| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from netfilter.
Current release - regressions:
- sched: act_pedit: free pedit keys on bail from offset check
Current release - new code bugs:
- pds_core:
- Kconfig fixes (DEBUGFS and AUXILIARY_BUS)
- fix mutex double unlock in error path
Previous releases - regressions:
- sched: cls_api: remove block_cb from driver_list before freeing
- nf_tables: fix ct untracked match breakage
- eth: mtk_eth_soc: drop generic vlan rx offload
- sched: flower: fix error handler on replace
Previous releases - always broken:
- tcp: fix skb_copy_ubufs() vs BIG TCP
- ipv6: fix skb hash for some RST packets
- af_packet: don't send zero-byte data in packet_sendmsg_spkt()
- rxrpc: timeout handling fixes after moving client call connection
to the I/O thread
- ixgbe: fix panic during XDP_TX with > 64 CPUs
- igc: RMW the SRRCTL register to prevent losing timestamp config
- dsa: mt7530: fix corrupt frames using TRGMII on 40 MHz XTAL MT7621
- r8152:
- fix flow control issue of RTL8156A
- fix the poor throughput for 2.5G devices
- move setting r8153b_rx_agg_chg_indicate() to fix coalescing
- enable autosuspend
- ncsi: clear Tx enable mode when handling a Config required AEN
- octeontx2-pf: macsec: fixes for CN10KB ASIC rev
Misc:
- 9p: remove INET dependency"
* tag 'net-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (69 commits)
net: bcmgenet: Remove phy_stop() from bcmgenet_netif_stop()
pds_core: fix mutex double unlock in error path
net/sched: flower: fix error handler on replace
Revert "net/sched: flower: Fix wrong handle assignment during filter change"
net/sched: flower: fix filter idr initialization
net: fec: correct the counting of XDP sent frames
bonding: add xdp_features support
net: enetc: check the index of the SFI rather than the handle
sfc: Add back mailing list
virtio_net: suppress cpu stall when free_unused_bufs
ice: block LAN in case of VF to VF offload
net: dsa: mt7530: fix network connectivity with multiple CPU ports
net: dsa: mt7530: fix corrupt frames using trgmii on 40 MHz XTAL MT7621
9p: Remove INET dependency
netfilter: nf_tables: fix ct untracked match breakage
af_packet: Don't send zero-byte data in packet_sendmsg_spkt().
igc: read before write to SRRCTL register
pds_core: add AUXILIARY_BUS and NET_DEVLINK to Kconfig
pds_core: remove CONFIG_DEBUG_FS from makefile
ionic: catch failure from devlink_alloc
...
|
|
afs_make_call() calls rxrpc_kernel_begin_call() to begin a call (which may
get stalled in the background waiting for a connection to become
available); it then calls rxrpc_kernel_set_max_life() to set the timeouts -
but that starts the call timer so the call timer might then expire before
we get a connection assigned - leading to the following oops if the call
stalled:
BUG: kernel NULL pointer dereference, address: 0000000000000000
...
CPU: 1 PID: 5111 Comm: krxrpcio/0 Not tainted 6.3.0-rc7-build3+ #701
RIP: 0010:rxrpc_alloc_txbuf+0xc0/0x157
...
Call Trace:
<TASK>
rxrpc_send_ACK+0x50/0x13b
rxrpc_input_call_event+0x16a/0x67d
rxrpc_io_thread+0x1b6/0x45f
? _raw_spin_unlock_irqrestore+0x1f/0x35
? rxrpc_input_packet+0x519/0x519
kthread+0xe7/0xef
? kthread_complete_and_exit+0x1b/0x1b
ret_from_fork+0x22/0x30
Fix this by noting the timeouts in struct rxrpc_call when the call is
created. The timer will be started when the first packet is transmitted.
It shouldn't be possible to trigger this directly from userspace through
AF_RXRPC as sendmsg() will return EBUSY if the call is in the
waiting-for-conn state if it dropped out of the wait due to a signal.
Fixes: 9d35d880e0e4 ("rxrpc: Move client call connection to the I/O thread")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sendmsg() creates an rxrpc call, it queues it to wait for a connection
and channel to be assigned and then waits before it can start shovelling
data as the encrypted DATA packet content includes a summary of the
connection parameters.
However, sendmsg() may get interrupted before a connection gets assigned
and further sendmsg() calls will fail with EBUSY until an assignment is
made.
Fix this so that the call can at least be aborted without failing on
EBUSY. We have to be careful here as sendmsg() mustn't be allowed to start
the call timer if the call doesn't yet have a connection assigned as an
oops may follow shortly thereafter.
Fixes: 540b1c48c37a ("rxrpc: Fix deadlock between call creation and sendmsg/recvmsg")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hard call timeout is specified in the RXRPC_SET_CALL_TIMEOUT cmsg in
seconds, so fix the point at which sendmsg() applies it to the call to
convert to jiffies from seconds, not milliseconds.
Fixes: a158bdd3247b ("rxrpc: Fix timeout of a call that hasn't yet been granted a channel")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux
Pull module updates from Luis Chamberlain:
"The summary of the changes for this pull requests is:
- Song Liu's new struct module_memory replacement
- Nick Alcock's MODULE_LICENSE() removal for non-modules
- My cleanups and enhancements to reduce the areas where we vmalloc
module memory for duplicates, and the respective debug code which
proves the remaining vmalloc pressure comes from userspace.
Most of the changes have been in linux-next for quite some time except
the minor fixes I made to check if a module was already loaded prior
to allocating the final module memory with vmalloc and the respective
debug code it introduces to help clarify the issue. Although the
functional change is small it is rather safe as it can only *help*
reduce vmalloc space for duplicates and is confirmed to fix a bootup
issue with over 400 CPUs with KASAN enabled. I don't expect stable
kernels to pick up that fix as the cleanups would have also had to
have been picked up. Folks on larger CPU systems with modules will
want to just upgrade if vmalloc space has been an issue on bootup.
Given the size of this request, here's some more elaborate details:
The functional change change in this pull request is the very first
patch from Song Liu which replaces the 'struct module_layout' with a
new 'struct module_memory'. The old data structure tried to put
together all types of supported module memory types in one data
structure, the new one abstracts the differences in memory types in a
module to allow each one to provide their own set of details. This
paves the way in the future so we can deal with them in a cleaner way.
If you look at changes they also provide a nice cleanup of how we
handle these different memory areas in a module. This change has been
in linux-next since before the merge window opened for v6.3 so to
provide more than a full kernel cycle of testing. It's a good thing as
quite a bit of fixes have been found for it.
Jason Baron then made dynamic debug a first class citizen module user
by using module notifier callbacks to allocate / remove module
specific dynamic debug information.
Nick Alcock has done quite a bit of work cross-tree to remove module
license tags from things which cannot possibly be module at my request
so to:
a) help him with his longer term tooling goals which require a
deterministic evaluation if a piece a symbol code could ever be
part of a module or not. But quite recently it is has been made
clear that tooling is not the only one that would benefit.
Disambiguating symbols also helps efforts such as live patching,
kprobes and BPF, but for other reasons and R&D on this area is
active with no clear solution in sight.
b) help us inch closer to the now generally accepted long term goal
of automating all the MODULE_LICENSE() tags from SPDX license tags
In so far as a) is concerned, although module license tags are a no-op
for non-modules, tools which would want create a mapping of possible
modules can only rely on the module license tag after the commit
8b41fc4454e ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf").
Nick has been working on this *for years* and AFAICT I was the only
one to suggest two alternatives to this approach for tooling. The
complexity in one of my suggested approaches lies in that we'd need a
possible-obj-m and a could-be-module which would check if the object
being built is part of any kconfig build which could ever lead to it
being part of a module, and if so define a new define
-DPOSSIBLE_MODULE [0].
A more obvious yet theoretical approach I've suggested would be to
have a tristate in kconfig imply the same new -DPOSSIBLE_MODULE as
well but that means getting kconfig symbol names mapping to modules
always, and I don't think that's the case today. I am not aware of
Nick or anyone exploring either of these options. Quite recently Josh
Poimboeuf has pointed out that live patching, kprobes and BPF would
benefit from resolving some part of the disambiguation as well but for
other reasons. The function granularity KASLR (fgkaslr) patches were
mentioned but Joe Lawrence has clarified this effort has been dropped
with no clear solution in sight [1].
In the meantime removing module license tags from code which could
never be modules is welcomed for both objectives mentioned above. Some
developers have also welcomed these changes as it has helped clarify
when a module was never possible and they forgot to clean this up, and
so you'll see quite a bit of Nick's patches in other pull requests for
this merge window. I just picked up the stragglers after rc3. LWN has
good coverage on the motivation behind this work [2] and the typical
cross-tree issues he ran into along the way. The only concrete blocker
issue he ran into was that we should not remove the MODULE_LICENSE()
tags from files which have no SPDX tags yet, even if they can never be
modules. Nick ended up giving up on his efforts due to having to do
this vetting and backlash he ran into from folks who really did *not
understand* the core of the issue nor were providing any alternative /
guidance. I've gone through his changes and dropped the patches which
dropped the module license tags where an SPDX license tag was missing,
it only consisted of 11 drivers. To see if a pull request deals with a
file which lacks SPDX tags you can just use:
./scripts/spdxcheck.py -f \
$(git diff --name-only commid-id | xargs echo)
You'll see a core module file in this pull request for the above, but
that's not related to his changes. WE just need to add the SPDX
license tag for the kernel/module/kmod.c file in the future but it
demonstrates the effectiveness of the script.
Most of Nick's changes were spread out through different trees, and I
just picked up the slack after rc3 for the last kernel was out. Those
changes have been in linux-next for over two weeks.
The cleanups, debug code I added and final fix I added for modules
were motivated by David Hildenbrand's report of boot failing on a
systems with over 400 CPUs when KASAN was enabled due to running out
of virtual memory space. Although the functional change only consists
of 3 lines in the patch "module: avoid allocation if module is already
present and ready", proving that this was the best we can do on the
modules side took quite a bit of effort and new debug code.
The initial cleanups I did on the modules side of things has been in
linux-next since around rc3 of the last kernel, the actual final fix
for and debug code however have only been in linux-next for about a
week or so but I think it is worth getting that code in for this merge
window as it does help fix / prove / evaluate the issues reported with
larger number of CPUs. Userspace is not yet fixed as it is taking a
bit of time for folks to understand the crux of the issue and find a
proper resolution. Worst come to worst, I have a kludge-of-concept [3]
of how to make kernel_read*() calls for modules unique / converge
them, but I'm currently inclined to just see if userspace can fix this
instead"
Link: https://lore.kernel.org/all/Y/kXDqW+7d71C4wz@bombadil.infradead.org/ [0]
Link: https://lkml.kernel.org/r/025f2151-ce7c-5630-9b90-98742c97ac65@redhat.com [1]
Link: https://lwn.net/Articles/927569/ [2]
Link: https://lkml.kernel.org/r/20230414052840.1994456-3-mcgrof@kernel.org [3]
* tag 'modules-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcgrof/linux: (121 commits)
module: add debugging auto-load duplicate module support
module: stats: fix invalid_mod_bytes typo
module: remove use of uninitialized variable len
module: fix building stats for 32-bit targets
module: stats: include uapi/linux/module.h
module: avoid allocation if module is already present and ready
module: add debug stats to help identify memory pressure
module: extract patient module check into helper
modules/kmod: replace implementation with a semaphore
Change DEFINE_SEMAPHORE() to take a number argument
module: fix kmemleak annotations for non init ELF sections
module: Ignore L0 and rename is_arm_mapping_symbol()
module: Move is_arm_mapping_symbol() to module_symbol.h
module: Sync code of is_arm_mapping_symbol()
scripts/gdb: use mem instead of core_layout to get the module address
interconnect: remove module-related code
interconnect: remove MODULE_LICENSE in non-modules
zswap: remove MODULE_LICENSE in non-modules
zpool: remove MODULE_LICENSE in non-modules
x86/mm/dump_pagetables: remove MODULE_LICENSE in non-modules
...
|
|
Inside the loop in rxrpc_wait_to_be_connected() it checks call->error to
see if it should exit the loop without first checking the call state. This
is probably safe as if call->error is set, the call is dead anyway, but we
should probably wait for the call state to have been set to completion
first, lest it cause surprise on the way out.
Fix this by only accessing call->error if the call is complete. We don't
actually need to access the error inside the loop as we'll do that after.
This caused the following report:
BUG: KCSAN: data-race in rxrpc_send_data / rxrpc_set_call_completion
write to 0xffff888159cf3c50 of 4 bytes by task 25673 on cpu 1:
rxrpc_set_call_completion+0x71/0x1c0 net/rxrpc/call_state.c:22
rxrpc_send_data_packet+0xba9/0x1650 net/rxrpc/output.c:479
rxrpc_transmit_one+0x1e/0x130 net/rxrpc/output.c:714
rxrpc_decant_prepared_tx net/rxrpc/call_event.c:326 [inline]
rxrpc_transmit_some_data+0x496/0x600 net/rxrpc/call_event.c:350
rxrpc_input_call_event+0x564/0x1220 net/rxrpc/call_event.c:464
rxrpc_io_thread+0x307/0x1d80 net/rxrpc/io_thread.c:461
kthread+0x1ac/0x1e0 kernel/kthread.c:376
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:308
read to 0xffff888159cf3c50 of 4 bytes by task 25672 on cpu 0:
rxrpc_send_data+0x29e/0x1950 net/rxrpc/sendmsg.c:296
rxrpc_do_sendmsg+0xb7a/0xc20 net/rxrpc/sendmsg.c:726
rxrpc_sendmsg+0x413/0x520 net/rxrpc/af_rxrpc.c:565
sock_sendmsg_nosec net/socket.c:724 [inline]
sock_sendmsg net/socket.c:747 [inline]
____sys_sendmsg+0x375/0x4c0 net/socket.c:2501
___sys_sendmsg net/socket.c:2555 [inline]
__sys_sendmmsg+0x263/0x500 net/socket.c:2641
__do_sys_sendmmsg net/socket.c:2670 [inline]
__se_sys_sendmmsg net/socket.c:2667 [inline]
__x64_sys_sendmmsg+0x57/0x60 net/socket.c:2667
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x41/0xc0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
value changed: 0x00000000 -> 0xffffffea
Fixes: 9d35d880e0e4 ("rxrpc: Move client call connection to the I/O thread")
Reported-by: syzbot+ebc945fdb4acd72cba78@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/000000000000e7c6d205fa10a3cd@google.com/
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: Dmitry Vyukov <dvyukov@google.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: linux-fsdevel@vger.kernel.org
cc: netdev@vger.kernel.org
Link: https://lore.kernel.org/r/508133.1682427395@warthog.procyon.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
No conflicts.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When converting from ASSERTCMP to WARN_ON, the tested condition must
be inverted, which was missed for this case.
This would cause an EIO error when trying to read an rxrpc token, for
instance when trying to display tokens with AuriStor's "tokens" command.
Fixes: 84924aac08a4 ("rxrpc: Fix checker warning")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Zero-length arrays as fake flexible arrays are deprecated and we are
moving towards adopting C99 flexible-array members instead.
Transform zero-length array into flexible-array member in struct
rxrpc_ackpacket.
Address the following warnings found with GCC-13 and
-fstrict-flex-arrays=3 enabled:
net/rxrpc/call_event.c:149:38: warning: array subscript i is outside array bounds of ‘uint8_t[0]’ {aka ‘unsigned char[]’} [-Warray-bounds=]
This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [1].
Link: https://github.com/KSPP/linux/issues/21
Link: https://github.com/KSPP/linux/issues/263
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [1]
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
cc: linux-hardening@vger.kernel.org
Link: https://lore.kernel.org/r/ZAZT11n4q5bBttW0@work/
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the rxrpc call set up by afs_make_call() receives an error whilst it is
transmitting the request, there's the possibility that it may get to the
point the rxrpc call is ended (after the error_kill_call label) just as the
call is queued for async processing.
This could manifest itself as call->rxcall being seen as NULL in
afs_deliver_to_call() when it tries to lock the call.
Fix this by splitting rxrpc_kernel_end_call() into a function to shut down
an rxrpc call and a function to release the caller's reference and calling
the latter only when we get to afs_put_call().
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: kafs-testing+fedora36_64checkkafs-build-306@auristor.com
cc: Marc Dionne <marc.dionne@auristor.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: Eric Dumazet <edumazet@google.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: linux-afs@lists.infradead.org
cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fundamentally semaphores are a counted primitive, but
DEFINE_SEMAPHORE() does not expose this and explicitly creates a
binary semaphore.
Change DEFINE_SEMAPHORE() to take a number argument and use that in the
few places that open-coded it using __SEMAPHORE_INITIALIZER().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
[mcgrof: add some tribal knowledge about why some folks prefer
binary sempahores over mutexes]
Reviewed-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Reviewed-by: Davidlohr Bueso <dave@stgolabs.net>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- Add dedicated kmem_cache for typical/small skb->head, avoid having
to access struct page at kfree time, and improve memory use.
- Introduce sysctl to set default RPS configuration for new netdevs.
- Define Netlink protocol specification format which can be used to
describe messages used by each family and auto-generate parsers.
Add tools for generating kernel data structures and uAPI headers.
- Expose all net/core sysctls inside netns.
- Remove 4s sleep in netpoll if carrier is instantly detected on
boot.
- Add configurable limit of MDB entries per port, and port-vlan.
- Continue populating drop reasons throughout the stack.
- Retire a handful of legacy Qdiscs and classifiers.
Protocols:
- Support IPv4 big TCP (TSO frames larger than 64kB).
- Add IP_LOCAL_PORT_RANGE socket option, to control local port range
on socket by socket basis.
- Track and report in procfs number of MPTCP sockets used.
- Support mixing IPv4 and IPv6 flows in the in-kernel MPTCP path
manager.
- IPv6: don't check net.ipv6.route.max_size and rely on garbage
collection to free memory (similarly to IPv4).
- Support Penultimate Segment Pop (PSP) flavor in SRv6 (RFC8986).
- ICMP: add per-rate limit counters.
- Add support for user scanning requests in ieee802154.
- Remove static WEP support.
- Support minimal Wi-Fi 7 Extremely High Throughput (EHT) rate
reporting.
- WiFi 7 EHT channel puncturing support (client & AP).
BPF:
- Add a rbtree data structure following the "next-gen data structure"
precedent set by recently added linked list, that is, by using
kfunc + kptr instead of adding a new BPF map type.
- Expose XDP hints via kfuncs with initial support for RX hash and
timestamp metadata.
- Add BPF_F_NO_TUNNEL_KEY extension to bpf_skb_set_tunnel_key to
better support decap on GRE tunnel devices not operating in collect
metadata.
- Improve x86 JIT's codegen for PROBE_MEM runtime error checks.
- Remove the need for trace_printk_lock for bpf_trace_printk and
bpf_trace_vprintk helpers.
- Extend libbpf's bpf_tracing.h support for tracing arguments of
kprobes/uprobes and syscall as a special case.
- Significantly reduce the search time for module symbols by
livepatch and BPF.
- Enable cpumasks to be used as kptrs, which is useful for tracing
programs tracking which tasks end up running on which CPUs in
different time intervals.
- Add support for BPF trampoline on s390x and riscv64.
- Add capability to export the XDP features supported by the NIC.
- Add __bpf_kfunc tag for marking kernel functions as kfuncs.
- Add cgroup.memory=nobpf kernel parameter option to disable BPF
memory accounting for container environments.
Netfilter:
- Remove the CLUSTERIP target. It has been marked as obsolete for
years, and we still have WARN splats wrt races of the out-of-band
/proc interface installed by this target.
- Add 'destroy' commands to nf_tables. They are identical to the
existing 'delete' commands, but do not return an error if the
referenced object (set, chain, rule...) did not exist.
Driver API:
- Improve cpumask_local_spread() locality to help NICs set the right
IRQ affinity on AMD platforms.
- Separate C22 and C45 MDIO bus transactions more clearly.
- Introduce new DCB table to control DSCP rewrite on egress.
- Support configuration of Physical Layer Collision Avoidance (PLCA)
Reconciliation Sublayer (RS) (802.3cg-2019). Modern version of
shared medium Ethernet.
- Support for MAC Merge layer (IEEE 802.3-2018 clause 99). Allowing
preemption of low priority frames by high priority frames.
- Add support for controlling MACSec offload using netlink SET.
- Rework devlink instance refcounts to allow registration and
de-registration under the instance lock. Split the code into
multiple files, drop some of the unnecessarily granular locks and
factor out common parts of netlink operation handling.
- Add TX frame aggregation parameters (for USB drivers).
- Add a new attr TCA_EXT_WARN_MSG to report TC (offload) warning
messages with notifications for debug.
- Allow offloading of UDP NEW connections via act_ct.
- Add support for per action HW stats in TC.
- Support hardware miss to TC action (continue processing in SW from
a specific point in the action chain).
- Warn if old Wireless Extension user space interface is used with
modern cfg80211/mac80211 drivers. Do not support Wireless
Extensions for Wi-Fi 7 devices at all. Everyone should switch to
using nl80211 interface instead.
- Improve the CAN bit timing configuration. Use extack to return
error messages directly to user space, update the SJW handling,
including the definition of a new default value that will benefit
CAN-FD controllers, by increasing their oscillator tolerance.
New hardware / drivers:
- Ethernet:
- nVidia BlueField-3 support (control traffic driver)
- Ethernet support for imx93 SoCs
- Motorcomm yt8531 gigabit Ethernet PHY
- onsemi NCN26000 10BASE-T1S PHY (with support for PLCA)
- Microchip LAN8841 PHY (incl. cable diagnostics and PTP)
- Amlogic gxl MDIO mux
- WiFi:
- RealTek RTL8188EU (rtl8xxxu)
- Qualcomm Wi-Fi 7 devices (ath12k)
- CAN:
- Renesas R-Car V4H
Drivers:
- Bluetooth:
- Set Per Platform Antenna Gain (PPAG) for Intel controllers.
- Ethernet NICs:
- Intel (1G, igc):
- support TSN / Qbv / packet scheduling features of i226 model
- Intel (100G, ice):
- use GNSS subsystem instead of TTY
- multi-buffer XDP support
- extend support for GPIO pins to E823 devices
- nVidia/Mellanox:
- update the shared buffer configuration on PFC commands
- implement PTP adjphase function for HW offset control
- TC support for Geneve and GRE with VF tunnel offload
- more efficient crypto key management method
- multi-port eswitch support
- Netronome/Corigine:
- add DCB IEEE support
- support IPsec offloading for NFP3800
- Freescale/NXP (enetc):
- support XDP_REDIRECT for XDP non-linear buffers
- improve reconfig, avoid link flap and waiting for idle
- support MAC Merge layer
- Other NICs:
- sfc/ef100: add basic devlink support for ef100
- ionic: rx_push mode operation (writing descriptors via MMIO)
- bnxt: use the auxiliary bus abstraction for RDMA
- r8169: disable ASPM and reset bus in case of tx timeout
- cpsw: support QSGMII mode for J721e CPSW9G
- cpts: support pulse-per-second output
- ngbe: add an mdio bus driver
- usbnet: optimize usbnet_bh() by avoiding unnecessary queuing
- r8152: handle devices with FW with NCM support
- amd-xgbe: support 10Mbps, 2.5GbE speeds and rx-adaptation
- virtio-net: support multi buffer XDP
- virtio/vsock: replace virtio_vsock_pkt with sk_buff
- tsnep: XDP support
- Ethernet high-speed switches:
- nVidia/Mellanox (mlxsw):
- add support for latency TLV (in FW control messages)
- Microchip (sparx5):
- separate explicit and implicit traffic forwarding rules, make
the implicit rules always active
- add support for egress DSCP rewrite
- IS0 VCAP support (Ingress Classification)
- IS2 VCAP filters (protos, L3 addrs, L4 ports, flags, ToS
etc.)
- ES2 VCAP support (Egress Access Control)
- support for Per-Stream Filtering and Policing (802.1Q,
8.6.5.1)
- Ethernet embedded switches:
- Marvell (mv88e6xxx):
- add MAB (port auth) offload support
- enable PTP receive for mv88e6390
- NXP (ocelot):
- support MAC Merge layer
- support for the the vsc7512 internal copper phys
- Microchip:
- lan9303: convert to PHYLINK
- lan966x: support TC flower filter statistics
- lan937x: PTP support for KSZ9563/KSZ8563 and LAN937x
- lan937x: support Credit Based Shaper configuration
- ksz9477: support Energy Efficient Ethernet
- other:
- qca8k: convert to regmap read/write API, use bulk operations
- rswitch: Improve TX timestamp accuracy
- Intel WiFi (iwlwifi):
- EHT (Wi-Fi 7) rate reporting
- STEP equalizer support: transfer some STEP (connection to radio
on platforms with integrated wifi) related parameters from the
BIOS to the firmware.
- Qualcomm 802.11ax WiFi (ath11k):
- IPQ5018 support
- Fine Timing Measurement (FTM) responder role support
- channel 177 support
- MediaTek WiFi (mt76):
- per-PHY LED support
- mt7996: EHT (Wi-Fi 7) support
- Wireless Ethernet Dispatch (WED) reset support
- switch to using page pool allocator
- RealTek WiFi (rtw89):
- support new version of Bluetooth co-existance
- Mobile:
- rmnet: support TX aggregation"
* tag 'net-next-6.3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1872 commits)
page_pool: add a comment explaining the fragment counter usage
net: ethtool: fix __ethtool_dev_mm_supported() implementation
ethtool: pse-pd: Fix double word in comments
xsk: add linux/vmalloc.h to xsk.c
sefltests: netdevsim: wait for devlink instance after netns removal
selftest: fib_tests: Always cleanup before exit
net/mlx5e: Align IPsec ASO result memory to be as required by hardware
net/mlx5e: TC, Set CT miss to the specific ct action instance
net/mlx5e: Rename CHAIN_TO_REG to MAPPED_OBJ_TO_REG
net/mlx5: Refactor tc miss handling to a single function
net/mlx5: Kconfig: Make tc offload depend on tc skb extension
net/sched: flower: Support hardware miss to tc action
net/sched: flower: Move filter handle initialization earlier
net/sched: cls_api: Support hardware miss to tc action
net/sched: Rename user cookie and act cookie
sfc: fix builds without CONFIG_RTC_LIB
sfc: clean up some inconsistent indentings
net/mlx4_en: Introduce flexible array to silence overflow warning
net: lan966x: Fix possible deadlock inside PTP
net/ulp: Remove redundant ->clone() test in inet_clone_ulp().
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardening updates from Kees Cook:
"Beyond some specific LoadPin, UBSAN, and fortify features, there are
other fixes scattered around in various subsystems where maintainers
were okay with me carrying them in my tree or were non-responsive but
the patches were reviewed by others:
- Replace 0-length and 1-element arrays with flexible arrays in
various subsystems (Paulo Miguel Almeida, Stephen Rothwell, Kees
Cook)
- randstruct: Disable Clang 15 support (Eric Biggers)
- GCC plugins: Drop -std=gnu++11 flag (Sam James)
- strpbrk(): Refactor to use strchr() (Andy Shevchenko)
- LoadPin LSM: Allow root filesystem switching when non-enforcing
- fortify: Use dynamic object size hints when available
- ext4: Fix CFI function prototype mismatch
- Nouveau: Fix DP buffer size arguments
- hisilicon: Wipe entire crypto DMA pool on error
- coda: Fully allocate sig_inputArgs
- UBSAN: Improve arm64 trap code reporting
- copy_struct_from_user(): Add minimum bounds check on kernel buffer
size"
* tag 'hardening-v6.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
randstruct: disable Clang 15 support
uaccess: Add minimum bounds check on kernel buffer size
arm64: Support Clang UBSAN trap codes for better reporting
coda: Avoid partial allocation of sig_inputArgs
gcc-plugins: drop -std=gnu++11 to fix GCC 13 build
lib/string: Use strchr() in strpbrk()
crypto: hisilicon: Wipe entire pool on error
net/i40e: Replace 0-length array with flexible array
io_uring: Replace 0-length array with flexible array
ext4: Fix function prototype mismatch for ext4_feat_ktype
i915/gvt: Replace one-element array with flexible-array member
drm/nouveau/disp: Fix nvif_outp_acquire_dp() argument size
LoadPin: Allow filesystem switch when not enforcing
LoadPin: Move pin reporting cleanly out of locking
LoadPin: Refactor sysctl initialization
LoadPin: Refactor read-only check into a helper
ARM: ixp4xx: Replace 0-length arrays with flexible arrays
fortify: Use __builtin_dynamic_object_size() when available
rxrpc: replace zero-lenth array with DECLARE_FLEX_ARRAY() helper
|
|
Fix three cases of overproduction of wakeups:
(1) rxrpc_input_split_jumbo() conditionally notifies the app that there's
data for recvmsg() to collect if it queues some data - and then its
only caller, rxrpc_input_data(), goes and wakes up recvmsg() anyway.
Fix the rxrpc_input_data() to only do the wakeup in failure cases.
(2) If a DATA packet is received for a call by the I/O thread whilst
recvmsg() is busy draining the call's rx queue in the app thread, the
call will left on the recvmsg() queue for recvmsg() to pick up, even
though there isn't any data on it.
This can cause an unexpected recvmsg() with a 0 return and no MSG_EOR
set after the reply has been posted to a service call.
Fix this by discarding pending calls from the recvmsg() queue that
don't need servicing yet.
(3) Not-yet-completed calls get requeued after having data read from them,
even if they have no data to read.
Fix this by only requeuing them if they have data waiting on them; if
they don't, the I/O thread will requeue them when data arrives or they
fail.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
Link: https://lore.kernel.org/r/3386149.1676497685@warthog.procyon.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
rxrpc_recvmsg_data() schedules an ACK to be transmitted every time at least
two packets have been consumed and any time it runs out of data and would
return -EAGAIN to the caller. Both events may occur within a single loop,
however, and if the I/O thread is quick enough it may send duplicate ACKs.
The ACKs are sent to inform the peer that more space has been made in the
local Rx window, but the I/O thread is going to send an ACK every couple of
DATA packets anyway, so we end up sending a lot more ACKs than we really
need to.
So reduce the rate at which recvmsg() schedules ACKs, such that if the I/O
thread sends ACKs at its normal faster rate, recvmsg() won't actually
schedule ACKs until the Rx flow stops (call->rx_consumed is cleared any
time we transmit an ACK for that call, resetting the counter used by
recvmsg).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Log ack.rwind in the rxrpc_tx_ack tracepoint. This value is useful to see
as it represents flow-control information to the peer.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
If an rxrpc call is given a poke, it will get woken up unconditionally,
even if there's already a poke pending (for which there will have been a
wake) or if the call refcount has gone to 0.
Fix this by only waking the call if it is still referenced and if it
doesn't already have a poke pending.
Fixes: 15f661dc95da ("rxrpc: Implement a mechanism to send an event notification to a call")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Use consume_skb() rather than kfree_skb_reason().
Reported-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Use the bvec_set_page helper to initialize a bvec.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/20230203150634.3199647-21-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Now that the bundle->channel_lock has been eliminated, we don't need the
dummy service bundle anymore. It's purpose was purely to provide the
channel_lock for service connections.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Set a reason when freeing a packet that has been consumed such that
dropwatch doesn't complain that it has been dropped.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
We no longer need local->defrag_sem as all DATA packet transmission is now
done from one thread, so remove it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
call->tx_buffer is now only accessed within the I/O thread (->tx_sendmsg is
the way sendmsg passes packets to the I/O thread) so there's no need to
lock around it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Now that general ACK transmission is done from the same thread as incoming
DATA packet wrangling, there's no possibility that the SACK table will be
being updated by the latter whilst the former is trying to copy it to an
ACK.
This means that we can safely rotate the SACK table whilst updating it
without having to take a lock, rather than keeping all the bits inside it
in fixed place and copying and then rotating it in the transmitter.
Therefore, simplify SACK handing by keeping track of starting point in the
ring and rotate slots down as we consume them.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
call->ackr_window doesn't need to be atomic as ACK generation and ACK
transmission are now done in the same thread, so drop the atomic64 handling
and split it into two separate members.
Similarly, call->ackr_nr_unacked doesn't need to be atomic now either.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
When doing a call that has a single transmitted data packet and a massive
amount of received data packets, we only ping for one RTT sample, which
means we don't get a good reading on it.
Fix this by converting occasional IDLE ACKs into PING ACKs to elicit a
response.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
If CONFIG_AF_RXRPC_DEBUG_RX_DELAY=y, then a delay is injected between
packets and errors being received and them being made available to the
processing code, thereby allowing the RTT to be artificially increased.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Convert call->recvmsg_lock to a spinlock as it's only ever write-locked.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Fix a trace string to indicate that it's discarding the local endpoint for
a preallocated peer, not a preallocated connection.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Fix rxrpc_connect_call() to return -ENOMEM rather than 0 if it fails to
look up a peer.
This generated a smatch warning:
net/rxrpc/call_object.c:303 rxrpc_connect_call() warn: missing error code 'ret'
I think this also fixes a syzbot-found bug:
rxrpc: Assertion failed - 1(0x1) == 11(0xb) is false
------------[ cut here ]------------
kernel BUG at net/rxrpc/call_object.c:645!
where the call being put is in the wrong state - as would be the case if we
failed to clear up correctly after the error in rxrpc_connect_call().
Fixes: 9d35d880e0e4 ("rxrpc: Move client call connection to the I/O thread")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Reported-and-tested-by: syzbot+4bb6356bb29d6299360e@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/202301111153.9eZRYLf1-lkp@intel.com/
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/2438405.1673460435@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
An incoming call can race with rxrpc socket destruction, leading to a
leaked call. This may result in an oops when the call timer eventually
expires:
BUG: kernel NULL pointer dereference, address: 0000000000000874
RIP: 0010:_raw_spin_lock_irqsave+0x2a/0x50
Call Trace:
<IRQ>
try_to_wake_up+0x59/0x550
? __local_bh_enable_ip+0x37/0x80
? rxrpc_poke_call+0x52/0x110 [rxrpc]
? rxrpc_poke_call+0x110/0x110 [rxrpc]
? rxrpc_poke_call+0x110/0x110 [rxrpc]
call_timer_fn+0x24/0x120
with a warning in the kernel log looking something like:
rxrpc: Call 00000000ba5e571a still in use (1,SvAwtACK,1061d,0)!
incurred during rmmod of rxrpc. The 1061d is the call flags:
RECVMSG_READ_ALL, RX_HEARD, BEGAN_RX_TIMER, RX_LAST, EXPOSED,
IS_SERVICE, RELEASED
but no DISCONNECTED flag (0x800), so it's an incoming (service) call and
it's still connected.
The race appears to be that:
(1) rxrpc_new_incoming_call() consults the service struct, checks sk_state
and allocates a call - then pauses, possibly for an interrupt.
(2) rxrpc_release_sock() sets RXRPC_CLOSE, nulls the service pointer,
discards the prealloc and releases all calls attached to the socket.
(3) rxrpc_new_incoming_call() resumes, launching the new call, including
its timer and attaching it to the socket.
Fix this by read-locking local->services_lock to access the AF_RXRPC socket
providing the service rather than RCU in rxrpc_new_incoming_call().
There's no real need to use RCU here as local->services_lock is only
write-locked by the socket side in two places: when binding and when
shutting down.
Fixes: 5e6ef4f1017c ("rxrpc: Make the I/O thread take over the call and local processor work")
Reported-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-afs@lists.infradead.org
|
|
Move the connection setup of client calls to the I/O thread so that a whole
load of locking and barrierage can be eliminated. This necessitates the
app thread waiting for connection to complete before it can begin
encrypting data.
This also completes the fix for a race that exists between call connection
and call disconnection whereby the data transmission code adds the call to
the peer error distribution list after the call has been disconnected (say
by the rxrpc socket getting closed).
The fix is to complete the process of moving call connection, data
transmission and call disconnection into the I/O thread and thus forcibly
serialising them.
Note that the issue may predate the overhaul to an I/O thread model that
were included in the merge window for v6.2, but the timing is very much
changed by the change given below.
Fixes: cf37b5987508 ("rxrpc: Move DATA transmission into call processor work item")
Reported-by: syzbot+c22650d2844392afdcfd@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Move the management of the client connection cache to the I/O thread rather
than managing it from the namespace as an aggregate across all the local
endpoints within the namespace.
This will allow a load of locking to be got rid of in a future patch as
only the I/O thread will be looking at the this.
The downside is that the total number of cached connections on the system
can get higher because the limit is now per-local rather than per-netns.
We can, however, keep the number of client conns in use across the entire
netfs and use that to reduce the expiration time of idle connection.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
All the setters of call->state are now in the I/O thread and thus the state
lock is now unnecessary.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Move the call state changes that are made in rxrpc_recvmsg() to the I/O
thread. This means that, thenceforth, only the I/O thread does this and
the call state lock can be removed.
This requires the Rx phase to be ended when the last packet is received,
not when it is processed.
Since this now changes the rxrpc call state to SUCCEEDED before we've
consumed all the data from it, rxrpc_kernel_check_life() mustn't say the
call is dead until the recvmsg queue is empty (unless the call has failed).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Move all the call state changes that are made in rxrpc_sendmsg() to the I/O
thread. This is a step towards removing the call state lock.
This requires the switch to the RXRPC_CALL_CLIENT_AWAIT_REPLY and
RXRPC_CALL_SERVER_SEND_REPLY states to be done when the last packet is
decanted from ->tx_sendmsg to ->tx_buffer in the I/O thread, not when it is
added to ->tx_sendmsg by sendmsg().
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Wrap accesses to get the state of a call from outside of the I/O thread in
a single place so that the barrier needed to order wrt the error code and
abort code is in just that place.
Also use a barrier when setting the call state and again when reading the
call state such that the auxiliary completion info (error code, abort code)
can be read without taking a read lock on the call state lock.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Split out the functions that change the state of an rxrpc call into their
own file. The idea being to remove anything to do with changing the state
of a call directly from the rxrpc sendmsg() and recvmsg() paths and have
all that done in the I/O thread only, with the ultimate aim of removing the
state lock entirely. Moving the code out of sendmsg.c and recvmsg.c makes
that easier to manage.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Use the information now stored in struct rxrpc_call to configure the
connection bundle and thence the connection, rather than using the
rxrpc_conn_parameters struct.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Offload the completion of the challenge/response cycle on a service
connection to the I/O thread. After the RESPONSE packet has been
successfully decrypted and verified by the work queue, offloading the
changing of the call states to the I/O thread makes iteration over the
conn's channel list simpler.
Do this by marking the RESPONSE skbuff and putting it onto the receive
queue for the I/O thread to collect. We put it on the front of the queue
as we've already received the packet for it.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Make the set of connection IDs per local endpoint so that endpoints don't
cause each other's connections to get dismissed.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Tidy up the abort generation infrastructure in the following ways:
(1) Create an enum and string mapping table to list the reasons an abort
might be generated in tracing.
(2) Replace the 3-char string with the values from (1) in the places that
use that to log the abort source. This gets rid of a memcpy() in the
tracepoint.
(3) Subsume the rxrpc_rx_eproto tracepoint with the rxrpc_abort tracepoint
and use values from (1) to indicate the trace reason.
(4) Always make a call to an abort function at the point of the abort
rather than stashing the values into variables and using goto to get
to a place where it reported. The C optimiser will collapse the calls
together as appropriate. The abort functions return a value that can
be returned directly if appropriate.
Note that this extends into afs also at the points where that generates an
abort. To aid with this, the afs sources need to #define
RXRPC_TRACE_ONLY_DEFINE_ENUMS before including the rxrpc tracing header
because they don't have access to the rxrpc internal structures that some
of the tracepoints make use of.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Clean up connection abort, using the connection state_lock to gate access
to change that state, and use an rxrpc_call_completion value to indicate
the difference between local and remote aborts as these can be pasted
directly into the call state.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Provide a means by which an event notification can be sent to a connection
through such that the I/O thread can pick it up and handle it rather than
doing it in a separate workqueue.
This is then used to move the deferred final ACK of a call into the I/O
thread rather than a separate work queue as part of the drive to do all
transmission from the I/O thread.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Only perform call disconnection in the I/O thread to reduce the locking
requirement.
This is the first part of a fix for a race that exists between call
connection and call disconnection whereby the data transmission code adds
the call to the peer error distribution list after the call has been
disconnected (say by the rxrpc socket getting closed).
The fix is to complete the process of moving call connection, data
transmission and call disconnection into the I/O thread and thus forcibly
serialising them.
Note that the issue may predate the overhaul to an I/O thread model that
were included in the merge window for v6.2, but the timing is very much
changed by the change given below.
Fixes: cf37b5987508 ("rxrpc: Move DATA transmission into call processor work item")
Reported-by: syzbot+c22650d2844392afdcfd@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Only set the abort call completion state in the I/O thread and only
transmit ABORT packets from there. rxrpc_abort_call() can then be made to
actually send the packet.
Further, ABORT packets should only be sent if the call has been exposed to
the network (ie. at least one attempted DATA transmission has occurred for
it).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Call the rxrpc_conn_retransmit_call() directly from rxrpc_input_packet()
rather than calling it via connection event handling.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Make the local endpoint and it's I/O thread hold a reference on a connected
call until that call is disconnected. Without this, we're reliant on
either the AF_RXRPC socket to hold a ref (which is dropped when the call is
released) or a queued work item to hold a ref (the work item is being
replaced with the I/O thread).
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
Stash the network namespace pointer in the rxrpc_local struct in addition
to a pointer to the rxrpc-specific net namespace info. Use this to remove
some places where the socket is passed as a parameter.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Marc Dionne <marc.dionne@auristor.com>
cc: linux-afs@lists.infradead.org
|
|
0-length arrays are deprecated, and cause problems with bounds checking.
Replace with a flexible array:
In file included from include/linux/string.h:253,
from include/linux/bitmap.h:11,
from include/linux/cpumask.h:12,
from arch/x86/include/asm/paravirt.h:17,
from arch/x86/include/asm/cpuid.h:62,
from arch/x86/include/asm/processor.h:19,
from arch/x86/include/asm/cpufeature.h:5,
from arch/x86/include/asm/thread_info.h:53,
from include/linux/thread_info.h:60,
from arch/x86/include/asm/preempt.h:9,
from include/linux/preempt.h:78,
from include/linux/percpu.h:6,
from include/linux/prandom.h:13,
from include/linux/random.h:153,
from include/linux/net.h:18,
from net/rxrpc/output.c:10:
In function 'fortify_memcpy_chk',
inlined from 'rxrpc_fill_out_ack' at net/rxrpc/output.c:158:2:
include/linux/fortify-string.h:520:25: error: call to '__write_overflow_field' declared with attribute warning: detected write beyond size of field (1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
520 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Link: https://lore.kernel.org/linux-next/20230105132535.0d65378f@canb.auug.org.au/
Cc: David Howells <dhowells@redhat.com>
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-afs@lists.infradead.org
Cc: netdev@vger.kernel.org
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kees Cook <keescook@chromium.org>
|
