choices. The same
property holds for the 2nd & 3rd best.
Therefore we have to maintain two invariants to maximize the
information in the samples, one on values (1st.v <= 2nd.v <=
3rd.v) and the other on times (now-win <=1st.t <= 2nd.t <= 3rd.t <=
now). These invariants determine the structure of the code
The RTT input to the windowed filter is the minimum RTT measured
from ACK or SACK, or as the last resort from TCP timestamps.
The accessor tcp_min_rtt() returns the minimum RTT seen in the
window. ~0U indicates it is not available. The minimum is 1usec
even if the true RTT is below that.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently ca_seq_rtt_us does not use Kern's check. Fix that by
checking if any packet acked is a retransmit, for both RTT used
for RTT estimation and congestion control.
Fixes: 5b08e47ca ("tcp: prefer packet timing to TS-ECR for RTT")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Group station statistics by where they're (mostly) updated
(TX, RX and TX-status) and group them into sub-structs of
the struct sta_info.
Also rename the variables since the grouping now makes it
obvious where they belong.
This makes it easier to identify where the statistics are
updated in the code, and thus easier to think about them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's little point in keeping (and even sending to userspace)
the beacon_loss_count value per station, since it can only apply
to the AP on a managed-mode connection. Move the value to ifmgd,
advertise it only in managed mode, and remove it from ethtool as
it's available through better interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This file only feeds a debugfs file that isn't very useful, so remove
it. If necessary, we can add other ways to get this information, for
example in the NL80211_CMD_PROBE_CLIENT response.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Account for extra headroom in ath9k driver, from Felix Fietkau.
2) Fix OOPS in pppoe driver due to incorrect socket state transition,
from Guillaume Nault.
3) Kill memory leak in amd-xgbe debugfx, from Geliang Tang.
4) Power management fixes for iwlwifi, from Johannes Berg.
5) Fix races in reqsk_queue_unlink(), from Eric Dumazet.
6) Fix dst_entry usage in ARP replies, from Jiri Benc.
7) Cure OOPSes with SO_GET_FILTER, from Daniel Borkmann.
8) Missing allocation failure check in amd-xgbe, from Tom Lendacky.
9) Various resource allocation/freeing cures in DSA< from Neil
Armstrong.
10) A series of bug fixes in the openvswitch conntrack support, from
Joe Stringer.
11) Fix two cases (BPF and act_mirred) where we have to clean the sender
cpu stored in the SKB before transmitting. From WANG Cong and
Alexei Starovoitov.
12) Disable VLAN filtering in promiscuous mode in mlx5 driver, from
Achiad Shochat.
13) Older bnx2x chips cannot do 4-tuple UDP hashing, so prevent this
configuration via ethtool. From Yuval Mintz.
14) Don't call rt6_uncached_list_flush_dev() from rt6_ifdown() when
'dev' is NULL, from Eric Biederman.
15) Prevent stalled link synchronization in tipc, from Jon Paul Maloy.
16) kcalloc() gstrings ethtool buffer before having driver fill it in,
in order to prevent kernel memory leaking. From Joe Perches.
17) Fix mixxing rt6_info initialization for blackhole routes, from
Martin KaFai Lau.
18) Kill VLAN regression in via-rhine, from Andrej Ota.
19) Missing pfmemalloc check in sk_add_backlog(), from Eric Dumazet.
20) Fix spurious MSG_TRUNC signalling in netlink dumps, from Ronen Arad.
21) Scrube SKBs when pushing them between namespaces in openvswitch,
from Joe Stringer.
22) bcmgenet enables link interrupts too early, fix from Florian
Fainelli.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (92 commits)
net: bcmgenet: Fix early link interrupt enabling
tunnels: Don't require remote endpoint or ID during creation.
openvswitch: Scrub skb between namespaces
xen-netback: correctly check failed allocation
net: asix: add support for the Billionton GUSB2AM-1G-B USB adapter
netlink: Trim skb to alloc size to avoid MSG_TRUNC
net: add pfmemalloc check in sk_add_backlog()
via-rhine: fix VLAN receive handling regression.
ipv6: Initialize rt6_info properly in ip6_blackhole_route()
ipv6: Move common init code for rt6_info to a new function rt6_info_init()
Bluetooth: Fix initializing conn_params in scan phase
Bluetooth: Fix conn_params list update in hci_connect_le_scan_cleanup
Bluetooth: Fix remove_device behavior for explicit connects
Bluetooth: Fix LE reconnection logic
Bluetooth: Fix reference counting for LE-scan based connections
Bluetooth: Fix double scan updates
mlxsw: core: Fix race condition in __mlxsw_emad_transmit
tipc: move fragment importance field to new header position
ethtool: Use kcalloc instead of kmalloc for ethtool_get_strings
tipc: eliminate risk of stalled link synchronization
...
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. Most relevantly, updates for the nfnetlink_log to integrate with
conntrack, fixes for cttimeout and improvements for nf_queue core, they are:
1) Remove useless ifdef around static inline function in IPVS, from
Eric W. Biederman.
2) Simplify the conntrack support for nfnetlink_queue: Merge
nfnetlink_queue_ct.c file into nfnetlink_queue_core.c, then rename it back
to nfnetlink_queue.c
3) Use y2038 safe timestamp from nfnetlink_queue.
4) Get rid of dead function definition in nf_conntrack, from Flavio
Leitner.
5) Attach conntrack support for nfnetlink_log.c, from Ken-ichirou MATSUZAWA.
This adds a new NETFILTER_NETLINK_GLUE_CT Kconfig switch that
controls enabling both nfqueue and nflog integration with conntrack.
The userspace application can request this via NFULNL_CFG_F_CONNTRACK
configuration flag.
6) Remove unused netns variables in IPVS, from Eric W. Biederman and
Simon Horman.
7) Don't put back the refcount on the cttimeout object from xt_CT on success.
8) Fix crash on cttimeout policy object removal. We have to flush out
the cttimeout extension area of the conntrack not to refer to an unexisting
object that was just removed.
9) Make sure rcu_callback completion before removing nfnetlink_cttimeout
module removal.
10) Fix compilation warning in br_netfilter when no nf_defrag_ipv4 and
nf_defrag_ipv6 are enabled. Patch from Arnd Bergmann.
11) Autoload ctnetlink dependencies when NFULNL_CFG_F_CONNTRACK is
requested. Again from Ken-ichirou MATSUZAWA.
12) Don't use pointer to previous hook when reinjecting traffic via
nf_queue with NF_REPEAT verdict since it may be already gone. This
also avoids a deadloop if the userspace application keeps returning
NF_REPEAT.
13) A bunch of cleanups for netfilter IPv4 and IPv6 code from Ian Morris.
14) Consolidate logger instance existence check in nfulnl_recv_config().
15) Fix broken atomicity when applying configuration updates to logger
instances in nfnetlink_log.
16) Get rid of the .owner attribute in our hook object. We don't need
this anymore since we're dropping pending packets that have escaped
from the kernel when unremoving the hook. Patch from Florian Westphal.
17) Remove unnecessary rcu_read_lock() from nf_reinject code, we always
assume RCU read side lock from .call_rcu in nfnetlink. Also from Florian.
18) Use static inline function instead of macros to define NF_HOOK() and
NF_HOOK_COND() when no netfilter support in on, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sowmini found hang with rds-ping while testing RDS over TCP. Its
a corner case and doesn't happen always. The issue is not reproducible
with IB transport. Its clear from below dump why we see it with RDS TCP.
[<ffffffff8153b7e5>] do_tcp_setsockopt+0xb5/0x740
[<ffffffff8153bec4>] tcp_setsockopt+0x24/0x30
[<ffffffff814d57d4>] sock_common_setsockopt+0x14/0x20
[<ffffffffa096071d>] rds_tcp_xmit_prepare+0x5d/0x70 [rds_tcp]
[<ffffffffa093b5f7>] rds_send_xmit+0xd7/0x740 [rds]
[<ffffffffa093bda2>] rds_send_pong+0x142/0x180 [rds]
[<ffffffffa0939d34>] rds_recv_incoming+0x274/0x330 [rds]
[<ffffffff810815ae>] ? ttwu_queue+0x11e/0x130
[<ffffffff814dcacd>] ? skb_copy_bits+0x6d/0x2c0
[<ffffffffa0960350>] rds_tcp_data_recv+0x2f0/0x3d0 [rds_tcp]
[<ffffffff8153d836>] tcp_read_sock+0x96/0x1c0
[<ffffffffa0960060>] ? rds_tcp_recv_init+0x40/0x40 [rds_tcp]
[<ffffffff814d6a90>] ? sock_def_write_space+0xa0/0xa0
[<ffffffffa09604d1>] rds_tcp_data_ready+0xa1/0xf0 [rds_tcp]
[<ffffffff81545249>] tcp_data_queue+0x379/0x5b0
[<ffffffffa0960cdb>] ? rds_tcp_write_space+0xbb/0x110 [rds_tcp]
[<ffffffff81547fd2>] tcp_rcv_established+0x2e2/0x6e0
[<ffffffff81552602>] tcp_v4_do_rcv+0x122/0x220
[<ffffffff81553627>] tcp_v4_rcv+0x867/0x880
[<ffffffff8152e0b3>] ip_local_deliver_finish+0xa3/0x220
This happens because rds_send_xmit() chain wants to take
sock_lock which is already taken by tcp_v4_rcv() on its
way to rds_tcp_data_ready(). Commit db6526dcb51b ("RDS: use
rds_send_xmit() state instead of RDS_LL_SEND_FULL") which
was trying to opportunistically finish the send request
in same thread context.
But because of above recursive lock hang with RDS TCP,
the send work from rds_send_pong() needs to deferred to
worker to avoid lock up. Given RDS ping is more of connectivity
test than performance critical path, its should be ok even
for transport like IB.
Reported-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the time of commit fff326990789 ("tcp: reflect SYN queue_mapping into
SYNACK packets") we had little ways to cope with SYN floods.
We no longer need to reflect incoming skb queue mappings, and instead
can pick a TX queue based on cpu cooking the SYNACK, with normal XPS
affinities.
Note that all SYNACK retransmits were picking TX queue 0, this no longer
is a win given that SYNACK rtx are now distributed on all cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If OVS receives a packet from another namespace, then the packet should
be scrubbed. However, people have already begun to rely on the behaviour
that skb->mark is preserved across namespaces, so retain this one field.
This is mainly to address information leakage between namespaces when
using OVS internal ports, but by placing it in ovs_vport_receive() it is
more generally applicable, meaning it should not be overlooked if other
port types are allowed to be moved into namespaces in future.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2015-10-16
First of all, sorry for the late set of patches for the 4.3 cycle. We
just finished an intensive week of testing at the Bluetooth UnPlugFest
and discovered (and fixed) issues there. Unfortunately a few issues
affect 4.3-rc5 in a way that they break existing Bluetooth LE mouse and
keyboard support.
The regressions result from supporting LE privacy in conjunction with
scanning for Resolvable Private Addresses before connecting. A feature
that has been tested heavily (including automated unit tests), but sadly
some regressions slipped in. The UnPlugFest with its multitude of test
platforms is a good battle testing ground for uncovering every corner
case.
The patches in this pull request focus only on fixing the regressions in
4.3-rc5. The patches look a bit larger since we also added comments in
the critical sections of the fixes to improve clarity.
I would appreciate if we can get these regression fixes to Linus
quickly. Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netlink_dump() allocates skb based on the calculated min_dump_alloc or
a per socket max_recvmsg_len.
min_alloc_size is maximum space required for any single netdev
attributes as calculated by rtnl_calcit().
max_recvmsg_len tracks the user provided buffer to netlink_recvmsg.
It is capped at 16KiB.
The intention is to avoid small allocations and to minimize the number
of calls required to obtain dump information for all net devices.
netlink_dump packs as many small messages as could fit within an skb
that was sized for the largest single netdev information. The actual
space available within an skb is larger than what is requested. It could
be much larger and up to near 2x with align to next power of 2 approach.
Allowing netlink_dump to use all the space available within the
allocated skb increases the buffer size a user has to provide to avoid
truncaion (i.e. MSG_TRUNG flag set).
It was observed that with many VLANs configured on at least one netdev,
a larger buffer of near 64KiB was necessary to avoid "Message truncated"
error in "ip link" or "bridge [-c[ompressvlans]] vlan show" when
min_alloc_size was only little over 32KiB.
This patch trims skb to allocated size in order to allow the user to
avoid truncation with more reasonable buffer size.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A dhcp server may provide parameters to a client from a pool of IP
addresses and using a shared rootfs, or provide a specific set of
parameters for a specific client, usually using the MAC address to
identify each client individually. The dhcp protocol also specifies
a client-id field which can be used to determine the correct
parameters to supply when no MAC address is available. There is
currently no way to tell the kernel to supply a specific client-id,
only the userspace dhcp clients support this feature, but this can
not be used when the network is needed before userspace is available
such as when the root filesystem is on NFS.
This patch is to be able to do something like "ip=dhcp,client_id_type,
client_id_value", as a kernel parameter to enable the kernel to
identify itself to the server.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
This merge resolves conflicts with 75aec9df3a78 ("bridge: Remove
br_nf_push_frag_xmit_sk") as part of Eric Biederman's effort to improve
netns support in the network stack that reached upstream via David's
net-next tree.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
net/bridge/br_netfilter_hooks.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph fixes from Sage Weil:
"Just two small items from Ilya:
The first patch fixes the RBD readahead to grab full objects. The
second fixes the write ops to prevent undue promotion when a cache
tier is configured on the server side"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: use writefull op for object size writes
rbd: set max_sectors explicitly
|
|
This patch cleanses whitespace around arithmetical operators.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Use tabs instead of spaces to indent code.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Use tabs instead of spaces to indent second line of parameters in
function definitions.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Correct whitespace layout of ternary operators in the netfilter-ipv4
code.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Whitespace cleansing: Labels should not be indented.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
A recent change to the dst_output handling caused a new warning
when the call to NF_HOOK() is the only used of a local variable
passed as 'dev', and CONFIG_NETFILTER is disabled:
net/ipv6/ip6_output.c: In function 'ip6_output':
net/ipv6/ip6_output.c:135:21: warning: unused variable 'dev' [-Wunused-variable]
The reason for this is that the NF_HOOK macro in this case does
not reference the variable at all, and the call to dev_net(dev)
got removed from the ip6_output function. To avoid that warning now
and in the future, this changes the macro into an equivalent
inline function, which tells the compiler that the variable is
passed correctly but still unused.
The dn_forward function apparently had the same problem in
the past and added a local workaround that no longer works
with the inline function. In order to avoid a regression, we
have to also remove the #ifdef from decnet in the same patch.
Fixes: ede2059dbaf9 ("dst: Pass net into dst->output")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
All verdict handlers make use of the nfnetlink .call_rcu callback
so rcu readlock is already held.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
We don't care if module is being unloaded anymore since hook unregister
handling will destroy queue entries using that hook.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
