| Age | Commit message (Collapse) | Author |
|---|
|
Implement set_qos_map() handler for mac80211 to enable QoS mapping
functionality.
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This allows QoS mapping from external networks to be implemented as
defined in IEEE Std 802.11-2012, 10.24.9. APs can use this to advertise
DSCP ranges and exceptions for mapping frames to a specific UP over
Wi-Fi.
The payload of the QoS Map Set element (IEEE Std 802.11-2012, 8.4.2.97)
is sent to the driver through the new NL80211_ATTR_QOS_MAP attribute to
configure the local behavior either on the AP (based on local
configuration) or on a station (based on information received from the
AP).
Signed-off-by: Kyeyoon Park <kyeyoonp@qca.qualcomm.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add routines to
- maintain a PS mode for each peer and a non-peer PS mode
- indicate own PS mode in transmitted frames
- track neighbor STAs power modes
- buffer frames when neighbors are in PS mode
- add TIM and Awake Window IE to beacons
- release frames in Mesh Peer Service Periods
Add local_pm to sta_info to represent the link-specific power
mode at this station towards the remote station. When a peer
link is established, use the default power mode stored in mesh
config. Update the PS status if the peering status of a neighbor
changes.
Maintain a mesh power mode for non-peer mesh STAs. Set the
non-peer power mode to active mode during peering. Authenticated
mesh peering is currently not working when either node is
configured to be in power save mode.
Indicate the current power mode in transmitted frames. Use QoS
Nulls to indicate mesh power mode transitions.
For performance reasons, calls to the function setting the frame
flags are placed in HWMP routing routines, as there the STA
pointer is already available.
Add peer_pm to sta_info to represent the peer's link-specific
power mode towards the local station. Add nonpeer_pm to
represent the peer's power mode towards all non-peer stations.
Track power modes based on received frames.
Add the ps_data structure to ieee80211_if_mesh (for TIM map, PS
neighbor counter and group-addressed frame buffer).
Set WLAN_STA_PS flag for STA in PS mode to use the unicast frame
buffering routines in the tx path. Update num_sta_ps to buffer
and release group-addressed frames after DTIM beacons.
Announce the awake window duration in beacons if in light or
deep sleep mode towards any peer or non-peer. Create a TIM IE
similarly to AP mode and add it to mesh beacons. Parse received
Awake Window IEs and check TIM IEs for buffered frames.
Release frames towards peers in mesh Peer Service Periods. Use
the corresponding trigger frames and monitor the MPSP status.
Append a QoS Null as trigger frame if neccessary to properly end
the MPSP. Currently, in HT channels MPSPs behave imperfectly and
show large delay spikes and frame losses.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Return early if not a QoS Data frame.
Give proper documentation.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Save and configure the wmm_acm per sdata, rather than
per hardware.
If wmm_acm is saved per hardware when running two
interfaces simultaneously on the same hardware one
interface's wmm policy will be affected by the other
interface.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When comparing hw->queues to determine if the
device is QoS capable, use IEEE80211_NUM_ACS
instead of just 4.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When we get more hardware queues, we'll still want
to only have netdev queues per AC, so set it up in
that way. If the hardware doesn't support QoS (by
not supporting at least 4 queues) the netdevs get
a single queue only (this is no change in behavior
as there are no drivers with 2 or 3 queues today.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There's no reason for it to not be static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We can't rely on ieee80211_select_queue() to do its job at this point
since the skb->protocol is not yet known. Instead, factor out and reuse
the queue mapping logic for injected frames.
Also, to mitigate congestion, forwarded frames should be dropped if the
outgoing queue was stopped. This was not correctly implemented as we
were not checking the right queue. Furthermore, we were dropping frames
that had arrived to their destination if that queue was stopped.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch contains the processing changes in mac80211.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This feature has been superseded by the NoAck per Queue feature.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
We only need to set the skb queue twice:
1. by the netdev, on local TX.
2. when forwarding a mesh frame.
We only need to set the qos header twice:
1. by mac80211, on local TX.
2. when putting a frame on the mpath->frame_queue
We also don't need the RA in order to set the proper queue mapping since
all mesh STAs are QoS, indicate this and do it once when the frame is
received. Also fixes an issue where the QoS header and queue mapping was not
set for unicast forwarded frames.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Previously QoS multicast frames had the Normal Acknowledgment QoS
control bits set. This would cause broadcast frames to be discarded by
peers with which we have a BA session, since their sequence number would
fall outside the allowed range. Set No Ack QoS control bits on multicast
QoS frames and filter these in de-aggregation code.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
v2: Use proper QoS Ack Policy ctl field mask (Christian)
v3: Clean up conditional (Johannes)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Janusz reported that the EOSP bit in mac80211 was
getting cleared all the time. I had not found this
since I tested uAPSD with a device that always set
the bit itself. Preserve the bit when building the
QoS header.
Reported-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Tested-by: Janusz Dziedzic <janusz.dziedzic@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Per sec 7.1.3.5 of draft 12.0 of 802.11s, mesh frames indicate the
presence of the mesh control header in their QoS header.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In order to support QoS in mesh, we need to assign queue mapping only
after the next hop has been resolved, both for forwarded and locally
originated frames. Also, now that this is fixed, remove the XXX comment
in ieee80211_select_queue().
Also, V-Shy Ho reported that the queue mapping was not being applied to
the forwarded frame (fwd_skb instead of skb). Fixed that as well.
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Move all that mac80211 has into the generic
ieee80211.h header file and use them. At the
same time move them from mask+shift to just
bits and rename them for consistent names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There's a redundant rcu_read_lock/unlock pair, a
redundant variable, and a few redundant accesses
to the 1d_to_ac array. Fix this to make the code
neater and easier to follow.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In many places we've just hardcoded the
AC numbers -- which is a relic from the
original mac80211 (d80211). Add constants
for them so we know what we're talking
about.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since I removed the master netdev, we've been
keeping internal queues only, and even before
that we never told the networking stack above
the virtual interfaces about congestion. This
means that packets are queued in mac80211 and
the upper layers never know, possibly leading
to memory exhaustion and other problems.
This patch makes all interfaces multiqueue and
uses ndo_select_queue to put the packets into
queues per AC. Additionally, when the driver
stops a queue, we now stop all corresponding
queues for the virtual interfaces as well.
The injection case will use VO by default for
non-data frames, and BE for data frames, but
downgrade any data frames according to ACM. It
needs to be fleshed out in the future to allow
chosing the queue/AC in radiotap.
Reported-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.32]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
In order to handle powersave frames properly we had needed
to pass these out to the device queues again, and introduce
the skb->requeue bit. This, however, also has unnecessary
overhead by needing to 'clean up' already tried frames, and
this clean-up code is also buggy when software encryption
is used.
Instead of sending the frames via the master netdev queue
again, simply put them into the pending queue. This also
fixes a problem where frames for that particular station
could be reordered when some were still on the software
queues and older ones are re-injected into the software
queue after them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
There's this internal wifi_wme_noack_test variable that
we use to set the QoS control if set. For one, it is
unlikely that it is set. Secondly, if set it needs to
influence the IEEE80211_TX_CTL_NO_ACK TX control flag,
and finally we should also be able to set it at all, so
make it available in debugfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Incorrect local->wmm_acm bits were set for AC_BK and AC_BE. Fix this
and add some comments to make it easier to understand the AC-to-UP(pair)
mapping. Set the wmm_acm bits (and show WMM debug) even if the driver
does not implement conf_tx() handler.
In addition, fix the ACM-based AC downgrade code to not use the
highest priority in error cases. We need to break the loop to get the
correct AC_BK value (3) instead of returning 0 (which would indicate
AC_VO). The comment here was not really very useful either, so let's
provide somewhat more helpful description of the situation.
Since it is very unlikely that the ACM flag would be set for AC_BK and
AC_BE, these bugs are not likely to be seen in real life networks.
Anyway, better do these things correctly should someone really use
silly AP configuration (and to pass some functionality tests, too).
Remove the TODO comment about handling ACM. Downgrading AC is
perfectly valid mechanism for ACM. Eventually, we may add support for
WMM-AC and send a request for a TS, but anyway, that functionality
won't be here at the location of this TODO comment.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Hardware with AMPDU queues currently has broken aggregation.
This patch fixes it by making all A-MPDUs go over the regular AC queues,
but keeping track of the hardware queues in mac80211. As a first rough
version, it actually stops the AC queue for extended periods of time,
which can be removed by adding buffering internal to mac80211, but is
currently not a huge problem because people rarely use multiple TIDs
that are in the same AC (and iwlwifi currently doesn't operate as AP).
This is a short-term fix, my current medium-term plan, which I hope to
execute soon as well, but am not sure can finish before .30, looks like
this:
1) rework the internal queuing layer in mac80211 that we use for
fragments if the driver stopped queue in the middle of a fragmented
frame to be able to queue more frames at once (rather than just a
single frame with its fragments)
2) instead of stopping the entire AC queue, queue up the frames in a
per-station/per-TID queue during aggregation session initiation,
when the session has come up take all those frames and put them
onto the queue from 1)
3) push the ampdu queue layer abstraction this patch introduces in
mac80211 into the driver, and remove the virtual queue stuff from
mac80211 again
This plan will probably also affect ath9k in that mac80211 queues the
frames instead of passing them down, even when there are no ampdu queues.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Wireless HW without any dedicated queues for aggregation
do not need the ampdu_queues mechanism present right now
in mac80211. Since mac80211 is still incomplete wrt TX MQ
changes, do not allow aggregation sessions for drivers that
set ampdu_queues.
This is only an interim hack until Intel fixes the requeue issue.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Also remove a few stray DECLARE_MAC_BUF that were no longer
used at all.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In "mac80211: make master iface not wireless" I accidentally
forgot to include these changes ... leading to the expected
BUG_ON errors.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes mac80211 to share some more data about
stations with drivers. Should help iwlwifi and ath9k when
they get around to updating, and might also help with
implementing rate control algorithms without internals.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Bit 4-5 of DSCP should not be considered by classify_d1. The
802.11 QoS Priority field is only depending on the precedence level.
Signed-off-by: Daniel Wagner <wagi@monom.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
qdisc_root_lock() is only %100 safe to use when the RTNL
semaphore is held.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes mac80211 to not use the skb->cb over the queue step
from virtual interfaces to the master. The patch also, for now,
disables aggregation because that would still require requeuing,
will fix that in a separate patch. There are two other places (software
requeue and powersaving stations) where requeue can happen, but that is
not currently used by any drivers/not possible to use respectively.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can simply use the qdisc->q.lock for all of the
qdisc tree synchronization.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only behavior change is that we do not drop packets under any
circumstances. If that is absolutely needed, we could easily add it
back.
With cleanups and help from Johannes Berg.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc_netdev_mq() now allocates an array of netdev_queue
structures for TX, based upon the queue_count argument.
Furthermore, all accesses to the TX queues are now vectored
through the netdev_get_tx_queue() and netdev_for_each_tx_queue()
interfaces. This makes it easy to grep the tree for all
things that want to get to a TX queue of a net device.
Problem spots which are not really multiqueue aware yet, and
only work with one queue, can easily be spotted by grepping
for all netdev_get_tx_queue() calls that pass in a zero index.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now qdisc, qdisc_sleeping, and qdisc_list also live there.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lock is now an attribute of the device queue.
One thing to notice is that "suspicious" places
emerge which will need specific training about
multiple queue handling. They are so marked with
explicit "netdev->rx_queue" and "netdev->tx_queue"
references.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It can be obtained via the netdev_queue. So create a helper routine,
qdisc_dev(), to make the transformations nicer looking.
Now, qdisc_alloc() now no longer needs a net_device pointer argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A netdev_queue is an entity managed by a qdisc.
Currently there is one RX and one TX queue, and a netdev_queue merely
contains a backpointer to the net_device.
The Qdisc struct is augmented with a netdev_queue pointer as well.
Eventually the 'dev' Qdisc member will go away and we will have the
resulting hierarchy:
net_device --> netdev_queue --> Qdisc
Also, qdisc_alloc() and qdisc_create_dflt() now take a netdev_queue
pointer argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Also remove the WLAN_IS_QOS_DATA inline after removing the last
two users. This starts moving away from using rx->fc to using
the header frame_control directly.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This patch removes useless tid assignment for management and control frames
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
Documentation/feature-removal-schedule.txt
drivers/net/wan/hdlc_fr.c
drivers/net/wireless/iwlwifi/iwl-4965.c
drivers/net/wireless/iwlwifi/iwl3945-base.c
|
|
This patch reworks the mac80211 debug settings making them more focused
and adding help text for those that didn't have one. It also removes a
number of printks that can be triggered remotely and add no value, e.g.
"too short deauthentication frame received - ignoring".
If somebody really needs to debug that they should just add a monitor
interface and look at the frames in wireshark.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Pass double tcf_proto pointers to tcf_destroy_chain() to make it
clear the start of the filter list for more consistency.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
drivers/net/wireless/rt2x00/Kconfig
drivers/net/wireless/rt2x00/rt2x00usb.c
net/sctp/protocol.c
|
|
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
