| Age | Commit message (Collapse) | Author |
|---|
|
Commit 6afcf8ef0ca0 ("mm, compaction: fix NR_ISOLATED_* stats for pfn
based migration") moved the dec_node_page_state() call (along with the
page_is_file_cache() call) to after putback_lru_page().
But page_is_file_cache() can change after putback_lru_page() is called,
so it should be called before putback_lru_page(), as it was before that
patch, to prevent NR_ISOLATE_* stats from going negative.
Without this fix, non-CONFIG_SMP kernels end up hanging in the
while(too_many_isolated()) { congestion_wait() } loop in
shrink_active_list() due to the negative stats.
Mem-Info:
active_anon:32567 inactive_anon:121 isolated_anon:1
active_file:6066 inactive_file:6639 isolated_file:4294967295
^^^^^^^^^^
unevictable:0 dirty:115 writeback:0 unstable:0
slab_reclaimable:2086 slab_unreclaimable:3167
mapped:3398 shmem:18366 pagetables:1145 bounce:0
free:1798 free_pcp:13 free_cma:0
Fixes: 6afcf8ef0ca0 ("mm, compaction: fix NR_ISOLATED_* stats for pfn based migration")
Link: http://lkml.kernel.org/r/1492683865-27549-1-git-send-email-rabin.vincent@axis.com
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Ming Ling <ming.ling@spreadtrum.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This reverts commit 374ad05ab64.
While the patch worked great for userspace allocations, the fact that
softirq loses the per-cpu allocator caused problems. It needs to be
redone taking into account that a separate list is needed for hard/soft
IRQs or alternatively find a cheap way of detecting reentry due to an
interrupt. Both are possible but sufficiently tricky that it shouldn't
be rushed.
Jesper had one method for allowing softirqs but reported that the cost
was high enough that it performed similarly to a plain revert. His
figures for netperf TCP_STREAM were as follows
Baseline v4.10.0 : 60316 Mbit/s
Current 4.11.0-rc6: 47491 Mbit/s
Jesper's patch : 60662 Mbit/s
This patch : 60106 Mbit/s
As this is a regression, I wish to revert to noirq allocator for now and
go back to the drawing board.
Link: http://lkml.kernel.org/r/20170415145350.ixy7vtrzdzve57mh@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Reported-by: Tariq Toukan <ttoukan.linux@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Geert has reported a freeze during PM resume and some additional
debugging has shown that the device_resume worker cannot make a forward
progress because it waits for an event which is stuck waiting in
drain_all_pages:
INFO: task kworker/u4:0:5 blocked for more than 120 seconds.
Not tainted 4.11.0-rc7-koelsch-00029-g005882e53d62f25d-dirty #3476
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u4:0 D 0 5 2 0x00000000
Workqueue: events_unbound async_run_entry_fn
__schedule
schedule
schedule_timeout
wait_for_common
dpm_wait_for_superior
device_resume
async_resume
async_run_entry_fn
process_one_work
worker_thread
kthread
[...]
bash D 0 1703 1694 0x00000000
__schedule
schedule
schedule_timeout
wait_for_common
flush_work
drain_all_pages
start_isolate_page_range
alloc_contig_range
cma_alloc
__alloc_from_contiguous
cma_allocator_alloc
__dma_alloc
arm_dma_alloc
sh_eth_ring_init
sh_eth_open
sh_eth_resume
dpm_run_callback
device_resume
dpm_resume
dpm_resume_end
suspend_devices_and_enter
pm_suspend
state_store
kernfs_fop_write
__vfs_write
vfs_write
SyS_write
[...]
Showing busy workqueues and worker pools:
[...]
workqueue mm_percpu_wq: flags=0xc
pwq 2: cpus=1 node=0 flags=0x0 nice=0 active=0/0
delayed: drain_local_pages_wq, vmstat_update
pwq 0: cpus=0 node=0 flags=0x0 nice=0 active=0/0
delayed: drain_local_pages_wq BAR(1703), vmstat_update
Tetsuo has properly noted that mm_percpu_wq is created as WQ_FREEZABLE
so it is frozen this early during resume so we are effectively
deadlocked. Fix this by dropping WQ_FREEZABLE when creating
mm_percpu_wq. We really want to have it operational all the time.
Fixes: ce612879ddc7 ("mm: move pcp and lru-pcp draining into single wq")
Reported-and-tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Debugged-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now 64K page system, zsamlloc has 257 classes so 8 class bit is not
enough. With that, it corrupts the system when zsmalloc stores
65536byte data(ie, index number 256) so that this patch increases class
bit for simple fix for stable backport. We should clean up this mess
soon.
index size
0 32
1 288
..
..
204 52256
256 65536
Fixes: 3783689a1 ("zsmalloc: introduce zspage structure")
Link: http://lkml.kernel.org/r/1492042622-12074-3-git-send-email-minchan@kernel.org
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Both MADV_DONTNEED and MADV_FREE handled with down_read(mmap_sem).
It's critical to not clear pmd intermittently while handling MADV_FREE
to avoid race with MADV_DONTNEED:
CPU0: CPU1:
madvise_free_huge_pmd()
pmdp_huge_get_and_clear_full()
madvise_dontneed()
zap_pmd_range()
pmd_trans_huge(*pmd) == 0 (without ptl)
// skip the pmd
set_pmd_at();
// pmd is re-established
It results in MADV_DONTNEED skipping the pmd, leaving it not cleared.
It violates MADV_DONTNEED interface and can result is userspace
misbehaviour.
Basically it's the same race as with numa balancing in
change_huge_pmd(), but a bit simpler to mitigate: we don't need to
preserve dirty/young flags here due to MADV_FREE functionality.
[kirill.shutemov@linux.intel.com: Urgh... Power is special again]
Link: http://lkml.kernel.org/r/20170303102636.bhd2zhtpds4mt62a@black.fi.intel.com
Link: http://lkml.kernel.org/r/20170302151034.27829-4-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In case prot_numa, we are under down_read(mmap_sem). It's critical to
not clear pmd intermittently to avoid race with MADV_DONTNEED which is
also under down_read(mmap_sem):
CPU0: CPU1:
change_huge_pmd(prot_numa=1)
pmdp_huge_get_and_clear_notify()
madvise_dontneed()
zap_pmd_range()
pmd_trans_huge(*pmd) == 0 (without ptl)
// skip the pmd
set_pmd_at();
// pmd is re-established
The race makes MADV_DONTNEED miss the huge pmd and don't clear it
which may break userspace.
Found by code analysis, never saw triggered.
Link: http://lkml.kernel.org/r/20170302151034.27829-3-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "thp: fix few MADV_DONTNEED races"
For MADV_DONTNEED to work properly with huge pages, it's critical to not
clear pmd intermittently unless you hold down_write(mmap_sem).
Otherwise MADV_DONTNEED can miss the THP which can lead to userspace
breakage.
See example of such race in commit message of patch 2/4.
All these races are found by code inspection. I haven't seen them
triggered. I don't think it's worth to apply them to stable@.
This patch (of 4):
Restructure code in preparation for a fix.
Link: http://lkml.kernel.org/r/20170302151034.27829-2-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Stress testing of the current z3fold implementation on a 8-core system
revealed it was possible that a z3fold page deleted from its unbuddied
list in z3fold_alloc() would be put on another unbuddied list by
z3fold_free() while z3fold_alloc() is still processing it. This has
been introduced with commit 5a27aa822 ("z3fold: add kref refcounting")
due to the removal of special handling of a z3fold page not on any list
in z3fold_free().
To fix this, the z3fold page lock should be taken in z3fold_alloc()
before the pool lock is released. To avoid deadlocking, we just try to
lock the page as soon as we get a hold of it, and if trylock fails, we
drop this page and take the next one.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: <Oleksiy.Avramchenko@sony.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In the case that compat_get_bitmap fails we do not want to copy the
bitmap to the user as it will contain uninitialized stack data and leak
sensitive data.
Signed-off-by: Chris Salls <salls@cs.ucsb.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We currently have 2 specific WQ_RECLAIM workqueues in the mm code.
vmstat_wq for updating pcp stats and lru_add_drain_wq dedicated to drain
per cpu lru caches. This seems more than necessary because both can run
on a single WQ. Both do not block on locks requiring a memory
allocation nor perform any allocations themselves. We will save one
rescuer thread this way.
On the other hand drain_all_pages() queues work on the system wq which
doesn't have rescuer and so this depend on memory allocation (when all
workers are stuck allocating and new ones cannot be created).
Initially we thought this would be more of a theoretical problem but
Hugh Dickins has reported:
: 4.11-rc has been giving me hangs after hours of swapping load. At
: first they looked like memory leaks ("fork: Cannot allocate memory");
: but for no good reason I happened to do "cat /proc/sys/vm/stat_refresh"
: before looking at /proc/meminfo one time, and the stat_refresh stuck
: in D state, waiting for completion of flush_work like many kworkers.
: kthreadd waiting for completion of flush_work in drain_all_pages().
This worker should be using WQ_RECLAIM as well in order to guarantee a
forward progress. We can reuse the same one as for lru draining and
vmstat.
Link: http://lkml.kernel.org/r/20170307131751.24936-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Suggested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Tested-by: Yang Li <pku.leo@gmail.com>
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We got need_resched() warnings in swap_cgroup_swapoff() because
swap_cgroup_ctrl[type].length is particularly large.
Reschedule when needed.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1704061315270.80559@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Setting thp defrag mode of "defer+madvise" actually sets "defer" in the
kernel due to the name similarity and the out-of-order way the string is
checked in defrag_store().
Check the string in the correct order so that
TRANSPARENT_HUGEPAGE_DEFRAG_KSWAPD_OR_MADV_FLAG is set appropriately for
"defer+madvise".
Fixes: 21440d7eb904 ("mm, thp: add new defer+madvise defrag option")
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1704051814420.137626@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes: 11fb998986a72a ("mm: move most file-based accounting to the node")
Link: http://lkml.kernel.org/r/1490377730.30219.2.camel@beget.ru
Signed-off-by: Alexander Polyakov <apolyakov@beget.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Doug Smythies reports oops with KSM in this backtrace, I've been seeing
the same:
page_vma_mapped_walk+0xe6/0x5b0
page_referenced_one+0x91/0x1a0
rmap_walk_ksm+0x100/0x190
rmap_walk+0x4f/0x60
page_referenced+0x149/0x170
shrink_active_list+0x1c2/0x430
shrink_node_memcg+0x67a/0x7a0
shrink_node+0xe1/0x320
kswapd+0x34b/0x720
Just as observed in commit 4b0ece6fa016 ("mm: migrate: fix
remove_migration_pte() for ksm pages"), you cannot use page->index
calculations on ksm pages.
page_vma_mapped_walk() is relying on __vma_address(), where a ksm page
can lead it off the end of the page table, and into whatever nonsense is
in the next page, ending as an oops inside check_pte()'s pte_page().
KSM tells page_vma_mapped_walk() exactly where to look for the page, it
does not need any page->index calculation: and that's so also for all
the normal and file and anon pages - just not for THPs and their
subpages. Get out early in most cases: instead of a PageKsm test, move
down the earlier not-THP-page test, as suggested by Kirill.
I'm also slightly worried that this loop can stray into other vmas, so
added a vm_end test to prevent surprises; though I have not imagined
anything worse than a very contrived case, in which a page mlocked in
the next vma might be reclaimed because it is not mlocked in this vma.
Fixes: ace71a19cec5 ("mm: introduce page_vma_mapped_walk()")
Link: http://lkml.kernel.org/r/alpine.LSU.2.11.1704031104400.1118@eggly.anvils
Signed-off-by: Hugh Dickins <hughd@google.com>
Reported-by: Doug Smythies <dsmythies@telus.net>
Tested-by: Doug Smythies <dsmythies@telus.net>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Changes to hugetlbfs reservation maps is a two step process. The first
step is a call to region_chg to determine what needs to be changed, and
prepare that change. This should be followed by a call to call to
region_add to commit the change, or region_abort to abort the change.
The error path in hugetlb_reserve_pages called region_abort after a
failed call to region_chg. As a result, the adds_in_progress counter in
the reservation map is off by 1. This is caught by a VM_BUG_ON in
resv_map_release when the reservation map is freed.
syzkaller fuzzer (when using an injected kmalloc failure) found this
bug, that resulted in the following:
kernel BUG at mm/hugetlb.c:742!
Call Trace:
hugetlbfs_evict_inode+0x7b/0xa0 fs/hugetlbfs/inode.c:493
evict+0x481/0x920 fs/inode.c:553
iput_final fs/inode.c:1515 [inline]
iput+0x62b/0xa20 fs/inode.c:1542
hugetlb_file_setup+0x593/0x9f0 fs/hugetlbfs/inode.c:1306
newseg+0x422/0xd30 ipc/shm.c:575
ipcget_new ipc/util.c:285 [inline]
ipcget+0x21e/0x580 ipc/util.c:639
SYSC_shmget ipc/shm.c:673 [inline]
SyS_shmget+0x158/0x230 ipc/shm.c:657
entry_SYSCALL_64_fastpath+0x1f/0xc2
RIP: resv_map_release+0x265/0x330 mm/hugetlb.c:742
Link: http://lkml.kernel.org/r/1490821682-23228-1-git-send-email-mike.kravetz@oracle.com
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Disable kasan after the first report. There are several reasons for
this:
- Single bug quite often has multiple invalid memory accesses causing
storm in the dmesg.
- Write OOB access might corrupt metadata so the next report will print
bogus alloc/free stacktraces.
- Reports after the first easily could be not bugs by itself but just
side effects of the first one.
Given that multiple reports usually only do harm, it makes sense to
disable kasan after the first one. If user wants to see all the
reports, the boot-time parameter kasan_multi_shot must be used.
[aryabinin@virtuozzo.com: wrote changelog and doc, added missing include]
Link: http://lkml.kernel.org/r/20170323154416.30257-1-aryabinin@virtuozzo.com
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A section name for .data..ro_after_init was added by both:
commit d07a980c1b8d ("s390: add proper __ro_after_init support")
and
commit d7c19b066dcf ("mm: kmemleak: scan .data.ro_after_init")
The latter adds incorrect wrapping around the existing s390 section, and
came later. I'd prefer the s390 naming, so this moves the s390-specific
name up to the asm-generic/sections.h and renames the section as used by
kmemleak (and in the future, kernel/extable.c).
Link: http://lkml.kernel.org/r/20170327192213.GA129375@beast
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> [s390 parts]
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Eddie Kovsky <ewk@edkovsky.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I found the race condition which triggers the following bug when
move_pages() and soft offline are called on a single hugetlb page
concurrently.
Soft offlining page 0x119400 at 0x700000000000
BUG: unable to handle kernel paging request at ffffea0011943820
IP: follow_huge_pmd+0x143/0x190
PGD 7ffd2067
PUD 7ffd1067
PMD 0
[61163.582052] Oops: 0000 [#1] SMP
Modules linked in: binfmt_misc ppdev virtio_balloon parport_pc pcspkr i2c_piix4 parport i2c_core acpi_cpufreq ip_tables xfs libcrc32c ata_generic pata_acpi virtio_blk 8139too crc32c_intel ata_piix serio_raw libata virtio_pci 8139cp virtio_ring virtio mii floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: cap_check]
CPU: 0 PID: 22573 Comm: iterate_numa_mo Tainted: P OE 4.11.0-rc2-mm1+ #2
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:follow_huge_pmd+0x143/0x190
RSP: 0018:ffffc90004bdbcd0 EFLAGS: 00010202
RAX: 0000000465003e80 RBX: ffffea0004e34d30 RCX: 00003ffffffff000
RDX: 0000000011943800 RSI: 0000000000080001 RDI: 0000000465003e80
RBP: ffffc90004bdbd18 R08: 0000000000000000 R09: ffff880138d34000
R10: ffffea0004650000 R11: 0000000000c363b0 R12: ffffea0011943800
R13: ffff8801b8d34000 R14: ffffea0000000000 R15: 000077ff80000000
FS: 00007fc977710740(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffea0011943820 CR3: 000000007a746000 CR4: 00000000001406f0
Call Trace:
follow_page_mask+0x270/0x550
SYSC_move_pages+0x4ea/0x8f0
SyS_move_pages+0xe/0x10
do_syscall_64+0x67/0x180
entry_SYSCALL64_slow_path+0x25/0x25
RIP: 0033:0x7fc976e03949
RSP: 002b:00007ffe72221d88 EFLAGS: 00000246 ORIG_RAX: 0000000000000117
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fc976e03949
RDX: 0000000000c22390 RSI: 0000000000001400 RDI: 0000000000005827
RBP: 00007ffe72221e00 R08: 0000000000c2c3a0 R09: 0000000000000004
R10: 0000000000c363b0 R11: 0000000000000246 R12: 0000000000400650
R13: 00007ffe72221ee0 R14: 0000000000000000 R15: 0000000000000000
Code: 81 e4 ff ff 1f 00 48 21 c2 49 c1 ec 0c 48 c1 ea 0c 4c 01 e2 49 bc 00 00 00 00 00 ea ff ff 48 c1 e2 06 49 01 d4 f6 45 bc 04 74 90 <49> 8b 7c 24 20 40 f6 c7 01 75 2b 4c 89 e7 8b 47 1c 85 c0 7e 2a
RIP: follow_huge_pmd+0x143/0x190 RSP: ffffc90004bdbcd0
CR2: ffffea0011943820
---[ end trace e4f81353a2d23232 ]---
Kernel panic - not syncing: Fatal exception
Kernel Offset: disabled
This bug is triggered when pmd_present() returns true for non-present
hugetlb, so fixing the present check in follow_huge_pmd() prevents it.
Using pmd_present() to determine present/non-present for hugetlb is not
correct, because pmd_present() checks multiple bits (not only
_PAGE_PRESENT) for historical reason and it can misjudge hugetlb state.
Fixes: e66f17ff7177 ("mm/hugetlb: take page table lock in follow_huge_pmd()")
Link: http://lkml.kernel.org/r/1490149898-20231-1-git-send-email-n-horiguchi@ah.jp.nec.com
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: <stable@vger.kernel.org> [4.0+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 0a6b76dd23fa ("mm: workingset: make shadow node shrinker memcg
aware") enabled cgroup-awareness in the shadow node shrinker, but forgot
to also enable cgroup-awareness in the list_lru the shadow nodes sit on.
Consequently, all shadow nodes are sitting on a global (per-NUMA node)
list, while the shrinker applies the limits according to the amount of
cache in the cgroup its shrinking. The result is excessive pressure on
the shadow nodes from cgroups that have very little cache.
Enable memcg-mode on the shadow node LRUs, such that per-cgroup limits
are applied to per-cgroup lists.
Fixes: 0a6b76dd23fa ("mm: workingset: make shadow node shrinker memcg aware")
Link: http://lkml.kernel.org/r/20170322005320.8165-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vladimir Davydov <vdavydov@tarantool.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: <stable@vger.kernel.org> [4.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Huge pages are accounted as single units in the memcg's "file_mapped"
counter. Account the correct number of base pages, like we do in the
corresponding node counter.
Link: http://lkml.kernel.org/r/20170322005111.3156-1-hannes@cmpxchg.org
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: <stable@vger.kernel.org> [4.8+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Yang Li has reported that drain_all_pages triggers a WARN_ON which means
that this function is called earlier than the mm_percpu_wq is
initialized on arm64 with CMA configured:
WARNING: CPU: 2 PID: 1 at mm/page_alloc.c:2423 drain_all_pages+0x244/0x25c
Modules linked in:
CPU: 2 PID: 1 Comm: swapper/0 Not tainted 4.11.0-rc1-next-20170310-00027-g64dfbc5 #127
Hardware name: Freescale Layerscape 2088A RDB Board (DT)
task: ffffffc07c4a6d00 task.stack: ffffffc07c4a8000
PC is at drain_all_pages+0x244/0x25c
LR is at start_isolate_page_range+0x14c/0x1f0
[...]
drain_all_pages+0x244/0x25c
start_isolate_page_range+0x14c/0x1f0
alloc_contig_range+0xec/0x354
cma_alloc+0x100/0x1fc
dma_alloc_from_contiguous+0x3c/0x44
atomic_pool_init+0x7c/0x208
arm64_dma_init+0x44/0x4c
do_one_initcall+0x38/0x128
kernel_init_freeable+0x1a0/0x240
kernel_init+0x10/0xfc
ret_from_fork+0x10/0x20
Fix this by moving the whole setup_vmstat which is an initcall right now
to init_mm_internals which will be called right after the WQ subsystem
is initialized.
Link: http://lkml.kernel.org/r/20170315164021.28532-1-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Reported-by: Yang Li <pku.leo@gmail.com>
Tested-by: Yang Li <pku.leo@gmail.com>
Tested-by: Xiaolong Ye <xiaolong.ye@intel.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
I found that calling page migration for ksm pages causes the following
bug:
page:ffffea0004d51180 count:2 mapcount:2 mapping:ffff88013c785141 index:0x913
flags: 0x57ffffc0040068(uptodate|lru|active|swapbacked)
raw: 0057ffffc0040068 ffff88013c785141 0000000000000913 0000000200000001
raw: ffffea0004d5f9e0 ffffea0004d53f60 0000000000000000 ffff88007d81b800
page dumped because: VM_BUG_ON_PAGE(!PageLocked(page))
page->mem_cgroup:ffff88007d81b800
------------[ cut here ]------------
kernel BUG at /src/linux-dev/mm/rmap.c:1086!
invalid opcode: 0000 [#1] SMP
Modules linked in: ppdev parport_pc virtio_balloon i2c_piix4 pcspkr parport i2c_core acpi_cpufreq ip_tables xfs libcrc32c ata_generic pata_acpi ata_piix 8139too libata virtio_blk 8139cp crc32c_intel mii virtio_pci virtio_ring serio_raw virtio floppy dm_mirror dm_region_hash dm_log dm_mod
CPU: 0 PID: 3162 Comm: bash Not tainted 4.11.0-rc2-mm1+ #1
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:do_page_add_anon_rmap+0x1ba/0x260
RSP: 0018:ffffc90002473b30 EFLAGS: 00010282
RAX: 0000000000000021 RBX: ffffea0004d51180 RCX: 0000000000000006
RDX: 0000000000000000 RSI: 0000000000000082 RDI: ffff88007dc0dfe0
RBP: ffffc90002473b58 R08: 00000000fffffffe R09: 00000000000001c1
R10: 0000000000000005 R11: 00000000000001c0 R12: ffff880139ab3d80
R13: 0000000000000000 R14: 0000700000000200 R15: 0000160000000000
FS: 00007f5195f50740(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fd450287000 CR3: 000000007a08e000 CR4: 00000000001406f0
Call Trace:
page_add_anon_rmap+0x18/0x20
remove_migration_pte+0x220/0x2c0
rmap_walk_ksm+0x143/0x220
rmap_walk+0x55/0x60
remove_migration_ptes+0x53/0x80
migrate_pages+0x8ed/0xb60
soft_offline_page+0x309/0x8d0
store_soft_offline_page+0xaf/0xf0
dev_attr_store+0x18/0x30
sysfs_kf_write+0x3a/0x50
kernfs_fop_write+0xff/0x180
__vfs_write+0x37/0x160
vfs_write+0xb2/0x1b0
SyS_write+0x55/0xc0
do_syscall_64+0x67/0x180
entry_SYSCALL64_slow_path+0x25/0x25
RIP: 0033:0x7f51956339e0
RSP: 002b:00007ffcfa0dffc8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007f51956339e0
RDX: 000000000000000c RSI: 00007f5195f53000 RDI: 0000000000000001
RBP: 00007f5195f53000 R08: 000000000000000a R09: 00007f5195f50740
R10: 000000000000000b R11: 0000000000000246 R12: 00007f5195907400
R13: 000000000000000c R14: 0000000000000001 R15: 0000000000000000
Code: fe ff ff 48 81 c2 00 02 00 00 48 89 55 d8 e8 2e c3 fd ff 48 8b 55 d8 e9 42 ff ff ff 48 c7 c6 e0 52 a1 81 48 89 df e8 46 ad fe ff <0f> 0b 48 83 e8 01 e9 7f fe ff ff 48 83 e8 01 e9 96 fe ff ff 48
RIP: do_page_add_anon_rmap+0x1ba/0x260 RSP: ffffc90002473b30
---[ end trace a679d00f4af2df48 ]---
Kernel panic - not syncing: Fatal exception
Kernel Offset: disabled
---[ end Kernel panic - not syncing: Fatal exception
The problem is in the following lines:
new = page - pvmw.page->index +
linear_page_index(vma, pvmw.address);
The 'new' is calculated with 'page' which is given by the caller as a
destination page and some offset adjustment for thp. But this doesn't
properly work for ksm pages because pvmw.page->index doesn't change for
each address but linear_page_index() changes, which means that 'new'
points to different pages for each addresses backed by the ksm page. As
a result, we try to set totally unrelated pages as destination pages,
and that causes kernel crash.
This patch fixes the miscalculation and makes ksm page migration work
fine.
Fixes: 3fe87967c536 ("mm: convert remove_migration_pte() to use page_vma_mapped_walk()")
Link: http://lkml.kernel.org/r/1489717683-29905-1-git-send-email-n-horiguchi@ah.jp.nec.com
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before commit 452b94b8c8c7 ("mm/swap: don't BUG_ON() due to
uninitialized swap slot cache"), the following bug is reported,
------------[ cut here ]------------
kernel BUG at mm/swap_slots.c:270!
invalid opcode: 0000 [#1] SMP
CPU: 5 PID: 1745 Comm: (sd-pam) Not tainted 4.11.0-rc1-00243-g24c534bb161b #1
Hardware name: System manufacturer System Product Name/Z170-K, BIOS 1803 05/06/2016
RIP: 0010:free_swap_slot+0xba/0xd0
Call Trace:
swap_free+0x36/0x40
do_swap_page+0x360/0x6d0
__handle_mm_fault+0x880/0x1080
handle_mm_fault+0xd0/0x240
__do_page_fault+0x232/0x4d0
do_page_fault+0x20/0x70
page_fault+0x22/0x30
---[ end trace aefc9ede53e0ab21 ]---
This is raised by the BUG_ON(!swap_slot_cache_initialized) in
free_swap_slot(). This is incorrect, because even if the swap slots
cache fails to be initialized, the swap should operate properly without
the swap slots cache. And the use_swap_slot_cache check later in the
function will protect the uninitialized swap slots cache case.
In commit 452b94b8c8c7, the BUG_ON() is replaced by WARN_ON_ONCE(). In
the patch, the WARN_ON_ONCE() is removed too.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: "Huang, Ying" <ying.huang@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This BUG_ON() triggered for me once at shutdown, and I don't see a
reason for the check. The code correctly checks whether the swap slot
cache is usable or not, so an uninitialized swap slot cache is not
actually problematic afaik.
I've temporarily just switched the BUG_ON() to a WARN_ON_ONCE(), since
I'm not sure why that seemingly pointless check was there. I suspect
the real fix is to just remove it entirely, but for now we'll warn about
it but not bring the machine down.
Cc: "Huang, Ying" <ying.huang@intel.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit bfc8c90139eb ("mem-hotplug: implement get/put_online_mems")
introduced new functions get/put_online_mems() and mem_hotplug_begin/end()
in order to allow similar semantics for memory hotplug like for cpu
hotplug.
The corresponding functions for cpu hotplug are get/put_online_cpus()
and cpu_hotplug_begin/done() for cpu hotplug.
The commit however missed to introduce functions that would serialize
memory hotplug operations like they are done for cpu hotplug with
cpu_maps_update_begin/done().
This basically leaves mem_hotplug.active_writer unprotected and allows
concurrent writers to modify it, which may lead to problems as outlined
by commit f931ab479dd2 ("mm: fix devm_memremap_pages crash, use
mem_hotplug_{begin, done}").
That commit was extended again with commit b5d24fda9c3d ("mm,
devm_memremap_pages: hold device_hotplug lock over mem_hotplug_{begin,
done}") which serializes memory hotplug operations for some call sites
by using the device_hotplug lock.
In addition with commit 3fc21924100b ("mm: validate device_hotplug is held
for memory hotplug") a sanity check was added to mem_hotplug_begin() to
verify that the device_hotplug lock is held.
This in turn triggers the following warning on s390:
WARNING: CPU: 6 PID: 1 at drivers/base/core.c:643 assert_held_device_hotplug+0x4a/0x58
Call Trace:
assert_held_device_hotplug+0x40/0x58)
mem_hotplug_begin+0x34/0xc8
add_memory_resource+0x7e/0x1f8
add_memory+0xda/0x130
add_memory_merged+0x15c/0x178
sclp_detect_standby_memory+0x2ae/0x2f8
do_one_initcall+0xa2/0x150
kernel_init_freeable+0x228/0x2d8
kernel_init+0x2a/0x140
kernel_thread_starter+0x6/0xc
One possible fix would be to add more lock_device_hotplug() and
unlock_device_hotplug() calls around each call site of
mem_hotplug_begin/end(). But that would give the device_hotplug lock
additional semantics it better should not have (serialize memory hotplug
operations).
Instead add a new memory_add_remove_lock which has the similar semantics
like cpu_add_remove_lock for cpu hotplug.
To keep things hopefully a bit easier the lock will be locked and unlocked
within the mem_hotplug_begin/end() functions.
Link: http://lkml.kernel.org/r/20170314125226.16779-2-heiko.carstens@de.ibm.com
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When vmalloc() fails it prints a very lengthy message with all the
details about memory consumption assuming that it happened due to OOM.
However, vmalloc() can also fail due to fatal signal pending. In such
case the message is quite confusing because it suggests that it is OOM
but the numbers suggest otherwise. The messages can also pollute
console considerably.
Don't warn when vmalloc() fails due to fatal signal pending.
Link: http://lkml.kernel.org/r/20170313114425.72724-1-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Reviewed-by: Matthew Wilcox <mawilcox@microsoft.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commmit 5a27aa822029 ("z3fold: add kref refcounting") introduced a bug
in z3fold_reclaim_page() with function exit that may leave pool->lock
spinlock held. Here comes the trivial fix.
Fixes: 5a27aa822029 ("z3fold: add kref refcounting")
Link: http://lkml.kernel.org/r/20170311222239.7b83d8e7ef1914e05497649f@gmail.com
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Cc: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu
Pull percpu fixes from Tejun Heo:
- the allocation path was updating pcpu_nr_empty_pop_pages without the
required locking which can lead to incorrect handling of empty chunks
(e.g. keeping too many around), which is buggy but shouldn't lead to
critical failures. Fixed by adding the locking
- a trivial patch to drop an unused param from pcpu_get_pages()
* 'for-4.11-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: remove unused chunk_alloc parameter from pcpu_get_pages()
percpu: acquire pcpu_lock when updating pcpu_nr_empty_pop_pages
|
|
gup_p4d_range() should call gup_pud_range(), not itself.
[ This was not noticed on x86: this is the HAVE_GENERIC_RCU_GUP code
used by arm[64] and powerpc - Linus ]
Fixes: c2febafc6773 ("mm: convert generic code to 5-level paging")
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reported-by: Anton Blanchard <anton@samba.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge 5-level page table prep from Kirill Shutemov:
"Here's relatively low-risk part of 5-level paging patchset. Merging it
now will make x86 5-level paging enabling in v4.12 easier.
The first patch is actually x86-specific: detect 5-level paging
support. It boils down to single define.
The rest of patchset converts Linux MMU abstraction from 4- to 5-level
paging.
Enabling of new abstraction in most cases requires adding single line
of code in arch-specific code. The rest is taken care by asm-generic/.
Changes to mm/ code are mostly mechanical: add support for new page
table level -- p4d_t -- where we deal with pud_t now.
v2:
- fix build on microblaze (Michal);
- comment for __ARCH_HAS_5LEVEL_HACK in kasan_populate_zero_shadow();
- acks from Michal"
* emailed patches from Kirill A Shutemov <kirill.shutemov@linux.intel.com>:
mm: introduce __p4d_alloc()
mm: convert generic code to 5-level paging
asm-generic: introduce <asm-generic/pgtable-nop4d.h>
arch, mm: convert all architectures to use 5level-fixup.h
asm-generic: introduce __ARCH_USE_5LEVEL_HACK
asm-generic: introduce 5level-fixup.h
x86/cpufeature: Add 5-level paging detection
|
|
Merge fixes from Andrew Morton:
"26 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (26 commits)
userfaultfd: remove wrong comment from userfaultfd_ctx_get()
fat: fix using uninitialized fields of fat_inode/fsinfo_inode
sh: cayman: IDE support fix
kasan: fix races in quarantine_remove_cache()
kasan: resched in quarantine_remove_cache()
mm: do not call mem_cgroup_free() from within mem_cgroup_alloc()
thp: fix another corner case of munlock() vs. THPs
rmap: fix NULL-pointer dereference on THP munlocking
mm/memblock.c: fix memblock_next_valid_pfn()
userfaultfd: selftest: vm: allow to build in vm/ directory
userfaultfd: non-cooperative: userfaultfd_remove revalidate vma in MADV_DONTNEED
userfaultfd: non-cooperative: fix fork fctx->new memleak
mm/cgroup: avoid panic when init with low memory
drivers/md/bcache/util.h: remove duplicate inclusion of blkdev.h
mm/vmstats: add thp_split_pud event for clarity
include/linux/fs.h: fix unsigned enum warning with gcc-4.2
userfaultfd: non-cooperative: release all ctx in dup_userfaultfd_complete
userfaultfd: non-cooperative: robustness check
userfaultfd: non-cooperative: rollback userfaultfd_exit
x86, mm: unify exit paths in gup_pte_range()
...
|
|
quarantine_remove_cache() frees all pending objects that belong to the
cache, before we destroy the cache itself. However there are currently
two possibilities how it can fail to do so.
First, another thread can hold some of the objects from the cache in
temp list in quarantine_put(). quarantine_put() has a windows of
enabled interrupts, and on_each_cpu() in quarantine_remove_cache() can
finish right in that window. These objects will be later freed into the
destroyed cache.
Then, quarantine_reduce() has the same problem. It grabs a batch of
objects from the global quarantine, then unlocks quarantine_lock and
then frees the batch. quarantine_remove_cache() can finish while some
objects from the cache are still in the local to_free list in
quarantine_reduce().
Fix the race with quarantine_put() by disabling interrupts for the whole
duration of quarantine_put(). In combination with on_each_cpu() in
quarantine_remove_cache() it ensures that quarantine_remove_cache()
either sees the objects in the per-cpu list or in the global list.
Fix the race with quarantine_reduce() by protecting quarantine_reduce()
with srcu critical section and then doing synchronize_srcu() at the end
of quarantine_remove_cache().
I've done some assessment of how good synchronize_srcu() works in this
case. And on a 4 CPU VM I see that it blocks waiting for pending read
critical sections in about 2-3% of cases. Which looks good to me.
I suspect that these races are the root cause of some GPFs that I
episodically hit. Previously I did not have any explanation for them.
BUG: unable to handle kernel NULL pointer dereference at 00000000000000c8
IP: qlist_free_all+0x2e/0xc0 mm/kasan/quarantine.c:155
PGD 6aeea067
PUD 60ed7067
PMD 0
Oops: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
(ftrace buffer empty)
Modules linked in:
CPU: 0 PID: 13667 Comm: syz-executor2 Not tainted 4.10.0+ #60
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task: ffff88005f948040 task.stack: ffff880069818000
RIP: 0010:qlist_free_all+0x2e/0xc0 mm/kasan/quarantine.c:155
RSP: 0018:ffff88006981f298 EFLAGS: 00010246
RAX: ffffea0000ffff00 RBX: 0000000000000000 RCX: ffffea0000ffff1f
RDX: 0000000000000000 RSI: ffff88003fffc3e0 RDI: 0000000000000000
RBP: ffff88006981f2c0 R08: ffff88002fed7bd8 R09: 00000001001f000d
R10: 00000000001f000d R11: ffff88006981f000 R12: ffff88003fffc3e0
R13: ffff88006981f2d0 R14: ffffffff81877fae R15: 0000000080000000
FS: 00007fb911a2d700(0000) GS:ffff88003ec00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000000000c8 CR3: 0000000060ed6000 CR4: 00000000000006f0
Call Trace:
quarantine_reduce+0x10e/0x120 mm/kasan/quarantine.c:239
kasan_kmalloc+0xca/0xe0 mm/kasan/kasan.c:590
kasan_slab_alloc+0x12/0x20 mm/kasan/kasan.c:544
slab_post_alloc_hook mm/slab.h:456 [inline]
slab_alloc_node mm/slub.c:2718 [inline]
kmem_cache_alloc_node+0x1d3/0x280 mm/slub.c:2754
__alloc_skb+0x10f/0x770 net/core/skbuff.c:219
alloc_skb include/linux/skbuff.h:932 [inline]
_sctp_make_chunk+0x3b/0x260 net/sctp/sm_make_chunk.c:1388
sctp_make_data net/sctp/sm_make_chunk.c:1420 [inline]
sctp_make_datafrag_empty+0x208/0x360 net/sctp/sm_make_chunk.c:746
sctp_datamsg_from_user+0x7e8/0x11d0 net/sctp/chunk.c:266
sctp_sendmsg+0x2611/0x3970 net/sctp/socket.c:1962
inet_sendmsg+0x164/0x5b0 net/ipv4/af_inet.c:761
sock_sendmsg_nosec net/socket.c:633 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:643
SYSC_sendto+0x660/0x810 net/socket.c:1685
SyS_sendto+0x40/0x50 net/socket.c:1653
I am not sure about backporting. The bug is quite hard to trigger, I've
seen it few times during our massive continuous testing (however, it
could be cause of some other episodic stray crashes as it leads to
memory corruption...). If it is triggered, the consequences are very
bad -- almost definite bad memory corruption. The fix is non trivial
and has chances of introducing new bugs. I am also not sure how
actively people use KASAN on older releases.
[dvyukov@google.com: - sorted includes[
Link: http://lkml.kernel.org/r/20170309094028.51088-1-dvyukov@google.com
Link: http://lkml.kernel.org/r/20170308151532.5070-1-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Greg Thelen <gthelen@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We see reported stalls/lockups in quarantine_remove_cache() on machines
with large amounts of RAM. quarantine_remove_cache() needs to scan
whole quarantine in order to take out all objects belonging to the
cache. Quarantine is currently 1/32-th of RAM, e.g. on a machine with
256GB of memory that will be 8GB. Moreover quarantine scanning is a
walk over uncached linked list, which is slow.
Add cond_resched() after scanning of each non-empty batch of objects.
Batches are specifically kept of reasonable size for quarantine_put().
On a machine with 256GB of RAM we should have ~512 non-empty batches,
each with 16MB of objects.
Link: http://lkml.kernel.org/r/20170308154239.25440-1-dvyukov@google.com
Signed-off-by: Dmitry Vyukov <dvyukov@google.com>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
mem_cgroup_free() indirectly calls wb_domain_exit() which is not
prepared to deal with a struct wb_domain object that hasn't executed
wb_domain_init(). For instance, the following warning message is
printed by lockdep if alloc_percpu() fails in mem_cgroup_alloc():
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 1 PID: 1950 Comm: mkdir Not tainted 4.10.0+ #151
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
dump_stack+0x67/0x99
register_lock_class+0x36d/0x540
__lock_acquire+0x7f/0x1a30
lock_acquire+0xcc/0x200
del_timer_sync+0x3c/0xc0
wb_domain_exit+0x14/0x20
mem_cgroup_free+0x14/0x40
mem_cgroup_css_alloc+0x3f9/0x620
cgroup_apply_control_enable+0x190/0x390
cgroup_mkdir+0x290/0x3d0
kernfs_iop_mkdir+0x58/0x80
vfs_mkdir+0x10e/0x1a0
SyS_mkdirat+0xa8/0xd0
SyS_mkdir+0x14/0x20
entry_SYSCALL_64_fastpath+0x18/0xad
Add __mem_cgroup_free() which skips wb_domain_exit(). This is used by
both mem_cgroup_free() and mem_cgroup_alloc() clean up.
Fixes: 0b8f73e104285 ("mm: memcontrol: clean up alloc, online, offline, free functions")
Link: http://lkml.kernel.org/r/20170306192122.24262-1-tahsin@google.com
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following test case triggers BUG() in munlock_vma_pages_range():
int main(int argc, char *argv[])
{
int fd;
system("mount -t tmpfs -o huge=always none /mnt");
fd = open("/mnt/test", O_CREAT | O_RDWR);
ftruncate(fd, 4UL << 20);
mmap(NULL, 4UL << 20, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_FIXED | MAP_LOCKED, fd, 0);
mmap(NULL, 4096, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_LOCKED, fd, 0);
munlockall();
return 0;
}
The second mmap() create PTE-mapping of the first huge page in file. It
makes kernel munlock the page as we never keep PTE-mapped page mlocked.
On munlockall() when we handle vma created by the first mmap(),
munlock_vma_page() returns page_mask == 0, as the page is not mlocked
anymore. On next iteration follow_page_mask() return tail page, but
page_mask is HPAGE_NR_PAGES - 1. It makes us skip to the first tail
page of the next huge page and step on
VM_BUG_ON_PAGE(PageMlocked(page)).
The fix is not use the page_mask from follow_page_mask() at all. It has
no use for us.
Link: http://lkml.kernel.org/r/20170302150252.34120-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org> [4.5+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following test case triggers NULL-pointer derefernce in
try_to_unmap_one():
#include <fcntl.h>
#include <stdlib.h>
#include <unistd.h>
#include <sys/mman.h>
int main(int argc, char *argv[])
{
int fd;
system("mount -t tmpfs -o huge=always none /mnt");
fd = open("/mnt/test", O_CREAT | O_RDWR);
ftruncate(fd, 2UL << 20);
mmap(NULL, 2UL << 20, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_FIXED | MAP_LOCKED, fd, 0);
mmap(NULL, 2UL << 20, PROT_READ | PROT_WRITE,
MAP_SHARED | MAP_LOCKED, fd, 0);
munlockall();
return 0;
}
Apparently, there's a case when we call try_to_unmap() on huge PMDs:
it's TTU_MUNLOCK.
Let's handle this case correctly.
Fixes: c7ab0d2fdc84 ("mm: convert try_to_unmap_one() to use page_vma_mapped_walk()")
Link: http://lkml.kernel.org/r/20170302151159.30592-1-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Obviously, we should not access memblock.memory.regions[right] if
'right' is outside of [0..memblock.memory.cnt>.
Fixes: b92df1de5d28 ("mm: page_alloc: skip over regions of invalid pfns where possible")
Link: http://lkml.kernel.org/r/20170303023745.9104-1-takahiro.akashi@linaro.org
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
userfaultfd_remove() has to be execute before zapping the pagetables or
UFFDIO_COPY could keep filling pages after zap_page_range returned,
which would result in non zero data after a MADV_DONTNEED.
However userfaultfd_remove() may have to release the mmap_sem. This was
handled correctly in MADV_REMOVE, but MADV_DONTNEED accessed a
potentially stale vma (the very vma passed to zap_page_range(vma, ...)).
The fix consists in revalidating the vma in case userfaultfd_remove()
had to release the mmap_sem.
This also optimizes away an unnecessary down_read/up_read in the
MADV_REMOVE case if UFFD_EVENT_FORK had to be delivered.
It all remains zero runtime cost in case CONFIG_USERFAULTFD=n as
userfaultfd_remove() will be defined as "true" at build time.
Link: http://lkml.kernel.org/r/20170302173738.18994-3-aarcange@redhat.com
Signed-off-by: Andrea Arcangeli <aarcange@redhat.com>
Acked-by: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: "Dr. David Alan Gilbert" <dgilbert@redhat.com>
Cc: Mike Kravetz <mike.kravetz@oracle.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The system may panic when initialisation is done when almost all the
memory is assigned to the huge pages using the kernel command line
parameter hugepage=xxxx. Panic may occur like this:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc000000000302b88
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=2048 [ 0.082424] NUMA
pSeries
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.9.0-15-generic #16-Ubuntu
task: c00000021ed01600 task.stack: c00000010d108000
NIP: c000000000302b88 LR: c000000000270e04 CTR: c00000000016cfd0
REGS: c00000010d10b2c0 TRAP: 0300 Not tainted (4.9.0-15-generic)
MSR: 8000000002009033 <SF,VEC,EE,ME,IR,DR,RI,LE>[ 0.082770] CR: 28424422 XER: 00000000
CFAR: c0000000003d28b8 DAR: 0000000000000000 DSISR: 40000000 SOFTE: 1
GPR00: c000000000270e04 c00000010d10b540 c00000000141a300 c00000010fff6300
GPR04: 0000000000000000 00000000026012c0 c00000010d10b630 0000000487ab0000
GPR08: 000000010ee90000 c000000001454fd8 0000000000000000 0000000000000000
GPR12: 0000000000004400 c00000000fb80000 00000000026012c0 00000000026012c0
GPR16: 00000000026012c0 0000000000000000 0000000000000000 0000000000000002
GPR20: 000000000000000c 0000000000000000 0000000000000000 00000000024200c0
GPR24: c0000000016eef48 0000000000000000 c00000010fff7d00 00000000026012c0
GPR28: 0000000000000000 c00000010fff7d00 c00000010fff6300 c00000010d10b6d0
NIP mem_cgroup_soft_limit_reclaim+0xf8/0x4f0
LR do_try_to_free_pages+0x1b4/0x450
Call Trace:
do_try_to_free_pages+0x1b4/0x450
try_to_free_pages+0xf8/0x270
__alloc_pages_nodemask+0x7a8/0xff0
new_slab+0x104/0x8e0
___slab_alloc+0x620/0x700
__slab_alloc+0x34/0x60
kmem_cache_alloc_node_trace+0xdc/0x310
mem_cgroup_init+0x158/0x1c8
do_one_initcall+0x68/0x1d0
kernel_init_freeable+0x278/0x360
kernel_init+0x24/0x170
ret_from_kernel_thread+0x5c/0x74
Instruction dump:
eb81ffe0 eba1ffe8 ebc1fff0 ebe1fff8 4e800020 3d230001 e9499a42 3d220004
3929acd8 794a1f24 7d295214 eac90100 <e9360000> 2fa90000 419eff74 3b200000
---[ end trace 342f5208b00d01b6 ]---
This is a chicken and egg issue where the kernel try to get free memory
when allocating per node data in mem_cgroup_init(), but in that path
mem_cgroup_soft_limit_reclaim() is called which assumes that these data
are allocated.
As mem_cgroup_soft_limit_reclaim() is best effort, it should return when
these data are not yet allocated.
This patch also fixes potential null pointer access in
mem_cgroup_remove_from_trees() and mem_cgroup_update_tree().
Link: http://lkml.kernel.org/r/1487856999-16581-2-git-send-email-ldufour@linux.vnet.ibm.com
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: Vladimir Davydov <vdavydov.dev@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We added support for PUD-sized transparent hugepages, however we count
the event "thp split pud" into thp_split_pmd event.
To separate the event count of thp split pud from pmd, add a new event
named thp_split_pud.
Link: http://lkml.kernel.org/r/1488282380-5076-1-git-send-email-xieyisheng1@huawei.com
Signed-off-by: Yisheng Xie <xieyisheng1@huawei.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Ebru Akagunduz <ebru.akagunduz@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull block fixes from Jens Axboe:
"Sending this a bit sooner than I otherwise would have, as a fix in the
merge window had some unfortunate issues and side effects for some
folks.
This contains:
- Fixes from Jan for the bdi registration/unregistration. These have
been tested by the various parties reporting issues, and should be
solid at this point.
- Also from Jan, fix for axonram gendisk registration.
- A stable fix for zram from Johannes.
- A small series from Ming, fixing up some long standing issues with
blk-mq hardware queue kobject initialization and registration.
- A fix for sed opal from Jon, fixing a nonsensical range check and
some set-but-not-used variables.
- A fix from Neil for a long standing deadlock issue for stacking
device drivers. With this in place, dm/md don't have to work around
the issue anymore, and can be properly fixed up"
* 'for-linus' of git://git.kernel.dk/linux-block:
axonram: Fix gendisk handling
blk: improve order of bio handling in generic_make_request()
Revert "scsi, block: fix duplicate bdi name registration crashes"
block: Make del_gendisk() safer for disks without queues
bdi: Fix use-after-free in wb_congested_put()
block: Allow bdi re-registration
block/sed: Fix opal user range check and unused variables
zram: set physical queue limits to avoid array out of bounds accesses
blk-mq: free hctx->cpumask in release handler of hctx's kobject
blk-mq: make lifetime consistent between hctx and its kobject
blk-mq: make lifetime consitent between q/ctx and its kobject
blk-mq: initialize mq kobjects in blk_mq_init_allocated_queue()
|
|
For full 5-level paging we need a helper to allocate p4d page table.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert all non-architecture-specific code to 5-level paging.
It's mostly mechanical adding handling one more page table level in
places where we deal with pud_t.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 13ad59df67f1 ("mm, page_alloc: avoid page_to_pfn() when merging
buddies") moved the check for memory holes out of page_is_buddy() and
had the callers do the check.
But this wasn't done correctly in one place which caused ia64 to crash
very early in boot.
Update to fix that and make ia64 boot again.
[ v2: Vlastimil pointed out we don't need to call page_to_pfn()
since we already have the result of that in "buddy_pfn" ]
Fixes: 13ad59df67f1 ("avoid page_to_pfn() when merging buddies")
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
bdi_writeback_congested structures get created for each blkcg and bdi
regardless whether bdi is registered or not. When they are created in
unregistered bdi and the request queue (and thus bdi) is then destroyed
while blkg still holds reference to bdi_writeback_congested structure,
this structure will be referencing freed bdi and last wb_congested_put()
will try to remove the structure from already freed bdi.
With commit 165a5e22fafb "block: Move bdi_unregister() to
del_gendisk()", SCSI started to destroy bdis without calling
bdi_unregister() first (previously it was calling bdi_unregister() even
for unregistered bdis) and thus the code detaching
bdi_writeback_congested in cgwb_bdi_destroy() was not triggered and we
started hitting this use-after-free bug. It is enough to boot a KVM
instance with virtio-scsi device to trigger this behavior.
Fix the problem by detaching bdi_writeback_congested structures in
bdi_exit() instead of bdi_unregister(). This is also more logical as
they can get attached to bdi regardless whether it ever got registered
or not.
Fixes: 165a5e22fafb127ecb5914e12e8c32a1f0d3f820
Signed-off-by: Jan Kara <jack@suse.cz>
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
SCSI can call device_add_disk() several times for one request queue when
a device in unbound and bound, creating new gendisk each time. This will
lead to bdi being repeatedly registered and unregistered. This was not a
big problem until commit 165a5e22fafb "block: Move bdi_unregister() to
del_gendisk()" since bdi was only registered repeatedly (bdi_register()
handles repeated calls fine, only we ended up leaking reference to
gendisk due to overwriting bdi->owner) but unregistered only in
blk_cleanup_queue() which didn't get called repeatedly. After
165a5e22fafb we were doing correct bdi_register() - bdi_unregister()
cycles however bdi_unregister() is not prepared for it. So make sure
bdi_unregister() cleans up bdi in such a way that it is prepared for
a possible following bdi_register() call.
An easy way to provoke this behavior is to enable
CONFIG_DEBUG_TEST_DRIVER_REMOVE and use scsi_debug driver to create a
scsi disk which immediately hangs without this fix.
Fixes: 165a5e22fafb127ecb5914e12e8c32a1f0d3f820
Signed-off-by: Jan Kara <jack@suse.cz>
Tested-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
pcpu_get_pages() doesn't use chunk_alloc parameter, remove it.
Fixes: fbbb7f4e149f ("percpu: remove the usage of separate populated bitmap in percpu-vm")
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Update to pcpu_nr_empty_pop_pages in pcpu_alloc() is currently done
without holding pcpu_lock. This can lead to bad updates to the variable.
Add missing lock calls.
Fixes: b539b87fed37 ("percpu: implmeent pcpu_nr_empty_pop_pages and chunk->nr_populated")
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # v3.18+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs 'statx()' update from Al Viro.
This adds the new extended stat() interface that internally subsumes our
previous stat interfaces, and allows user mode to specify in more detail
what kind of information it wants.
It also allows for some explicit synchronization information to be
passed to the filesystem, which can be relevant for network filesystems:
is the cached value ok, or do you need open/close consistency, or what?
From David Howells.
Andreas Dilger points out that the first version of the extended statx
interface was posted June 29, 2010:
https://www.spinics.net/lists/linux-fsdevel/msg33831.html
* 'rebased-statx' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
statx: Add a system call to make enhanced file info available
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched.h split-up from Ingo Molnar:
"The point of these changes is to significantly reduce the
<linux/sched.h> header footprint, to speed up the kernel build and to
have a cleaner header structure.
After these changes the new <linux/sched.h>'s typical preprocessed
size goes down from a previous ~0.68 MB (~22K lines) to ~0.45 MB (~15K
lines), which is around 40% faster to build on typical configs.
Not much changed from the last version (-v2) posted three weeks ago: I
eliminated quirks, backmerged fixes plus I rebased it to an upstream
SHA1 from yesterday that includes most changes queued up in -next plus
all sched.h changes that were pending from Andrew.
I've re-tested the series both on x86 and on cross-arch defconfigs,
and did a bisectability test at a number of random points.
I tried to test as many build configurations as possible, but some
build breakage is probably still left - but it should be mostly
limited to architectures that have no cross-compiler binaries
available on kernel.org, and non-default configurations"
* 'WIP.sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (146 commits)
sched/headers: Clean up <linux/sched.h>
sched/headers: Remove #ifdefs from <linux/sched.h>
sched/headers: Remove the <linux/topology.h> include from <linux/sched.h>
sched/headers, hrtimer: Remove the <linux/wait.h> include from <linux/hrtimer.h>
sched/headers, x86/apic: Remove the <linux/pm.h> header inclusion from <asm/apic.h>
sched/headers, timers: Remove the <linux/sysctl.h> include from <linux/timer.h>
sched/headers: Remove <linux/magic.h> from <linux/sched/task_stack.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/init.h>
sched/core: Remove unused prefetch_stack()
sched/headers: Remove <linux/rculist.h> from <linux/sched.h>
sched/headers: Remove the 'init_pid_ns' prototype from <linux/sched.h>
sched/headers: Remove <linux/signal.h> from <linux/sched.h>
sched/headers: Remove <linux/rwsem.h> from <linux/sched.h>
sched/headers: Remove the runqueue_is_locked() prototype
sched/headers: Remove <linux/sched.h> from <linux/sched/hotplug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/debug.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/nohz.h>
sched/headers: Remove <linux/sched.h> from <linux/sched/stat.h>
sched/headers: Remove the <linux/gfp.h> include from <linux/sched.h>
sched/headers: Remove <linux/rtmutex.h> from <linux/sched.h>
...
|
