| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2016-05-04
1) The flowcache can hit an OOM condition if too
many entries are in the gc_list. Fix this by
counting the entries in the gc_list and refuse
new allocations if the value is too high.
2) The inner headers are invalid after a xfrm transformation,
so reset the skb encapsulation field to ensure nobody tries
access the inner headers. Otherwise tunnel devices stacked
on top of xfrm may build the outer headers based on wrong
informations.
3) Add pmtu handling to vti, we need it to report
pmtu informations for local generated packets.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stack object “map” has a total size of 32 bytes. Its last 4
bytes are padding generated by compiler. These padding bytes are
not initialized and sent out via “nla_put”.
Signed-off-by: Kangjie Lu <kjlu@gatech.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case of the mlx4 and mlx5 driver they do not support IPv6 checksum
offload for tunnels. With this being the case we should disable GSO in
addition to the checksum offload features when we find that a device cannot
perform a checksum on a given packet type.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When __vlan_insert_tag() fails from skb_vlan_push() path due to the
skb_cow_head(), we need to undo the __skb_push() in the error path
as well that was done earlier to move skb->data pointer to mac header.
Moreover, I noticed that when in the non-error path the __skb_pull()
is done and the original offset to mac header was non-zero, we fixup
from a wrong skb->data offset in the checksum complete processing.
So the skb_postpush_rcsum() really needs to be done before __skb_pull()
where skb->data still points to the mac header start and thus operates
under the same conditions as in __vlan_insert_tag().
Fixes: 93515d53b133 ("net: move vlan pop/push functions into common code")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes an issue I found in which we were dropping frames if we
had enabled checksums on GRE headers that were encapsulated by either FOU
or GUE. Without this patch I was barely able to get 1 Gb/s of throughput.
With this patch applied I am now at least getting around 6 Gb/s.
The issue is due to the fact that with FOU or GUE applied we do not provide
a transport offset pointing to the GRE header, nor do we offload it in
software as the GRE header is completely skipped by GSO and treated like a
VXLAN or GENEVE type header. As such we need to prevent the stack from
generating it and also prevent GRE from generating it via any interface we
create.
Fixes: c3483384ee511 ("gro: Allow tunnel stacking in the case of FOU/GUE")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is for the recent kcm driver, which introduces AF_KCM(41) in
b7ac4eb(kcm: Kernel Connection Multiplexor module).
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Cc: Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 543e3a8da5a4c453e992d5351ef405d5e32f27d7.
Direct callers of __netpoll_setup() depend on it to set np->dev,
so we can't simply move that assignment up to netpoll_stup().
Reported-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sasha Levin reported a suspicious rcu_dereference_protected() warning
found while fuzzing with trinity that is similar to this one:
[ 52.765684] net/core/filter.c:2262 suspicious rcu_dereference_protected() usage!
[ 52.765688] other info that might help us debug this:
[ 52.765695] rcu_scheduler_active = 1, debug_locks = 1
[ 52.765701] 1 lock held by a.out/1525:
[ 52.765704] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff816a64b7>] rtnl_lock+0x17/0x20
[ 52.765721] stack backtrace:
[ 52.765728] CPU: 1 PID: 1525 Comm: a.out Not tainted 4.5.0+ #264
[...]
[ 52.765768] Call Trace:
[ 52.765775] [<ffffffff813e488d>] dump_stack+0x85/0xc8
[ 52.765784] [<ffffffff810f2fa5>] lockdep_rcu_suspicious+0xd5/0x110
[ 52.765792] [<ffffffff816afdc2>] sk_detach_filter+0x82/0x90
[ 52.765801] [<ffffffffa0883425>] tun_detach_filter+0x35/0x90 [tun]
[ 52.765810] [<ffffffffa0884ed4>] __tun_chr_ioctl+0x354/0x1130 [tun]
[ 52.765818] [<ffffffff8136fed0>] ? selinux_file_ioctl+0x130/0x210
[ 52.765827] [<ffffffffa0885ce3>] tun_chr_ioctl+0x13/0x20 [tun]
[ 52.765834] [<ffffffff81260ea6>] do_vfs_ioctl+0x96/0x690
[ 52.765843] [<ffffffff81364af3>] ? security_file_ioctl+0x43/0x60
[ 52.765850] [<ffffffff81261519>] SyS_ioctl+0x79/0x90
[ 52.765858] [<ffffffff81003ba2>] do_syscall_64+0x62/0x140
[ 52.765866] [<ffffffff817d563f>] entry_SYSCALL64_slow_path+0x25/0x25
Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.
Since the fix in f91ff5b9ff52 ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.
Since its introduction in 994051625981 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.
Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Size of the attribute IFLA_PHYS_PORT_NAME was missing.
Fixes: db24a9044ee1 ("net: add support for phys_port_name")
CC: David Ahern <dsahern@gmail.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the 2 byte padding in struct bpf_tunnel_key between tunnel_ttl
and tunnel_label members explicit. No issue has been observed, and
gcc/llvm does padding for the old struct already, where tunnel_label
was not yet present, so the current code works, but since it's part
of uapi, make sure we don't introduce holes in structs.
Therefore, add tunnel_ext that we can use generically in future
(f.e. to flag OAM messages for backends, etc). Also add the offset
to the compat tests to be sure should some compilers not padd the
tail of the old version of bpf_tunnel_key.
Fixes: 4018ab1875e0 ("bpf: support flow label for bpf_skb_{set, get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netpoll_setup() does a dev_hold() on np->dev, the netpoll device. If it
fails, it correctly does a dev_put() but leaves np->dev set. If we call
netpoll_cleanup() after the failure, np->dev is still set so we do another
dev_put(), which decrements the refcount an extra time.
It's questionable to call netpoll_cleanup() after netpoll_setup() fails,
but it can be difficult to find the problem, and we can easily avoid it in
this case. The extra decrements can lead to hangs like this:
unregister_netdevice: waiting for bond0 to become free. Usage count = -3
Set and clear np->dev at the points where we dev_hold() and dev_put() the
device.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking bugfixes from David Miller:
"Several bug fixes rolling in, some for changes introduced in this
merge window, and some for problems that have existed for some time:
1) Fix prepare_to_wait() handling in AF_VSOCK, from Claudio Imbrenda.
2) The new DST_CACHE should be a silent config option, from Dave
Jones.
3) inet_current_timestamp() unintentionally truncates timestamps to
16-bit, from Deepa Dinamani.
4) Missing reference to netns in ppp, from Guillaume Nault.
5) Free memory reference in hv_netvsc driver, from Haiyang Zhang.
6) Missing kernel doc documentation for function arguments in various
spots around the networking, from Luis de Bethencourt.
7) UDP stopped receiving broadcast packets properly, due to
overzealous multicast checks, fix from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (59 commits)
net: ping: make ping_v6_sendmsg static
hv_netvsc: Fix the order of num_sc_offered decrement
net: Fix typos and whitespace.
hv_netvsc: Fix the array sizes to be max supported channels
hv_netvsc: Fix accessing freed memory in netvsc_change_mtu()
ppp: take reference on channels netns
net: Reset encap_level to avoid resetting features on inner IP headers
net: mediatek: fix checking for NULL instead of IS_ERR() in .probe
net: phy: at803x: Request 'reset' GPIO only for AT8030 PHY
at803x: fix reset handling
AF_VSOCK: Shrink the area influenced by prepare_to_wait
Revert "vsock: Fix blocking ops call in prepare_to_wait"
macb: fix PHY reset
ipv4: initialize flowi4_flags before calling fib_lookup()
fsl/fman: Workaround for Errata A-007273
ipv4: fix broadcast packets reception
net: hns: bug fix about the overflow of mss
net: hns: adds limitation for debug port mtu
net: hns: fix the bug about mtu setting
net: hns: fixes a bug of RSS
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull more rdma updates from Doug Ledford:
"Round two of 4.6 merge window patches.
This is a monster pull request. I held off on the hfi1 driver updates
(the hfi1 driver is intimately tied to the qib driver and the new
rdmavt software library that was created to help both of them) in my
first pull request. The hfi1/qib/rdmavt update is probably 90% of
this pull request. The hfi1 driver is being left in staging so that
it can be fixed up in regards to the API that Al and yourself didn't
like. Intel has agreed to do the work, but in the meantime, this
clears out 300+ patches in the backlog queue and brings my tree and
their tree closer to sync.
This also includes about 10 patches to the core and a few to mlx5 to
create an infrastructure for configuring SRIOV ports on IB devices.
That series includes one patch to the net core that we sent to netdev@
and Dave Miller with each of the three revisions to the series. We
didn't get any response to the patch, so we took that as implicit
approval.
Finally, this series includes Intel's new iWARP driver for their x722
cards. It's not nearly the beast as the hfi1 driver. It also has a
linux-next merge issue, but that has been resolved and it now passes
just fine.
Summary:
- A few minor core fixups needed for the next patch series
- The IB SRIOV series. This has bounced around for several versions.
Of note is the fact that the first patch in this series effects the
net core. It was directed to netdev and DaveM for each iteration
of the series (three versions total). Dave did not object, but did
not respond either. I've taken this as permission to move forward
with the series.
- The new Intel X722 iWARP driver
- A huge set of updates to the Intel hfi1 driver. Of particular
interest here is that we have left the driver in staging since it
still has an API that people object to. Intel is working on a fix,
but getting these patches in now helps keep me sane as the upstream
and Intel's trees were over 300 patches apart"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (362 commits)
IB/ipoib: Allow mcast packets from other VFs
IB/mlx5: Implement callbacks for manipulating VFs
net/mlx5_core: Implement modify HCA vport command
net/mlx5_core: Add VF param when querying vport counter
IB/ipoib: Add ndo operations for configuring VFs
IB/core: Add interfaces to control VF attributes
IB/core: Support accessing SA in virtualized environment
IB/core: Add subnet prefix to port info
IB/mlx5: Fix decision on using MAD_IFC
net/core: Add support for configuring VF GUIDs
IB/{core, ulp} Support above 32 possible device capability flags
IB/core: Replace setting the zero values in ib_uverbs_ex_query_device
net/mlx5_core: Introduce offload arithmetic hardware capabilities
net/mlx5_core: Refactor device capability function
net/mlx5_core: Fix caching ATOMIC endian mode capability
ib_srpt: fix a WARN_ON() message
i40iw: Replace the obsolete crypto hash interface with shash
IB/hfi1: Add SDMA cache eviction algorithm
IB/hfi1: Switch to using the pin query function
IB/hfi1: Specify mm when releasing pages
...
|
|
Add two new NLAs to support configuration of Infiniband node or port
GUIDs. New applications can choose to use this interface to configure
GUIDs with iproute2 with commands such as:
ip link set dev ib0 vf 0 node_guid 00:02:c9:03:00:21:6e:70
ip link set dev ib0 vf 0 port_guid 00:02:c9:03:00:21:6e:78
A new ndo, ndo_sef_vf_guid is introduced to notify the net device of the
request to change the GUID.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
It can be useful to report dev->gso_max_segs and dev->gso_max_size
so that "ip -d link" can display them to help debugging.
For the moment, these attributes are read-only.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Petri Gynther <pgynther@google.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the function dev_get_phys_port_name was added it missed a description
for it's len argument. Adding it.
Fixes: db24a9044ee1 ("net: add support for phys_port_name")
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 22e0f8b9322c ("net: sched: make bstats per cpu and estimator RCU safe")
added the argument cpu_bstats to functions gen_new_estimator and
gen_replace_estimator and now the descriptions of these are missing for the
documentation. Adding them.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function gnet_stats_copy_basic is missing the description of the cpu
argument in the documentation. Adding it.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When drivers express support for TSO of encapsulated packets, they
only mean that they can do it for one layer of encapsulation.
Supporting additional levels would mean updating, at a minimum,
more IP length fields and they are unaware of this.
No encapsulation device expresses support for handling offloaded
encapsulated packets, so we won't generate these types of frames
in the transmit path. However, GRO doesn't have a check for
multiple levels of encapsulation and will attempt to build them.
UDP tunnel GRO actually does prevent this situation but it only
handles multiple UDP tunnels stacked on top of each other. This
generalizes that solution to prevent any kind of tunnel stacking
that would cause problems.
Fixes: bf5a755f ("net-gre-gro: Add GRE support to the GRO stack")
Signed-off-by: Jesse Gross <jesse@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TCP protocol is still used these days, and TCP uses
clones in its transmit path. We can not optimize linux
stack assuming it is mostly used in routers, or that TCP
is dead.
Fixes: 795bb1c00d ("net: bulk free infrastructure for NAPI context, use napi_consume_skb")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
|
|
eBPF defines this as BPF_TUNLEN_MAX and OVS just uses the hard-coded
value inside struct sw_flow_key. Thus, add and use IP_TUNNEL_OPTS_MAX
for this, which makes the code a bit more generic and allows to remove
BPF_TUNLEN_MAX from eBPF code.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can just add a small helper dst_tclassid() for retrieving the
dst->tclassid value. It makes the code a bit better in that we can
get rid of the ifdef from filter.c by moving this into the header.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the tc_classid from eBPF skb context is write-only, but there's
no good reason for tc programs to limit it to write-only. For example,
it can be used to transfer its state via tail calls where the resulting
tc_classid gets filled gradually.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The success of CMA allocation largely depends on the success of
migration and key factor of it is page reference count. Until now, page
reference is manipulated by direct calling atomic functions so we cannot
follow up who and where manipulate it. Then, it is hard to find actual
reason of CMA allocation failure. CMA allocation should be guaranteed
to succeed so finding offending place is really important.
In this patch, call sites where page reference is manipulated are
converted to introduced wrapper function. This is preparation step to
add tracepoint to each page reference manipulation function. With this
facility, we can easily find reason of CMA allocation failure. There is
no functional change in this patch.
In addition, this patch also converts reference read sites. It will
help a second step that renames page._count to something else and
prevents later attempt to direct access to it (Suggested by Andrew).
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We can hit an OOM condition if we are under presure because
we can not free the entries in gc_list fast enough. So add
a counter for the not yet freed entries in the gc_list and
refuse new allocations if the value is too high.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
When the ETHTOOL_GLINKSETTINGS implementation finds that userland is
using the wrong number of words of link mode bitmaps (or is trying to
find out the right numbers) it sets the cmd field to 0 in the response
structure.
This is inconsistent with the implementation of every other ethtool
command, so let's remove that inconsistency before it gets into a
stable release.
Fixes: 3f1ac7a700d03 ("net: ethtool: add new ETHTOOL_xLINKSETTINGS API")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This basic implementation allows to share code between driver using
hardware buffer management. As the code is hardware agnostic, there is
few helpers, most of the optimization brought by the an HW BM has to be
done at driver level.
Tested-by: Sebastian Careba <nitroshift@yahoo.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers reuse/share code paths that free SKBs between NAPI
and non-NAPI calls. Adjust napi_consume_skb to handle this
use-case.
Before, calls from netpoll (w/ IRQs disabled) was handled and
indicated with a budget zero indication. Use the same zero
indication to handle calls not originating from NAPI/softirq.
Simply handled by using dev_consume_skb_any().
This adds an extra branch+call for the netpoll case (checking
in_irq() + irqs_disabled()), but that is okay as this is a slowpath.
Suggested-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends bpf_tunnel_key with a tunnel_label member, that maps
to ip_tunnel_key's label so underlying backends like vxlan and geneve
can propagate the label to udp_tunnel6_xmit_skb(), where it's being set
in the IPv6 header. It allows for having 20 more bits to encode/decode
flow related meta information programmatically. Tested with vxlan and
geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_flow_dissector_target() public
Will be used in a following patch to query if a key is being used, and
what it's value in the target object.
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Amir Vadai <amir@vadai.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add walking of fragments in __skb_splice_bits.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The assumptions from commit 0c1d70af924b ("net: use dst_cache for vxlan
device"), 468dfffcd762 ("geneve: add dst caching support") and 3c1cb4d2604c
("net/ipv4: add dst cache support for gre lwtunnels") on dst_cache usage
when ip_tunnel_info is used is unfortunately not always valid as assumed.
While it seems correct for ip_tunnel_info front-ends such as OVS, eBPF
however can fill in ip_tunnel_info for consumers like vxlan, geneve or gre
with different remote dsts, tos, etc, therefore they cannot be assumed as
packet independent.
Right now vxlan, geneve, gre would cache the dst for eBPF and every packet
would reuse the same entry that was first created on the initial route
lookup. eBPF doesn't store/cache the ip_tunnel_info, so each skb may have
a different one.
Fix it by adding a flag that checks the ip_tunnel_info. Also the !tos test
in vxlan needs to be handeled differently in this context as it is currently
inferred from ip_tunnel_info as well if present. ip_tunnel_dst_cache_usable()
helper is added for the three tunnel cases, which checks if we can use dst
cache.
Fixes: 0c1d70af924b ("net: use dst_cache for vxlan device")
Fixes: 468dfffcd762 ("geneve: add dst caching support")
Fixes: 3c1cb4d2604c ("net/ipv4: add dst cache support for gre lwtunnels")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After eBPF being able to programmatically access/manage tunnel key meta
data via commit d3aa45ce6b94 ("bpf: add helpers to access tunnel metadata")
and more recently also for IPv6 through c6c33454072f ("bpf: support ipv6
for bpf_skb_{set,get}_tunnel_key"), this work adds two complementary
helpers to generically access their auxiliary tunnel options.
Geneve and vxlan support this facility. For geneve, TLVs can be pushed,
and for the vxlan case its GBP extension. I.e. setting tunnel key for geneve
case only makes sense, if we can also read/write TLVs into it. In the GBP
case, it provides the flexibility to easily map the group policy ID in
combination with other helpers or maps.
I chose to model this as two separate helpers, bpf_skb_{set,get}_tunnel_opt(),
for a couple of reasons. bpf_skb_{set,get}_tunnel_key() is already rather
complex by itself, and there may be cases for tunnel key backends where
tunnel options are not always needed. If we would have integrated this
into bpf_skb_{set,get}_tunnel_key() nevertheless, we are very limited with
remaining helper arguments, so keeping compatibility on structs in case of
passing in a flat buffer gets more cumbersome. Separating both also allows
for more flexibility and future extensibility, f.e. options could be fed
directly from a map, etc.
Moreover, change geneve's xmit path to test only for info->options_len
instead of TUNNEL_GENEVE_OPT flag. This makes it more consistent with vxlan's
xmit path and allows for avoiding to specify a protocol flag in the API on
xmit, so it can be protocol agnostic. Having info->options_len is enough
information that is needed. Tested with vxlan and geneve.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added by 9a628224a61b ("ip_tunnel: Add dont fragment flag."), allow to
feed df flag into tunneling facilities (currently supported on TX by
vxlan, geneve and gre) as a hint from eBPF's bpf_skb_set_tunnel_key()
helper.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
They are only used here, so there's no reason they should not be static.
Only the vlan push/pop protos are used in the test_bpf suite.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When overwriting parts of the packet with bpf_skb_store_bytes() that
were fed previously into skb->hash calculation, we should clear the
current hash with skb_clear_hash(), so that a next skb_get_hash() call
can determine the correct hash related to this skb.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 7d672345ed29 ("bpf: add generic bpf_csum_diff helper") added a
generic checksum diff helper that can feed bpf_l4_csum_replace() with
a target __wsum diff that is to be applied to the L4 checksum. This
facility is very flexible, can be cascaded, allows for adding, removing,
or diffing data, or for calculating the pseudo header checksum from
scratch, but it can also be reused for working with the IPv4 header
checksum.
Thus, analogous to bpf_l4_csum_replace(), add a case for header field
value of 0 to change the checksum at a given offset through a new helper
csum_replace_by_diff(). Also, in addition to that, this provides an
easy to use interface for feeding precalculated diffs f.e. coming from
a map. It nicely complements bpf_l3_csum_replace() that currently allows
only for csum updates of 2 and 4 byte diffs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
3b766cd832328fcb87db3507e7b98cf42f21689d ("net/core: Add reading VF
statistics through the PF netdevice") added that variable but it's never
been used.
Signed-off-by: Eric Engestrom <eric.engestrom@imgtec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since offset is zero, it's not necessary to use set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 52bd2d62ce67 ("net: better skb->sender_cpu and skb->napi_id cohabitation")
skb_sender_cpu_clear() becomes empty and can be removed.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce devlink infrastructure for drivers to register and expose to
userspace via generic Netlink interface.
There are two basic objects defined:
devlink - one instance for every "parent device", for example switch ASIC
devlink port - one instance for every physical port of the device.
This initial portion implements basic get/dump of objects to userspace.
Also, port splitter and port type setting is implemented.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the send skbuff reaches the end, nlmsg_put and friends returns
-EMSGSIZE but it is silently thrown away in ndo_fdb_dump. It is called
within a for_each_netdev loop and the first fdb entry of a following
netdev could fit in the remaining skbuff. This breaks the mechanism
of cb->args[0] and idx to keep track of the entries that are already
dumped, which results missing entries in bridge fdb show command.
Signed-off-by: Minoura Makoto <minoura@valinux.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
replaced by __ethtool_get_link_ksettings.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch defines a new ETHTOOL_GLINKSETTINGS/SLINKSETTINGS API,
handled by the new get_link_ksettings/set_link_ksettings callbacks.
This API provides support for most legacy ethtool_cmd fields, adds
support for larger link mode masks (up to 4064 bits, variable length),
and removes ethtool_cmd deprecated
fields (transceiver/maxrxpkt/maxtxpkt).
This API is deprecating the legacy ETHTOOL_GSET/SSET API and provides
the following backward compatibility properties:
- legacy ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks.
- legacy ethtool with new get/set_link_ksettings drivers: the new
driver callbacks are used, data internally converted to legacy
ethtool_cmd. ETHTOOL_GSET will return only the 1st 32b of each link
mode mask. ETHTOOL_SSET will fail if user tries to set the
ethtool_cmd deprecated fields to
non-0 (transceiver/maxrxpkt/maxtxpkt). A kernel warning is logged if
driver sets higher bits.
- future ethtool with legacy drivers: no change, still using the
get_settings/set_settings callbacks, internally converted to new data
structure. Deprecated fields (transceiver/maxrxpkt/maxtxpkt) will be
ignored and seen as 0 from user space. Note that that "future"
ethtool tool will not allow changes to these deprecated fields.
- future ethtool with new drivers: direct call to the new callbacks.
By "future" ethtool, what is meant is:
- query: first try ETHTOOL_GLINKSETTINGS, and revert to ETHTOOL_GSET if
fails
- set: query first and remember which of ETHTOOL_GLINKSETTINGS or
ETHTOOL_GSET was successful
+ if ETHTOOL_GLINKSETTINGS was successful, then change config with
ETHTOOL_SLINKSETTINGS. A failure there is final (do not try
ETHTOOL_SSET).
+ otherwise ETHTOOL_GSET was successful, change config with
ETHTOOL_SSET. A failure there is final (do not try
ETHTOOL_SLINKSETTINGS).
The interaction user/kernel via the new API requires a small
ETHTOOL_GLINKSETTINGS handshake first to agree on the length of the link
mode bitmaps. If kernel doesn't agree with user, it returns the bitmap
length it is expecting from user as a negative length (and cmd field is
0). When kernel and user agree, kernel returns valid info in all
fields (ie. link mode length > 0 and cmd is ETHTOOL_GLINKSETTINGS).
Data structure crossing user/kernel boundary is 32/64-bit
agnostic. Converted internally to a legal kernel bitmap.
The internal __ethtool_get_settings kernel helper will gradually be
replaced by __ethtool_get_link_ksettings by the time the first
"link_settings" drivers start to appear. So this patch doesn't change
it, it will be removed before it needs to be changed.
Signed-off-by: David Decotigny <decot@googlers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add the SO_CNX_ADVICE socket option (setsockopt only). The
purpose is to allow an application to give feedback to the kernel about
the quality of the network path for a connected socket. The value
argument indicates the type of quality report. For this initial patch
the only supported advice is a value of 1 which indicates "bad path,
please reroute"-- the action taken by the kernel is to call
dst_negative_advice which will attempt to choose a different ECMP route,
reset the TX hash for flow label and UDP source port in encapsulation,
etc.
This facility should be useful for connected UDP sockets where only the
application can provide any feedback about path quality. It could also
be useful for TCP applications that have additional knowledge about the
path outside of the normal TCP control loop.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to update the skb->csum after pulling the skb, otherwise
an unnecessary checksum (re)computation can ocure for IGMP/MLD packets
in the bridge code. Additionally this fixes the following splats for
network devices / bridge ports with support for and enabled RX checksum
offloading:
[...]
[ 43.986968] eth0: hw csum failure
[ 43.990344] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.4.0 #2
[ 43.996193] Hardware name: BCM2709
[ 43.999647] [<800204e0>] (unwind_backtrace) from [<8001cf14>] (show_stack+0x10/0x14)
[ 44.007432] [<8001cf14>] (show_stack) from [<801ab614>] (dump_stack+0x80/0x90)
[ 44.014695] [<801ab614>] (dump_stack) from [<802e4548>] (__skb_checksum_complete+0x6c/0xac)
[ 44.023090] [<802e4548>] (__skb_checksum_complete) from [<803a055c>] (ipv6_mc_validate_checksum+0x104/0x178)
[ 44.032959] [<803a055c>] (ipv6_mc_validate_checksum) from [<802e111c>] (skb_checksum_trimmed+0x130/0x188)
[ 44.042565] [<802e111c>] (skb_checksum_trimmed) from [<803a06e8>] (ipv6_mc_check_mld+0x118/0x338)
[ 44.051501] [<803a06e8>] (ipv6_mc_check_mld) from [<803b2c98>] (br_multicast_rcv+0x5dc/0xd00)
[ 44.060077] [<803b2c98>] (br_multicast_rcv) from [<803aa510>] (br_handle_frame_finish+0xac/0x51c)
[...]
Fixes: 9afd85c9e455 ("net: Export IGMP/MLD message validation code")
Reported-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
