| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
All conflicts were simple overlapping changes except perhaps
for the Thunder driver.
That driver has a change_mtu method explicitly for sending
a message to the hardware. If that fails it returns an
error.
Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.
However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature patchset includes the following changes:
- 6 patches adding functionality to detect a WiFi interface under
other virtual interfaces, like VLANs. They introduce a cache for
the detected the WiFi configuration to avoid RTNL locking in
critical sections. Patches have been prepared by Marek Lindner
and Sven Eckelmann
- Enable automatic module loading for genl requests, by Sven Eckelmann
- Fix a potential race condition on interface removal. This is not
happening very often in practice, but requires bigger changes to fix,
so we are sending this to net-next. By Linus Luessing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
pull request for net-next: batman-adv 2016-11-08 v2
This feature and cleanup patchset includes the following changes:
- netlink and code cleanups by Sven Eckelmann (3 patches)
- Cleanup and minor fixes by Linus Luessing (3 patches)
- Speed up multicast update intervals, by Linus Luessing
- Avoid (re)broadcast in meshes for some easy cases,
by Linus Luessing
- Clean up tx return state handling, by Sven Eckelmann (6 patches)
- Fix some special mac address handling cases, by Sven Eckelmann
(3 patches)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Things like VLANs don't have their link set when they are created. Thus
the wifi flags have to be evaluated later to fix their contents for the
link interface.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[sven.eckelmann@open-mesh.com: re-add batadv_get_real_netdev to take rtnl
semaphore for batadv_get_real_netdevice]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
In a few situations batman-adv tries to determine whether a given interface
is a WiFi interface to enable specific WiFi optimizations. If the interface
batman-adv has been configured with is a virtual interface (e.g. VLAN) it
would not be properly detected as WiFi interface and thus not benefit from
the special WiFi treatment.
This patch changes that by peeking under the hood whenever a virtual
interface is in play.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[sven.eckelmann@open-mesh.com: integrate in wifi_flags caching, retrieve
namespace of link interface]
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
batman-adv is requiring the type of wifi device in different contexts. Some
of them can take the rtnl semaphore and some of them already have the
semaphore taken. But even others don't allow that the semaphore will be
taken.
The data has to be retrieved when the hardif is added to batman-adv because
some of the wifi information for an hardif will only be available with rtnl
lock. It can then be cached in the batadv_hard_iface and the functions
is_wifi_netdev and is_cfg80211_netdev can just compare the correct bits
without imposing extra locking requirements.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The ELP protocol requires cfg80211 to auto-detect the WiFi througput
to a given neighbor. Use batadv_is_cfg80211_netdev() to determine
whether or not an interface is eligible.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The returned net_namespace of batadv_getlink_net may be used with functions
that potentially modify the struct. Thus it must return the pointer as
non-const like rtnl_link_ops::get_link_net does.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The commit 9799c50372b2 ("batman-adv: fix splat on disabling an interface")
fixed a warning but at the same time broke the rtnl function add_slave for
devices which were temporarily removed.
batadv_softif_slave_add requires soft_iface of and hard_iface to be NULL
before it is allowed to be enslaved. But this resetting of soft_iface to
NULL in batadv_hardif_disable_interface was removed with the aforementioned
commit.
Reported-by: Julian Labus <julian@freifunk-rtk.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
With this patch, (re)broadcasting on a specific interfaces is avoided:
* No neighbor: There is no need to broadcast on an interface if there
is no node behind it.
* Single neighbor is source: If there is just one neighbor on an
interface and if this neighbor is the one we actually got this
broadcast packet from, then we do not need to echo it back.
* Single neighbor is originator: If there is just one neighbor on
an interface and if this neighbor is the originator of this
broadcast packet, then we do not need to echo it back.
Goodies for BATMAN V:
("Upgrade your BATMAN IV network to V now to get these for free!")
Thanks to the split of OGMv1 into two packet types, OGMv2 and ELP
that is, we can now apply the same optimizations stated above to OGMv2
packets, too.
Furthermore, with BATMAN V, rebroadcasts can be reduced in certain
multi interface cases, too, where BATMAN IV cannot. This is thanks to
the removal of the "secondary interface originator" concept in BATMAN V.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
As long as there is still a reference for a hard interface held, there might
still be a forwarding packet relying on its attributes.
Therefore avoid setting hard_iface->soft_iface to NULL when disabling a hard
interface.
This fixes the following, potential splat:
batman_adv: bat0: Interface deactivated: eth1
batman_adv: bat0: Removing interface: eth1
cgroup: new mount options do not match the existing superblock, will be ignored
batman_adv: bat0: Interface deactivated: eth3
batman_adv: bat0: Removing interface: eth3
------------[ cut here ]------------
WARNING: CPU: 3 PID: 1986 at ./net/batman-adv/bat_iv_ogm.c:549 batadv_iv_send_outstanding_bat_ogm_packet+0x145/0x643 [batman_adv]
Modules linked in: batman_adv(O-) <...>
CPU: 3 PID: 1986 Comm: kworker/u8:2 Tainted: G W O 4.6.0-rc6+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014
Workqueue: bat_events batadv_iv_send_outstanding_bat_ogm_packet [batman_adv]
0000000000000000 ffff88001d93bca0 ffffffff8126c26b 0000000000000000
0000000000000000 ffff88001d93bcf0 ffffffff81051615 ffff88001f19f818
000002251d93bd68 0000000000000046 ffff88001dc04a00 ffff88001becbe48
Call Trace:
[<ffffffff8126c26b>] dump_stack+0x67/0x90
[<ffffffff81051615>] __warn+0xc7/0xe5
[<ffffffff8105164b>] warn_slowpath_null+0x18/0x1a
[<ffffffffa0356f24>] batadv_iv_send_outstanding_bat_ogm_packet+0x145/0x643 [batman_adv]
[<ffffffff8108b01f>] ? __lock_is_held+0x32/0x54
[<ffffffff810689a2>] process_one_work+0x2a8/0x4f5
[<ffffffff81068856>] ? process_one_work+0x15c/0x4f5
[<ffffffff81068df2>] worker_thread+0x1d5/0x2c0
[<ffffffff81068c1d>] ? process_scheduled_works+0x2e/0x2e
[<ffffffff81068c1d>] ? process_scheduled_works+0x2e/0x2e
[<ffffffff8106dd90>] kthread+0xc0/0xc8
[<ffffffff8144de82>] ret_from_fork+0x22/0x40
[<ffffffff8106dcd0>] ? __init_kthread_worker+0x55/0x55
---[ end trace 647f9f325123dc05 ]---
What happened here is, that there was still a forw_packet (here: a BATMAN IV
OGM) in the queue of eth3 with the forw_packet->if_incoming set to eth1 and the
forw_packet->if_outgoing set to eth3.
When eth3 is to be deactivated and removed, then this thread waits for the
forw_packet queued on eth3 to finish. Because eth1 was deactivated and removed
earlier and by that had forw_packet->if_incoming->soft_iface, set to NULL, the
splat when trying to send/flush the OGM on eth3 occures.
Fixes: c6c8fea29769 ("net: Add batman-adv meshing protocol")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
[sven@narfation.org: Reduced size of Oops message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
Switch-like virtual interfaces like bridge or openvswitch don't destroy
itself when all their attached netdevices dissappear. Instead they only
remove the link to the unregistered device and keep working until they get
removed manually.
This has the benefit that all configurations for this interfaces are kept
and daemons reacting to rtnl events can just add new slave interfaces
without going through the complete configuration of the switch-like
netdevice.
Handling unregister events of client devices similar in batman-adv allows
users to drop their current workaround of dummy netdevices attached to
batman-adv soft-interfaces.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
It is hard to understand why the refcnt is increased when it isn't done
near the actual place the new reference is used. So using kref_get right
before the place which requires the reference and in the same function
helps to avoid accidental problems caused by incorrect reference counting.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
batman-adv tries to prevent the user from placing a batX soft
interface into another batman mesh as a hard interface. It does this
by walking up the devices list of parents and ensures they are all
none batX interfaces. iflink can point to an interface in a different
namespace, so also retrieve the parents name space when finding the
parent and use it when doing the comparison.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: Fix alignments, simplify parent netns retrieval]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Postponing the removal of the interface breaks the expected behavior of
NETDEV_UNREGISTER and NETDEV_PRE_TYPE_CHANGE. This is especially
problematic when an interface is removed and added in quick succession.
This reverts commit 5bc44dc8458c ("batman-adv: postpone sysfs removal when
unregistering").
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The routing API data structure contains several function
pointers that can easily be grouped together based on the
component they work with.
Split the API in subobjects in order to improve definition readability.
At the same time, remove the "bat_" prefix from the API object and
its fields names. These are batman-adv private structs and there is no
need to always prepend such prefix, which only makes function invocations
much much longer.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Reviewed-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The bat_algo.h had some functions declared which were not part of the
bat_algo.c file. These are instead stored in bat_v.c and bat_iv_ogm.c. The
declaration should therefore be also in bat_v.h and bat_iv_ogm,h to make
them easier to find.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
There are several places in batman-adv which provide logging related
functions. These should be grouped together in the log.* files to make them
easier to find.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
It is easier to detect if a include is already there for a used
functionality when the includes are ordered. Using an alphabetic order
together with the grouping in commit 1e2c2a4fe4a5 ("batman-adv: Add
required includes to all files") makes includes better manageable.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The ELP interval and throughput override interface settings are initialized
with default settings on every time an interface is added to a mesh.
This patch prevents this behavior by moving the configuration init to the
interface detection routine which runs only once per interface.
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
[a@unstable.cc: move initialization to batadv_v_hardif_init]
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
The ogm_emit and ogm_schedule API calls were rather tight to the
B.A.T.M.A.N. IV logic and therefore rather difficult to use
with other algorithm implementations.
Remove such calls and move the surrounding logic into the
B.A.T.M.A.N. IV specific code.
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
|
|
It is easier to understand that the returned value of a specific function
doesn't have to be 0 when the functions was successful when the actual
return type is bool. This is especially true when all surrounding functions
with return type int use negative values to return the error code.
Reported-by: Nicholas Krause <xerofoify@gmail.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The callers of the functions using batadv_hard_iface objects already make
sure that they hold a valid reference. The subfunctions don't have
to check whether the reference counter is > 0 because this was checked by
the callers.
The kref_get function instead WARNs (with debug information) when the
reference counter would still be 0. This makes a bug in batman-adv better
visible because kref_get_unless_zero would have ignored this problem.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The hard_iface is referenced in the packet_type for batman-adv. Increase
the refcounter of the hard_interface for it to have an explicit reference
for it in case this functionality gets refactorted and the currently
used implicit reference for it will be removed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
When creating a soft interface, create it in the same netns as the
hard interface. Replace all references to init_net with the correct
name space for the interface being manipulated.
Suggested-by: Daniel Ehlers <danielehlers@mindeye.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
At the moment there is no explicit reactivation of an hard-interface
upon NETDEV_UP event. In case of B.A.T.M.A.N. IV the interface is
reactivated as soon as the next OGM is scheduled for sending, but this
mechanism does not work with B.A.T.M.A.N. V. The latter does not rely
on the same scheduling mechanism as its predecessor and for this reason
the hard-interface remains deactivated forever after being brought down
once.
This patch fixes the reactivation mechanism by adding a new routing API
which explicitly allows each algorithm to perform any needed operation
upon interface re-activation.
Such API is optional and is implemented by B.A.T.M.A.N. V only and it
just takes care of setting the iface status to ACTIVE
Signed-off-by: Antonio Quartulli <a@unstable.cc>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The shutdown of an batman-adv interface can happen with one of its slave
interfaces still being in the BATADV_IF_TO_BE_ACTIVATED state. A possible
reason for it is that the routing algorithm BATMAN_V was selected and
batadv_schedule_bat_ogm was not yet called for this interface. This slave
interface still has to be set to BATADV_IF_INACTIVE or the batman-adv
interface will never reduce its usage counter and thus never gets shutdown.
This problem can be simulated via:
$ modprobe dummy
$ modprobe batman-adv routing_algo=BATMAN_V
$ ip link add bat0 type batadv
$ ip link set dummy0 master bat0
$ ip link set dummy0 up
$ ip link del bat0
unregister_netdevice: waiting for bat0 to become free. Usage count = 3
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The batman-adv source code is the only place in the kernel which uses the
*_free_ref naming scheme for the *_put functions. Changing it to *_put
makes it more consistent and makes it easier to understand the connection
to the *_get functions.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
batman-adv checks in different situation if a new device is already on top
of a different batman-adv device. This is done by getting the iflink of a
device and all its parent. It assumes that this iflink is always a parent
device in an acyclic graph. But this assumption is broken by devices like
veth which are actually a pair of two devices linked to each other. The
recursive check would therefore get veth0 when calling dev_get_iflink on
veth1. And it gets veth0 when calling dev_get_iflink with veth1.
Creating a veth pair and loading batman-adv freezes parts of the system
ip link add veth0 type veth peer name veth1
modprobe batman-adv
An RCU stall will be detected on the system which cannot be fixed.
INFO: rcu_sched self-detected stall on CPU
1: (5264 ticks this GP) idle=3e9/140000000000001/0
softirq=144683/144686 fqs=5249
(t=5250 jiffies g=46 c=45 q=43)
Task dump for CPU 1:
insmod R running task 0 247 245 0x00000008
ffffffff8151f140 ffffffff8107888e ffff88000fd141c0 ffffffff8151f140
0000000000000000 ffffffff81552df0 ffffffff8107b420 0000000000000001
ffff88000e3fa700 ffffffff81540b00 ffffffff8107d667 0000000000000001
Call Trace:
<IRQ> [<ffffffff8107888e>] ? rcu_dump_cpu_stacks+0x7e/0xd0
[<ffffffff8107b420>] ? rcu_check_callbacks+0x3f0/0x6b0
[<ffffffff8107d667>] ? hrtimer_run_queues+0x47/0x180
[<ffffffff8107cf9d>] ? update_process_times+0x2d/0x50
[<ffffffff810873fb>] ? tick_handle_periodic+0x1b/0x60
[<ffffffff810290ae>] ? smp_trace_apic_timer_interrupt+0x5e/0x90
[<ffffffff813bbae2>] ? apic_timer_interrupt+0x82/0x90
<EOI> [<ffffffff812c3fd7>] ? __dev_get_by_index+0x37/0x40
[<ffffffffa0031f3e>] ? batadv_hard_if_event+0xee/0x3a0 [batman_adv]
[<ffffffff812c5801>] ? register_netdevice_notifier+0x81/0x1a0
[...]
This can be avoided by checking if two devices are each others parent and
stopping the check in this situation.
Fixes: b7eddd0b3950 ("batman-adv: prevent using any virtual device created on batman-adv as hard-interface")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
[sven@narfation.org: rewritten description, extracted fix]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
batman-adv uses a self-written reference implementation which is just based
on atomic_t. This is less obvious when reading the code than kref and
therefore increases the change that the reference counting will be missed.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
The references to the network device should be dropped inside the release
function for batadv_hard_iface similar to what is done with the batman-adv
internal datastructures.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <a@unstable.cc>
|
|
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
A network interface can change type. It may change from a type which
batman does not support, e.g. hdlc, to one it does, e.g. hdlc-eth.
When an interface changes type, it sends two notifications. Handle
these notifications.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sometimes the drivers and other code would find it handy to know some
internal information about upper device being changed. So allow upper-code
to pass information down to notifier listeners during linking.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eliminate netdev_master_upper_dev_link_private and pass priv directly as
a parameter of netdev_master_upper_dev_link.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The maximum of hard_header_len and maximum of all needed_(head|tail)room of
all slave interfaces of a batman-adv device must be used to define the
batman-adv device needed_(head|tail)room. This is required to avoid too
small buffer problems when these slave devices try to send the encapsulated
packet in a tx path without the possibility to resize the skbuff.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
In batadv_hardif_disable_interface() there is a call to
batadv_softif_destroy_sysfs() which in turns invokes
unregister_netdevice() on the soft_iface.
After this point we cannot rely on the soft_iface object
anymore because it might get free'd by the netdev periodic
routine at any time.
For this reason the netdev_upper_dev_unlink(.., soft_iface) call
is moved before the invocation of batadv_softif_destroy_sysfs() so
that we can be sure that the soft_iface object is still valid.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The header files could not be build indepdent from each other. This is
happened because headers didn't include the files for things they've used.
This was problematic because the success of a build depended on the
knowledge about the right order of local includes.
Also source files were not including everything they've used explicitly.
Instead they required that transitive includes are always stable. This is
problematic because some transitive includes are not obvious, depend on
config settings and may not be stable in the future.
The order for include blocks are:
* primary headers (main.h and the *.h file of a *.c file)
* global linux headers
* required local headers
* extra forward declarations for pointers in function/struct declarations
The only exceptions are linux/bitops.h and linux/if_ether.h in packet.h.
This header file is shared with userspace applications like batctl and must
therefore build together with userspace applications. The header
linux/bitops.h is not part of the uapi headers and linux/if_ether.h
conflicts with the musl implementation of netinet/if_ether.h. The
maintainers rejected the use of __KERNEL__ preprocessor checks and thus
these two headers are only in main.h. All files using packet.h first have
to include main.h to work correctly.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The goal of this patch is to prepare the removal of the iflink field. It
introduces a new ndo function, which will be implemented by virtual interfaces.
There is no functional change into this patch. All readers of iflink field
now call dev_get_iflink().
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
batman tries to search dev->iflink to check if it's a batman interface,
but ->iflink could be 0, which is not a valid ifindex. It should just
avoid iflink == 0 case.
Reported-by: Jet Chen <jet.chen@intel.com>
Tested-by: Jet Chen <jet.chen@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Antonio Quartulli <antonio@open-mesh.com>
Cc: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current MTU computation always returns a value
smaller than 1500bytes even if the real interfaces
have an MTU large enough to compensate the batman-adv
overhead.
Fix the computation by properly returning the highest
admitted value.
Introduced by a19d3d85e1b854e4a483a55d740a42458085560d
("batman-adv: limit local translation table max size")
Reported-by: Russell Senior <russell@personaltelco.net>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The following call chains indicate that batadv_is_on_batman_iface()
is always under rtnl_lock protection as call_netdevice_notifier()
is protected by rtnl_lock. So if __dev_get_by_index() rather than
dev_get_by_index() is used to find interface handler in it, this
would help us avoid to change interface reference counter.
call_netdevice_notifier()
batadv_hard_if_event()
batadv_hardif_add_interface()
batadv_is_valid_iface()
batadv_is_on_batman_iface()
Cc: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
To show information per interface, add a debugfs hardif structure
similar to the system in sysfs. Hard interface folders will be created
in "$debugfs/batman-adv/". Files are not yet added.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
