| Age | Commit message (Collapse) | Author |
|---|
|
When peering is in userspace, some implementations may want to control
which peers are accepted based on RSSI in addition to the information
elements being sent today. Add signal level so that info is available
to clients.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table. Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The Connected to Mesh Gate subfield (802.11-2016 9.4.2.98.7) in the Mesh
Formation Info field is currently unset. This field may be useful in
determining which MBSSes to join or which mesh STAs to peer with.
If this mesh STA is a gate, by having turned on mesh gate announcements,
or if we have a path to one (e.g. by having received RANNs) then set this
bit to 1.
Signed-off-by: Bob Copeland <bobcopeland@fb.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With newer VHT implementations, it's necessary to look at the
HT operation's CCFS2 field to identify the actual bandwidth
used.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With drivers implementing rate control in driver or firmware
rate_control_send_low() may not get called, and thus the
driver needs to know about changes in the multicast rate.
Add and use a new BSS change flag for this.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mesh TTL offset in Mesh Channel Switch Parameters element depends on
not only Secondary Channel Offset element, but also affected by
HT Control field and Wide Bandwidth Channel Switch element.
So use element structure to manipulate mesh channel swich param IE
after removing its constant attribution to correct the miscalculation.
Signed-off-by: Peter Oh <peter.oh@bowerswilkins.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in some cases I replaced "fall through on else" and
"otherwise fall through" comments with just a "fall through" comment,
which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This was created using the following spatch:
@find@
type S;
expression M, M2;
position p;
@@
offsetof(S, M) + sizeof(M2)@p
@script:python@
m << find.M;
m2 << find.M2;
@@
if not m2.endswith('-> ' + m):
cocci.include_match(False)
@change@
type find.S;
expression find.M, find.M2;
position find.p;
@@
-offsetof(S, M) + sizeof(M2)@p
+offsetofend(S, M)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This pattern was introduced a number of times in mac80211 just now,
and since it's present in a number of other places it makes sense
to add a little helper for it.
This just adds the helper and transforms the mac80211 code, a later
patch will transform other places.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To support HT and VHT CSA, beacons and action frames must include the
corresponding IEs.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[make ieee80211_ie_build_wide_bw_cs() return void]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If userspace has flagged support for DFS earlier, then we can follow CSA
to DFS channels. So instead of rejecting the switch, allow it to happen
if the flag has been set during mesh setup.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Clear the csa_ie in ieee80211_parse_ch_switch_ie() where the data
is filled in, rather than in each caller.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the Mesh Channel Switch Parameters (8.4.2.105) the reason is specified
to WLAN_REASON_MESH_CHAN_REGULATORY in the case that a regulatory
limitation was the cause for the switch. This means another station
detected a radar event.
Mark the channel as unusable if this happens.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
[sw: style cleanup, rebase]
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
[<bf77272c>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211]))
[<bf73cc50>] (nl80211_new_station [cfg80211])
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On some practical cases, it is useful to drop new node in the distance.
Because mesh metric is calculated with hop count and without RSSI
information, a node far from local peer and near to destination node
could be used as best path.
For example, the nodes are located in linear. Distance of 0 - 1 and
1 - 2 and 2 - 3 is 20meters. 0 to 3 signal is very weak.
0 --- 1 --- 2 --- 3
Though most robust path from 0 to 3 is 0 -> 1 -> 2 -> 3,
unfortunately, node 0 could recognize node 3 as neighbor. Then node 3
could be next of node 0. This patch aims to avoid such a case.
[Johannes:]
Dropping the node entirely isn't ideal, but at least with encryption
there will be a limit on # of keys the hardware can deal with, and
there might also be a limit on the number of stations it supports.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Fix typos and add the following to the scripts/spelling.txt:
swith||switch
swithable||switchable
swithed||switched
swithing||switching
While we are here, fix the "update" to "updates" in the touched hunk in
drivers/net/wireless/marvell/mwifiex/wmm.c.
Link: http://lkml.kernel.org/r/1481573103-11329-2-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The conflict was an interaction between a bug fix in the
netvsc driver in 'net' and an optimization of the RX path
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function ieee80211_ie_split_vendor doesn't return 0 on errors. Instead
it returns any offset < ielen when WLAN_EID_VENDOR_SPECIFIC is found. The
return value in mesh_add_vendor_ies must therefore be checked against
ifmsh->ie_len and not 0. Otherwise all ifmsh->ie starting with
WLAN_EID_VENDOR_SPECIFIC will be rejected.
Fixes: 082ebb0c258d ("mac80211: fix mesh beacon format")
Signed-off-by: Thorsten Horstmann <thorsten@defutech.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[sven@narfation.org: Add commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The code was setting the capabilities byte to zero,
after it was already properly set previously. Fix it.
The bug was found while debugging hwsim mesh tests failures
that happened since the commit mentioned below.
Fixes: 76f43b4c0a93 ("mac80211: Remove invalid flag operations in mesh TSF synchronization")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
These functions drifts TSF timers, not TBTT.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
mesh_sync_offset_adjust_tbtt() implements Extensible synchronization
framework ([1] 13.13.2 Extensible synchronization framework). It shall
not operate the flag "TBTT Adjusting subfield" ([1] 8.4.2.100.8 Mesh
Capability), since it is used only for MBCA ([1] 13.13.4 Mesh beacon
collision avoidance, see 13.13.4.4.3 TBTT scanning and adjustment
procedures for detail). So this patch remove the flag operations.
[1] IEEE Std 802.11 2012
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[remove adjusting_tbtt entirely, since it's now unused]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some drivers (e.g. wl18xx) expect that the last stage in the
de-initialization process will be stopping the beacons, similar to AP flow.
Update ieee80211_stop_mesh() flow accordingly.
As peers can be removed dynamically, this would not impact other drivers.
Tested also on Ralink RT3572 chipset.
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We've accumulated a couple of different fixes now to mesh_sta_cleanup()
due to the different paths that user_mpm and !user_mpm cases take -- one
fix to flush nexthop paths and one to fix the counting.
The only caller of mesh_plink_deactivate() is mesh_sta_cleanup(), so we
can push the user_mpm checks down into there in order to share more
code.
In doing so, we can remove an extra call to mesh_path_flush_by_nexthop()
and the (unnecessary) call to mesh_accept_plinks_update(). This will
also ensure the powersaving state code gets called in the user_mpm case.
The only cleanup tasks we need to avoid when MPM is in user-space
are sending the peering frames and stopping the plink timer, so wrap
those in the appropriate check.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
If a user space program (e.g., wpa_supplicant) deletes a STA entry that
is currently in NL80211_PLINK_ESTAB state, the number of established
plinks counter was not decremented and this could result in rejecting
new plink establishment before really hitting the real maximum plink
limit. For !user_mpm case, this decrementation is handled by
mesh_plink_deactive().
Fix this by decrementing estab_plinks on STA deletion
(mesh_sta_cleanup() gets called from there) so that the counter has a
correct value and the Beacon frame advertisement in Mesh Configuration
element shows the proper value for capability to accept additional
peers.
Cc: stable@vger.kernel.org
Signed-off-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
Currently, the mesh paths associated with a nexthop station are cleaned
up in the following code path:
__sta_info_destroy_part1
synchronize_net()
__sta_info_destroy_part2
-> cleanup_single_sta
-> mesh_sta_cleanup
-> mesh_plink_deactivate
-> mesh_path_flush_by_nexthop
However, there are a couple of problems here:
1) the paths aren't flushed at all if the MPM is running in userspace
(e.g. when using wpa_supplicant or authsae)
2) there is no synchronize_rcu between removing the path and readers
accessing the nexthop, which means the following race is possible:
CPU0 CPU1
~~~~ ~~~~
sta_info_destroy_part1()
synchronize_net()
rcu_read_lock()
mesh_nexthop_resolve()
mpath = mesh_path_lookup()
[...] -> mesh_path_flush_by_nexthop()
sta = rcu_dereference(
mpath->next_hop)
kfree(sta)
access sta <-- CRASH
Fix both of these by unconditionally flushing paths before destroying
the sta, and by adding a synchronize_net() after path flush to ensure
no active readers can still dereference the sta.
Fixes this crash:
[ 348.529295] BUG: unable to handle kernel paging request at 00020040
[ 348.530014] IP: [<f929245d>] ieee80211_mps_set_frame_flags+0x40/0xaa [mac80211]
[ 348.530014] *pde = 00000000
[ 348.530014] Oops: 0000 [#1] PREEMPT
[ 348.530014] Modules linked in: drbg ansi_cprng ctr ccm ppp_generic slhc ipt_MASQUERADE nf_nat_masquerade_ipv4 8021q ]
[ 348.530014] CPU: 0 PID: 20597 Comm: wget Tainted: G O 4.6.0-rc5-wt=V1 #1
[ 348.530014] Hardware name: To Be Filled By O.E.M./To be filled by O.E.M., BIOS 080016 11/07/2014
[ 348.530014] task: f64fa280 ti: f4f9c000 task.ti: f4f9c000
[ 348.530014] EIP: 0060:[<f929245d>] EFLAGS: 00010246 CPU: 0
[ 348.530014] EIP is at ieee80211_mps_set_frame_flags+0x40/0xaa [mac80211]
[ 348.530014] EAX: f4ce63e0 EBX: 00000088 ECX: f3788416 EDX: 00020008
[ 348.530014] ESI: 00000000 EDI: 00000088 EBP: f6409a4c ESP: f6409a40
[ 348.530014] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068
[ 348.530014] CR0: 80050033 CR2: 00020040 CR3: 33190000 CR4: 00000690
[ 348.530014] Stack:
[ 348.530014] 00000000 f4ce63e0 f5f9bd80 f6409a64 f9291d80 0000ce67 f5d51e00 f4ce63e0
[ 348.530014] f3788416 f6409a80 f9291dc1 f4ce8320 f4ce63e0 f5d51e00 f4ce63e0 f4ce8320
[ 348.530014] f6409a98 f9277f6f 00000000 00000000 0000007c 00000000 f6409b2c f9278dd1
[ 348.530014] Call Trace:
[ 348.530014] [<f9291d80>] mesh_nexthop_lookup+0xbb/0xc8 [mac80211]
[ 348.530014] [<f9291dc1>] mesh_nexthop_resolve+0x34/0xd8 [mac80211]
[ 348.530014] [<f9277f6f>] ieee80211_xmit+0x92/0xc1 [mac80211]
[ 348.530014] [<f9278dd1>] __ieee80211_subif_start_xmit+0x807/0x83c [mac80211]
[ 348.530014] [<c04df012>] ? sch_direct_xmit+0xd7/0x1b3
[ 348.530014] [<c022a8c6>] ? __local_bh_enable_ip+0x5d/0x7b
[ 348.530014] [<f956870c>] ? nf_nat_ipv4_out+0x4c/0xd0 [nf_nat_ipv4]
[ 348.530014] [<f957e036>] ? iptable_nat_ipv4_fn+0xf/0xf [iptable_nat]
[ 348.530014] [<c04c6f45>] ? netif_skb_features+0x14d/0x30a
[ 348.530014] [<f9278e10>] ieee80211_subif_start_xmit+0xa/0xe [mac80211]
[ 348.530014] [<c04c769c>] dev_hard_start_xmit+0x1f8/0x267
[ 348.530014] [<c04c7261>] ? validate_xmit_skb.isra.120.part.121+0x10/0x253
[ 348.530014] [<c04defc6>] sch_direct_xmit+0x8b/0x1b3
[ 348.530014] [<c04c7a9c>] __dev_queue_xmit+0x2c8/0x513
[ 348.530014] [<c04c7cfb>] dev_queue_xmit+0xa/0xc
[ 348.530014] [<f91bfc7a>] batadv_send_skb_packet+0xd6/0xec [batman_adv]
[ 348.530014] [<f91bfdc4>] batadv_send_unicast_skb+0x15/0x4a [batman_adv]
[ 348.530014] [<f91b5938>] batadv_dat_send_data+0x27e/0x310 [batman_adv]
[ 348.530014] [<f91c30b5>] ? batadv_tt_global_hash_find.isra.11+0x8/0xa [batman_adv]
[ 348.530014] [<f91b63f3>] batadv_dat_snoop_outgoing_arp_request+0x208/0x23d [batman_adv]
[ 348.530014] [<f91c0cd9>] batadv_interface_tx+0x206/0x385 [batman_adv]
[ 348.530014] [<c04c769c>] dev_hard_start_xmit+0x1f8/0x267
[ 348.530014] [<c04c7261>] ? validate_xmit_skb.isra.120.part.121+0x10/0x253
[ 348.530014] [<c04defc6>] sch_direct_xmit+0x8b/0x1b3
[ 348.530014] [<c04c7a9c>] __dev_queue_xmit+0x2c8/0x513
[ 348.530014] [<f80cbd2a>] ? igb_xmit_frame+0x57/0x72 [igb]
[ 348.530014] [<c04c7cfb>] dev_queue_xmit+0xa/0xc
[ 348.530014] [<f843a326>] br_dev_queue_push_xmit+0xeb/0xfb [bridge]
[ 348.530014] [<f843a35f>] br_forward_finish+0x29/0x74 [bridge]
[ 348.530014] [<f843a23b>] ? deliver_clone+0x3b/0x3b [bridge]
[ 348.530014] [<f843a714>] __br_forward+0x89/0xe7 [bridge]
[ 348.530014] [<f843a336>] ? br_dev_queue_push_xmit+0xfb/0xfb [bridge]
[ 348.530014] [<f843a234>] deliver_clone+0x34/0x3b [bridge]
[ 348.530014] [<f843a68b>] ? br_flood+0x95/0x95 [bridge]
[ 348.530014] [<f843a66d>] br_flood+0x77/0x95 [bridge]
[ 348.530014] [<f843a809>] br_flood_forward+0x13/0x1a [bridge]
[ 348.530014] [<f843a68b>] ? br_flood+0x95/0x95 [bridge]
[ 348.530014] [<f843b877>] br_handle_frame_finish+0x392/0x3db [bridge]
[ 348.530014] [<c04e9b2b>] ? nf_iterate+0x2b/0x6b
[ 348.530014] [<f843baa6>] br_handle_frame+0x1e6/0x240 [bridge]
[ 348.530014] [<f843b4e5>] ? br_handle_local_finish+0x6a/0x6a [bridge]
[ 348.530014] [<c04c4ba0>] __netif_receive_skb_core+0x43a/0x66b
[ 348.530014] [<f843b8c0>] ? br_handle_frame_finish+0x3db/0x3db [bridge]
[ 348.530014] [<c023cea4>] ? resched_curr+0x19/0x37
[ 348.530014] [<c0240707>] ? check_preempt_wakeup+0xbf/0xfe
[ 348.530014] [<c0255dec>] ? ktime_get_with_offset+0x5c/0xfc
[ 348.530014] [<c04c4fc1>] __netif_receive_skb+0x47/0x55
[ 348.530014] [<c04c57ba>] netif_receive_skb_internal+0x40/0x5a
[ 348.530014] [<c04c61ef>] napi_gro_receive+0x3a/0x94
[ 348.530014] [<f80ce8d5>] igb_poll+0x6fd/0x9ad [igb]
[ 348.530014] [<c0242bd8>] ? swake_up_locked+0x14/0x26
[ 348.530014] [<c04c5d29>] net_rx_action+0xde/0x250
[ 348.530014] [<c022a743>] __do_softirq+0x8a/0x163
[ 348.530014] [<c022a6b9>] ? __hrtimer_tasklet_trampoline+0x19/0x19
[ 348.530014] [<c021100f>] do_softirq_own_stack+0x26/0x2c
[ 348.530014] <IRQ>
[ 348.530014] [<c022a957>] irq_exit+0x31/0x6f
[ 348.530014] [<c0210eb2>] do_IRQ+0x8d/0xa0
[ 348.530014] [<c058152c>] common_interrupt+0x2c/0x40
[ 348.530014] Code: e7 8c 00 66 81 ff 88 00 75 12 85 d2 75 0e b2 c3 b8 83 e9 29 f9 e8 a7 5f f9 c6 eb 74 66 81 e3 8c 005
[ 348.530014] EIP: [<f929245d>] ieee80211_mps_set_frame_flags+0x40/0xaa [mac80211] SS:ESP 0068:f6409a40
[ 348.530014] CR2: 0000000000020040
[ 348.530014] ---[ end trace 48556ac26779732e ]---
[ 348.530014] Kernel panic - not syncing: Fatal exception in interrupt
[ 348.530014] Kernel Offset: disabled
Cc: stable@vger.kernel.org
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Tested-by: Fred Veldini <fred.veldini@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh path table needs to be around for the entire time the
interface is in mesh mode, as users can perform an mpath dump
at any time. The existing path table lifetime is instead tied
to the mesh BSS which can cause crashes when different MBSSes
are joined in the context of a single interface, or when the
path table is dumped when no MBSS is joined.
Introduce a new function to perform the final teardown of the
interface and perform path table cleanup there. We already
free the individual path elements when the leaving the mesh
so no additional cleanup is needed there. This fixes the
following crash:
[ 47.753026] BUG: unable to handle kernel paging request at fffffff0
[ 47.753026] IP: [<c0239765>] kthread_data+0xa/0xe
[ 47.753026] *pde = 00741067 *pte = 00000000
[ 47.753026] Oops: 0000 [#4] PREEMPT
[ 47.753026] Modules linked in: ppp_generic slhc 8021q garp mrp sch_fq_codel iptable_mangle ipt_MASQUERADE nf_nat_masquerade_ipv4 iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat ip_tables ath9k_htc ath5k 8139too ath10k_pci ath10k_core arc4 ath9k ath9k_common ath9k_hw mac80211 ath cfg80211 cpufreq_powersave br_netfilter bridge stp llc ipw usb_wwan sierra_net usbnet af_alg natsemi via_rhine mii iTCO_wdt iTCO_vendor_support gpio_ich sierra coretemp pcspkr i2c_i801 lpc_ich ata_generic ata_piix libata ide_pci_generic piix e1000e igb i2c_algo_bit ptp pps_core [last unloaded: 8139too]
[ 47.753026] CPU: 0 PID: 12 Comm: kworker/u2:1 Tainted: G D W 4.5.0-wt-V3 #6
[ 47.753026] Hardware name: To Be Filled By O.E.M./To be filled by O.E.M., BIOS 080016 11/07/2014
[ 47.753026] task: f645a0c0 ti: f6462000 task.ti: f6462000
[ 47.753026] EIP: 0060:[<c0239765>] EFLAGS: 00010002 CPU: 0
[ 47.753026] EIP is at kthread_data+0xa/0xe
[ 47.753026] EAX: 00000000 EBX: 00000000 ECX: 00000000 EDX: 00000000
[ 47.753026] ESI: f645a0c0 EDI: f645a2fc EBP: f6463a80 ESP: f6463a78
[ 47.753026] DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
[ 47.753026] CR0: 8005003b CR2: 00000014 CR3: 353e5000 CR4: 00000690
[ 47.753026] Stack:
[ 47.753026] c0236866 00000000 f6463aac c05768b4 00000009 f6463ba8 f6463ab0 c0247010
[ 47.753026] 00000000 f645a0c0 f6464000 00000009 f6463ba8 f6463ab8 c0576eb2 f645a0c0
[ 47.753026] f6463aec c0228be4 c06335a4 f6463adc f6463ad0 c06c06d4 f6463ae4 c02471b0
[ 47.753026] Call Trace:
[ 47.753026] [<c0236866>] ? wq_worker_sleeping+0xb/0x78
[ 47.753026] [<c05768b4>] __schedule+0xda/0x587
[ 47.753026] [<c0247010>] ? vprintk_default+0x12/0x14
[ 47.753026] [<c0576eb2>] schedule+0x72/0x89
[ 47.753026] [<c0228be4>] do_exit+0xb8/0x71d
[ 47.753026] [<c02471b0>] ? kmsg_dump+0xa9/0xae
[ 47.753026] [<c0203576>] oops_end+0x69/0x70
[ 47.753026] [<c021dcdb>] no_context+0x1bb/0x1c5
[ 47.753026] [<c021de1b>] __bad_area_nosemaphore+0x136/0x140
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c021de32>] bad_area_nosemaphore+0xd/0x10
[ 47.753026] [<c021e0a1>] __do_page_fault+0x26c/0x320
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c021e2fa>] do_page_fault+0xb/0xd
[ 47.753026] [<c05798f8>] error_code+0x58/0x60
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c0239765>] ? kthread_data+0xa/0xe
[ 47.753026] [<c0236866>] ? wq_worker_sleeping+0xb/0x78
[ 47.753026] [<c05768b4>] __schedule+0xda/0x587
[ 47.753026] [<c0247010>] ? vprintk_default+0x12/0x14
[ 47.753026] [<c0576eb2>] schedule+0x72/0x89
[ 47.753026] [<c0228be4>] do_exit+0xb8/0x71d
[ 47.753026] [<c02471b0>] ? kmsg_dump+0xa9/0xae
[ 47.753026] [<c0203576>] oops_end+0x69/0x70
[ 47.753026] [<c021dcdb>] no_context+0x1bb/0x1c5
[ 47.753026] [<c021de1b>] __bad_area_nosemaphore+0x136/0x140
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c021de32>] bad_area_nosemaphore+0xd/0x10
[ 47.753026] [<c021e0a1>] __do_page_fault+0x26c/0x320
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c021e2fa>] do_page_fault+0xb/0xd
[ 47.753026] [<c05798f8>] error_code+0x58/0x60
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c0239765>] ? kthread_data+0xa/0xe
[ 47.753026] [<c0236866>] ? wq_worker_sleeping+0xb/0x78
[ 47.753026] [<c05768b4>] __schedule+0xda/0x587
[ 47.753026] [<c0391e32>] ? put_io_context_active+0x6d/0x95
[ 47.753026] [<c0576eb2>] schedule+0x72/0x89
[ 47.753026] [<c02291f8>] do_exit+0x6cc/0x71d
[ 47.753026] [<c0203576>] oops_end+0x69/0x70
[ 47.753026] [<c021dcdb>] no_context+0x1bb/0x1c5
[ 47.753026] [<c021de1b>] __bad_area_nosemaphore+0x136/0x140
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c021de32>] bad_area_nosemaphore+0xd/0x10
[ 47.753026] [<c021e0a1>] __do_page_fault+0x26c/0x320
[ 47.753026] [<c03b9160>] ? debug_smp_processor_id+0x12/0x16
[ 47.753026] [<c02015e2>] ? __switch_to+0x24/0x40e
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c021e2fa>] do_page_fault+0xb/0xd
[ 47.753026] [<c05798f8>] error_code+0x58/0x60
[ 47.753026] [<c021e2ef>] ? vmalloc_sync_all+0x19a/0x19a
[ 47.753026] [<c03b59d2>] ? rhashtable_walk_init+0x5c/0x93
[ 47.753026] [<f9843221>] mesh_path_tbl_expire.isra.24+0x19/0x82 [mac80211]
[ 47.753026] [<f984408b>] mesh_path_expire+0x11/0x1f [mac80211]
[ 47.753026] [<f9842bb7>] ieee80211_mesh_work+0x73/0x1a9 [mac80211]
[ 47.753026] [<f98207d1>] ieee80211_iface_work+0x2ff/0x311 [mac80211]
[ 47.753026] [<c0235fa3>] process_one_work+0x14b/0x24e
[ 47.753026] [<c0236313>] worker_thread+0x249/0x343
[ 47.753026] [<c02360ca>] ? process_scheduled_works+0x24/0x24
[ 47.753026] [<c0239359>] kthread+0x9e/0xa3
[ 47.753026] [<c0578e50>] ret_from_kernel_thread+0x20/0x40
[ 47.753026] [<c02392bb>] ? kthread_parkme+0x18/0x18
[ 47.753026] Code: 6b c0 85 c0 75 05 e8 fb 74 fc ff 89 f8 84 c0 75 08 8d 45 e8 e8 34 dd 33 00 83 c4 28 5b 5e 5f 5d c3 55 8b 80 10 02 00 00 89 e5 5d <8b> 40 f0 c3 55 b9 04 00 00 00 89 e5 52 8b 90 10 02 00 00 8d 45
[ 47.753026] EIP: [<c0239765>] kthread_data+0xa/0xe SS:ESP 0068:f6463a78
[ 47.753026] CR2: 00000000fffffff0
[ 47.753026] ---[ end trace 867ca0bdd0767790 ]---
Fixes: 3b302ada7f0a ("mac80211: mesh: move path tables into if_mesh")
Reported-by: Fred Veldini <fred.veldini@gmail.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The RMC cache has 256 list heads plus a u32, which puts it at the
unfortunate size of 4104 bytes with padding. kmalloc() will then
round this up to the next power-of-two, so we wind up actually
using two pages here where most of the second is wasted.
Switch to hlist heads here to reduce the structure size down to
fit within a page.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the unlikely case that mesh_rmc_init() fails with -ENOMEM,
the rmc pointer will be left as NULL but the interface is still
operational because ieee80211_mesh_init_sdata() is not allowed
to fail.
If this happens, we would blindly dereference rmc when checking
whether a multicast frame is in the cache. Instead just drop the
frames in the forwarding path.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In the time since the mesh path table was implemented as an
RCU-traversable, dynamically growing hash table, a generic RCU
hashtable implementation was added to the kernel.
Switch the mesh path table over to rhashtable to remove some code
and also gain some features like automatic shrinking.
Cc: Thomas Graf <tgraf@suug.ch>
Cc: netdev@vger.kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The mesh path and mesh gate hashtables are global, containing
all of the mpaths for every mesh interface, but the paths are
all tied logically to a single interface. The common case is
just a single mesh interface, so optimize for that by moving
the global hashtable into the per-interface struct.
Doing so allows us to drop sdata pointer comparisons inside
the lookups and also saves a few bytes of BSS and data.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Here's another round of updates for -next:
* big A-MSDU RX performance improvement (avoid linearize of paged RX)
* rfkill changes: cleanups, documentation, platform properties
* basic PBSS support in cfg80211
* MU-MIMO action frame processing support
* BlockAck reordering & duplicate detection offload support
* various cleanups & little fixes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The station MLME and IBSS/mesh ones use entirely different
code for interpreting HT and VHT operation elements. Change
the code that interprets them a bit - it now modifies an
existing chandef - and use it also in the MLME code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
During a sw scan ieee80211_iface_work ignores work items for all vifs.
However after the scan complete work is requeued only for STA, ADHOC
and MESH iftypes.
This occasionally results in event processing getting delayed/not
processed for iftype AP when it coexists with a STA. This can result
in data halt and eventually disconnection on the AP interface.
Cc: stable@vger.kernel.org
Signed-off-by: Sachin Kulkarni <Sachin.Kulkarni@imgtec.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When 11n peers performs a TDLS connection on a legacy BSS, the HT
operation IE must be specified according to IEEE802.11-2012 section
9.23.3.2. Otherwise HT-protection is compromised and the medium becomes
noisy for both the TDLS and the BSS links.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The function returns always non-negative values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/assign_signed_to_unsigned.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2046107
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implement the basics required for supporting very high throughput
with mesh: include VHT information elements in beacons, probe
responses, and peering action frames, and check for compatible VHT
configurations when peering.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are now a fairly large number of mesh fields that really
aren't needed in any other modes; move those into their own
structure and allocate them separately.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The csa counter has moved from sdata to beacon/presp but
it is not updated accordingly for mesh and ibss. Fix this.
Fixes: af296bdb8da4 ("mac80211: move csa counters from sdata to beacon/presp")
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Lots of updates for net-next; along with the usual flurry
of small fixes, cleanups and internal features we have:
* VHT support for TDLS and IBSS (conditional on drivers though)
* first TX performance improvements (the biggest will come later)
* many suspend/resume (race) fixes
* name_assign_type support from Tom Gundersen
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both wpa_supplicant and mac80211 have and inactivity timer. By default
wpa_supplicant will be timed out in 5 minutes and mac80211's it is 30
minutes. If wpa_supplicant uses a longer timer than mac80211, it will
get unexpected disconnection by mac80211.
Using 0xffffffff instead as the configured value could solve this w/o
changing the code, but due to integer overflow in the expression used
this doesn't work. The expression is:
(current jiffies) > (frame Rx jiffies + NL80211_MESHCONF_PLINK_TIMEOUT * 250)
On 32bit system, the right side would overflow and be a very small
value if NL80211_MESHCONF_PLINK_TIMEOUT is sufficiently large,
causing unexpectedly early disconnections.
Instead allow disabling the inactivity timer to avoid this situation,
by passing the (previously invalid and useless) value 0.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[reword/rewrap commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If we are switching from an HT40+ to an HT40- channel (or vice-versa),
we need the secondary channel offset IE to specify what is the
post-CSA offset to be used. This applies both to beacons and to probe
responses.
In ieee80211_parse_ch_switch_ie() we were ignoring this IE from
beacons and using the *current* HT information IE instead. This was
causing us to use the same offset as before the switch.
Fix that by using the secondary channel offset IE also for beacons and
don't ever use the pre-switch offset. Additionally, remove the
"beacon" argument from ieee80211_parse_ch_switch_ie(), since it's not
needed anymore.
Cc: stable@vger.kernel.org
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
