| Age | Commit message (Collapse) | Author |
|---|
|
Pull networking fixes from David Miller:
1) e1000e computes header length incorrectly wrt vlans, fix from Vlad
Yasevich.
2) ns_capable() check in sock_diag netlink code, from Andrew
Lutomirski.
3) Fix invalid queue pairs handling in virtio_net, from Amos Kong.
4) Checksum offloading busted in sxgbe driver due to incorrect
descriptor layout, fix from Byungho An.
5) Fix build failure with SMC_DEBUG set to 2 or larger, from Zi Shen
Lim.
6) Fix uninitialized A and X registers in BPF interpreter, from Alexei
Starovoitov.
7) Fix arch dependencies of candence driver.
8) Fix netlink capabilities checking tree-wide, from Eric W Biederman.
9) Don't dump IFLA_VF_PORTS if netlink request didn't ask for it in
IFLA_EXT_MASK, from David Gibson.
10) IPV6 FIB dump restart doesn't handle table changes that happen
meanwhile, causing the code to loop forever or emit dups, fix from
Kumar Sandararajan.
11) Memory leak on VF removal in bnx2x, from Yuval Mintz.
12) Bug fixes for new Altera TSE driver from Vince Bridgers.
13) Fix route lookup key in SCTP, from Xugeng Zhang.
14) Use BH blocking spinlocks in SLIP, as per a similar fix to CAN/SLCAN
driver. From Oliver Hartkopp.
15) TCP doesn't bump retransmit counters in some code paths, fix from
Eric Dumazet.
16) Clamp delayed_ack in tcp_cubic to prevent theoretical divides by
zero. Fix from Liu Yu.
17) Fix locking imbalance in error paths of HHF packet scheduler, from
John Fastabend.
18) Properly reference the transport module when vsock_core_init() runs,
from Andy King.
19) Fix buffer overflow in cdc_ncm driver, from Bjørn Mork.
20) IP_ECN_decapsulate() doesn't see a correct SKB network header in
ip_tunnel_rcv(), fix from Ying Cai.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (132 commits)
net: macb: Fix race between HW and driver
net: macb: Remove 'unlikely' optimization
net: macb: Re-enable RX interrupt only when RX is done
net: macb: Clear interrupt flags
net: macb: Pass same size to DMA_UNMAP as used for DMA_MAP
ip_tunnel: Set network header properly for IP_ECN_decapsulate()
e1000e: Restrict MDIO Slow Mode workaround to relevant parts
e1000e: Fix issue with link flap on 82579
e1000e: Expand workaround for 10Mb HD throughput bug
e1000e: Workaround for dropped packets in Gig/100 speeds on 82579
net/mlx4_core: Don't issue PCIe speed/width checks for VFs
net/mlx4_core: Load the Eth driver first
net/mlx4_core: Fix slave id computation for single port VF
net/mlx4_core: Adjust port number in qp_attach wrapper when detaching
net: cdc_ncm: fix buffer overflow
Altera TSE: ALTERA_TSE should depend on HAS_DMA
vsock: Make transport the proto owner
net: sched: lock imbalance in hhf qdisc
net: mvmdio: Check for a valid interrupt instead of an error
net phy: Check for aneg completion before setting state to PHY_RUNNING
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small fixes and device ids for 3.15-rc4.
All have been in linux-next just fine"
* tag 'usb-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: Nokia 5300 should be treated as unusual dev
USB: Nokia 305 should be treated as unusual dev
fsl-usb: do not test for PHY_CLK_VALID bit on controller version 1.6
usb: storage: shuttle_usbat: fix discs being detected twice
usb: qcserial: add a number of Dell devices
USB: OHCI: fix problem with global suspend on ATI controllers
usb: gadget: at91-udc: fix irq and iomem resource retrieval
usb: phy: fsm: change "|" to "||" for condition OTG_STATE_A_WAIT_BCON at statemachine
usb: phy: fsm: update OTG HNP state transition
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are some tty and serial driver fixes for things reported
recently"
* tag 'tty-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Fix lockless tty buffer race
Revert "tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
drivers/tty/hvc: don't free hvc_console_setup after init
n_tty: Fix n_tty_write crash when echoing in raw mode
tty: serial: 8250_core.c Bug fix for Exar chips.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / iio fixes from Greg KH:
"Here are some small IIO driver fixes for 3.15-rc4 that resolve some
reported issues"
* tag 'staging-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio: adc: Nothing in ADC should be a bool CONFIG
iio: exynos_adc: use indio_dev->dev structure to handle child nodes
iio:imu:mpu6050: Fixed segfault in Invensens MPU driver due to null dereference
staging:iio:ad2s1200 fix missing parenthesis in a for statment.
|
|
Under "heavy" RX load, the driver cannot handle the descriptors fast
enough. In detail, when a descriptor is consumed, its used flag is
cleared and once the RX budget is consumed all descriptors with a
cleared used flag are prepared to receive more data. Under load though,
the HW may constantly receive more data and use those descriptors with a
cleared used flag before they are actually prepared for next usage.
The head and tail pointers into the RX-ring should always be valid and
we can omit clearing and checking of the used flag.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coverage data suggests that the unlikely case of receiving data while
the receive handler is running may not be that unlikely.
Coverage data after running iperf for a while:
91320: 891: work_done = bp->macbgem_ops.mog_rx(bp, budget);
91320: 892: if (work_done < budget) {
2362: 893: napi_complete(napi);
-: 894:
-: 895: /* Packets received while interrupts were disabled */
4724: 896: status = macb_readl(bp, RSR);
2362: 897: if (unlikely(status)) {
762: 898: if (bp->caps & MACB_CAPS_ISR_CLEAR_ON_WRITE)
762: 899: macb_writel(bp, ISR, MACB_BIT(RCOMP));
-: 900: napi_reschedule(napi);
-: 901: } else {
1600: 902: macb_writel(bp, IER, MACB_RX_INT_FLAGS);
-: 903: }
-: 904: }
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When data is received during the driver processing received data the
NAPI is re-scheduled. In that case the RX interrupt should not be
re-enabled.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few interrupt flags were not cleared in the ISR, resulting in a sytem
trapped in the ISR in cases one of those interrupts occurred. Clear all
flags to avoid such situations.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just as commit "net: macb: DMA-unmap full rx-buffer"
(48330e08fa168395b9fd9f369f06cca1df204361), pass the size that
was used for mapping the memory also to the unmap routine to
avoid warnings from the DMA_API.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates
This series contains updates to e1000e only.
David provides four fixes for e1000e, first is a workaround for a hardware
erratum on 82579 devices which experienced packet loss in gigabit and 100
speeds when interconnect between the PHY and MAC is exiting K1 power saving
state. Second expands the scope of a workaround to include i217 and i218
parts as well to address over aggressive transmit behavior when connecting
at 10Mbs half-duplex. Next is to resolve a reported link flap issue on
82579 parts which was root caused as an interoperability problem between
82579 and at least some Broadcom PHYs in the Energy Efficient Ethernet wake
mechanism. Lastly, restricts the workaround of putting the PHY into MDIO
slow mode to access the PHY id to relevant parts since this issue has been
fixed on the newer hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It has been determined that the workaround of putting the PHY into MDIO
slow mode to access the PHY id is not necessary with Lynx Point and newer
parts. The issue that necessitated the workaround has been fixed on the
newer hardware.
We will maintains, as a last ditch attempt, the conversion to MDIO Slow
Mode in the failure branch when attempting to access the PHY id so as to
cover all contingencies.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Several customers have reported a link flap issue on 82579. The symptoms
are random and intermittent link losses when 82579 is connected to specific
link partners. Issue has been root caused as interoperability problem
between 82579 and at least some Broadcom PHYs in the Energy Efficient
Ethernet wake mechanism.
To fix the issue, we are disabling the Phase Locked Loop shutdown in 100M
Low Power Idle. This solution will cause an increase of power in 100M EEE
link. It will cost additional 28mW in this specific mode.
Cc: Lukasz Adamczuk <lukasz.adamczuk@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In commit 772d05c51c4f4896c120ad418b1e91144a2ac813 "e1000e: slow performance
between two 82579 connected via 10Mbit hub", a workaround was put into place
to address the overaggressive transmit behavior of 82579 parts when connecting
at 10Mbs half-duplex.
This same behavior is seen on i217 and i218 parts as well. This patch expands
the original workaround to encompass these parts.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This is a workaround for a HW erratum on 82579 devices.
Erratum is #23 in Intel 6 Series Chipset and Intel C200 Series Chipset
specification Update June 2013.
Problem: 82579 parts experience packet loss in Gig and 100 speeds
when interconnect between PHY and MAC is exiting K1 power saving state.
This was previously believed to only affect 1Gig speed, but has been observed
at 100Mbs also.
Workaround: Disable K1 for 82579 devices at Gig and 100 speeds.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Carrying out PCI speed/width checks through pcie_get_minimum_link()
on VFs yield wrong results, so remove them.
Fixes: b912b2f ('net/mlx4_core: Warn if device doesn't have enough PCI bandwidth')
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in SRIOV mode, VM that is assigned with a non-provisioned
Ethernet VFs get themselves a random mac when the Eth driver starts. In
this case, if the IB driver startup code that deals with RoCE runs first,
it will use a zero mac as the source mac for the Para-Virtual CM MADs
which is buggy. To handle that, we change the order of loading.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The code that deals with computing the slave id based on a given GID
gave wrong results when the number of single port VFs wasn't the
same for port 1 vs. port 2 and the relevant VF is single ported on
port 2. As a result, incoming CM MADs were dispatched to the wrong VF.
Fixed that and added documentation to clarify the computation steps.
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using single ported VFs and the VF is using port 2, we need
to adjust the port accordingly (change it from 1 to 2).
Fixes: 449fc48 ('net/mlx4: Adapt code for N-Port VF')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs
if we send ZLPs") changed the padding logic for devices with the ZLP
flag set. This meant that frames of any size will be sent without
additional padding, except for the single byte added if the size is
a multiple of the USB packet size. But if the unpadded size is
identical to the maximum frame size, and the maximum size is a
multiplum of the USB packet size, then this one-byte padding will
overflow the buffer.
Prevent padding if already at maximum frame size, letting usbnet
transmit a ZLP instead in this case.
Fixes: 4d619f625a60 ("net: cdc_ncm: no point in filling up the NTBs if we send ZLPs")
Reported by: Yu-an Shih <yshih@nvidia.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If NO_DMA=y:
drivers/built-in.o: In function `altera_tse_probe':
altera_tse_main.c:(.text+0x25ec2e): undefined reference to `dma_set_mask'
altera_tse_main.c:(.text+0x25ec78): undefined reference to `dma_supported'
altera_tse_main.c:(.text+0x25ecb6): undefined reference to `dma_supported'
drivers/built-in.o: In function `sgdma_async_read':
altera_sgdma.c:(.text+0x25f620): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f678): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_uninitialize':
(.text+0x25f696): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f6f0): undefined reference to `dma_map_single'
drivers/built-in.o: In function `sgdma_initialize':
(.text+0x25f702): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `sgdma_tx_buffer':
(.text+0x25f92a): undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `sgdma_rx_status':
(.text+0x25fa24): undefined reference to `dma_sync_single_for_cpu'
make[3]: *** [vmlinux] Error 1
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless
John W. Linville says:
====================
pull request: wireless 2014-05-01
Please pull the following batch of fixes intended for the 3.15 stream!
For the Bluetooth bits, Gustavo says:
"Some fixes for 3.15. There is a revert for the intel driver, a new
device id, and two important SSP fixes from Johan."
On top of that...
Ben Hutchings gives us a fix for an unbalanced irq enable in an
rtl8192cu error path.
Colin Ian King provides an rtlwifi fix for an uninitialized variable.
Felix Fietkau brings a pair of ath9k fixes, one that corrects a
hardware initialization value and another that removes an (unnecessary)
flag that was being used in a way that led to a software tx queue
hang in ath9k.
Gertjan van Wingerde pushes a MAINTAINERS change to remove himself
from the rt2x00 maintainer team.
Hans de Goede fixes a brcmfmac firmware load hang.
Larry Finger changes rtlwifi to use the correct queue for V0 traffic
on rtl8192se.
Rajkumar Manoharan corrects a race in ath9k driver initialization.
Stanislaw Gruszka fixes an rt2x00 bug in which disabling beaconing
once on USB devices led to permanently disabling beaconing for those
devices.
Tim Harvey provides fixes for a pair of ath9k issues that can lead
to soft lockups in that driver.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ubifs fixes from Artem Bityutskiy:
"This includes the following fixes:
- two real bug-fixes from Tanya for the still "experimental" UBI
fastmap feature
- a one-liner from Kees which hardens kernel security
- a small error-path fix, where we forget to free various resources
in case of failure - spotted by the 'smatch' tool"
* tag 'upstream-3.15-rc5' of git://git.infradead.org/linux-ubifs:
UBI: avoid workqueue format string leak
UBI: fix ubi free PEBs count calculation
UBI: fix error path in __wl_get_peb
UBIFS: fix remount error path
|
|
Do not leak kernel-only floppy_raw_cmd structure members to userspace.
This includes the linked-list pointer and the pointer to the allocated
DMA space.
Signed-off-by: Matthew Daley <mattd@bugfuzz.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Always clear out these floppy_raw_cmd struct members after copying the
entire structure from userspace so that the in-kernel version is always
valid and never left in an interdeterminate state.
Signed-off-by: Matthew Daley <mattd@bugfuzz.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When building the name for the workqueue thread, make sure a format
string cannot leak in from the disk name.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The ubi->free_count should be updated with every insert/remove to/from
the ubi->free list.
Signed-off-by: Tanya Brokhman <tlinder@codeaurora.org>
Reviewed-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
In case of an error (if there are not free PEB's for example),
__wl_get_peb will return a negative value. In order to prevent access
violation we need to test the returned value prior to using it later on.
Signed-off-by: Tatyana Brokhman <tlinder@codeaurora.org>
Reviewed-by: Dolev Raviv <draviv@codeaurora.org>
Acked-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
"These are mostly arm64 fixes with an additional arm(64) platform fix
for the initialisation of vexpress clocks (the latter only affecting
arm64; the arch/arm64 code is SoC agnostic and does not rely on early
SoC-specific calls)
- vexpress platform clocks initialisation moved earlier following the
arm64 move of of_clk_init() call in a previous commit
- Default DMA ops changed to non-coherent to preserve compatibility
with 32-bit ARM DT files. The "dma-coherent" property can be used
to explicitly mark a device coherent. The Applied Micro DT file
has been updated to avoid DMA cache maintenance for the X-Gene SATA
controller (the only arm64 related driver with such assumption in
-rc mainline)
- Fixmap correction for earlyprintk
- kern_addr_valid() fix for huge pages"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
vexpress: Initialise the sysregs before setting up the clocks
arm64: Mark the Applied Micro X-Gene SATA controller as DMA coherent
arm64: Use bus notifiers to set per-device coherent DMA ops
arm64: Make default dma_ops to be noncoherent
arm64: fixmap: fix missing sub-page offset for earlyprintk
arm64: Fix for the arm64 kern_addr_valid() function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is two patches both fixing bugs in drivers (virtio-scsi and
mpt2sas) causing an oops in certain circumstances"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] virtio-scsi: Skip setting affinity on uninitialized vq
[SCSI] mpt2sas: Don't disable device twice at suspend.
|
|
Following arm64 commit bc3ee18a7a57 (arm64: init: Move of_clk_init to
time_init()), vexpress_osc_of_setup() is called via of_clk_init() long
before initcalls are issued. Initialising the vexpress oscillators
requires the vespress sysregs to be already initialised, so this patch
adds an explicit call to vexpress_sysreg_of_early_init() in vexpress
oscillator setup function.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Pawel Moll <pawel.moll@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Cc: Mike Turquette <mturquette@linaro.org>
|
|
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Victor A. Santos <victoraur.santos@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 6a20dbd6caa2358716136144bf524331d70b1e03,
"tty: Fix race condition between __tty_buffer_request_room and flush_to_ldisc"
correctly identifies an unsafe race condition between
__tty_buffer_request_room() and flush_to_ldisc(), where the consumer
flush_to_ldisc() prematurely advances the head before consuming the
last of the data committed. For example:
CPU 0 | CPU 1
__tty_buffer_request_room | flush_to_ldisc
... | ...
| count = head->commit - head->read
n = tty_buffer_alloc() |
b->commit = b->used |
b->next = n |
| if (!count) /* T */
| if (head->next == NULL) /* F */
| buf->head = head->next
In this case, buf->head has been advanced but head->commit may have
been updated with a new value.
Instead of reintroducing an unnecessary lock, fix the race locklessly.
Read the commit-next pair in the reverse order of writing, which guarantees
the commit value read is the latest value written if the head is
advancing.
Reported-by: Manfred Schlaegl <manfred.schlaegl@gmx.at>
Cc: <stable@vger.kernel.org> # 3.12.x+
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
flush_to_ldisc"
This reverts commit 6a20dbd6caa2358716136144bf524331d70b1e03.
Although the commit correctly identifies an unsafe race condition
between __tty_buffer_request_room() and flush_to_ldisc(), the commit
fixes the race with an unnecessary spinlock in a lockless algorithm.
The follow-on commit, "tty: Fix lockless tty buffer race" fixes
the race locklessly.
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When 'console=hvc0' is specified to the kernel parameter in x86 KVM guest,
hvc console is setup within a kthread. However, that will cause SEGV
and the boot will fail when the driver is builtin to the kernel,
because currently hvc_console_setup() is annotated with '__init'. This
patch removes '__init' to boot the guest successfully with 'console=hvc0'.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tty atomic_write_lock does not provide an exclusion guarantee for
the tty driver if the termios settings are LECHO & !OPOST. And since
it is unexpected and not allowed to call TTY buffer helpers like
tty_insert_flip_string concurrently, this may lead to crashes when
concurrect writers call pty_write. In that case the following two
writers:
* the ECHOing from a workqueue and
* pty_write from the process
race and can overflow the corresponding TTY buffer like follows.
If we look into tty_insert_flip_string_fixed_flag, there is:
int space = __tty_buffer_request_room(port, goal, flags);
struct tty_buffer *tb = port->buf.tail;
...
memcpy(char_buf_ptr(tb, tb->used), chars, space);
...
tb->used += space;
so the race of the two can result in something like this:
A B
__tty_buffer_request_room
__tty_buffer_request_room
memcpy(buf(tb->used), ...)
tb->used += space;
memcpy(buf(tb->used), ...) ->BOOM
B's memcpy is past the tty_buffer due to the previous A's tb->used
increment.
Since the N_TTY line discipline input processing can output
concurrently with a tty write, obtain the N_TTY ldisc output_lock to
serialize echo output with normal tty writes. This ensures the tty
buffer helper tty_insert_flip_string is not called concurrently and
everything is fine.
Note that this is nicely reproducible by an ordinary user using
forkpty and some setup around that (raw termios + ECHO). And it is
present in kernels at least after commit
d945cb9cce20ac7143c2de8d88b187f62db99bdc (pty: Rework the pty layer to
use the normal buffering logic) in 2.6.31-rc3.
js: add more info to the commit log
js: switch to bool
js: lock unconditionally
js: lock only the tty->ops->write call
References: CVE-2014-0196
Reported-and-tested-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sleep function was updated to put the serial port to sleep only when necessary.
This appears to resolve the errant behavior of the driver as described in
Kernel Bug 61961 – "My Exar Corp. XR17C/D152 Dual PCI UART modem does not
work with 3.8.0".
Signed-off-by: Michael Welling <mwelling@ieee.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Per reference manuals of Freescale P1020 and P2020 SoCs, USB controller
present in these SoCs has bit 17 of USBx_CONTROL register marked as
Reserved - there is no PHY_CLK_VALID bit there.
Testing for this bit in ehci_fsl_setup_phy() behaves differently on two
P1020RDB boards available here - on one board test passes and fsl-usb
init succeeds, but on other board test fails, causing fsl-usb init to
fail.
This patch changes ehci_fsl_setup_phy() not to test PHY_CLK_VALID on
controller version 1.6 that (per manual) does not have this bit.
Signed-off-by: Nikita Yushchenko <nyushchenko@dev.rtsoft.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even if the USB-to-ATAPI converter supported multiple LUNs, this
driver would always detect the same physical device or media because
it doesn't use srb->device->lun in any way.
Tested with an Hewlett-Packard CD-Writer Plus 8200e.
Signed-off-by: Daniele Forsi <dforsi@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Dan writes:
"The Dell drivers use the same configuration for PIDs:
81A2: Dell Wireless 5806 Gobi(TM) 4G LTE Mobile Broadband Card
81A3: Dell Wireless 5570 HSPA+ (42Mbps) Mobile Broadband Card
81A4: Dell Wireless 5570e HSPA+ (42Mbps) Mobile Broadband Card
81A8: Dell Wireless 5808 Gobi(TM) 4G LTE Mobile Broadband Card
81A9: Dell Wireless 5808e Gobi(TM) 4G LTE Mobile Broadband Card
These devices are all clearly Sierra devices, but are also definitely
Gobi-based. The A8 might be the MC7700/7710 and A9 is likely a MC7750.
>From DellGobi5kSetup.exe from the Dell drivers:
usbif0: serial/firmware loader?
usbif2: nmea
usbif3: modem/ppp
usbif8: net/QMI"
Cc: <stable@vger.kernel.org>
Reported-by: AceLan Kao <acelan.kao@canonical.com>
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some OHCI controllers from ATI/AMD seem to have difficulty with
"global" USB suspend, that is, suspending an entire USB bus without
setting the suspend feature for each port connected to a device. When
we try to resume the child devices, the controller gives timeout
errors on the unsuspended ports, requiring resets, and can even cause
ohci-hcd to hang; see
http://marc.info/?l=linux-usb&m=139514332820398&w=2
and the following messages.
This patch fixes the problem by adding a new quirk flag to ohci-hcd.
The flag causes the ohci_rh_suspend() routine to suspend each
unsuspended, enabled port before suspending the root hub. This
effectively converts the "global" suspend to an ordinary root-hub
suspend. There is no need to unsuspend these ports when the root hub
is resumed, because the child devices will be resumed anyway in the
course of a normal system resume ("global" suspend is never used for
runtime PM).
This patch should be applied to all stable kernels which include
commit 0aa2832dd0d9 (USB: use "global suspend" for system sleep on
USB-2 buses) or a backported version thereof.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Peter Münster <pmlists@free.fr>
Tested-by: Peter Münster <pmlists@free.fr>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"This udpate delivers:
- A fix for dynamic interrupt allocation on x86 which is required to
exclude the GSI interrupts from the dynamic allocatable range.
This was detected with the newfangled tablet SoCs which have GPIOs
and therefor allocate a range of interrupts. The MSI allocations
already excluded the GSI range, so we never noticed before.
- The last missing set_irq_affinity() repair, which was delayed due
to testing issues
- A few bug fixes for the armada SoC interrupt controller
- A memory allocation fix for the TI crossbar interrupt controller
- A trivial kernel-doc warning fix"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip: irq-crossbar: Not allocating enough memory
irqchip: armanda: Sanitize set_irq_affinity()
genirq: x86: Ensure that dynamic irq allocation does not conflict
linux/interrupt.h: fix new kernel-doc warnings
irqchip: armada-370-xp: Fix releasing of MSIs
irqchip: armada-370-xp: implement the ->check_device() msi_chip operation
irqchip: armada-370-xp: fix invalid cast of signed value into unsigned variable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"This update brings along:
- Two fixes for long standing bugs in the hrtimer code, one which
prevents remote enqueuing and the other preventing arbitrary delays
after a interrupt hang was detected
- A fix in the timer wheel which prevents math overflow
- A fix for a long standing issue with the architected ARM timer
related to the C3STOP mechanism.
- A trivial compile fix for nspire SoC clocksource"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timer: Prevent overflow in apply_slack
hrtimer: Prevent remote enqueue of leftmost timers
hrtimer: Prevent all reprogramming if hang detected
clocksource: nspire: Fix compiler warning
clocksource: arch_arm_timer: Fix age-old arch timer C3STOP detection issue
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"A bunch of regression fixes this time. They fix two regressions in
the PNP subsystem, one in the ACPI processor driver and one in the
ACPI EC driver, four cpufreq driver regressions and an unrelated bug
in one of the drivers. The regressions are recent or introduced in
3.14.
Specifics:
- There are two bugs in the ACPI PNP core that cause errors to be
returned if optional ACPI methods are not present. After an ACPI
core change made in 3.14 one of those errors leads to serial port
suspend failures on some systems. Fix from Rafael J Wysocki.
- A recently added PNP quirk related to Intel chipsets intorduced a
build error in unusual configurations (PNP without PCI). Fix from
Bjorn Helgaas.
- An ACPI EC workaround related to system suspend on Samsung machines
added in 3.14 introduced a race causing some valid EC events to be
discarded. Fix from Kieran Clancy.
- The acpi-cpufreq driver fails to load on some systems after a 3.14
commit related to APIC ID parsing that overlooked one corner case.
Fix from Lan Tianyu.
- Fix for a recently introduced build problem in the ppc-corenet
cpufreq driver from Tim Gardner.
- A recent cpufreq core change to ensure serialization of frequency
transitions for drivers with a ->target_index() callback overlooked
the fact that some of those drivers had been doing operations
introduced by it into the core already by themselves. That
resulted in a mess in which the core and the drivers try to do the
same thing and block each other which leads to deadlocks. Fixes
for the powernow-k7, powernow-k6, and longhaul cpufreq drivers from
Srivatsa S Bhat.
- Fix for a computational error in the powernow-k6 cpufreq driver
from Srivatsa S Bhat"
* tag 'pm+acpi-3.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / processor: Fix failure of loading acpi-cpufreq driver
PNP / ACPI: Do not return errors if _DIS or _SRS are not present
PNP: Fix compile error in quirks.c
ACPI / EC: Process rather than discard events in acpi_ec_clear
cpufreq: ppc-corenet-cpufreq: Fix __udivdi3 modpost error
cpufreq: powernow-k7: Fix double invocation of cpufreq_freq_transition_begin/end
cpufreq: powernow-k6: Fix double invocation of cpufreq_freq_transition_begin/end
cpufreq: powernow-k6: Fix incorrect comparison with max_multipler
cpufreq: longhaul: Fix double invocation of cpufreq_freq_transition_begin/end
|
|
Pull driver core deferred probe fix from Grant Likely:
"Drivercore race condition fix (exposed by devicetree)
This branch fixes a bug where a device can get stuck in the deferred
list even though all its dependencies are met. The bug has existed
for a long time, but new platform conversions to device tree have
exposed it. This patch is needed to get those platforms working.
This was the pending bug fix I mentioned in my previous pull request.
Normally this would go through Greg's tree seeing that it is a
drivercore change, but devicetree exposes the problem. I've discussed
with Greg and he okayed me asking you to pull directly"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux:
drivercore: deferral race condition fix
|
|
* acpi-ec:
ACPI / EC: Process rather than discard events in acpi_ec_clear
* acpi-processor:
ACPI / processor: Fix failure of loading acpi-cpufreq driver
|
|
* pnp:
PNP / ACPI: Do not return errors if _DIS or _SRS are not present
PNP: Fix compile error in quirks.c
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"A few dm-thinp fixes for changes merged in 3.15-rc1.
A dm-verity fix for an immutable biovec regression that affects 3.14+.
A dm-cache fix to properly quiesce when using writethrough mode (3.14+)"
* tag 'dm-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix writethrough mode quiescing in cache_map
dm thin: use INIT_WORK_ONSTACK in noflush_work to avoid ODEBUG warning
dm verity: fix biovecs hash calculation regression
dm thin: fix rcu_read_lock being held in code that can sleep
dm thin: irqsave must always be used with the pool->lock spinlock
|
|
The following commit:
commit 9ec36cafe43bf835f8f29273597a5b0cbc8267ef
Author: Rob Herring <robh@kernel.org>
Date: Wed Apr 23 17:57:41 2014 -0500
of/irq: do irq resolution in platform_get_irq
changed platform_get_irq() which now returns EINVAL and EPROBE_DEFER,
in addition to ENXIO. If there's no interrupt for mvmdio, platform_get_irq()
returns EINVAL, but we currently check only for ENXIO.
Fix this by looking for a positive integer, which is the proper way of
validating a virtual interrupt number.
While at it, add a proper handling for the deferral probe case.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_state_machine should check whether auto-negotiatin is completed
before changing phydev->state from PHY_NOLINK to PHY_RUNNING. If
auto-negotiation is not completed phydev->state should be set to
PHY_AN.
Signed-off-by: Balakumaran Kannan <kumaran.4353@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
