| Age | Commit message (Collapse) | Author |
|---|
|
* Use common helpers, bitmap_zalloc() and kstrndup(), to replace open
coded versions.
* Clarify the comments around hotplug vs initial init case for the nfit
driver.
* Cleanup the libnvdimm init path.
|
|
The security implementation is too chatty. For example, the common case
is that security is not enabled / setup, and booting a qemu
configuration currently yields:
nvdimm nmem0: request_key() found no key
nvdimm nmem0: failed to unlock dimm: -126
nvdimm nmem1: request_key() found no key
nvdimm nmem1: failed to unlock dimm: -126
Convert all security related log messages to debug level.
Cc: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add nfit_test support for DSM functions "Get Security State",
"Set Passphrase", "Disable Passphrase", "Unlock Unit", "Freeze Lock",
and "Secure Erase" for the fake DIMMs.
Also adding a sysfs knob in order to put the DIMMs in "locked" state. The
order of testing DIMM unlocking would be.
1a. Disable DIMM X.
1b. Set Passphrase to DIMM X.
2. Write to
/sys/devices/platform/nfit_test.0/nfit_test_dimm/test_dimmX/lock_dimm
3. Renable DIMM X
4. Check DIMM X state via sysfs "security" attribute for nmemX.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
With Intel DSM 1.8 [1] two new security DSMs are introduced. Enable/update
master passphrase and master secure erase. The master passphrase allows
a secure erase to be performed without the user passphrase that is set on
the NVDIMM. The commands of master_update and master_erase are added to
the sysfs knob in order to initiate the DSMs. They are similar in opeartion
mechanism compare to update and erase.
[1]: http://pmem.io/documents/NVDIMM_DSM_Interface-V1.8.pdf
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add support for the NVDIMM_FAMILY_INTEL "ovewrite" capability as
described by the Intel DSM spec v1.7. This will allow triggering of
overwrite on Intel NVDIMMs. The overwrite operation can take tens of
minutes. When the overwrite DSM is issued successfully, the NVDIMMs will
be unaccessible. The kernel will do backoff polling to detect when the
overwrite process is completed. According to the DSM spec v1.7, the 128G
NVDIMMs can take up to 15mins to perform overwrite and larger DIMMs will
take longer.
Given that overwrite puts the DIMM in an indeterminate state until it
completes introduce the NDD_SECURITY_OVERWRITE flag to prevent other
operations from executing when overwrite is happening. The
NDD_WORK_PENDING flag is added to denote that there is a device reference
on the nvdimm device for an async workqueue thread context.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add support to issue a secure erase DSM to the Intel nvdimm. The
required passphrase is acquired from an encrypted key in the kernel user
keyring. To trigger the action, "erase <keyid>" is written to the
"security" sysfs attribute.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add support for enabling and updating passphrase on the Intel nvdimms.
The passphrase is the an encrypted key in the kernel user keyring.
We trigger the update via writing "update <old_keyid> <new_keyid>" to the
sysfs attribute "security". If no <old_keyid> exists (for enabling
security) then a 0 should be used.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add support to disable passphrase (security) for the Intel nvdimm. The
passphrase used for disabling is pulled from an encrypted-key in the kernel
user keyring. The action is triggered by writing "disable <keyid>" to the
sysfs attribute "security".
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add support to unlock the dimm via the kernel key management APIs. The
passphrase is expected to be pulled from userspace through keyutils.
The key management and sysfs attributes are libnvdimm generic.
Encrypted keys are used to protect the nvdimm passphrase at rest. The
master key can be a trusted-key sealed in a TPM, preferred, or an
encrypted-key, more flexible, but more exposure to a potential attacker.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add support for freeze security on Intel nvdimm. This locks out any
changes to security for the DIMM until a hard reset of the DIMM is
performed. This is triggered by writing "freeze" to the generic
nvdimm/nmemX "security" sysfs attribute.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Some NVDIMMs, like the ones defined by the NVDIMM_FAMILY_INTEL command
set, expose a security capability to lock the DIMMs at poweroff and
require a passphrase to unlock them. The security model is derived from
ATA security. In anticipation of other DIMMs implementing a similar
scheme, and to abstract the core security implementation away from the
device-specific details, introduce nvdimm_security_ops.
Initially only a status retrieval operation, ->state(), is defined,
along with the base infrastructure and definitions for future
operations.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Co-developed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The generated dimm id is needed for the sysfs attribute as well as being
used as the identifier/description for the security key. Since it's
constant and should never change, store it as a member of struct nvdimm.
As nvdimm_create() continues to grow parameters relative to NFIT driver
requirements, do not require other implementations to keep pace.
Introduce __nvdimm_create() to carry the new parameters and keep
nvdimm_create() with the long standing default api.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
kstrndup() takes care of '\0' terminator for the strings.
Use it here instead of kmemdup() + explicit terminating the input string.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Add detailed explanation for why it's ok to return 0 if we fail to find
an NFIT at startup. Refer to chapter 9.20.2 NVDIMM Root Device in ACPI
6.2 spec.
Signed-off-by: Ocean He <hehy1@lenovo.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The id check was not executed immediately following ida_simple_get. Just
change the codes position, without function change.
Signed-off-by: Ocean He <hehy1@lenovo.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull networking fixes from David Miller:
"A decent batch of fixes here. I'd say about half are for problems that
have existed for a while, and half are for new regressions added in
the 4.20 merge window.
1) Fix 10G SFP phy module detection in mvpp2, from Baruch Siach.
2) Revert bogus emac driver change, from Benjamin Herrenschmidt.
3) Handle BPF exported data structure with pointers when building
32-bit userland, from Daniel Borkmann.
4) Memory leak fix in act_police, from Davide Caratti.
5) Check RX checksum offload in RX descriptors properly in aquantia
driver, from Dmitry Bogdanov.
6) SKB unlink fix in various spots, from Edward Cree.
7) ndo_dflt_fdb_dump() only works with ethernet, enforce this, from
Eric Dumazet.
8) Fix FID leak in mlxsw driver, from Ido Schimmel.
9) IOTLB locking fix in vhost, from Jean-Philippe Brucker.
10) Fix SKB truesize accounting in ipv4/ipv6/netfilter frag memory
limits otherwise namespace exit can hang. From Jiri Wiesner.
11) Address block parsing length fixes in x25 from Martin Schiller.
12) IRQ and ring accounting fixes in bnxt_en, from Michael Chan.
13) For tun interfaces, only iface delete works with rtnl ops, enforce
this by disallowing add. From Nicolas Dichtel.
14) Use after free in liquidio, from Pan Bian.
15) Fix SKB use after passing to netif_receive_skb(), from Prashant
Bhole.
16) Static key accounting and other fixes in XPS from Sabrina Dubroca.
17) Partially initialized flow key passed to ip6_route_output(), from
Shmulik Ladkani.
18) Fix RTNL deadlock during reset in ibmvnic driver, from Thomas
Falcon.
19) Several small TCP fixes (off-by-one on window probe abort, NULL
deref in tail loss probe, SNMP mis-estimations) from Yuchung
Cheng"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (93 commits)
net/sched: cls_flower: Reject duplicated rules also under skip_sw
bnxt_en: Fix _bnxt_get_max_rings() for 57500 chips.
bnxt_en: Fix NQ/CP rings accounting on the new 57500 chips.
bnxt_en: Keep track of reserved IRQs.
bnxt_en: Fix CNP CoS queue regression.
net/mlx4_core: Correctly set PFC param if global pause is turned off.
Revert "net/ibm/emac: wrong bit is used for STA control"
neighbour: Avoid writing before skb->head in neigh_hh_output()
ipv6: Check available headroom in ip6_xmit() even without options
tcp: lack of available data can also cause TSO defer
ipv6: sr: properly initialize flowi6 prior passing to ip6_route_output
mlxsw: spectrum_switchdev: Fix VLAN device deletion via ioctl
mlxsw: spectrum_router: Relax GRE decap matching check
mlxsw: spectrum_switchdev: Avoid leaking FID's reference count
mlxsw: spectrum_nve: Remove easily triggerable warnings
ipv4: ipv6: netfilter: Adjust the frag mem limit when truesize changes
sctp: frag_point sanity check
tcp: fix NULL ref in tail loss probe
tcp: Do not underestimate rwnd_limited
net: use skb_list_del_init() to remove from RX sublists
...
|
|
The CP rings are accounted differently on the new 57500 chips. There
must be enough CP rings for the sum of RX and TX rings on the new
chips. The current logic may be over-estimating the RX and TX rings.
The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips. We need to introduce a new
bnxt_nq_rings_in_use(). On legacy chips, the 2 functions are the
same and one will just call the other. On the new chips, they
refer to the 2 separate ring structures. The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.
On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.
Fixes: 41e8d7983752 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector. To better unify this, add a resv_irqs
field to struct bnxt_hw_resc. On legacy chips, we initialize resv_irqs
with resv_cp_rings. On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent changes to support the 57500 devices have created this
regression. The bnxt_hwrm_queue_qportcfg() call was moved to be
called earlier before the RDMA support was determined, causing
the CoS queues configuration to be set before knowing whether RDMA
was supported or not. Fix it by moving it to the right place right
after RDMA support is determined.
Fixes: 98f04cf0f1fc ("bnxt_en: Check context memory requirements from firmware.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small driver fixes for 4.20-rc6.
There is a hyperv fix that for some reaon took forever to get into a
shape that could be applied to the tree properly, but resolves a much
reported issue. The others are some gnss patches, one a bugfix and the
two others updates to the MAINTAINERS file to properly match the gnss
files in the tree.
All have been in linux-next for a while with no reported issues"
* tag 'char-misc-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
MAINTAINERS: exclude gnss from SIRFPRIMA2 regex matching
MAINTAINERS: add gnss scm tree
gnss: sirf: fix activation retry handling
Drivers: hv: vmbus: Offload the handling of channels to two workqueues
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg KH:
"Here are two staging driver bugfixes for 4.20-rc6.
One is a revert of a previously incorrect patch that was merged a
while ago, and the other resolves a possible buffer overrun that was
found by code inspection.
Both of these have been in the linux-next tree with no reported
issues"
* tag 'staging-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert commit ef9209b642f "staging: rtl8723bs: Fix indenting errors and an off-by-one mistake in core/rtw_mlme_ext.c"
staging: rtl8712: Fix possible buffer overrun
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty driver fixes from Greg KH:
"Here are three small tty driver fixes for 4.20-rc6
Nothing major, just some bug fixes for reported issues. Full details
are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
kgdboc: fix KASAN global-out-of-bounds bug in param_set_kgdboc_var()
tty: serial: 8250_mtk: always resume the device in probe.
tty: do not set TTY_IO_ERROR flag if console port
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes for 4.20-rc6
The "largest" here are some xhci fixes for reported issues. Also here
is a USB core fix, some quirk additions, and a usb-serial fix which
required the export of one of the tty layer's functions to prevent
code duplication. The tty maintainer agreed with this change.
All of these have been in linux-next with no reported issues"
* tag 'usb-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: Prevent U1/U2 link pm states if exit latency is too long
xhci: workaround CSS timeout on AMD SNPS 3.0 xHC
USB: check usb_get_extra_descriptor for proper size
USB: serial: console: fix reported terminal settings
usb: quirk: add no-LPM quirk on SanDisk Ultra Flair device
USB: Fix invalid-free bug in port_over_current_notify()
usb: appledisplay: Add 27" Apple Cinema Display
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A regression fix for the Address Range Scrub implementation, yes
another one, and support for platforms that misalign persistent memory
relative to the Linux memory hotplug section constraint. Longer term,
support for sub-section memory hotplug would alleviate alignment
waste, but until then this hack allows a 'struct page' memmap to be
established for these misaligned memory regions.
These have all appeared in a -next release, and thanks to Patrick for
reporting and testing the alignment padding fix.
Summary:
- Unless and until the core mm handles memory hotplug units smaller
than a section (128M), persistent memory namespaces must be padded
to section alignment.
The libnvdimm core already handled section collision with "System
RAM", but some configurations overlap independent "Persistent
Memory" ranges within a section, so additional padding injection is
added for that case.
- The recent reworks of the ARS (address range scrub) state machine
to reduce the number of state flags inadvertantly missed a
conversion of acpi_nfit_ars_rescan() call sites. Fix the regression
whereby user-requested ARS results in a "short" scrub rather than a
"long" scrub.
- Fixup the unit tests to handle / test the 128M section alignment of
mocked test resources.
* tag 'libnvdimm-fixes-4.20-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
acpi/nfit: Fix user-initiated ARS to be "ARS-long" rather than "ARS-short"
libnvdimm, pfn: Pad pfn namespaces relative to other regions
tools/testing/nvdimm: Align test resources to 128M
|
|
rx_ppp and tx_ppp can be set between 0 and 255, so don't clamp to 1.
Fixes: 6e8814ceb7e8 ("net/mlx4_en: Fix mixed PFC and Global pause user control requests")
Signed-off-by: Tarick Bedeir <tarick@google.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC fixes from Eduardo Valentin:
"Fixes for armada and broadcom thermal drivers"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: broadcom: constify thermal_zone_of_device_ops structure
thermal: armada: constify thermal_zone_of_device_ops structure
thermal: bcm2835: Switch to SPDX identifier
thermal: armada: fix legacy resource fixup
thermal: armada: fix legacy validity test sense
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A few clk driver fixes this time:
- Introduce protected-clock DT binding to fix breakage on qcom
sdm845-mtp boards where the qspi clks introduced this merge window
cause the firmware on those boards to take down the system if we
try to read the clk registers
- Fix a couple off-by-one errors found by Dan Carpenter
- Handle failure in zynq fixed factor clk driver to avoid using
uninitialized data"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: zynqmp: Off by one in zynqmp_is_valid_clock()
clk: mmp: Off by one in mmp_clk_add()
clk: mvebu: Off by one bugs in cp110_of_clk_get()
arm64: dts: qcom: sdm845-mtp: Mark protected gcc clocks
clk: qcom: Support 'protected-clocks' property
dt-bindings: clk: Introduce 'protected-clocks' property
clk: zynqmp: handle fixed factor param query error
|
|
This reverts commit 624ca9c33c8a853a4a589836e310d776620f4ab9.
This commit is completely bogus. The STACR register has two formats, old
and new, depending on the version of the IP block used. There's a pair of
device-tree properties that can be used to specify the format used:
has-inverted-stacr-oc
has-new-stacr-staopc
What this commit did was to change the bit definition used with the old
parts to match the new parts. This of course breaks the driver on all
the old ones.
Instead, the author should have set the appropriate properties in the
device-tree for the variant used on his board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull vhost/virtio fixes from Michael Tsirkin:
"A couple of last-minute fixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/vsock: fix use-after-free in network stack callers
virtio/s390: fix race in ccw_io_helper()
virtio/s390: avoid race on vcdev->config
vhost/vsock: fix reset orphans race with close timeout
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"Revert ASPM change that caused a regression"
* tag 'pci-v4.20-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI/ASPM: Do not initialize link state when aspm_disabled is set"
|
|
Pull block fixes from Jens Axboe:
"Let's try this again...
We're finally happy with the DM livelock issue, and it's also passed
overnight testing and the corruption regression test. The end result
is much nicer now too, which is great.
Outside of that fix, there's a pull request for NVMe with two small
fixes, and a regression fix for BFQ from this merge window. The BFQ
fix looks bigger than it is, it's 90% comment updates"
* tag 'for-linus-20181207' of git://git.kernel.dk/linux-block:
blk-mq: punt failed direct issue to dispatch list
nvmet-rdma: fix response use after free
nvme: validate controller state before rescheduling keep alive
block, bfq: fix decrement of num_active_groups
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A set of driver bugfixes for the I2C subsystem"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: uniphier-f: fix violation of tLOW requirement for Fast-mode
i2c: uniphier: fix violation of tLOW requirement for Fast-mode
i2c: uniphier-f: fill TX-FIFO only in IRQ handler for repeated START
i2c: uniphier-f: fix timeout error after reading 8 bytes
i2c: scmi: Fix probe error on devices with an empty SMB0001 ACPI device node
i2c: axxia: properly handle master timeout
i2c: rcar: check bus state before reinitializing
i2c: nvidia-gpu: limit reads also for combined messages
i2c: nvidia-gpu: adhere to I2C fault codes
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Another pull request for dmaengine. We got bunch of fixes early this
week and all are tagged to stable. Hope this is last fix for this
cycle:
- Fix imx-sdma handling of channel terminations, this involves
reverting two commits and implement async termination
- Fix cppi dma channel deletion from pending list on stop
- Fix FIFO size for dw controller in Intel Merrifield"
* tag 'dmaengine-fix-4.20-rc6' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: dw: Fix FIFO size for Intel Merrifield
dmaengine: cppi41: delete channel from pending list when stop channel
dmaengine: imx-sdma: use GFP_NOWAIT for dma descriptor allocations
dmaengine: imx-sdma: implement channel termination via worker
Revert "dmaengine: imx-sdma: alloclate bd memory from dma pool"
Revert "dmaengine: imx-sdma: Use GFP_NOWAIT for dma allocations"
|
|
nvmet_rdma_release_rsp() may free the response before using it at error
flow.
Fixes: 8407879 ("nvmet-rdma: fix possible bogus dereference under heavy load")
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Delete operations are seeing NULL pointer references in call_timer_fn.
Tracking these back, the timer appears to be the keep alive timer.
nvme_keep_alive_work() which is tied to the timer that is cancelled
by nvme_stop_keep_alive(), simply starts the keep alive io but doesn't
wait for it's completion. So nvme_stop_keep_alive() only stops a timer
when it's pending. When a keep alive is in flight, there is no timer
running and the nvme_stop_keep_alive() will have no affect on the keep
alive io. Thus, if the io completes successfully, the keep alive timer
will be rescheduled. In the failure case, delete is called, the
controller state is changed, the nvme_stop_keep_alive() is called while
the io is outstanding, and the delete path continues on. The keep
alive happens to successfully complete before the delete paths mark it
as aborted as part of the queue termination, so the timer is restarted.
The delete paths then tear down the controller, and later on the timer
code fires and the timer entry is now corrupt.
Fix by validating the controller state before rescheduling the keep
alive. Testing with the fix has confirmed the condition above was hit.
Signed-off-by: James Smart <jsmart2021@gmail.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/johan/gnss into char-misc-linus
Johan writes:
GNSS fixes for 4.20-rc6
Here's a fix for a broken activation retry loop in the sirf driver.
Included are also two MAINTAINERS updates.
All have been in linux-next with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'gnss-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/gnss:
MAINTAINERS: exclude gnss from SIRFPRIMA2 regex matching
MAINTAINERS: add gnss scm tree
gnss: sirf: fix activation retry handling
|
|
Pull drm fixes from Dave Airlie:
"There's a bit more in here than I'd like, and I'm hoping things calm
down when I'm out.
msm:
- a bunch of display fixes for the new DPU
- a couple of command submission fixes
omap:
- some DSI fixes
ast:
- driver unload crash fix
core:
- fix the lease uevent so userspace can distinguish it
amd:
- fix a bpc regression
- fix lru handling regression
- fixed firmware support for new GPUs
- power management fixes for vega20"
* tag 'drm-fixes-2018-12-07' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/ast: Fix connector leak during driver unload
drm/amdgpu/vcn: Update vcn.cur_state during suspend
drm/amd/display: Fix overflow/truncation from strncpy.
drm/amd/powerplay: improve OD code robustness
drm/amdgpu: enlarge maximum waiting time of KIQ
drm/fb-helper: Fix typo in parameter description
drm/amd/powerplay: support SoftMin/Max setting for some specific DPM
drm/amd/powerplay: issue pre-display settings for display change event
drm/amd/powerplay: support new pptable upload on Vega20
drm/amdgpu/gmc8: always load MC firmware in the driver
drm/amdgpu/gmc8: update MC firmware for polaris
drm/amdgpu: update mc firmware image for polaris12 variants
drm/msm: Fix error return checking
drm/msm/dpu: Ignore alpha for XBGR8888 format
drm/msm: dpu: Fix "WARNING: invalid free of devm_ allocated data"
drm/msm/hdmi: Drop pointless static qualifier in msm_hdmi_bind()
drm/msm: Move fence put to where failure occurs
drm/msm: dpu: Don't set legacy plane->crtc pointer
drm/msm/gpu: Don't map command buffers with nr_relocs equal to 0
drm/msm/hdmi: Enable HPD after HDMI IRQ is set up
...
|
|
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently, the clock duty is set as tLOW/tHIGH = 1/1. For Fast-mode,
tLOW is set to 1.25 us while the I2C spec requires tLOW >= 1.3 us.
tLOW/tHIGH = 5/4 would meet both Standard-mode and Fast-mode:
Standard-mode: tLOW = 5.56 us, tHIGH = 4.44 us
Fast-mode: tLOW = 1.39 us, tHIGH = 1.11 us
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
- For a repeated START condition, this controller starts data transfer
immediately after the slave address is written to the TX-FIFO.
- Once the TX-FIFO empty interrupt is asserted, the controller makes
a pause even if additional data are written to the TX-FIFO.
Given those circumstances, the data after a repeated START may not be
transferred if the interrupt is asserted while the TX-FIFO is being
filled up. A more reliable way is to append TX data only in the
interrupt handler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
I was totally screwed up in commit eaba68785c2d ("i2c: uniphier-f:
fix race condition when IRQ is cleared"). Since that commit, if the
number of read bytes is multiple of the FIFO size (8, 16, 24... bytes),
the STOP condition could be issued twice, depending on the timing.
If this happens, the controller will go wrong, resulting in the timeout
error.
It was more than 3 years ago when I wrote this driver, so my memory
about this hardware was vague. Please let me correct the description
in the commit log of eaba68785c2d.
Clearing the IRQ status on exiting the IRQ handler is absolutely
fine. This controller makes a pause while any IRQ status is asserted.
If the IRQ status is cleared first, the hardware may start the next
transaction before the IRQ handler finishes what it supposed to do.
This partially reverts the bad commit with clear comments so that I
will never repeat this mistake.
I also investigated what is happening at the last moment of the read
mode. The UNIPHIER_FI2C_INT_RF interrupt is asserted a bit earlier
(by half a period of the clock cycle) than UNIPHIER_FI2C_INT_RB.
I consulted a hardware engineer, and I got the following information:
UNIPHIER_FI2C_INT_RF
asserted at the falling edge of SCL at the 8th bit.
UNIPHIER_FI2C_INT_RB
asserted at the rising edge of SCL at the 9th (ACK) bit.
In order to avoid calling uniphier_fi2c_stop() twice, check the latter
interrupt. I also commented this because it is obscure hardware internal.
Fixes: eaba68785c2d ("i2c: uniphier-f: fix race condition when IRQ is cleared")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Some AMD based HP laptops have a SMB0001 ACPI device node which does not
define any methods.
This leads to the following error in dmesg:
[ 5.222731] cmi: probe of SMB0001:00 failed with error -5
This commit makes acpi_smbus_cmi_add() return -ENODEV instead in this case
silencing the error. In case of a failure of the i2c_add_adapter() call
this commit now propagates the error from that call instead of -EIO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
According to Intel (R) Axxia TM Lionfish Communication Processor
Peripheral Subsystem Hardware Reference Manual, the AXXIA I2C module
have a programmable Master Wait Timer, which among others, checks the
time between commands send in manual mode. When a timeout (25ms) passes,
TSS bit is set in Master Interrupt Status register and a Stop command is
issued by the hardware.
The axxia_i2c_xfer(), does not properly handle this situation, however.
For each message a separate axxia_i2c_xfer_msg() is called and this
function incorrectly assumes that any interrupt might happen only when
waiting for completion. This is mostly correct but there is one
exception - a master timeout can trigger if enough time has passed
between individual transfers. It will, by definition, happen between
transfers when the interrupts are disabled by the code. If that happens,
the hardware issues Stop command.
The interrupt indicating timeout will not be triggered as soon as we
enable them since the Master Interrupt Status is cleared when master
mode is entered again (which happens before enabling irqs) meaning this
error is lost and the transfer is continued even though the Stop was
issued on the bus. The subsequent operations completes without error but
a bogus value (0xFF in case of read) is read as the client device is
confused because aborted transfer. No error is returned from
master_xfer() making caller believe that a valid value was read.
To fix the problem, the TSS bit (indicating timeout) in Master Interrupt
Status register is checked before each transfer. If it is set, there was
a timeout before this transfer and (as described above) the hardware
already issued Stop command so the transaction should be aborted thus
-ETIMEOUT is returned from the master_xfer() callback. In order to be
sure no timeout was issued we can't just read the status just before
starting new transaction as there will always be a small window of time
(few CPU cycles at best) where this might still happen. For this reason
we have to temporally disable the timer before checking for TSS bit.
Disabling it will, however, clear the TSS bit so in order to preserve
that information, we have to read it in ISR so we have to ensure that
the TSS interrupt is not masked between transfers of one transaction.
There is no need to call bus recovery or controller reinitialization if
that happens so it's skipped.
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.
The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.
Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d26950 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().
Drop the reference when this unlikely error is hit.
Fixes: 1c30d1836aeb ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.
Fix by removing these warnings for now.
Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.
Fixes: 6e6030bd5412 ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the network stack calls .send_pkt()/.cancel_pkt() during .release(),
a struct vhost_vsock use-after-free is possible. This occurs because
.release() does not wait for other CPUs to stop using struct
vhost_vsock.
Switch to an RCU-enabled hashtable (indexed by guest CID) so that
.release() can wait for other CPUs by calling synchronize_rcu(). This
also eliminates vhost_vsock_lock acquisition in the data path so it
could have a positive effect on performance.
This is CVE-2018-14625 "kernel: use-after-free Read in vhost_transport_send_pkt".
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+bd391451452fb0b93039@syzkaller.appspotmail.com
Reported-by: syzbot+e3e074963495f92a89ed@syzkaller.appspotmail.com
Reported-by: syzbot+d5a0a170c5069658b141@syzkaller.appspotmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
