| Age | Commit message (Collapse) | Author |
|---|
|
QCN9274 can support single-PHY or split-PHY architecture. Currently,
only the single-PHY architecture is supported in ath12k.
The split-PHY QCN9274 requires different AMSS firmware binary
"amss_dualmac.bin".
Hence, add support to read board id from OTP. Based on board id
decide whether single-mac / dual-mac firmware needs to be downloaded
to the target. Also, update HW param max_radios to support split-PHY
in QCN9274.
Also, add new Firmware IE for firmware_N.bin
"ATH11K_FW_IE_AMSS_DUALMAC_IMAGE" to support dualmac QCN9274.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Ganesh Babu Jothiram <quic_gjothira@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-13-quic_rajkbhag@quicinc.com
|
|
Currently, PCI read is failing for the registers belonging to
SECURITY_CONTROL_WLAN registers. These registers read is required
to read the board-id to identify the dual-mac QCN9274 hardware.
The failure is because, for these registers (SECURITY_CONTROL_WLAN)
offset, ath12k_pci_get_window_start() returns window_start as 0. Due
to this PCI read is done without PCI select window and with
window_start offset as 0.
Hence, fix PCI read and write by doing PCI select window and by using
the correct window_start offset - WINDOW_START for
SECURITY_CONTROL_WLAN registers.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-12-quic_rajkbhag@quicinc.com
|
|
When more than one pdev is supported in the chip/SoC, the packet
belonging to second pdev is given to first pdev due to not identifying
the MAC id in the WBM error path. So ping fails.
In WBM error path, src link id information not available in the
descriptor. So get this information from the msdu_end 64bit tag. It
is necessary to get the src link id to identify the MAC id in the
given chip. Then only we can pass the skb to the corresponding pdev.
The msdu_end 64bit tag is available only if compact Rx TLVs
descriptors are used. Thus, src link id is fetched correctly in WBM
error path when compact descriptors are in use.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-11-quic_rajkbhag@quicinc.com
|
|
Most of the RX descriptors fields are currently not used in the
ath12k driver. Hence add support to selectively subscribe to the
required quad words (64 bits) within msdu_end and mpdu_start of
rx_desc.
Add compact rx_desc structures and configure the bit mask for Rx TLVs
(msdu_end, mpdu_start, mpdu_end) via registers. With these registers
SW can configure to DMA the partial TLV struct to Rx buffer.
Each TLV type has its own register to configure the mask value.
The mask value configured in register will indicate if a particular
QWORD has to be written to rx buffer or not i.e., if Nth bit is enabled
in the mask Nth QWORD will be written and it will not be written if the
bit is disabled in mask. While 0th bit indicates whether TLV tag will be
written or not.
Advantages of Qword subscription of TLVs
- Avoid multiple cache-line misses as the all the required fields
of the TLV are within 128 bytes.
- Memory optimization as TLVs + DATA + SHINFO can fit in 2k buffer
even for 64 bit kernel.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-10-quic_rajkbhag@quicinc.com
|
|
With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.
The hardware param hal_desc_sz value cannot be constant for the same
hardware. It depends on the size of rx_desc structure which may
change based on firmware capability to support word mask subscription.
Hence, remove hal_desc_sz from hardware param and add hal_rx_ops
to get the size of rx_desc in run time.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-9-quic_rajkbhag@quicinc.com
|
|
With word mask subscription support, the rx_desc structure will
change. The fields in this structure rx_desc will be reduced to only
the required fields. To make word mask subscription changes compatible
with the older firmware version (firmware that does not support word
mask subscription), two different structures of rx_desc will be
required for the same hardware.
Most of the hal_ops are directly related to rx_desc.
Hence, split hal_ops into operations that are independent of rx_desc
(hal_ops) and the operations that are directly dependent on rx_desc
(hal_rx_ops). These hal_rx_ops depend on both hardware and firmware
hence move them out of hw_params.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-8-quic_rajkbhag@quicinc.com
|
|
In segment memory mode, firmware allocates memory segments of size
2 MB. This 2 MB memory is used by firmware for the number of peers.
This number of peer is sent from host to firmware during WMI init
command. For single-phy the number of peers sent is
TARGET_NUM_PEERS_SINGLE = 529 (512 + 17). While for split-phy number
of peers sent to firmware is TARGET_NUM_PEERS_DBS = 2 *(512 + 17) =
1058. With this 1058 number of peers firmware is unable to allocate
memory in 2 MB segment and firmware crash is observed.
Hence, fix this firmware crash by reducing the number of stations
TARGET_NUM_STATIONS for split-phy.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-7-quic_rajkbhag@quicinc.com
|
|
Currently only one MHI device is registered successfully on platform
having two or more identical MHI devices. This is beacuse QMI service
runs with identical QRTR node ID. And, qrtr-lookup cannot register
more than one QMI service with identical node ID.
Hence, generate a unique QRTR instance ID from PCIe domain number and
bus number. QMI allows node id to be written on scratch register.
Add logic to write QRTR node id to the register. It is available for
firmware to uniquely identify an instance.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-6-quic_rajkbhag@quicinc.com
|
|
In QCN9274, RX packet's multicast and broadcast(MCBC) flag is fetched
from RX descriptor's msdu_end info5 member but it is not correct
for QCN9274. Due to this with encryption, ARP request packet is wrongly
marked as MCBC packet and it is sent to mac80211 without setting
RX_FLAG_PN_VALIDATED & RX_FLAG_DECRYPTED flag. This results in packet
getting dropped in mac80211. Hence ping initiated from station to AP
fails.
Fix this by fetching correct MCBC flag in case of QCN9274.
For QC9274 MCBC flag should be fetched from RX descriptor's mpdu_start
info6 member.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Fixes: 8f04852e90cb ("wifi: ath12k: Use msdu_end to check MCBC")
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-5-quic_rajkbhag@quicinc.com
|
|
Add support to process WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT
service bit. If this service bit is set by firmware, then it expects
host to set rx_peer_meta_data_ver in wmi_resource_config's flags2
with value 3 for QCN9274 to indicate as V1B meta version. If this is
not set firmware crash is seen during peer addition.
Hence, if WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT service bit
is set by firmware, set correct peer metadata version to avoid
firmware crash.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-4-quic_rajkbhag@quicinc.com
|
|
Currently while fetching for pdev id from WMI_SERVICE_READY_EXT_EVENTID
we consider 32 bit pdev_id in ath12k_wmi_caps_ext_params structure. But
Firmware sends lower 16 bit for pdev id along with higher 16 bit for
hw_link_id. Due to this wrong pdev id is fetched. This wrong pdev id
when used for WMI commands leads to Firmware crash.
Hence fetch the correct pdev id considering only the lower 16 bits.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-3-quic_rajkbhag@quicinc.com
|
|
When any VDEV is started, MBSSID flags are passed to firmware to
indicate if its a MBSSID/EMA AP vdev. If the interface is not an AP
or if the AP doesn't support MBSSID, the vdev needs to be brought up
as a non MBSSID vdev. Set these flags as a non MBSSID AP by default
which can be updated as and when MBSSID support is added in ath12k.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-2-quic_rajkbhag@quicinc.com
|
|
Firmware IE containers can dynamically provide various information
what firmware supports. Also it can embed more than one image so
updating firmware is easy, user just needs to update one file in
/lib/firmware/.
The firmware API 2 or higher will use the IE container format, the
current API 1 will not use the new format but it still is supported
for some time. Firmware API 2 files are named as firmware-2.bin
(which contains both amss.bin and m3.bin images) and API 1 files are
amss.bin and m3.bin.
Currently ath12k PCI driver provides firmware binary (amss.bin) path to
MHI driver, MHI driver reads firmware from filesystem and boots it. Add
provision to read firmware files from ath12k driver and provide the amss.bin
firmware data and size to MHI using a pointer.
Currently enum ath12k_fw_features is empty, the patches adding features will
add the flags.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123122812.3811251-1-quic_rajkbhag@quicinc.com
|
|
WMI_PEER_ASSOC_CMDID
Currently when connecting to an AP with 11AX-HE phy mode, host sends
WMI_VDEV_PARAM_SET_HEMU_MODE parameter to firmware after
WMI_PEER_ASSOC_CMDID command. This results in TXBF not working, because
firmware calculates TXBF values while handling WMI_PEER_ASSOC_CMDID,
however at that time WMI_VDEV_PARAM_SET_HEMU_MODE has not been sent yet.
See below log:
AP sends "VHT/HE/EHT NDP Announcement" to station, and station sends
"Action no Ack" of category code HE to AP, the "Nc Index" and
"Codebook Information" are wrong:
Issued action:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 152
HE MIMO Control: 0x0004008018
.... .... .... .... .... .... .... .... .... .000 = Nc Index: 1 Column (0)
.... .... .... .... .... .... .... ..0. .... .... = Codebook Information: 0
Change to send WMI_VDEV_PARAM_SET_HEMU_MODE before WMI_PEER_ASSOC_CMDID,
then firmware will calculate the TXBF values with valid parameters
instead of empty values. TXBF works well and throughput performance is
improved from 80 Mbps to 130 Mbps with this patch.
Good action after this patch:
IEEE 802.11 Action No Ack, Flags: ........
IEEE 802.11 wireless LAN
Fixed parameters
Category code: HE (30)
HE Action: HE Compressed Beamforming And CQI (0)
Total length: 409
HE MIMO Control: 0x0004008219
.... .... .... .... .... .... .... .... .... .001 = Nc Index: 2 Columns (1)
.... .... .... .... .... .... .... ..1. .... .... = Codebook Information: 1
This change applies to all chipsets.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: 38dfe775d0ab ("wifi: ath11k: push MU-MIMO params from hostapd to hardware")
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240131021832.17298-1-quic_bqiang@quicinc.com
|
|
The ath9k_wmi_event_tasklet() used in ath9k_htc assumes that all the data
structures have been fully initialised by the time it runs. However, because of
the order in which things are initialised, this is not guaranteed to be the
case, because the device is exposed to the USB subsystem before the ath9k driver
initialisation is completed.
We already committed a partial fix for this in commit:
8b3046abc99e ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
However, that commit only aborted the WMI_TXSTATUS_EVENTID command in the event
tasklet, pairing it with an "initialisation complete" bit in the TX struct. It
seems syzbot managed to trigger the race for one of the other commands as well,
so let's just move the existing synchronisation bit to cover the whole
tasklet (setting it at the end of ath9k_htc_probe_device() instead of inside
ath9k_tx_init()).
Link: https://lore.kernel.org/r/ed1d2c66-1193-4c81-9542-d514c29ba8b8.bugreport@ubisectech.com
Fixes: 8b3046abc99e ("ath9k_htc: fix NULL pointer dereference at ath9k_htc_tx_get_packet()")
Reported-by: Ubisectech Sirius <bugreport@ubisectech.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240126140218.1033443-1-toke@toke.dk
|
|
The variable ret is being assigned a value but it isn't being
read afterwards. The assignment is redundant and so ret can be
removed.
Cleans up clang scan build warning:
warning: Although the value stored to 'ret' is used in the
enclosing expression, the value is never actually read from
'ret' [deadcode.DeadStores]
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240116155452.2315351-1-colin.i.king@gmail.com
|
|
The following sparse warning was reported:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/fwil.c:432:49:
warning: no newline at end of file
Fixes: 31343230abb1 ("wifi: brcmfmac: export firmware interface functions")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Closes: https://lore.kernel.org/all/20240125165128.7e43a1f3@kernel.org/
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/20240128093057.164791-2-arend.vanspriel@broadcom.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath
ath.git patches for v6.9
We have new features for both ath11k and ath12k. ath12k is now under
heavy refactoring in preparation for MLO support.
Major changes:
ath12k
* refactoring in preparation for Multi-Link Operation (MLO) support
* 1024 Block Ack window size support
* provide firmware wmi logs via a trace event
ath11k
* 36 bit DMA mask support
* support 6 GHz station power modes: Low Power Indoor (LPI), Standard
Power) SP and Very Low Power (VLP)
|
|
The wiphy_work infra ensures that the entire worker will run
with the wiphy mutex. It is useful to have RX handlers
running as a wiphy_work, when we don't want the handler to
run in parallel with mac80211 work (to avoid races).
For example - BT notification can disable eSR starting from the next
patch.
In ieee80211_set_active_links we first check that eSR is
allowed, (drv_can_activate_links) and then activate it.
If the BT notif was received after drv_can_activate_links
(which returned true), and before the activation - eSR will be
activated when it shouldn't.
If BT notif is handled with the wiphy mutex, it can't run in
parallel to ieee80211_set_active_links, which also holds that
mutex.
Add the necessary infrastructure here, for use in the next commit.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240123200528.ce83d16cdec8.I35ef53fa23f58b9ec17924099238b61deafcecd7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This callback checks if a given bitmap of active_links
will be supported by the driver or not.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240123200528.a26fd48bfe3d.I03ae6b4c7fd24e8701660a68cec9403dc3469a0e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Start supporting API version 87 for new devices.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.14cc41da34c4.Ic867f979504c60c21c8182e9adccec9ffbadfe5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This command version adds two news fields:
sbb_bandwidth and sbb_ctrl_channel_loc
They will be populated later.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.82ab4140fff9.Icfba4819fe0b7ac8219ab671c632e25f5fbbaf6f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Without SMP the function is just a stub that returns an error code. Add
a compile time check for CONFIG_SMP in the interest of not logging an
error if setting affinity is not possible anyway.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.ed9094390731.Ic4e5e019c01fd4231b99cf4919af5d19d6353869@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We should - at least for now - advertise common nominal packet
padding of 16µs instead of the more specific PPE thresholds.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.4312e176dfdc.Ide75980ff57257a31e86e6ac5948a8f97aaab577@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Link ID in time event data is -1 when the time event is cleared.
Change the type of the link ID in the time event data structure
and in the affected function from unsigned to signed.
Fixes: 135065837310 ("wifi: iwlwifi: support link_id in SESSION_PROTECTION cmd")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://msgid.link/20240123200528.50d4941f946c.Iea990b118c69bc3e1eb61c1d134c9d470b3a17ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's either the pldr_sync case, in which case we didn't want
or do the retry loops anyway, or things will just continue to
fail. Remove the retry loop that was added in a previous attempt
to address the issue that was later (though still a bit broken)
addressed by the pldr_sync case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.f80a88a18799.I48f21eda090f4cc675f40e99eef69a986d21b500@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the STEP (the interface between MAC and PHY) is in URM
(a lower speed mode) then we cannot use 320 MHz MCS > 9.
Therefore, limit the MCS in our capabilities in this case.
Note that this also limits the TX/rate scaling since that
takes both TX and RX capabilities into account.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.02bae683b7fc.Id5efbb71d45da02c8c4e211d20396637ddd44da8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The driver should not send 160 MHz BW support for 5 GHz
band in HE if PCI subsystem device ID indicates no 160 MHz support.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Reviewed-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240126085924.77c248ce6986.I558e8d0cf19dc862b1c4124df78a4cb690095bb2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no need to print this, it's a known issue and
the workaround works just fine. Make the reallocation
message just a debug message.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.329d5f2ee7f7.I0bfc6dde17fe2c738129f3aba746c6cba57589f9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for the new 802.11be device with limites capabilities:
- 320 MHz isn't supported
- MCSs 12 and 13 are not supported
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.8529bd2acedf.I25dccb7bbeb21b8df2123fad51dde7fcf137a508@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We used to have a test built into the code for this internally,
but now we can put that into kunit and let everyone run it, to
verify the devinfo table ordering if it's changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240123200528.a4a8af7c091f.I0fb09083317b331168b99b8db39656a126a5cc4d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Advertise MLD capabilities and operations in AP mode that
say that up to 15 links are supported simultaneously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240111181514.52a1d48b67e6.Ie459df742944d24d6401683d54d2f3ac44834803@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Advertise EMLSR and EMLMR capability on the AP side to be
a better compliant AP MLD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.dc8786efa787.Ic460c13a91d770c208ac16d0b3e94941bab9b8eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Advertise support for negotiated TTLM in AP mode for testing
purposes. In addition, declare support for some extended
capabilities that are globally advertised by mac80211.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.3f54382f8449.I42b2f7c52f7574448cc8da3ad3db45075e4e0baa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Same as in BSS_CHANGED_VALID_LINKS, set the active
links to all the usable links.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.3c28da3534e9.I76846c5dd693f930d4828e411c734639708b5a1a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Accept the request if all TIDs are mapped to the same link set,
otherwise reject it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Reviewed-by: Gregory Greenman <gregory.greenman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240102213313.dfa8e132d0cd.I5fbec1fef933980819ea39c1227f37d307ab1145@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
PHY loopback turns off link state change signalling. Therefore, the
loopback only works if the link is already up before the PHY loopback is
activated.
Ensure that PHY loopback works even if the link is not already up during
activation by calling netif_carrier_on() explicitly.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Link: https://lore.kernel.org/r/20240123200151.60848-1-gerhard@engleder-embedded.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Previously, each caller of gve_rx_alloc_buffer had to increase counter
and as a result one caller was not tracking those failure. Increasing
counters at a common location now so callers don't have to duplicate
code or miss counter management.
Signed-off-by: Ankit Garg <nktgrg@google.com>
Link: https://lore.kernel.org/r/20240124205435.1021490-1-nktgrg@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.9
The first "new features" pull request for v6.9. We have only driver
changes this time and most of them are for Realtek drivers. Really
nice to see activity in Broadcom drivers again.
Major changes:
rtwl8xxxu
* RTL8188F: concurrent interface support
* Channel Switch Announcement (CSA) support in AP mode
brcmfmac
* per-vendor feature support
* per-vendor SAE password setup
rtlwifi
* speed up USB firmware initialisation
* tag 'wireless-next-2024-01-25' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (105 commits)
wifi: iwlegacy: Use kcalloc() instead of kzalloc()
wifi: rtw89: fix disabling concurrent mode TX hang issue
wifi: rtw89: fix HW scan timeout due to TSF sync issue
wifi: rtw89: add wait/completion for abort scan
wifi: rtw89: fix null pointer access when abort scan
wifi: rtw89: disable RTS when broadcast/multicast
wifi: rtw89: Set default CQM config if not present
wifi: rtw89: refine hardware scan C2H events
wifi: rtw89: refine add_chan H2C command to encode_bits
wifi: rtw89: 8922a: add BTG functions to assist BT coexistence to control TX/RX
wifi: rtw89: 8922a: add TX power related ops
wifi: rtw89: 8922a: add register definitions of H2C, C2H, page, RRSR and EDCCA
wifi: rtw89: 8922a: add chip_ops related to BB init
wifi: rtw89: 8922a: add chip_ops::{enable,disable}_bb_rf
wifi: rtw89: add mlo_dbcc_mode for WiFi 7 chips
wifi: rtlwifi: Speed up firmware loading for USB
wifi: rtl8xxxu: add missing number of sec cam entries for all variants
wifi: brcmfmac: allow per-vendor event handling
wifi: brcmfmac: avoid invalid list operation when vendor attach fails
wifi: brcmfmac: Demote vendor-specific attach/detach messages to info
...
====================
Link: https://lore.kernel.org/r/20240125104030.B6CA6C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts or adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from bpf, netfilter and WiFi.
Jakub is doing a lot of work to include the self-tests in our CI, as a
result a significant amount of self-tests related fixes is flowing in
(and will likely continue in the next few weeks).
Current release - regressions:
- bpf: fix a kernel crash for the riscv 64 JIT
- bnxt_en: fix memory leak in bnxt_hwrm_get_rings()
- revert "net: macsec: use skb_ensure_writable_head_tail to expand
the skb"
Previous releases - regressions:
- core: fix removing a namespace with conflicting altnames
- tc/flower: fix chain template offload memory leak
- tcp:
- make sure init the accept_queue's spinlocks once
- fix autocork on CPUs with weak memory model
- udp: fix busy polling
- mlx5e:
- fix out-of-bound read in port timestamping
- fix peer flow lists corruption
- iwlwifi: fix a memory corruption
Previous releases - always broken:
- netfilter:
- nft_chain_filter: handle NETDEV_UNREGISTER for inet/ingress
basechain
- nft_limit: reject configurations that cause integer overflow
- bpf: fix bpf_xdp_adjust_tail() with XSK zero-copy mbuf, avoiding a
NULL pointer dereference upon shrinking
- llc: make llc_ui_sendmsg() more robust against bonding changes
- smc: fix illegal rmb_desc access in SMC-D connection dump
- dpll: fix pin dump crash for rebound module
- bnxt_en: fix possible crash after creating sw mqprio TCs
- hv_netvsc: calculate correct ring size when PAGE_SIZE is not 4kB
Misc:
- several self-tests fixes for better integration with the netdev CI
- added several missing modules descriptions"
* tag 'net-6.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (88 commits)
tsnep: Fix XDP_RING_NEED_WAKEUP for empty fill ring
tsnep: Remove FCS for XDP data path
net: fec: fix the unhandled context fault from smmu
selftests: bonding: do not test arp/ns target with mode balance-alb/tlb
fjes: fix memleaks in fjes_hw_setup
i40e: update xdp_rxq_info::frag_size for ZC enabled Rx queue
i40e: set xdp_rxq_info::frag_size
xdp: reflect tail increase for MEM_TYPE_XSK_BUFF_POOL
ice: update xdp_rxq_info::frag_size for ZC enabled Rx queue
intel: xsk: initialize skb_frag_t::bv_offset in ZC drivers
ice: remove redundant xdp_rxq_info registration
i40e: handle multi-buffer packets that are shrunk by xdp prog
ice: work on pre-XDP prog frag count
xsk: fix usage of multi-buffer BPF helpers for ZC XDP
xsk: make xsk_buff_pool responsible for clearing xdp_buff::flags
xsk: recycle buffer in case Rx queue was full
net: fill in MODULE_DESCRIPTION()s for rvu_mbox
net: fill in MODULE_DESCRIPTION()s for litex
net: fill in MODULE_DESCRIPTION()s for fsl_pq_mdio
net: fill in MODULE_DESCRIPTION()s for fec
...
|
|
Currently ath11k_mac_op_unassign_vif_chanctx() deletes peer but
ath11k_mac_op_assign_vif_chanctx() doesn't create it. This results in
connection failure if MAC80211 calls drv_unassign_vif_chanctx() and
drv_assign_vif_chanctx() during AUTH and ASSOC, see below log:
[ 102.372431] wlan0: authenticated
[ 102.372585] ath11k_pci 0000:01:00.0: wlan0: disabling HT/VHT/HE as WMM/QoS is not supported by the AP
[ 102.372593] ath11k_pci 0000:01:00.0: mac chanctx unassign ptr ffff895084638598 vdev_id 0
[ 102.372808] ath11k_pci 0000:01:00.0: WMI vdev stop id 0x0
[ 102.383114] ath11k_pci 0000:01:00.0: vdev stopped for vdev id 0
[ 102.384689] ath11k_pci 0000:01:00.0: WMI peer delete vdev_id 0 peer_addr 20:e5:2a:21:c4:51
[ 102.396676] ath11k_pci 0000:01:00.0: htt peer unmap vdev 0 peer 20:e5:2a:21:c4:51 id 3
[ 102.396711] ath11k_pci 0000:01:00.0: peer delete resp for vdev id 0 addr 20:e5:2a:21:c4:51
[ 102.396722] ath11k_pci 0000:01:00.0: mac removed peer 20:e5:2a:21:c4:51 vdev 0 after vdev stop
[ 102.396780] ath11k_pci 0000:01:00.0: mac chanctx assign ptr ffff895084639c18 vdev_id 0
[ 102.400628] wlan0: associate with 20:e5:2a:21:c4:51 (try 1/3)
[ 102.508864] wlan0: associate with 20:e5:2a:21:c4:51 (try 2/3)
[ 102.612815] wlan0: associate with 20:e5:2a:21:c4:51 (try 3/3)
[ 102.720846] wlan0: association with 20:e5:2a:21:c4:51 timed out
The peer delete logic in ath11k_mac_op_unassign_vif_chanctx() is
introduced by commit b4a0f54156ac ("ath11k: move peer delete after
vdev stop of station for QCA6390 and WCN6855") to fix firmware
crash issue caused by unexpected vdev stop/peer delete sequence.
Actually for a STA interface peer should be deleted in
ath11k_mac_op_sta_state() when STA's state changes from
IEEE80211_STA_NONE to IEEE80211_STA_NOTEXIST, which also coincides
with current peer creation design that peer is created during
IEEE80211_STA_NOTEXIST -> IEEE80211_STA_NONE transition. So move
peer delete back to ath11k_mac_op_sta_state(), also stop vdev before
deleting peer to fix the firmware crash issue mentioned there. In
this way the connection failure mentioned here is also fixed.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Fixes: b4a0f54156ac ("ath11k: move peer delete after vdev stop of station for QCA6390 and WCN6855")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-5-quic_bqiang@quicinc.com
|
|
Currently ath11k_mac_start_vdev_delay() needs a forward declaration because
it is defined after where it is called. Avoid this by re-arranging
ath11k_mac_station_add() and ath11k_mac_op_sta_state().
No functional changes. Compile tested only.
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-4-quic_bqiang@quicinc.com
|
|
Rename ath11k_start_vdev_delay() as ath11k_mac_start_vdev_delay()
to follow naming convention.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-3-quic_bqiang@quicinc.com
|
|
In ath11k_mac_op_assign_vif_chanctx(), there is a logic to
create peer using ar->mac_addr for a STA vdev. This is invalid
because a STA vdev should have a peer created using AP's
MAC address. Besides, if we run into that logic, it means a peer
has already been created earlier, we should not create it again.
So remove it.
This is found during code review.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123025700.2929-2-quic_bqiang@quicinc.com
|
|
Currently 32 bit DMA mask is used, telling kernel to get us an DMA
address under 4GB when mapping a buffer. This results in a very high
CPU overhead in the case where IOMMU is disabled and more than 4GB
system memory is installed. The reason is, with more than 4GB memory
installed, kernel is likely to allocate a buffer whose physical
address is above 4GB. While with IOMMU disabled, kernel has to involve
SWIOTLB to map/unmap that buffer, which consumes lots of CPU cycles.
We did hit an issue caused by the reason mentioned above: in a system
that disables IOMMU and gets 8GB memory installed, a total of 40.5%
CPU usage is observed in throughput test. CPU profiling shows nearly
60% of CPU cycles are consumed by SWIOTLB.
By enabling 36 bit DMA mask, we can bypass SWIOTLB for any buffer
whose physical address is below 64GB. There are two types of DMA mask
within struct device, named dma_mask and coherent_dma_mask. Here we
only enable 36 bit for dma_mask, because firmware crashes if
coherent_dma_mask is also enabled, due to some unknown hardware
limitations. This is acceptable because coherent_dma_mask is used for
mapping a consistent DMA buffer, which generally does not happen in
a hot path.
With this change, the total CPU usage mentioned in above issue drops
to 18.9%.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240123015201.28939-1-quic_bqiang@quicinc.com
|
|
Currently the MDIO bus of the switches the MT7530 DSA subdriver controls
can only be registered as non-OF-based. Bring support for registering the
bus OF-based.
The subdrivers that control switches [with MDIO bus] probed on OF must
follow this logic to support all cases properly:
No switch MDIO bus defined: Populate ds->user_mii_bus, register the MDIO
bus, set the interrupts for PHYs if "interrupt-controller" is defined at
the switch node. This case should only be covered for the switches which
their dt-bindings documentation didn't document the MDIO bus from the
start. This is to keep supporting the device trees that do not describe the
MDIO bus on the device tree but the MDIO bus is being used nonetheless.
Switch MDIO bus defined: Don't populate ds->user_mii_bus, register the MDIO
bus, set the interrupts for PHYs if ["interrupt-controller" is defined at
the switch node and "interrupts" is defined at the PHY nodes under the
switch MDIO bus node].
Switch MDIO bus defined but explicitly disabled: If the device tree says
status = "disabled" for the MDIO bus, we shouldn't need an MDIO bus at all.
Instead, just exit as early as possible and do not call any MDIO API.
The use of ds->user_mii_bus is inappropriate when the MDIO bus of the
switch is described on the device tree [1], which is why we don't populate
ds->user_mii_bus in that case.
Link: https://lore.kernel.org/netdev/20231213120656.x46fyad6ls7sqyzv@skbuf/ [1]
Suggested-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20240122053431.7751-1-arinc.unal@arinc9.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The fill ring of the XDP socket may contain not enough buffers to
completey fill the RX queue during socket creation. In this case the
flag XDP_RING_NEED_WAKEUP is not set as this flag is only set if the RX
queue is not completely filled during polling.
Set XDP_RING_NEED_WAKEUP flag also if RX queue is not completely filled
during XDP socket creation.
Fixes: 3fc2333933fd ("tsnep: Add XDP socket zero-copy RX support")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The RX data buffer includes the FCS. The FCS is already stripped for the
normal data path. But for the XDP data path the FCS is included and
acts like additional/useless data.
Remove the FCS from the RX data buffer also for XDP.
Fixes: 65b28c810035 ("tsnep: Add XDP RX support")
Fixes: 3fc2333933fd ("tsnep: Add XDP socket zero-copy RX support")
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5 fixes 2024-01-24
This series provides bug fixes to mlx5 driver.
Please pull and let me know if there is any problem.
* tag 'mlx5-fixes-2024-01-24' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5e: fix a potential double-free in fs_any_create_groups
net/mlx5e: fix a double-free in arfs_create_groups
net/mlx5e: Ignore IPsec replay window values on sender side
net/mlx5e: Allow software parsing when IPsec crypto is enabled
net/mlx5: Use mlx5 device constant for selecting CQ period mode for ASO
net/mlx5: DR, Can't go to uplink vport on RX rule
net/mlx5: DR, Use the right GVMI number for drop action
net/mlx5: Bridge, fix multicast packets sent to uplink
net/mlx5: Fix a WARN upon a callback command failure
net/mlx5e: Fix peer flow lists handling
net/mlx5e: Fix inconsistent hairpin RQT sizes
net/mlx5e: Fix operation precedence bug in port timestamping napi_poll context
net/mlx5: Fix query of sd_group field
net/mlx5e: Use the correct lag ports number when creating TISes
====================
Link: https://lore.kernel.org/r/20240124081855.115410-1-saeed@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
