| Age | Commit message (Collapse) | Author |
|---|
|
This makes hci_suspend_notifier use the hci_*_sync which can be
executed synchronously which is allowed in the suspend_notifier and
simplifies a lot of the handling since the status of each command can
be checked inline so no other work need to be scheduled thus can be
performed without using of a state machine.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
During system suspend, advertisement monitoring is disabled by setting
the HCI_VS_MSFT_LE_Set_Advertisement_Filter_Enable to False. This
disables the monitoring during suspend, however, if the controller is
monitoring a device, it sends HCI_VS_MSFT_LE_Monitor_Device_Event to
indicate that the monitoring has been stopped for that particular
device. This event may occur after suspend depending on the
low_threshold_timeout and peer device advertisement frequency, which
causes early wake up.
Right way to disable the monitoring for suspend is by removing all the
monitors before suspend and re-monitor after resume to ensure no events
are received during suspend. This patch fixes this suspend/resume issue.
Following tests are performed:
- Add monitors before suspend and make sure DeviceFound gets triggered
- Suspend the system and verify that all monitors are removed by kernel
but not Released by bluetoothd
- Wake up and verify that all monitors are added again and DeviceFound
gets triggered
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Reviewed-by: Archie Pusaka <apusaka@google.com>
Reviewed-by: Miao-chen Chou <mcchou@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This splits the msft_do_{open/close} to msft_do_{open/close} and
msft_{register/unregister}. With this change it is possible to retain
the MSFT extension info irrespective of controller power on/off state.
This helps bluetoothd to report correct 'supported features' of the
controller to the D-Bus clients event if the controller is off. It also
re-reads the MSFT info upon every msft_do_open().
The following test steps were performed.
1. Boot the test device and verify the MSFT support debug log in syslog.
2. Power off the controller and read the 'supported features', power on
and read again.
3. Restart the bluetoothd and verify the 'supported features' value.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Reviewed-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Alain Michaud <alainm@chromium.org>
Signed-off-by: Manish Mandlik <mmandlik@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Some controllers don't support the Simple Pairing Options feature that
can indicate the support for P-192 and P-256 public key validation.
However they might support the Microsoft vendor extension that can
indicate the validiation capability as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
|
|
This adds logic to disable and reenable advertisement filters during
suspend and resume. After this patch, we would only receive packets from
devices in allow list during suspend.
Signed-off-by: Howard Chung <howardchung@google.com>
Reviewed-by: Abhishek Pandit-Subedi <abhishekpandit@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Implements the feature to disable/enable the filter used for
advertising monitor on MSFT controller, effectively have the same
effect as "remove all monitors" and "add all previously removed
monitors".
This feature would be needed when suspending, where we would not want
to get packets from anything outside the allowlist. Note that the
integration with the suspending part is not included in this patch.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Implements the monitor removal functionality for advertising monitor
offloading to MSFT controllers. Supply handle = 0 to remove all
monitors.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Enables advertising monitor offloading to the controller, if MSFT
extension is supported. The kernel won't adjust the monitor parameters
to match what the controller supports - that is the user space's
responsibility.
This patch only manages the addition of monitors. Monitor removal is
going to be handled by another patch.
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Manish Mandlik <mmandlik@chromium.org>
Reviewed-by: Miao-chen Chou <mcchou@chromium.org>
Reviewed-by: Yun-Hao Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This adds the request handler of MGMT_OP_READ_ADV_MONITOR_FEATURES
command. Since the controller-based monitoring is not yet in place, this
report only the supported features but not the enabled features.
The following test was performed.
- Issuing btmgmt advmon-features.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
Micrsoft defined a set for HCI vendor extensions. Check the following
link for details:
https://docs.microsoft.com/en-us/windows-hardware/drivers/bluetooth/microsoft-defined-bluetooth-hci-commands-and-events
This provides the basic framework to enable the extension and read its
supported features. Drivers still have to declare support for this
extension before it can be utilized by the host stack.
Signed-off-by: Miao-chen Chou <mcchou@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
