Age | Commit message (Collapse) | Author |
|
To allow filtering of huge pages, makedumpfile must be able to identify
them in the dump. This can be done by checking the appropriate page
flag, so communicate its value to makedumpfile through the VMCOREINFO
interface.
There's only one small catch. Depending on how many page flags are
available on a given architecture, this bit can be called PG_head or
PG_compound.
I sent a similar patch back in 2012, but Eric Biederman did not like
using an #ifdef. So, this time I'm adding a common symbol
(PG_head_mask) instead.
See https://lkml.org/lkml/2012/11/28/91 for the previous version.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Shaohua Li <shli@kernel.org>
Cc: Alexey Kardashevskiy <aik@ozlabs.ru>
Cc: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
+ some pr_warning -> pr_warn and checkpatch warning fixes
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If we try to perform a kexec when the machine is in ST (Single-Threaded) mode
(ppc64_cpu --smt=off), the kexec operation doesn't succeed properly, and we
get the following messages during boot:
[ 0.089866] POWER8 performance monitor hardware support registered
[ 0.089985] power8-pmu: PMAO restore workaround active.
[ 5.095419] Processor 1 is stuck.
[ 10.097933] Processor 2 is stuck.
[ 15.100480] Processor 3 is stuck.
[ 20.102982] Processor 4 is stuck.
[ 25.105489] Processor 5 is stuck.
[ 30.108005] Processor 6 is stuck.
[ 35.110518] Processor 7 is stuck.
[ 40.113369] Processor 9 is stuck.
[ 45.115879] Processor 10 is stuck.
[ 50.118389] Processor 11 is stuck.
[ 55.120904] Processor 12 is stuck.
[ 60.123425] Processor 13 is stuck.
[ 65.125970] Processor 14 is stuck.
[ 70.128495] Processor 15 is stuck.
[ 75.131316] Processor 17 is stuck.
Note that only the sibling threads are stuck, while the primary threads (0, 8,
16 etc) boot just fine. Looking closer at the previous step of kexec, we observe
that kexec tries to wakeup (bring online) the sibling threads of all the cores,
before performing kexec:
[ 9464.131231] Starting new kernel
[ 9464.148507] kexec: Waking offline cpu 1.
[ 9464.148552] kexec: Waking offline cpu 2.
[ 9464.148600] kexec: Waking offline cpu 3.
[ 9464.148636] kexec: Waking offline cpu 4.
[ 9464.148671] kexec: Waking offline cpu 5.
[ 9464.148708] kexec: Waking offline cpu 6.
[ 9464.148743] kexec: Waking offline cpu 7.
[ 9464.148779] kexec: Waking offline cpu 9.
[ 9464.148815] kexec: Waking offline cpu 10.
[ 9464.148851] kexec: Waking offline cpu 11.
[ 9464.148887] kexec: Waking offline cpu 12.
[ 9464.148922] kexec: Waking offline cpu 13.
[ 9464.148958] kexec: Waking offline cpu 14.
[ 9464.148994] kexec: Waking offline cpu 15.
[ 9464.149030] kexec: Waking offline cpu 17.
Instrumenting this piece of code revealed that the cpu_up() operation actually
fails with -EBUSY. Thus, only the primary threads of all the cores are online
during kexec, and hence this is a sure-shot receipe for disaster, as explained
in commit e8e5c2155b (powerpc/kexec: Fix orphaned offline CPUs across kexec),
as well as in the comment above wake_offline_cpus().
It turns out that cpu_up() was returning -EBUSY because the variable
'cpu_hotplug_disabled' was set to 1; and this disabling of CPU hotplug was done
by migrate_to_reboot_cpu() inside kernel_kexec().
Now, migrate_to_reboot_cpu() was originally written with the assumption that
any further code will not need to perform CPU hotplug, since we are anyway in
the reboot path. However, kexec is clearly not such a case, since we depend on
onlining CPUs, atleast on powerpc.
So re-enable cpu-hotplug after returning from migrate_to_reboot_cpu() in the
kexec path, to fix this regression in kexec on powerpc.
Also, wrap the cpu_up() in powerpc kexec code within a WARN_ON(), so that we
can catch such issues more easily in the future.
Fixes: c97102ba963 (kexec: migrate to reboot cpu)
Cc: stable@vger.kernel.org
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
To increase compiler portability there is <linux/compiler.h> which
provides convenience macros for various gcc constructs. Eg: __weak for
__attribute__((weak)). I've replaced all instances of gcc attributes
with the right macro in the kernel subsystem.
Signed-off-by: Gideon Israel Dsouza <gidisrael@gmail.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Code that is obj-y (always built-in) or dependent on a bool Kconfig
(built-in or absent) can never be modular. So using module_init as an
alias for __initcall can be somewhat misleading.
Fix these up now, so that we can relocate module_init from init.h into
module.h in the future. If we don't do this, we'd have to add module.h
to obviously non-modular code, and that would be a worse thing.
The audit targets the following module_init users for change:
kernel/user.c obj-y
kernel/kexec.c bool KEXEC (one instance per arch)
kernel/profile.c bool PROFILING
kernel/hung_task.c bool DETECT_HUNG_TASK
kernel/sched/stats.c bool SCHEDSTATS
kernel/user_namespace.c bool USER_NS
Note that direct use of __initcall is discouraged, vs. one of the
priority categorized subgroups. As __initcall gets mapped onto
device_initcall, our use of subsys_initcall (which makes sense for these
files) will thus change this registration from level 6-device to level
4-subsys (i.e. slightly earlier). However no observable impact of that
difference has been observed during testing.
Also, two instances of missing ";" at EOL are fixed in kexec.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In order to allow the COMPAT_SYSCALL_DEFINE macro generate code that
performs proper zero and sign extension convert all 64 bit parameters
to their corresponding 32 bit compat counterparts.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
|
|
vmcoreinfo_append_str()
vsnprintf() may let 'r' larger than sizeof(buf), in this case, if 'r' is
also less than "vmcoreinfo_max_size - vmcoreinfo_size" (left size of
destination buffer), next memcpy() will read the unexpected addresses.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
For general-purpose (i.e. distro) kernel builds it makes sense to build
with CONFIG_KEXEC to allow end users to choose what kind of things they
want to do with kexec. However, in the face of trying to lock down a
system with such a kernel, there needs to be a way to disable kexec_load
(much like module loading can be disabled). Without this, it is too easy
for the root user to modify kernel memory even when CONFIG_STRICT_DEVMEM
and modules_disabled are set. With this change, it is still possible to
load an image for use later, then disable kexec_load so the image (or lack
of image) can't be altered.
The intention is for using this in environments where "perfect"
enforcement is hard. Without a verified boot, along with verified
modules, and along with verified kexec, this is trying to give a system a
better chance to defend itself (or at least grow the window of
discoverability) against attack in the face of a privilege escalation.
In my mind, I consider several boot scenarios:
1) Verified boot of read-only verified root fs loading fd-based
verification of kexec images.
2) Secure boot of writable root fs loading signed kexec images.
3) Regular boot loading kexec (e.g. kcrash) image early and locking it.
4) Regular boot with no control of kexec image at all.
1 and 2 don't exist yet, but will soon once the verified kexec series has
landed. 4 is the state of things now. The gap between 2 and 4 is too
large, so this change creates scenario 3, a middle-ground above 4 when 2
and 1 are not possible for a system.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 1b3a5d02ee07 ("reboot: move arch/x86 reboot= handling to generic
kernel") moved reboot= handling to generic code. In the process it also
removed the code in native_machine_shutdown() which are moving reboot
process to reboot_cpu/cpu0.
I guess that thought must have been that all reboot paths are calling
migrate_to_reboot_cpu(), so we don't need this special handling. But
kexec reboot path (kernel_kexec()) is not calling
migrate_to_reboot_cpu() so above change broke kexec. Now reboot can
happen on non-boot cpu and when INIT is sent in second kerneo to bring
up BP, it brings down the machine.
So start calling migrate_to_reboot_cpu() in kexec reboot path to avoid
this problem.
Bisected by WANG Chao.
Reported-by: Matthew Whitehead <mwhitehe@redhat.com>
Reported-by: Dave Young <dyoung@redhat.com>
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Tested-by: Baoquan He <bhe@redhat.com>
Tested-by: WANG Chao <chaowang@redhat.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a flag to tell the PCI subsystem that kernel is shutting down in
preparation to kexec a kernel. Add code in PCI subsystem to use this flag
to clear Bus Master bit on PCI devices only in case of kexec reboot.
This fixes a power-off problem on Acer Aspire V5-573G and likely other
machines and avoids any other issues caused by clearing Bus Master bit on
PCI devices in normal shutdown path. The problem was introduced by
b566a22c2332 ("PCI: disable Bus Master on PCI device shutdown").
This patch is based on discussion at
http://marc.info/?l=linux-pci&m=138425645204355&w=2
Link: https://bugzilla.kernel.org/show_bug.cgi?id=63861
Reported-by: Chang Liu <cl91tp@gmail.com>
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: stable@vger.kernel.org # v3.5+
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
|
|
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Code can not run here forever, so remove the unnecessary return.
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Suggested-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Simplify the logic of variable assignments.
[akpm@linux-foundation.org: replace min_t with min, remove unneeded casts]
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The types of the following local variables:
- ubytes/mbytes in kimage_load_crash_segment()/kimage_load_normal_segment()
- r in vmcoreinfo_append_str()
are wrong, so fix them.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now, vmap_area_list is exported as VMCOREINFO for makedumpfile to get
the start address of vmalloc region (vmalloc_start). The address which
contains vmalloc_start value is represented as below:
vmap_area_list.next - OFFSET(vmap_area.list) + OFFSET(vmap_area.va_start)
However, both OFFSET(vmap_area.va_start) and OFFSET(vmap_area.list)
aren't exported as VMCOREINFO.
So this patch exports them externally with small cleanup.
[akpm@linux-foundation.org: vmalloc.h should include list.h for list_head]
Signed-off-by: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Dave Anderson <anderson@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Although our intention is to unexport internal structure entirely, but
there is one exception for kexec. kexec dumps address of vmlist and
makedumpfile uses this information.
We are about to remove vmlist, then another way to retrieve information
of vmalloc layer is needed for makedumpfile. For this purpose, we
export vmap_area_list, instead of vmlist.
Signed-off-by: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Anderson <anderson@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use common help functions to free reserved pages.
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Reviewed-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We can extend kexec-tools to support multiple "Crash kernel" in /proc/iomem
instead.
So we can use "Crash kernel" instead of "Crash kernel low" in /proc/iomem.
Suggested-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1366089828-19692-3-git-send-email-yinghai@kernel.org
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Per hpa, use crashkernel=X,high crashkernel=Y,low instead of
crashkernel_hign=X crashkernel_low=Y. As that could be extensible.
-v2: according to Vivek, change delimiter to ;
-v3: let hign and low only handle simple form and it conforms to
description in kernel-parameters.txt
still keep crashkernel=X override any crashkernel=X,high
crashkernel=Y,low
-v4: update get_last_crashkernel returning and add more strict
checking in parse_crashkernel_simple() found by HATAYAMA.
-v5: Change delimiter back to , according to HPA.
also separate parse_suffix from parse_simper according to vivek.
so we can avoid @pos in that path.
-v6: Tight the checking about crashkernel=X,highblahblah,high
found by HTYAYAMA.
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1366089828-19692-5-git-send-email-yinghai@kernel.org
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Vivek found old kexec-tools does not work new kernel anymore.
So change back crashkernel= back to old behavoir, and add crashkernel_high=
to let user decide if buffer could be above 4G, and also new kexec-tools will
be needed.
-v2: let crashkernel=X override crashkernel_high=
update description about _high will be ignored by crashkernel=X
-v3: update description about kernel-parameters.txt according to Vivek.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1366089828-19692-4-git-send-email-yinghai@kernel.org
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
Though there is no error if we free a NULL pointer, I think we could
avoid this behaviour. Change the code a little in kimage_crash_alloc()
could avoid this kind of unnecessary free.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If kimage_normal_alloc() fails to alloc pages for image->swap_page, it
should call kimage_free_page_list() to free allocated pages in
image->control_pages list before it frees image.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
If kimage_normal_alloc() fails to initialize an allocated kimage, it will
free the image but would still set 'rimage', as a result kexec_load will
try to free it again.
This would explode as part of the freeing process is accessing internal
members which point to uninitialized memory.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch exports a PG_hwpoison into vmcoreinfo when
CONFIG_MEMORY_FAILURE is defined. "makedumpfile" needs to read
information of memory, such as 'mem_section', 'zone', 'pageflags' from
vmcore.
We introduce a function into "makedumpfile" to exclude hwpoison page from
vmcore dump. In order to introduce this function, PG_hwpoison flag have
to export into vmcoreinfo.
Signed-off-by: Mitsuhiro Tanino <mitsuhiro.tanino.gm@hitachi.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Mitsuhiro Tanino <mitsuhiro.tanino.gm@hitachi.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
hole_end has been checked to make sure it is <= crash_res.end in the while
condition check, so the if condition check is duplicate.
Signed-off-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Reviewed-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
tAdd adds the values related to buddy system to vmcoreinfo data so that
makedumpfile (dump filtering command) can filter out all free pages with
the new logic.
It's faster than the current logic because it can distinguish free page
by analyzing page structure at the same time as filtering for other
unnecessary pages (e.g. anonymous page).
OTOH, the current logic has to trace free_list to distinguish free pages
while analyzing page structure to filter out other unnecessary pages.
The new logic uses the fact that buddy page is marked by _mapcount ==
PAGE_BUDDY_MAPCOUNT_VALUE. But, _mapcount shares its memory with other
fields for SLAB/SLUB when PG_slab is set, so we need to check if PG_slab
is set or not before looking up _mapcount value. And we can get the
order of buddy system from private field. To sum it up, the values
below are required for this logic.
Required values:
- OFFSET(page._mapcount)
- OFFSET(page.private)
- NUMBER(PG_slab)
- NUMBER(PAGE_BUDDY_MAPCOUNT_VALUE)
Changelog from v1 to v2:
1. remove SIZE(pageflags)
The new logic was changed after I sent v1 patch.
Accordingly, SIZE(pageflags) has been unnecessary for makedumpfile.
What's makedumpfile:
makedumpfile creates a small dumpfile by excluding unnecessary pages
for the analysis. To distinguish unnecessary pages, makedumpfile gets
the vmcoreinfo data which has the minimum debugging information only
for dump filtering.
Signed-off-by: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
During kdump kernel's booting stage, it need to find low ram for
swiotlb buffer when system does not support intel iommu/dmar remapping.
kexed-tools is appending memmap=exactmap and range from /proc/iomem
with "Crash kernel", and that range is above 4G for 64bit after boot
protocol 2.12.
We need to add another range in /proc/iomem like "Crash kernel low",
so kexec-tools could find that info and append to kdump kernel
command line.
Try to reserve some under 4G if the normal "Crash kernel" is above 4G.
User could specify the size with crashkernel_low=XX[KMG].
-v2: fix warning that is found by Fengguang's test robot.
-v3: move out get_mem_size change to another patch, to solve compiling
warning that is found by Borislav Petkov <bp@alien8.de>
-v4: user must specify crashkernel_low if system does not support
intel or amd iommu.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1359058816-7615-31-git-send-email-yinghai@kernel.org
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Rob Landley <rob@landley.net>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
The inclusion of <generated/utsrelease.h> is unnecessary.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The last line of vmcoreinfo note does not end with \n. Parsing all the
lines in note becomes easier if all lines end with \n instead of trying to
special case the last line.
I know at least one tool, vmcore-dmesg in kexec-tools tree which made the
assumption that all lines end with \n. I think it is a good idea to fix
it.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Atsushi Kumagai <kumagai-atsushi@mxc.nes.nec.co.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge third batch of patches from Andrew Morton:
- Some MM stragglers
- core SMP library cleanups (on_each_cpu_mask)
- Some IPI optimisations
- kexec
- kdump
- IPMI
- the radix-tree iterator work
- various other misc bits.
"That'll do for -rc1. I still have ~10 patches for 3.4, will send
those along when they've baked a little more."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
backlight: fix typo in tosa_lcd.c
crc32: add help text for the algorithm select option
mm: move hugepage test examples to tools/testing/selftests/vm
mm: move slabinfo.c to tools/vm
mm: move page-types.c from Documentation to tools/vm
selftests/Makefile: make `run_tests' depend on `all'
selftests: launch individual selftests from the main Makefile
radix-tree: use iterators in find_get_pages* functions
radix-tree: rewrite gang lookup using iterator
radix-tree: introduce bit-optimized iterator
fs/proc/namespaces.c: prevent crash when ns_entries[] is empty
nbd: rename the nbd_device variable from lo to nbd
pidns: add reboot_pid_ns() to handle the reboot syscall
sysctl: use bitmap library functions
ipmi: use locks on watchdog timeout set on reboot
ipmi: simplify locking
ipmi: fix message handling during panics
ipmi: use a tasklet for handling received messages
ipmi: increase KCS timeouts
ipmi: decrease the IPMI message transaction time in interrupt mode
...
|
|
When using crashkernel=2M-256M, the kernel doesn't give any warning. This
is misleading sometimes.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@oracle.com>
Acked-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
nommu platforms don't have very interesting swapper_pg_dir pointers and
usually just #define them to NULL, meaning that we can't include them in
the vmcoreinfo on the kexec crash path.
This patch only saves the swapper_pg_dir if we have an MMU.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove all #inclusions of asm/system.h preparatory to splitting and killing
it. Performed with the following command:
perl -p -i -e 's!^#\s*include\s*<asm/system[.]h>.*\n!!' `grep -Irl '^#\s*include\s*<asm/system[.]h>' *`
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
The current device suspend/resume phases during system-wide power
transitions appear to be insufficient for some platforms that want
to use the same callback routines for saving device states and
related operations during runtime suspend/resume as well as during
system suspend/resume. In principle, they could point their
.suspend_noirq() and .resume_noirq() to the same callback routines
as their .runtime_suspend() and .runtime_resume(), respectively,
but at least some of them require device interrupts to be enabled
while the code in those routines is running.
It also makes sense to have device suspend-resume callbacks that will
be executed with runtime PM disabled and with device interrupts
enabled in case someone needs to run some special code in that
context during system-wide power transitions.
Apart from this, .suspend_noirq() and .resume_noirq() were introduced
as a workaround for drivers using shared interrupts and failing to
prevent their interrupt handlers from accessing suspended hardware.
It appears to be better not to use them for other porposes, or we may
have to deal with some serious confusion (which seems to be happening
already).
For the above reasons, introduce new device suspend/resume phases,
"late suspend" and "early resume" (and analogously for hibernation)
whose callback will be executed with runtime PM disabled and with
device interrupts enabled and whose callback pointers generally may
point to runtime suspend/resume routines.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
|
|
Currently it is possible to set the crash_size via the sysfs
/sys/kernel/kexec_crash_size even if no crash kernel memory has been
defined with the "crashkernel" parameter. In this case "crashk_res" is
not initialized and crashk_res.start = crashk_res.end = 0. Unfortunately
resource_size(&crashk_res) returns 1 in this case. This breaks the s390
implementation of crash_(un)map_reserved_pages().
To fix the problem the correct "old_size" is now calculated in
crash_shrink_memory(). "old_size is set to "0" if crashk_res is not
initialized. With this change crash_shrink_memory() will do nothing, when
"crashk_res" is not initialized. It will return "0" for "echo 0 >
/sys/kernel/kexec_crash_size" and -EINVAL for "echo [not zero] >
/sys/kernel/kexec_crash_size".
In addition to that this patch also simplifies the "ret = -EINVAL" vs.
"ret = 0" logic as suggested by Simon Horman.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Reviewed-by: Dave Young <dyoung@redhat.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When shrinking crashkernel memory using /sys/kernel/kexec_crash_size for
the newly added memory no RAM resource is created at the moment.
Example:
$ cat /proc/iomem
00000000-bfffffff : System RAM
00000000-005b7ac3 : Kernel code
005b7ac4-009743bf : Kernel data
009bb000-00a85c33 : Kernel bss
c0000000-cfffffff : Crash kernel
d0000000-ffffffff : System RAM
$ echo 0 > /sys/kernel/kexec_crash_size
$ cat /proc/iomem
00000000-bfffffff : System RAM
00000000-005b7ac3 : Kernel code
005b7ac4-009743bf : Kernel data
009bb000-00a85c33 : Kernel bss
<<-- here is System RAM missing
d0000000-ffffffff : System RAM
One result of this bug is that the memory chunk can never be set offline
using memory hotplug. With this patch I insert a new "System RAM"
resource for the released memory. Then the upper example looks like the
following:
$ echo 0 > /sys/kernel/kexec_crash_size
$ cat /proc/iomem
00000000-bfffffff : System RAM
00000000-005b7ac3 : Kernel code
005b7ac4-009743bf : Kernel data
009bb000-00a85c33 : Kernel bss
c0000000-cfffffff : System RAM <<-- new rescoure
d0000000-ffffffff : System RAM
And now I can set chunk c0000000-cfffffff offline.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
KMSG_DUMP_KEXEC is useless because we already save kernel messages inside
/proc/vmcore, and it is unsafe to allow modules to do other stuffs in a
crash dump scenario.
[akpm@linux-foundation.org: fix powerpc build]
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Jarod Wilson <jarod@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Using [un]lock_system_sleep() is safer than directly using mutex_[un]lock()
on 'pm_mutex', since the latter could lead to freezing failures. Hence convert
all the present users of mutex_[un]lock(&pm_mutex) to use these safe APIs
instead.
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Reviewed-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
This patch introduces a mechanism that allows architecture backends to
remove page tables for the crashkernel memory. This can protect the loaded
kdump kernel from being overwritten by broken kernel code. Two new
functions crash_map_reserved_pages() and crash_unmap_reserved_pages() are
added that can be implemented by architecture code. The
crash_map_reserved_pages() function is called before and
crash_unmap_reserved_pages() after the crashkernel segments are loaded. The
functions are also called in crash_shrink_memory() to create/remove page
tables when the crashkernel memory size is reduced.
To support architectures that have large pages this patch also introduces
a new define KEXEC_CRASH_MEM_ALIGN. The crashkernel start and size must
always be aligned with KEXEC_CRASH_MEM_ALIGN.
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Currently the vmcoreinfo note is only initialized in case of kdump. On s390
it is possible to create kernel dumps with other dump mechanisms than kdump
(e.g. via hypervisor dump or stand-alone dump tools). For those dumps it
would also be desirable to include the vmcoreinfo data. To accomplish this,
with this patch the vmcoreinfo ELF note is always initialized, not only in
case of a (kdump) crash. On s390 we will add an ABI defined pointer at
a well known address to vmcoreinfo so that dump analysis tools are able to
find this information.
In particular on s390 we have a tool named zgetdump. With this tool it is
possible to convert dump formats on the fly using fuse. E.g. you can mount a
s390 stand-alone dump as ELF dump. When this is done, the tool finds the
vmcoreinfo in the stand-alone dump via the well known ABI defined address and
it creates the respective VMCOREINFO ELF note in the output ELF dump. This then
can be used e.g. by makedumpfile for dump filtering. No more need for a
vmlinux file with debug information.
So this will look like the following:
$ zgetdump --mount standalone.dump -f elf /mnt
$ ls /mnt
dump.elf
$ readelf -n /mnt/dump.elf
$ ...
VMCOREINFO 0x00000474 Unknown note type: (0x00000000)
$ makedumpfile -c -d 31 /mnt/dump.elf dump.kdump
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
On s390 there is a different KEXEC_CONTROL_MEMORY_LIMIT for the normal and
the kdump kexec case. Therefore this patch introduces a new macro
KEXEC_CRASH_CONTROL_MEMORY_LIMIT. This is set to
KEXEC_CONTROL_MEMORY_LIMIT for all architectures that do not define
KEXEC_CRASH_CONTROL_MEMORY_LIMIT.
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Since suspend, resume and shutdown operations in struct sysdev_class
and struct sysdev_driver are not used any more, remove them. Also
drop sysdev_suspend(), sysdev_resume() and sysdev_shutdown() used
for executing those operations and modify all of their users
accordingly. This reduces kernel code size quite a bit and reduces
its complexity.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Device suspend/resume infrastructure is used not only by the suspend
and hibernate code in kernel/power, but also by APM, Xen and the
kexec jump feature. However, commit 40dc166cb5dddbd36aa4ad11c03915ea
(PM / Core: Introduce struct syscore_ops for core subsystems PM)
failed to add syscore_suspend() and syscore_resume() calls to that
code, which generally leads to breakage when the features in question
are used.
To fix this problem, add the missing syscore_suspend() and
syscore_resume() calls to arch/x86/kernel/apm_32.c, kernel/kexec.c
and drivers/xen/manage.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
|
|
* 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6:
Fix common misspellings
|
|
On ppc64 the crashkernel region almost always overlaps an area of firmware.
This works fine except when using the sysfs interface to reduce the kdump
region. If we free the firmware area we are guaranteed to crash.
Rename free_reserved_phys_range to crash_free_reserved_phys_range and make
it a weak function so we can override it.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
|
|
Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
|
|
"gadget", "through", "command", "maintain", "maintain", "controller", "address",
"between", "initiali[zs]e", "instead", "function", "select", "already",
"equal", "access", "management", "hierarchy", "registration", "interest",
"relative", "memory", "offset", "already",
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
After all that's what they are intended for.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|