| Age | Commit message (Collapse) | Author |
|---|
|
The added benefit is that the error code is mentioned in the error message
and its usage is a bit more compact than open coding it. This also
improves behaviour in case devm_clk_get() returns -EPROBE_DEFER.
While touching this code, consistently start error messages with upper
case.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
The size check for state->period is moved to .apply() to make sure that
the values of state->duty_cycle and state->period are passed to
pwm_samsung_config without change while they are discarded to int.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Use if and else instead of if(A) and if (!A).
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
This fixes a small issue in clps711x_get_duty() en passant: the
multiplication v * 0xf might have overflown.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The reg member of struct raspberrypi_pwm_prop is a little endian 32 bit
quantity. Explicitly convert the (native endian) value to little endian
on assignment as is already done in raspberrypi_pwm_set_property().
This fixes the following sparse warning:
drivers/pwm/pwm-raspberrypi-poe.c:69:24: warning: incorrect type in initializer (different base types)
drivers/pwm/pwm-raspberrypi-poe.c:69:24: expected restricted __le32 [usertype] reg
drivers/pwm/pwm-raspberrypi-poe.c:69:24: got unsigned int [usertype] reg
Fixes: 79caa362eab6 ("pwm: Add Raspberry Pi Firmware based PWM bus")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The array atmel_tcb_divisors is not supposed to be used outside of the
driver, so make it static.
This fixes a sparse warning:
drivers/pwm/pwm-atmel-tcb.c:64:10: warning: symbol 'atmel_tcb_divisors' was not declared. Should it be static?
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
pwmchip_add() unconditionally assigns the base ID dynamically. Commit
f9a8ee8c8bcd1 ("pwm: Always allocate PWM chip base ID dynamically")
dropped all base assignment from drivers under drivers/pwm/. It missed
this driver. Fix that.
Fixes: f9a8ee8c8bcd1 ("pwm: Always allocate PWM chip base ID dynamically")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
To eventually get rid of all legacy drivers convert this driver to the
modern world implementing .apply().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The hardware only supports periods <= 1.6 ms and if a bigger period is
requested it is clamped to 1.6 ms. In this case duty_cycle might be bigger
than 1.6 ms and then the duty cycle register is written with a value
bigger than LP3943_MAX_DUTY. So clamp duty_cycle accordingly.
Fixes: af66b3c0934e ("pwm: Add LP3943 PWM driver")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add Sunplus SoC SP7021 PWM Driver
Signed-off-by: Hammer Hsieh <hammerh0314@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This adds PWM support for Xilinx LogiCORE IP AXI soft timers commonly
found on Xilinx FPGAs. At the moment clock control is very basic: we
just enable the clock during probe and pin the frequency. In the future,
someone could add support for disabling the clock when not in use.
Some common code has been specially demarcated. While currently only
used by the PWM driver, it is anticipated that it may be split off in
the future to be used by the timer driver as well.
This driver was written with reference to Xilinx DS764 for v1.03.a [1].
[1] https://www.xilinx.com/support/documentation/ip_documentation/axi_timer/v1_03_a/axi_timer_ds764.pdf
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Per-channel data is tracked using struct pwm_device::chip_data and
struct atmel_tcb_pwm_chip::pwms[]. Simplify by using the latter
consistently.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This fixes a problem that was supposed to be addressed by commit
6eefb79d6f5bc ("pwm: sun4i: Remove erroneous else branch") - backlight
could not be switched off on some Allwinner A20. The commit was
correct, but was not a reliable fix for the problem, which was timing
related.
The real problem for the backlight switching problem was that sleeping
for a full period did not work, because delay_us is always zero.
It is zero because the period (plus 1 microsecond) is rounded down to
the next "jiffies", but the period is less than one jiffy.
On my Cubieboard 2, the period is 5ms, and 1 jiffy (at the default
HZ=100) is 10ms, so nsecs_to_jiffies(10ms+1us)=0.
The roundtrip from nanoseconds to jiffies and back to microseconds is
an unnecessary loss of precision; always rounding down (via
nsecs_to_jiffies()) then causes the breakage.
This patch eliminates this roundtrip, and directly converts from
nanoseconds to microseconds (for usleep_range()), using
DIV_ROUND_UP_ULL() to force rounding up. This way, the sleep time is
never zero, and after the sleep, we are guaranteed to be in a
different period, and the device is ready for another control command
for sure.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Basically this code did "jiffies + period - jiffies", and we can
simply eliminate the "jiffies" time stamp here.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Its value is calculated in sun4i_pwm_apply() and is used only there.
Signed-off-by: Max Kellermann <max.kellermann@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixlet from Juergen Gross:
"A single cleanup patch for the Xen balloon driver"
* tag 'for-linus-5.18-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: don't use PV mode extra memory for zone device allocations
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply fixes from Sebastian Reichel:
- Fix a regression with battery data failing to load from DT
* tag 'for-v5.18-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply:
power: supply: Reset err after not finding static battery
power: supply: samsung-sdi-battery: Add missing charge restart voltages
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Regular set of fixes for drivers and the dev-interface"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: ismt: Fix undefined behavior due to shift overflowing the constant
i2c: dev: Force case user pointers in compat_i2cdev_ioctl()
i2c: dev: check return value when calling dev_set_name()
i2c: qcom-geni: Use dev_err_probe() for GPI DMA error
i2c: imx: Implement errata ERR007805 or e7805 bus frequency limit
i2c: pasemi: Wait for write xfers to finish
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux
Pull gpio fixes from Bartosz Golaszewski:
"A single fix for gpio-sim and two patches for GPIO ACPI pulled from
Andy:
- fix the set/get_multiple() callbacks in gpio-sim
- use correct format characters in gpiolib-acpi
- use an unsigned type for pins in gpiolib-acpi"
* tag 'gpio-fixes-for-v5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: sim: fix setting and getting multiple lines
gpiolib: acpi: Convert type for pin to be unsigned
gpiolib: acpi: use correct format characters
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are a number of SoC bugfixes that came in since the merge
window, and more of them are already pending.
This batch includes:
- A boot time regression fix for davinci that triggered on
multi_v5_defconfig when booting any platform
- Defconfig updates to address removed features, changed symbol names
or dependencies, for gemini, ux500, and pxa
- Email address changes for Krzysztof Kozlowski
- Build warning fixes for ep93xx and iop32x
- Devicetree warning fixes across many platforms
- Minor bugfixes for the reset controller, memory controller and SCMI
firmware subsystems plus the versatile-express board"
* tag 'soc-fixes-5.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (34 commits)
ARM: config: Update Gemini defconfig
arm64: dts: qcom/sdm845-shift-axolotl: Fix boolean properties with values
ARM: dts: align SPI NOR node name with dtschema
ARM: dts: Fix more boolean properties with values
arm/arm64: dts: qcom: Fix boolean properties with values
arm64: dts: imx: Fix imx8*-var-som touchscreen property sizes
arm: dts: imx: Fix boolean properties with values
arm64: dts: tegra: Fix boolean properties with values
arm: dts: at91: Fix boolean properties with values
arm: configs: imote2: Drop defconfig as board support dropped.
ep93xx: clock: Don't use plain integer as NULL pointer
ep93xx: clock: Fix UAF in ep93xx_clk_register_gate()
ARM: vexpress/spc: Fix all the kernel-doc build warnings
ARM: vexpress/spc: Fix kernel-doc build warning for ve_spc_cpu_in_wfi
ARM: config: u8500: Re-enable AB8500 battery charging
ARM: config: u8500: Add some common hardware
memory: fsl_ifc: populate child nodes of buses and mfd devices
ARM: config: Refresh U8500 defconfig
firmware: arm_scmi: Fix sparse warnings in OPTEE transport driver
firmware: arm_scmi: Replace zero-length array with flexible-array member
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator fixes from Jason Donenfeld:
- Per your suggestion, random reads now won't fail if there's a page
fault after some non-zero amount of data has been read, which makes
the behavior consistent with all other reads in the kernel.
- Rather than an inconsistent mix of random_get_entropy() returning an
unsigned long or a cycles_t, now it just returns an unsigned long.
- A memcpy() was replaced with an memmove(), because the addresses are
sometimes overlapping. In practice the destination is always before
the source, so not really an issue, but better to be correct than
not.
* tag 'random-5.18-rc3-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random:
random: use memmove instead of memcpy for remaining 32 bytes
random: make random_get_entropy() return an unsigned long
random: allow partial reads if later user copies fail
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"13 fixes, all in drivers.
The most extensive changes are in the iscsi series (affecting drivers
qedi, cxgbi and bnx2i), the next most is scsi_debug, but that's just a
simple revert and then minor updates to pm80xx"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi: MAINTAINERS: Add Mike Christie as co-maintainer
scsi: qedi: Fix failed disconnect handling
scsi: iscsi: Fix NOP handling during conn recovery
scsi: iscsi: Merge suspend fields
scsi: iscsi: Fix unbound endpoint error handling
scsi: iscsi: Fix conn cleanup and stop race during iscsid restart
scsi: iscsi: Fix endpoint reuse regression
scsi: iscsi: Release endpoint ID when its freed
scsi: iscsi: Fix offload conn cleanup when iscsid restarts
scsi: iscsi: Move iscsi_ep_disconnect()
scsi: pm80xx: Enable upper inbound, outbound queues
scsi: pm80xx: Mask and unmask upper interrupt vectors 32-63
Revert "scsi: scsi_debug: Address races following module load"
|
|
gitolite.kernel.org:pub/scm/linux/kernel/git/andy/linux-gpio-intel into gpio/for-current
intel-gpio for v5.18-2
* Couple of fixes related to handling unsigned value of the pin from ACPI
gpiolib:
- acpi: Convert type for pin to be unsigned
- acpi: use correct format characters
|
|
In order to immediately overwrite the old key on the stack, before
servicing a userspace request for bytes, we use the remaining 32 bytes
of block 0 as the key. This means moving indices 8,9,a,b,c,d,e,f ->
4,5,6,7,8,9,a,b. Since 4 < 8, for the kernel implementations of
memcpy(), this doesn't actually appear to be a problem in practice. But
relying on that characteristic seems a bit brittle. So let's change that
to a proper memmove(), which is the by-the-books way of handling
overlapping memory copies.
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- Fix memory corruption in DM integrity target when tag_size is less
than digest size.
- Fix DM multipath's historical-service-time path selector to not use
sched_clock() and ktime_get_ns(); only use ktime_get_ns().
- Fix dm_io->orig_bio NULL pointer dereference in dm_zone_map_bio() due
to 5.18 changes that overlooked DM zone's use of ->orig_bio
- Fix for regression that broke the use of dm_accept_partial_bio() for
"abnormal" IO (e.g. WRITE ZEROES) that does not need duplicate bios
- Fix DM's issuing of empty flush bio so that it's size is 0.
* tag 'for-5.18/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix bio length of empty flush
dm: allow dm_accept_partial_bio() for dm_io without duplicate bios
dm zone: fix NULL pointer dereference in dm_zone_map_bio
dm mpath: only use ktime_get_ns() in historical selector
dm integrity: fix memory corruption when tag_size is less than digest size
|
|
Fix:
drivers/i2c/busses/i2c-ismt.c: In function ‘ismt_hw_init’:
drivers/i2c/busses/i2c-ismt.c:770:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_400K:
^~~~
drivers/i2c/busses/i2c-ismt.c:773:2: error: case label does not reduce to an integer constant
case ISMT_SPGT_SPD_1M:
^~~~
See https://lore.kernel.org/r/YkwQ6%2BtIH8GQpuct@zn.tnic for the gory
details as to why it triggers with older gccs only.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Seth Heasley <seth.heasley@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Sparse has warned us about wrong address space for user pointers:
i2c-dev.c:561:50: warning: incorrect type in initializer (different address spaces)
i2c-dev.c:561:50: expected unsigned char [usertype] *buf
i2c-dev.c:561:50: got void [noderef] __user *
Force cast the pointer to (__u8 *) that is used by I²C core code.
Note, this is an additional fix to the previously addressed similar issue
in the I2C_RDWR case in the same function.
Fixes: 3265a7e6b41b ("i2c: dev: Add __user annotation")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
If dev_set_name() fails, the dev_name() is null, check the return
value of dev_set_name() to avoid the null-ptr-deref.
Fixes: 1413ef638aba ("i2c: dev: Fix the race between the release of i2c_dev and cdev")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The GPI DMA engine driver can be compiled as a module, in which case the
likely probe deferral "error" shows up in the kernel log. Switch to
using dev_err_probe() to silence this warning and to ensure that
"devices_deferred" in debugfs carries this information.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The i.MX8MP Mask Set Errata for Mask 1P33A, Rev. 2.0 has description of
errata ERR007805 as below. This errata is found on all MX8M{M,N,P,Q},
MX7{S,D}, MX6{UL{,L,Z},S{,LL,X},S,D,DL,Q,DP,QP} . MX7ULP, MX8Q, MX8X
are not affected. MX53 and older status is unknown, as the errata
first appears in MX6 errata sheets from 2016 and the latest errata
sheet for MX53 is from 2015. Older SoC errata sheets predate the
MX53 errata sheet. MX8ULP and MX9 status is unknown as the errata
sheet is not available yet.
"
ERR007805 I2C: When the I2C clock speed is configured for 400 kHz,
the SCL low period violates the I2C spec of 1.3 uS min
Description: When the I2C module is programmed to operate at the
maximum clock speed of 400 kHz (as defined by the I2C spec), the SCL
clock low period violates the I2C spec of 1.3 uS min. The user must
reduce the clock speed to obtain the SCL low time to meet the 1.3us
I2C minimum required. This behavior means the SoC is not compliant
to the I2C spec at 400kHz.
Workaround: To meet the clock low period requirement in fast speed
mode, SCL must be configured to 384KHz or less.
"
Implement the workaround by matching on the affected SoC specific
compatible strings and by limiting the maximum bus frequency in case
the SoC is affected.
Signed-off-by: Marek Vasut <marex@denx.de>
To: linux-i2c@vger.kernel.org
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Wait for completion of write transfers before returning from the driver.
At first sight it may seem advantageous to leave write transfers queued
for the controller to carry out on its own time, but there's a couple of
issues with it:
* Driver doesn't check for FIFO space.
* The queued writes can complete while the driver is in its I2C read
transfer path which means it will get confused by the raising of
XEN (the 'transaction ended' signal). This can cause a spurious
ENODATA error due to premature reading of the MRXFIFO register.
Adding the wait fixes some unreliability issues with the driver. There's
some efficiency cost to it (especially with pasemi_smb_waitready doing
its polling), but that will be alleviated once the driver receives
interrupt support.
Fixes: beb58aa39e6e ("i2c: PA Semi SMBus driver")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
The commit 92986f6b4c8a ("dm: use bio_clone_fast in alloc_io/alloc_tio")
removed bio_clone_fast() call from alloc_tio() when ci->io->tio is
available. In this case, ci->bio is not copied to ci->io->tio.clone.
This is fine since init_clone_info() sets same values to ci->bio and
ci->io->tio.clone.
However, when incoming bios have REQ_PREFLUSH flag, __send_empty_flush()
prepares a zero length bio on stack and set it to ci->bio. At this time,
ci->io->tio.clone still keeps non-zero length. When alloc_tio() chooses
this ci->io->tio.clone as the bio to map, it is passed to targets as
non-empty flush bio. It causes bio length check failure in dm-zoned and
unexpected operation such as dm_accept_partial_bio() call.
To avoid the non-empty flush bio, set zero length to ci->io->tio.clone
in __send_empty_flush().
Fixes: 92986f6b4c8a ("dm: use bio_clone_fast in alloc_io/alloc_tio")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Pull block fixes from Jens Axboe:
- Moving of lower_48_bits() to the block layer and a fix for the
unaligned_be48 added with that originally (Alexander, Keith)
- Fix a bad WARN_ON() for trim size checking (Ming)
- A polled IO timeout fix for null_blk (Ming)
- Silence IO error printing for dead disks (Christoph)
- Compat mode range fix (Khazhismel)
- NVMe pull request via Christoph:
- Tone down the error logging added this merge window a bit
(Chaitanya Kulkarni)
- Quirk devices with non-unique unique identifiers (Christoph)
* tag 'block-5.18-2022-04-15' of git://git.kernel.dk/linux-block:
block: don't print I/O error warning for dead disks
block/compat_ioctl: fix range check in BLKGETSIZE
nvme-pci: disable namespace identifiers for Qemu controllers
nvme-pci: disable namespace identifiers for the MAXIO MAP1002/1202
nvme: add a quirk to disable namespace identifiers
nvme: don't print verbose errors for internal passthrough requests
block: null_blk: end timed out poll request
block: fix offset/size check in bio_trim()
asm-generic: fix __get_unaligned_be48() on 32 bit platforms
block: move lower_48_bits() to block
|
|
Qemu unconditionally reports a UUID, which depending on the qemu version
is either all-null (which is incorrect but harmless) or contains a single
bit set for all controllers. In addition it can also optionally report
a eui64 which needs to be manually set. Disable namespace identifiers
for Qemu controlles entirely even if in some cases they could be set
correctly through manual intervention.
Reported-by: Luis Chamberlain <mcgrof@kernel.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
|
|
The MAXIO MAP1002/1202 controllers reports completely bogus Namespace
identifiers that even change after suspend cycles. Disable using
the Identifiers entirely.
Reported-by: 金韬 <me@kingtous.cn>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Tested-by: 金韬 <me@kingtous.cn>
|
|
Add a quirk to disable using and exporting namespace identifiers for
controllers where they are broken beyond repair.
The most directly visible problem with non-unique namespace identifiers
is that they break the /dev/disk/by-id/ links, with the link for a
supposedly unique identifier now pointing to one of multiple possible
namespaces that share the same ID, and a somewhat random selection of
which one actually shows up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
|
|
Use the RQF_QUIET flag to skip the newly added verbose error reporting,
and set the flag in __nvme_submit_sync_cmd, which is used for most
internal passthrough requests where we do expect errors (e.g. due to
probing for optional functionality). This is similar to what the SCSI
verbose error logging does.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Alan Adamson <alan.adamson@oracle.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Tested-by: Alan Adamson <alan.adamson@oracle.com>
Tested-by: Yi Zhang <yi.zhang@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The intent behind commit e6fc9f62ce6e ("dm: flag clones created by
__send_duplicate_bios") was to formally disallow the use of
dm_accept_partial_bio() where it simply isn't possible -- due to
constraint that multiple bios cannot meaningfully update a shared
tio->len_ptr.
But that commit went too far and disallowed the case where "abormal"
IO (e.g. WRITE_ZEROES) is only using a single bio. Fix this by
not marking a dm_io with a single dm_target_io (and bio), that happens
to be created by __send_duplicate_bios, as DM_TIO_IS_DUPLICATE_BIO.
Also remove 'unsigned *len' parameter from alloc_multiple_bios().
This commit fixes a dm_accept_partial_bio() BUG_ON() with dm-zoned
when a WRITE_ZEROES bio is issued.
Fixes: 655f3aad7aa4 ("dm: switch dm_target_io booleans over to proper flags")
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"Eggs season holidays are among us, and I think I'd expect some smaller
pulls for two weeks then.
This seems eerily quiet. One i915 fix, amdgpu has a bunch and msm. I
didn't see a misc pull this week, so I expect that will catch up next
week.
i915:
- Correct legacy mmap disabling to use GRAPHICS_VER_FULL
msm:
- system suspend fix
- kzalloc return checks
- misc display fix
- iommu_present removal
amdgpu:
- Fix for alpha properly in pre-multiplied mode
- Fix VCN 3.1.2 firmware name
- Suspend/resume fix
- Add a gfxoff quirk for Mac vega20 board
- DCN 3.1.6 spread spectrum fix"
* tag 'drm-fixes-2022-04-15' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: remove dtbclk_ss compensation for dcn316
drm/amdgpu: Enable gfxoff quirk on MacBook Pro
drm/amdgpu: Ensure HDA function is suspended before ASIC reset
drm/amdgpu: fix VCN 3.1.2 firmware name
drm/amd/display: don't ignore alpha property on pre-multiplied mode
drm/msm/gpu: Avoid -Wunused-function with !CONFIG_PM_SLEEP
drm/msm/dp: add fail safe mode outside of event_mutex context
drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()
drm/msm: Stop using iommu_present()
drm/msm/mdp5: check the return of kzalloc()
drm/msm: Fix range size vs end confusion
drm/i915: Sunset igpu legacy mmap support based on GRAPHICS_VER_FULL
drm/msm/dpu: Use indexed array initializer to prevent mismatches
drm/msm/disp: check the return value of kzalloc()
dt-bindings: display/msm: another fix for the dpu-qcm2290 example
drm/msm: Add missing put_task_struct() in debugfs path
drm/msm/gpu: Remove mutex from wait_event condition
drm/msm/gpu: Park scheduler threads for system suspend
drm/msm/gpu: Rename runtime suspend/resume functions
|
|
Pull vfio fix from Alex Williamson:
- Fix VF token checking for vfio-pci variant drivers (Jason Gunthorpe)
* tag 'vfio-v5.18-rc3' of https://github.com/awilliam/linux-vfio:
vfio/pci: Fix vf_token mechanism when device-specific VF drivers are used
|
|
https://gitlab.freedesktop.org/agd5f/linux into drm-fixes
amd-drm-fixes-5.18-2022-04-13:
amdgpu:
- Fix for alpha properly in pre-multiplied mode
- Fix VCN 3.1.2 firmware name
- Suspend/resume fix
- Add a gfxoff quirk for Mac vega20 board
- DCN 3.1.6 spread spectrum fix
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414025821.5811-1-alexander.deucher@amd.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Paolo Abeni:
"Including fixes from wireless and netfilter.
Current release - regressions:
- smc: fix af_ops of child socket pointing to released memory
- wifi: ath9k: fix usage of driver-private space in tx_info
Previous releases - regressions:
- ipv6: fix panic when forwarding a pkt with no in6 dev
- sctp: use the correct skb for security_sctp_assoc_request
- smc: fix NULL pointer dereference in smc_pnet_find_ib()
- sched: fix initialization order when updating chain 0 head
- phy: don't defer probe forever if PHY IRQ provider is missing
- dsa: revert "net: dsa: setup master before ports"
- dsa: felix: fix tagging protocol changes with multiple CPU ports
- eth: ice:
- fix use-after-free when freeing @rx_cpu_rmap
- revert "iavf: fix deadlock occurrence during resetting VF
interface"
- eth: lan966x: stop processing the MAC entry is port is wrong
Previous releases - always broken:
- sched:
- flower: fix parsing of ethertype following VLAN header
- taprio: check if socket flags are valid
- nfc: add flush_workqueue to prevent uaf
- veth: ensure eth header is in skb's linear part
- eth: stmmac: fix altr_tse_pcs function when using a fixed-link
- eth: macb: restart tx only if queue pointer is lagging
- eth: macvlan: fix leaking skb in source mode with nodst option"
* tag 'net-5.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (52 commits)
net: bcmgenet: Revert "Use stronger register read/writes to assure ordering"
rtnetlink: Fix handling of disabled L3 stats in RTM_GETSTATS replies
net: dsa: felix: fix tagging protocol changes with multiple CPU ports
tun: annotate access to queue->trans_start
nfc: nci: add flush_workqueue to prevent uaf
net: dsa: realtek: don't parse compatible string for RTL8366S
net: dsa: realtek: fix Kconfig to assure consistent driver linkage
net: ftgmac100: access hardware register after clock ready
Revert "net: dsa: setup master before ports"
macvlan: Fix leaking skb in source mode with nodst option
netfilter: nf_tables: nft_parse_register can return a negative value
net: lan966x: Stop processing the MAC entry is port is wrong.
net: lan966x: Fix when a port's upper is changed.
net: lan966x: Fix IGMP snooping when frames have vlan tag
net: lan966x: Update lan966x_ptp_get_nominal_value
sctp: Initialize daddr on peeled off socket
net/smc: Fix af_ops of child socket pointing to released memory
net/smc: Fix NULL pointer dereference in smc_pnet_find_ib()
net/smc: use memcpy instead of snprintf to avoid out of bounds read
net: macb: Restart tx only if queue pointer is lagging
...
|
|
When poll request is timed out, it is removed from the poll list,
but not completed, so the request is leaked, and never get chance
to complete.
Fix the issue by ending it in timeout handler.
Fixes: 0a593fbbc245 ("null_blk: poll queue support")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Link: https://lore.kernel.org/r/20220413084836.1571995-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We need to take mask into account in the set/get_multiple() callbacks.
Use bitmap_replace() instead of bitmap_copy().
Fixes: cb8c474e79be ("gpio: sim: new testing module")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
It turns out after digging deeper into this bug, that it was being
triggered by GCC12 failing to call the bcmgenet_enable_dma()
routine. Given that a gcc12 fix has been merged [1] and the genet
driver now works properly when built with gcc12, this commit should
be reverted.
[1]
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=105160
https://gcc.gnu.org/git/?p=gcc.git;a=commit;h=aabb9a261ef060cf24fd626713f1d7d9df81aa57
Fixes: 8d3ea3d402db ("net: bcmgenet: Use stronger register read/writes to assure ordering")
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220412210420.1129430-1-jeremy.linton@arm.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When the device tree has 2 CPU ports defined, a single one is active
(has any dp->cpu_dp pointers point to it). Yet the second one is still a
CPU port, and DSA still calls ->change_tag_protocol on it.
On the NXP LS1028A, the CPU ports are ports 4 and 5. Port 4 is the
active CPU port and port 5 is inactive.
After the following commands:
# Initial setting
cat /sys/class/net/eno2/dsa/tagging
ocelot
echo ocelot-8021q > /sys/class/net/eno2/dsa/tagging
echo ocelot > /sys/class/net/eno2/dsa/tagging
traffic is now broken, because the driver has moved the NPI port from
port 4 to port 5, unbeknown to DSA.
The problem can be avoided by detecting that the second CPU port is
unused, and not doing anything for it. Further rework will be needed
when proper support for multiple CPU ports is added.
Treat this as a bug and prepare current kernels to work in single-CPU
mode with multiple-CPU DT blobs.
Fixes: adb3dccf090b ("net: dsa: felix: convert to the new .change_tag_protocol DSA API")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220412172209.2531865-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit 5337824f4dc4 ("net: annotate accesses to queue->trans_start")
introduced a new helper, txq_trans_cond_update, to update
queue->trans_start using WRITE_ONCE. One snippet in drivers/net/tun.c
was missed, as it was introduced roughly at the same time.
Fixes: 5337824f4dc4 ("net: annotate accesses to queue->trans_start")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Antoine Tenart <atenart@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220412135852.466386-1-atenart@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
https://gitlab.freedesktop.org/drm/msm into drm-fixes
Some msm fixes for v5.18.
kzalloc return checks, display fix, misc locking and scheduler bug, iommu present removal.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGvuTwx09MKwK68KWXqi4o7LxDGMUz1=Z7xOS+i=OV84Ug@mail.gmail.com
|
|
[why]
dcn316's dtbclk is from non_ss clock source.
no compensation required here.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Enabling gfxoff quirk results in perfectly usable graphical user
interface on MacBook Pro (15-inch, 2019) with Radeon Pro Vega 20 4 GB.
Without the quirk, X server is completely unusable as every few seconds
there is gpu reset due to ring gfx timeout.
Signed-off-by: Tomasz Moń <desowin@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
