Age | Commit message (Collapse) | Author |
|
The nps_enet driver happily mixes virtual, physical and __iomem
addresses, which are all different depending on the architecture
and configuration. That causes a warning when building the code
on ARM with LPAE mode enabled:
drivers/net/ethernet/ezchip/nps_enet.c: In function 'nps_enet_send_frame':
drivers/net/ethernet/ezchip/nps_enet.c:370:13: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
but will also fail to work for other reasons.
In this patch, I'm trying to change the code to use only normal
kernel pointers, which I assume is what the author actually meant:
* For reading or writing a 32-bit word that may be unaligned when
an SKB contains unaligned data, I'm using get_unaligned/put_unaligned()
rather than memcpy_fromio/toio.
* For converting a u8 pointer to a u32 pointer, I use a cast rather
than the incorrect virt_to_phys.
* For copying a couple of bytes from one place to another while respecting
alignment, I use memcpy instead of memcpy_toio.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The pq_mdio driver can now be built for ARM64, where we get a format
string warning:
drivers/net/ethernet/freescale/fsl_pq_mdio.c: In function 'fsl_pq_mdio_probe':
drivers/net/ethernet/freescale/fsl_pq_mdio.c:467:25: warning: format '%x' expects argument of type 'unsigned int', but argument 3 has type 'long int' [-Wformat=]
The argument is an implicit ptrdiff_t from the subtraction of two pointers,
so we should use the %z format string modifier to make this work on 64-bit
architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: fe761bcb9046 ("net: fsl: expands dependencies of NET_VENDOR_FREESCALE")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an interface is brought up which was previously suspended (via
runtime PM), it would hang. This happens because napi_disable is called
before napi_enable.
Solve this by avoiding napi_enable in the resume during open function
(netif_running is true when open is called, IFF_UP is set after a
successful open; netif_running is false when close is called, but IFF_UP
is then still set).
While at it, remove WORK_ENABLE check from rtl8152_open (introduced with
the original change) because it cannot happen:
- After this patch, runtime resume will not set it during rtl8152_open.
- When link is up, rtl8152_open is not called.
- When link is down during system/auto suspend/resume, it is not set.
Fixes: 41cec84cf285 ("r8152: don't enable napi before rx ready")
Link: https://lkml.kernel.org/r/20151205105912.GA1766@al
Signed-off-by: Peter Wu <peter@lekensteyn.nl>
Acked-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit bc69fdfc6c13
("net: thunderx: Enable BGX LMAC's RX/TX only after VF is up")
introduces lmac_cnt member and starts verifying VF number against it.
This is plain wrong, and works only because currently we have hardcoded
1:1 mapping between VFs and LMACs, and in this case num_vf_en and
lmac_cnt are always equal. However in future this may change, and the
code will badly misbehave. The worst consequence of this is failure to
deliver link status messages, causing VFs to go defunct because since
commit 0b72a9a1060e ("net: thunderx: Switchon carrier only upon
interface link up") VF will not fully bring itself up without it.
This patch fixes the potential problem by doing VF number checks against
the num_vf_en. Since lmac_cnt is not used anywhere else, it is removed.
Additionally some duplicated code is factored out into nic_enable_vf()
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call to iptunnel_xmit_stats() is not required after udp-tunnel6-xmit.
By calling iptunnel_xmit_stats() results in incorrect device stats.
Following patch drops this call.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When looking for outer IP header, use the actual socket address family, not
the address family of the default destination which is not set for metadata
based interfaces (and doesn't have to match the address family of the
received packet even if it was set).
Fix also the misleading comment.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fill the metadata correctly even when tunneling over IPv6. Also, check that
the provided metadata is of an address family that is supported by the
tunnel.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Will be used also for ndo_fill_metadata_dst.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using INTa, ISR might be called before device is configured
for INTa [E.g., due to other device asserting the shared interrupt line],
in which case the ISR would read the SISR registers that shouldn't be
read unless HW is already configured for INTa. This might break interrupts
later on. There's also an MSI-X issue due to this difference, although
it's mostly theoretical.
This patch changes the initialization order, calling request_irq() for the
slowpath interrupt only after the chip is configured for working
in the preferred interrupt mode.
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Can't rely on pci config space to discover bar size,
as in some environments this returns a wrong, too large value.
Instead, rely on device register, which contains the value
provided by MFW at preboot.
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Concurrent non-blocking slowpath ramrods can be completed
out-of-order on the completion chain. Recycling completed elements,
while previously sent elements are still completion pending,
can lead to overriding of active elements on the chain. Furthermore,
sending pending slowpath ramrods currently lacks the update of the
chain element physical pointer.
This patch:
* Ensures that ramrods are sent to the FW with
consecutive echo values.
* Handles out-of-order completions by freeing only first
successive completed entries.
* Updates the chain element physical pointer when copying
a pending element into a free element for sending.
Signed-off-by: Tomer Tayar <Tomer.Tayar@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If NO_DMA=y:
ERROR: "dma_map_single" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
ERROR: "dma_unmap_page" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
ERROR: "dma_sync_single_for_cpu" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
ERROR: "dma_unmap_single" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
ERROR: "dma_alloc_coherent" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
ERROR: "dma_mapping_error" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
ERROR: "dma_map_page" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
ERROR: "dma_free_coherent" [drivers/net/ethernet/aurora/nb8800.ko] undefined!
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of a tx queue timeout every transmit is blocked until the
QCA7000 resets himself and triggers a sync which makes the driver
flushs the tx ring. So avoid this blocking situation by triggering
the sync immediately after the timeout. Waking the queue doesn't
make sense in this situation.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06ecf67 ("net: qualcomm: new Ethernet over SPI driver for QCA7000")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Huawei E3372 (12d1:157d) needs this quirk in MBIM mode
as well. Allow this by forcing the NTB to contain only a
single NDP, and add a device specific entry for this ID.
Due to the way Huawei use device IDs, this might be applied
to other modems as well. It is assumed that those modems
will be based on the same firmware and will need this quirk
too. If not, it will still not harm normal usage, although
multiplexing performance could be impacted.
Cc: Enrico Mioso <mrkiko.rs@gmail.com>
Reported-by: Sami Farin <hvtaifwkbgefbaei@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-By: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a memleak when suspend/resume this driver version.
Currently the stmmac, during resume step, reallocates all the resources
but they are not released when suspend.
The patch is not to release these resources but the logic has been changed.
In fact, it is not necessary to free and reallocate all from scratch
because the memory data will be always preserved.
As final solution, the patch just reinit the descriptors and the rx/tx
pointers only when resume. Tested done on STi boxes.
Reported-by: ZhengShunQian <zhengsq@rock-chips.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Rx queue #1 frame error counter name contains trailing underscore,
probably due to a typo...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a low memory situation the following kernel oops occurs:
Unable to handle kernel NULL pointer dereference at virtual address 00000050
pgd = 8490c000
[00000050] *pgd=4651e831, *pte=00000000, *ppte=00000000
Internal error: Oops: 17 [#1] PREEMPT ARM
Modules linked in:
CPU: 0 Not tainted (3.4-at16 #9)
PC is at skb_put+0x10/0x98
LR is at sh_eth_poll+0x2c8/0xa10
pc : [<8035f780>] lr : [<8028bf50>] psr: 60000113
sp : 84eb1a90 ip : 84eb1ac8 fp : 84eb1ac4
r10: 0000003f r9 : 000005ea r8 : 00000000
r7 : 00000000 r6 : 940453b0 r5 : 00030000 r4 : 9381b180
r3 : 00000000 r2 : 00000000 r1 : 000005ea r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c53c7d Table: 4248c059 DAC: 00000015
Process klogd (pid: 2046, stack limit = 0x84eb02e8)
[...]
This is because netdev_alloc_skb() fails and 'mdp->rx_skbuff[entry]' is left
NULL but sh_eth_rx() later uses it without checking. Add such check...
Reported-by: Yasushi SHOJI <yashi@atmark-techno.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2015-12-03
This series contains updates to ixgbe, i40e/i40evf, MAINTAINERS and e100.txt
Alex provides a fix for ixgbe where enabling SR-IOV and then bringing the
interface up was resulting in the PF MAC addresses getting into a bad state.
The workaround for this issue is to bring up the interface first and then
enable SR-IOV as this will trigger the reset in the existing code.
I clean up legacy license stuff in the e100.txt documentation and then
update the maintainers/reviewers list for our drivers.
Jesse fixes an issue with the i40e/i40evf drivers, where if the driver were
to happen to have a mutex held while the i40e_init_adminq() call was called,
the init_adminq might inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
atl1c driver is doing order-4 allocation with GFP_ATOMIC
priority. That often breaks networking after resume. Switch to
GFP_KERNEL. Still not ideal, but should be significantly better.
atl1c_setup_ring_resources() is called from .open() function, and
already uses GFP_KERNEL, so this change is safe.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pppoe_connect() mustn't touch the padt_work field of pppoe sockets
because that work could be already pending.
[ 21.473147] BUG: unable to handle kernel NULL pointer dereference at 00000004
[ 21.474523] IP: [<c1043177>] process_one_work+0x29/0x31c
[ 21.475164] *pde = 00000000
[ 21.475513] Oops: 0000 [#1] SMP
[ 21.475910] Modules linked in: pppoe pppox ppp_generic slhc crc32c_intel aesni_intel virtio_net xts aes_i586 lrw gf128mul ablk_helper cryptd evdev acpi_cpufreq processor serio_raw button ext4 crc16 mbcache jbd2 virtio_blk virtio_pci virtio_ring virtio
[ 21.476168] CPU: 2 PID: 164 Comm: kworker/2:2 Not tainted 4.4.0-rc1 #1
[ 21.476168] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Debian-1.8.2-1 04/01/2014
[ 21.476168] task: f5f83c00 ti: f5e28000 task.ti: f5e28000
[ 21.476168] EIP: 0060:[<c1043177>] EFLAGS: 00010046 CPU: 2
[ 21.476168] EIP is at process_one_work+0x29/0x31c
[ 21.484082] EAX: 00000000 EBX: f678b2a0 ECX: 00000004 EDX: 00000000
[ 21.484082] ESI: f6c69940 EDI: f5e29ef0 EBP: f5e29f0c ESP: f5e29edc
[ 21.484082] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 21.484082] CR0: 80050033 CR2: 000000a4 CR3: 317ad000 CR4: 00040690
[ 21.484082] Stack:
[ 21.484082] 00000000 f6c69950 00000000 f6c69940 c0042338 f5e29f0c c1327945 00000000
[ 21.484082] 00000008 f678b2a0 f6c69940 f678b2b8 f5e29f30 c1043984 f5f83c00 f6c69970
[ 21.484082] f678b2a0 c10437d3 f6775e80 f678b2a0 c10437d3 f5e29fac c1047059 f5e29f74
[ 21.484082] Call Trace:
[ 21.484082] [<c1327945>] ? _raw_spin_lock_irq+0x28/0x30
[ 21.484082] [<c1043984>] worker_thread+0x1b1/0x244
[ 21.484082] [<c10437d3>] ? rescuer_thread+0x229/0x229
[ 21.484082] [<c10437d3>] ? rescuer_thread+0x229/0x229
[ 21.484082] [<c1047059>] kthread+0x8f/0x94
[ 21.484082] [<c1327a32>] ? _raw_spin_unlock_irq+0x22/0x26
[ 21.484082] [<c1327ee9>] ret_from_kernel_thread+0x21/0x38
[ 21.484082] [<c1046fca>] ? kthread_parkme+0x19/0x19
[ 21.496082] Code: 5d c3 55 89 e5 57 56 53 89 c3 83 ec 24 89 d0 89 55 e0 8d 7d e4 e8 6c d8 ff ff b9 04 00 00 00 89 45 d8 8b 43 24 89 45 dc 8b 45 d8 <8b> 40 04 8b 80 e0 00 00 00 c1 e8 05 24 01 88 45 d7 8b 45 e0 8d
[ 21.496082] EIP: [<c1043177>] process_one_work+0x29/0x31c SS:ESP 0068:f5e29edc
[ 21.496082] CR2: 0000000000000004
[ 21.496082] ---[ end trace e362cc9cf10dae89 ]---
Reported-by: Andrew <nitr0@seti.kr.ua>
Fixes: 287f3a943fef ("pppoe: Use workqueue to die properly when a PADT is received")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In hitherto code in case of RX buffer allocation error during refill,
original buffer is pushed to the network stack, but the amount of
available buffer pointers in BM pool is decreased.
This commit fixes the situation by moving refill call before skb_put(),
and returning original buffer pointer to the pool in case of an error.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each allocated buffer, whose pointer is put into BM pool is DMA-mapped.
Hence it should be properly unmapped after usage or when removing buffers
from pool.
This commit fixes DMA handling on RX path by adding dma_unmap_single() in
mvpp2_rx() and in mvpp2_bufs_free(). The latter function's argument number
had to be increased for this purpose.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This condition is true only for the last fragment of the packet.
Since every descriptor's buffer is DMA-mapped it has to be properly
unmapped.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375
network unit")
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"A lot of Thanksgiving turkey leftovers accumulated, here goes:
1) Fix bluetooth l2cap_chan object leak, from Johan Hedberg.
2) IDs for some new iwlwifi chips, from Oren Givon.
3) Fix rtlwifi lockups on boot, from Larry Finger.
4) Fix memory leak in fm10k, from Stephen Hemminger.
5) We have a route leak in the ipv6 tunnel infrastructure, fix from
Paolo Abeni.
6) Fix buffer pointer handling in arm64 bpf JIT,f rom Zi Shen Lim.
7) Wrong lockdep annotations in tcp md5 support, fix from Eric
Dumazet.
8) Work around some middle boxes which prevent proper handling of TCP
Fast Open, from Yuchung Cheng.
9) TCP repair can do huge kmalloc() requests, build paged SKBs
instead. From Eric Dumazet.
10) Fix msg_controllen overflow in scm_detach_fds, from Daniel
Borkmann.
11) Fix device leaks on ipmr table destruction in ipv4 and ipv6, from
Nikolay Aleksandrov.
12) Fix use after free in epoll with AF_UNIX sockets, from Rainer
Weikusat.
13) Fix double free in VRF code, from Nikolay Aleksandrov.
14) Fix skb leaks on socket receive queue in tipc, from Ying Xue.
15) Fix ifup/ifdown crach in xgene driver, from Iyappan Subramanian.
16) Fix clearing of persistent array maps in bpf, from Daniel
Borkmann.
17) In TCP, for the cross-SYN case, we don't initialize tp->copied_seq
early enough. From Eric Dumazet.
18) Fix out of bounds accesses in bpf array implementation when
updating elements, from Daniel Borkmann.
19) Fill gaps in RCU protection of np->opt in ipv6 stack, from Eric
Dumazet.
20) When dumping proxy neigh entries, we have to accomodate NULL
device pointers properly, from Konstantin Khlebnikov.
21) SCTP doesn't release all ipv6 socket resources properly, fix from
Eric Dumazet.
22) Prevent underflows of sch->q.qlen for multiqueue packet
schedulers, also from Eric Dumazet.
23) Fix MAC and unicast list handling in bnxt_en driver, from Jeffrey
Huang and Michael Chan.
24) Don't actively scan radar channels, from Antonio Quartulli"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (110 commits)
net: phy: reset only targeted phy
bnxt_en: Setup uc_list mac filters after resetting the chip.
bnxt_en: enforce proper storing of MAC address
bnxt_en: Fixed incorrect implementation of ndo_set_mac_address
net: lpc_eth: remove irq > NR_IRQS check from probe()
net_sched: fix qdisc_tree_decrease_qlen() races
openvswitch: fix hangup on vxlan/gre/geneve device deletion
ipv4: igmp: Allow removing groups from a removed interface
ipv6: sctp: implement sctp_v6_destroy_sock()
arm64: bpf: add 'store immediate' instruction
ipv6: kill sk_dst_lock
ipv6: sctp: add rcu protection around np->opt
net/neighbour: fix crash at dumping device-agnostic proxy entries
sctp: use GFP_USER for user-controlled kmalloc
sctp: convert sack_needed and sack_generation to bits
ipv6: add complete rcu protection around np->opt
bpf: fix allocation warnings in bpf maps and integer overflow
mvebu: dts: enable IP checksum with jumbo frames for Armada 38x on Port0
net: mvneta: enable setting custom TX IP checksum limit
net: mvneta: fix error path for building skb
...
|
|
Pull block fixes from Jens Axboe:
"A collection of fixes from this series. The most important here is a
regression fix for an issue that some folks would hit in blk-merge.c,
and the NVMe queue depth limit for the screwed up Apple "nvme"
controller.
In more detail, this pull request contains:
- a set of fixes for null_blk, including a fix for a few corner cases
where we could hang the device. From Arianna and Paolo.
- lightnvm:
- A build improvement from Keith.
- Update the qemu pci id detection from Matias.
- Error handling fixes for leaks and other little fixes from
Sudip and Wenwei.
- fix from Eric where BLKRRPART would not return EBUSY for whole
device mounts, only when partitions were mounted.
- fix from Jan Kara, where EOF O_DIRECT reads would return
negatively.
- remove check for rq_mergeable() when checking limits for cloned
requests. The check doesn't make any sense. It's assuming that
since NOMERGE is set on the request that we don't have to
recalculate limits since the request didn't change, but that's not
true if the request has been redirected. From Hannes.
- correctly get the bio front segment value set for single segment
bio's, fixing a BUG() in blk-merge. From Ming"
* 'for-linus' of git://git.kernel.dk/linux-block:
nvme: temporary fix for Apple controller reset
null_blk: change type of completion_nsec to unsigned long
null_blk: guarantee device restart in all irq modes
null_blk: set a separate timer for each command
blk-merge: fix computing bio->bi_seg_front_size in case of single segment
direct-io: Fix negative return from dio read beyond eof
block: Always check queue limits for cloned requests
lightnvm: missing nvm_lock acquire
lightnvm: unconverted ppa returned in get_bb_tbl
lightnvm: refactor and change vendor id for qemu
lightnvm: do device max sectors boundary check first
lightnvm: fix ioctl memory leaks
lightnvm: free memory when gennvm register fails
lightnvm: Simplify config when disabled
Return EBUSY from BLKRRPART for mounted whole-dev fs
|
|
If the driver were to happen to have a mutex held while
the i40e_init_adminq call was called, the init_adminq might
inadvertently call mutex_init on a lock that was held
which is a violation of the calling semantics.
Fix this by avoiding adminq.c code allocating/freeing this memory, and
then do the same work only once in probe/remove.
Testing Hints (Required if no HSD): for VF, load i40evf in bare metal
and echo 32 > sriov_numvfs; echo 0 > sriov_numvfs in a loop. Yes this
is a horrible thing to do.
Change-ID: Ida263c51b34e195252179e7e5e400d73a99be7a2
Reported-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Enabling SR-IOV and then bringing the interface up was resulting in the PF
MAC addresses getting into a bad state. Specifically the MAC address was
enabled for both VF 0 and the PF. This resulted in some odd behaviors such
as VF 0 receiving a copy of the PFs traffic, which in turn enables the
ability for VF 0 to spoof the PF.
A workaround for this issue appears to be to bring up the interface first
and then enable SR-IOV as this way the reset is then triggered in the
existing code.
In order to correct this I have added a change to ixgbe_setup_tc where if
the interface is down we still will at least call ixgbe_reset so that the
MAC addresses for the device are reset to the correct pools.
Steps to reproduce issue:
modprobe ixgbe
echo 7 > /sys/bus/pci/devices/0000\:01\:00.1/sriov_numvfs
ifconfig enp1s0f1 up
ethregs -s 1:00.1 | grep MPSAR | grep -v 00000000
Result:
MPSAR[0] 00000081
MPSAR[254] 00000001
Expected Result, behavior after patch:
MPSAR[0] 00000080
MPSAR[254] 00000080
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Darin Miller <darin.j.miller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It is possible to address another chip on same MDIO bus. The case is
correctly handled for media advertising. It is taken into account
only if mii_data->phy_id == phydev->addr. However, this condition
was missing for reset case.
Signed-off-by: Jérôme Pouiller <jezz@sysmic.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call bnxt_cfg_rx_mode() in bnxt_init_chip() to setup uc_list and
mc_list mac address filters. Before the patch, uc_list is not
setup again after chip reset (such as ethtool ring size change)
and macvlans don't work any more after that.
Modify bnxt_cfg_rx_mode() to return error codes appropriately so
that the init chip sequence can detect any failures.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing ndo_set_mac_address only copies the new MAC addr
and didn't set the new MAC addr to the HW. The correct way is
to delete the existing default MAC filter from HW and add
the new one. Because of RFS filters are also dependent on the
default mac filter l2 context, the driver must go thru
close_nic() to delete the default MAC and RFS filters, then
open_nic() to set the default MAC address to HW.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the driver is used on an ARM platform with SPARSE_IRQ defined,
semantics of NR_IRQS is different (minimal value of virtual irqs) and
by default it is set to 16, see arch/arm/include/asm/irq.h.
This value may be less than the actual number of virtual irqs, which
may break the driver initialization. The check removal allows to use
the driver on such a platform, and, if irq controller driver works
correctly, the check is not needed on legacy platforms.
Fixes a runtime problem:
lpc-eth 31060000.ethernet: error getting resources.
lpc_eth: lpc-eth: not found (-6).
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since Armada 38x SoC can support IP checksum for jumbo frames only on
a single port, it means that this feature should be enabled per-port,
rather than for the whole SoC.
This patch enables setting custom TX IP checksum limit by adding new
optional property to the mvneta device tree node. If not used, by
default 1600B is set for "marvell,armada-370-neta" and 9800B for other
strings, which ensures backward compatibility. Binding documentation
is updated accordingly.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the actual RX processing, there is same error path for both descriptor
ring refilling and building skb fails. This is not correct, because after
successful refill, the ring is already updated with newly allocated
buffer. Then, in case of build_skb() fail, hitherto code left the original
buffer unmapped.
This patch fixes above situation by swapping error check of skb build with
DMA-unmap of original buffer.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: <stable@vger.kernel.org> # v4.2+
Fixes a84e32894191 ("net: mvneta: fix refilling for Rx DMA buffers")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A value originally defined in the driver was inappropriate. Even though
the ingress was somehow working, writing MVNETA_RXQ_INTR_ENABLE_ALL_MASK
to MVNETA_INTR_ENABLE didn't make any effect, because the bits [31:16]
are reserved and read-only.
This commit updates MVNETA_RXQ_INTR_ENABLE_ALL_MASK to be compliant with
the controller's documentation.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MVNETA_RXQ_HW_BUF_ALLOC bit which controls enabling hardware buffer
allocation was mistakenly set as BIT(1). This commit fixes the assignment.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds missing configuration of MBUS windows access protection
in mvneta_conf_mbus_windows function - a dedicated variable for that
purpose remained there unused since v3.8 initial mvneta support. Because
of that the register contents were inherited from the bootloader.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: c5aff18204da ("net: mvneta: driver for Marvell Armada 370/XP network
unit")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"There's one fix for the core here, we weren't reinitialising the
actual transferred length in messages when they get reused which meant
that we'd just keep adding to the length if a message is reused. This
has limited impact since it's only used in error handling cases but
will really mess anything that tries to use it up when it triggers.
As ever there's a small collection of driver specific fixes too"
* tag 'spi-fix-v4.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: bugfix: spi_message.transfer_length does not get reset
spi: pl022: handle EPROBE_DEFER for dma
spi: bcm63xx: use correct format string for printing a resource
spi: mediatek: single device does not require cs_gpios
spi: Add missing kerneldoc description for parameter
|
|
Enable or disable BGX LMAC's RX/TX based on corresponding VF's
status. If otherwise, when multiple LMAC's physical link is up
then packets from all LMAC's whose corresponding VF is not yet
initialized will get forwarded to VF0. This is due to VNIC's default
configuration where CPI, RSSI e.t.c point to VF0/QSET0/RQ0.
This patch will prevent multiple copies of packets on VF0.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call netif_carrier_on() only if interface's link is up. Switching this on
upon IFF_UP by default, is causing issues with ethernet channel bonding
in LACP mode. Initial NETDEV_CHANGE notification was being skipped.
Also fixed some issues with link/speed/duplex reporting via ethtool.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Properly set CQ timer threshold and also set it to 2us.
With previous incorrect settings it was set to 0.5us which is too less.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While VNIC or BGX driver teardown, wait for already scheduled delayed work to
finish before destroying it.
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Thanneeru Srinivasulu <tsrinivasulu@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- regression fix for hid-lg driver from Benjamin Tissoires
- quirk for Logitech G710+ from Jimmy Berry
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: lg: restrict filtering out of first interface to G29 only
HID: usbhid: add Logitech G710+ keyboard quirk NOGET
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pincontrol fixes from Linus Walleij:
"These are some v4.4 pin control fixes:
- Drop a redundant if-clause from Kconfig
- Fix a missing of_node_put() memory leak in the Freescale i.MX
driver
- Fix 64bit compilation of the Qualcomm SSBI driver.
- Fix a logic inversion in the Mediatek driver.
- Fix a compilation error for the odd one off in the Super-H instance
of the SH PFC driver"
* tag 'pinctrl-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: sh-pfc: sh7734: Add missing cfg macro parameter to fix build
pinctrl: mediatek: Add get_direction support.
pinctrl: fix qcom ssbi drivers for 64-bit compilation
pinctrl: imx1-core: add missing of_node_put
pinctrl: remove redundant if conditional from Kconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes for the v4.4 series:
- Fix a bunch of possible NULL references found by Coccinelle
jockeys.
- Stop creating Tegra's debugfs on everything and its dog. This is
an ARM multiplatform kernel issue.
- Fix an oops in gpiolib for NULL names on named GPIOs.
- Fix a complex OMAP1 bug in the OMAP driver"
* tag 'gpio-v4.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: omap: drop omap1 mpuio specific irq_mask/unmask callbacks
gpiolib: fix oops, if gpio name is NULL
gpio-tegra: Do not create the debugfs entry by default
gpio: palmas: fix a possible NULL dereference
gpio: syscon: fix a possible NULL dereference
gpio: 74xx: fix a possible NULL dereference
|
|
Looks like 29fae1c85 ("HID: logitech: Add support for G29") was a little
bit aggressive and broke other devices.
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=108121
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch is a cleanup to make following patch easier to
review.
Goal is to move SOCK_ASYNC_NOSPACE and SOCK_ASYNC_WAITDATA
from (struct socket)->flags to a (struct socket_wq)->flags
to benefit from RCU protection in sock_wake_async()
To ease backports, we rename both constants.
Two new helpers, sk_set_bit(int nr, struct sock *sk)
and sk_clear_bit(int net, struct sock *sk) are added so that
following patch can change their implementation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recent patches added basic support for the Apple NVMe controller but
still cause resets and data corruption on that particular controller
when a specific pattern of read/flush commands occurs. Limiting the
queue depth to 2 works around that issue.
This patch enforces that limit only for the Apple controller and is
considered a temporary fix until we find the root source of that
problem.
Signed-off-by: Stephan Günther <guenther@tum.de>
Signed-off-by: Maurice Leclaire <leclaire@in.tum.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
vmxnet3_drv does not check dma_addr with dma_mapping_error()
after mapping dma memory. The patch adds the checks and
tries to handle failures.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|