Age | Commit message (Collapse) | Author |
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-09-03
This series contains updates to ice driver only.
Anirudh adds the ability for the driver to handle EMP resets correctly
by adding the logic to the existing ice_reset_subtask().
Jeb fixes up the logic to properly free up the resources for a switch
rule whether or not it was successful in the removal.
Brett fixes up the reporting of ITR values to let the user know odd ITR
values are not allowed. Fixes the driver to only disable VLAN pruning
on VLAN deletion when the VLAN being deleted is the last VLAN on the VF
VSI.
Chinh updates the driver to determine the TSA value from the priority
value when in CEE mode.
Bruce aligns the driver with the hardware specification by ensuring that
a PF reset is done as part of the unload logic. Also update the driver
unloading field, based on the latest hardware specification, which
allows us to remove an unnecessary endian conversion. Moves #defines
based on their need in the code.
Jesse adds the current state of auto-negotiation in the link up message.
In addition, adds additional information to inform the user of an issue
with the topology/configuration of the link.
Usha updates the driver to allow the maximum TCs that the firmware
supports, rather than hard coding to a set value.
Dave updates the DCB initialization flow to handle the case of an actual
error during DCB init. Updated the driver to report the current stats,
even when the netdev is down, which aligns with our other drivers.
Mitch fixes the VF reset code flows to ensure that it properly calls
ice_dis_vsi_txq() to notify the firmware that the VF is being reset.
Michal fixes the driver so the DCB is not enabled when the SW LLDP is
activated, which was causing a communication issue with other NICs. The
problem lies in that DCB was being enabled without checking the number
of TCs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2019-09-01 (Software steering support)
Abstract:
--------
Mellanox ConnetX devices supports packet matching, packet modification and
redirection. These functionalities are also referred to as flow-steering.
To configure a steering rule, the rule is written to the device owned
memory, this memory is accessed and cached by the device when processing
a packet.
Steering rules are constructed from multiple steering entries (STE).
Rules are configured using the Firmware command interface. The Firmware
processes the given driver command and translates them to STEs, then
writes them to the device memory in the current steering tables.
This process is slow due to the architecture of the command interface and
the processing complexity of each rule.
The highlight of this patchset is to cut the middle man (The firmware) and
do steering rules programming into device directly from the driver, with
no firmware intervention whatsoever.
Motivation:
-----------
Software (driver managed) steering allows for high rule insertion rates
compared to the FW steering described above, this is achieved by using
internal RDMA writes to the device owned memory instead of the slow
command interface to program steering rules.
Software (driver managed) steering, doesn't depend on new FW
for new steering functionality, new implementations can be done in the
driver skipping the FW layer.
Performance:
------------
The insertion rate on a single core using the new approach allows
programming ~300K rules per sec. (Done via direct raw test to the new mlx5
sw steering layer, without any kernel layer involved).
Test: TC L2 rules
33K/s with Software steering (this patchset).
5K/s with FW and current driver.
This will improve OVS based solution performance.
Architecture and implementation details:
----------------------------------------
Software steering will be dynamically selected via devlink device
parameter. Example:
$ devlink dev param show pci/0000:06:00.0 name flow_steering_mode
pci/0000:06:00.0:
name flow_steering_mode type driver-specific
values:
cmode runtime value smfs
mlx5 software steering module a.k.a (DR - Direct Rule) is implemented
and contained in mlx5/core/steering directory and controlled by
MLX5_SW_STEERING kconfig flag.
mlx5 core steering layer (fs_core) already provides a shim layer for
implementing different steering mechanisms, software steering will
leverage that as seen at the end of this series.
When Software Steering for a specific steering domain
(NIC/RDMA/Vport/ESwitch, etc ..) is supported, it will cause rules
targeting this domain to be created using SW steering instead of FW.
The implementation includes:
Domain - The steering domain is the object that all other object resides
in. It holds the memory allocator, send engine, locks and other shared
data needed by lower objects such as table, matcher, rule, action.
Each domain can contain multiple tables. Domain is equivalent to
namespaces e.g (NIC/RDMA/Vport/ESwitch, etc ..) as implemented
currently in mlx5_core fs_core (flow steering core).
Table - Table objects are used for holding multiple matchers, each table
has a level used to prevent processing loops. Packets are being
directed to this table once it is set as the root table, this is done
by fs_core using a FW command. A packet is being processed inside the
table matcher by matcher until a successful hit, otherwise the packet
will perform the default action.
Matcher - Matchers objects are used to specify the fields mask for
matching when processing a packet. A matcher belongs to a table, each
matcher can hold multiple rules, each rule with different matching
values corresponding to the matcher mask. Each matcher has a priority
used for rule processing order inside the table.
Action - Action objects are created to specify different steering actions
such as count, reformat (encapsulate, decapsulate, ...), modify
header, forward to table and many other actions. When creating a rule
a sequence of actions can be provided to be executed on a successful
match.
Rule - Rule objects are used to specify a specific match on packets as
well as the actions that should be executed. A rule belongs to a
matcher.
STE - This layer is used to hold the specific STE format for the device
and to convert the requested rule to STEs. Each rule is constructed of
an STE chain, Multiple rules construct a steering graph. Each node in
the graph is a hash table containing multiple STEs. The index of each
STE in the hash table is being calculated using a CRC32 hash function.
Memory pool - Used for managing and caching device owned memory for rule
insertion. The memory is being allocated using DM (device memory) API.
Communication with device - layer for standard RDMA operation using RC QP
to configure the device steering.
Command utility - This module holds all of the FW commands that are
required for SW steering to function.
Patch planning and files:
-------------------------
1) First patch, adds the support to Add flow steering actions to fs_cmd
shim layer.
2) Next 12 patch will add a file per each Software steering
functionality/module as described above. (See patches with title: DR, *)
3) Add CONFIG_MLX5_SW_STEERING for software steering support and enable
build with the new files
4) Next two patches will add the support for software steering in mlx5
steering shim layer
net/mlx5: Add API to set the namespace steering mode
net/mlx5: Add direct rule fs_cmd implementation
5) Last two patches will add the new devlink parameter to select mlx5
steering mode, will be valid only for switchdev mode for now.
Two modes are supported:
1. DMFS - Device managed flow steering
2. SMFS - Software/Driver managed flow steering.
In the DMFS mode, the HW steering entities are created through the
FW. In the SMFS mode this entities are created though the driver
directly.
The driver will use the devlink steering mode only if the steering
domain supports it, for now SMFS will manages only the switchdev
eswitch steering domain.
User command examples:
- Set SMFS flow steering mode::
$ devlink dev param set pci/0000:06:00.0 name flow_steering_mode value "smfs" cmode runtime
- Read device flow steering mode::
$ devlink dev param show pci/0000:06:00.0 name flow_steering_mode
pci/0000:06:00.0:
name flow_steering_mode type driver-specific
values:
cmode runtime value smfs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently if the VF adds a VLAN, VLAN pruning will be enabled for that VSI.
Also, when a VLAN gets deleted it will disable VLAN pruning even if other
VLAN(s) exists for the VF. Fix this by only disabling VLAN pruning on the
VF VSI when removing the last VF (i.e. vf->num_vlan == 0).
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove code that enables DCB in initialization when SW LLDP is
activated. DCB flag is set or reset before in ice_init_pf_dcb
based on number of TCs. So there is not need to overwrite it.
Setting DCB without checking number of TCs can cause communication
problems with other cards. Host card sends packet with VLAN priority
tag, but client card doesn't strip this tag and ping doesn't work.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There is currently a check in get_ndo_stats that
returns before updating stats if the VSI is down
or there are no Tx or Rx queues. This causes the
netdev to report zero stats with the netdev is down.
Remove the check so that the behavior of reporting
stats is the same as it was in IXGBE.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The call to ice_dis_vsi_txq() acts as the notification to the firmware
that the VF is being reset. Because of this, we need to make this call
every time we reset, regardless of whatever else we do to stop the Tx
queues.
Without this change, VF resets would fail to complete on interfaces that
were up and running.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the init path for DCB, the call to ice_init_dcb()
can return a non-zero value for either an actual
error, or due to the FW lldp engine being stopped.
We are currently treating all non-zero values only as
an indication that the FW LLDP engine is stopped.
Check for an actual error in the DCB init flow.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch limits the max TCs set by the driver to the value provided by
the firmware as per the capabilities of the device. Otherwise, hard coding
to 8 TC max would fail the device configurations with more than 4 ports.
Signed-off-by: Usha Ketineni <usha.k.ketineni@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Conventionally, if the #defines/other are not needed by other header
files being included, #includes are done first followed by #defines
and other stuff. Move the #defines before the #includes to follow this
convention.
Suggested by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The driver needs to inform the user if there is an issue
with the topology / configuration of the link.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Print the state of auto-negotiation when printing the Link
up message. Adds new text to the "NIC Link is up" line like
Autoneg: <True | False>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to recent specification versions, the field in the Queue Shutdown
AdminQ command consisting of the "driver unloading" indication is not a 4
byte field (it is byte.bit 16.0). Change it to a byte and remove the
unnecessary endian conversion.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
According to the specification, a PF Reset must be done as part of the
driver unload flow.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In CEE mode, the TSA information can be derived from the reported
priority value.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently if the user sets an odd value for [tx|rx]-usecs we align the
value because the hardware only understands ITR values in multiples of
2. This seems misleading because we are essentially telling the user
that the ITR value is odd, when in fact we have changed it internally.
Fix this by reporting that setting odd ITR values is not allowed.
Also, while making changes to ice_set_rc_coalesce() I noticed a bit of
code/error duplication. Make the necessary changes to remove the
duplication.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We don't free s_rule if ice_aq_sw_rules() returns a non-zero status. If
it returned a zero status, s_rule would be freed right after, so this
implies it should be freed within the scope of the function regardless.
Signed-off-by: Jeb Cramer <jeb.j.cramer@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
ice_reset_subtask needs to handle EMP resets as well, as EMP resets
can be triggered by the firmware. This patch adds the logic to do
this.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add new parameter (flow_steering_mode) to control the flow steering
mode of the driver.
Two modes are supported:
1. DMFS - Device managed flow steering
2. SMFS - Software/Driver managed flow steering.
In the DMFS mode, the HW steering entities are created through the
FW. In the SMFS mode this entities are created though the driver
directly.
The driver will use the devlink steering mode only if the steering
domain supports it, for now SMFS will manages only the switchdev eswitch
steering domain.
User command examples:
- Set SMFS flow steering mode::
$ devlink dev param set pci/0000:06:00.0 name flow_steering_mode value "smfs" cmode runtime
- Read device flow steering mode::
$ devlink dev param show pci/0000:06:00.0 name flow_steering_mode
pci/0000:06:00.0:
name flow_steering_mode type driver-specific
values:
cmode runtime value smfs
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In case that flow steering mode of the driver is SMFS (Software Managed
Flow Steering), then use the DR (SW steering) API to create the steering
objects.
In addition, add a call to the set peer namespace when switchdev gets
devcom pair event. It is required to support VF LAG in SMFS.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add API to set the flow steering root namesapce mode.
Setting new mode should be called before any steering operation
is executed on the namespace.
This API is going to be used by steering users such switchdev.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support to create flow steering objects
via direct rule API (SW steering).
New layer is added - fs_dr, this layer translates the command that
fs_core sends to the FW into direct rule API. In case that direct
rule is not supported in some feature then -EOPNOTSUPP is
returned.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add new mlx5 Kconfig flag to allow selecting software steering
support and compile all the steering files only if the flag is
selected.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Expose APIs for direct rule managing to increase insertion rate by
bypassing the firmware.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
SW steering is capable of doing many steering functionalities
but there are still some functionalities which are not exposed
to upper layers and therefore performed by the FW.
This is the support for recalculating checksum using a hairpin QP.
The recalculation is required after a modify TTL action which skips
the needed CS calculation in HW.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Rules are the actual objects that tie matchers, header values and
actions. Each rule belongs to a matcher, which can hold multiple rules
sharing the same mask. Each rule is a specific set of values and
actions.
When a packet reaches a matcher it is being matched against the
matcher`s rules. In case of a match over a rule its actions will be
executed. Each rule object contains a set of STEs, where each STE is a
definition of match values and actions defined by the rule.
This file handles the rule operations and processing.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On rule creation a set of actions can be provided, the actions describe
what to do with the packet in case of a match. It is possible to provide
a set of actions which will be done by order.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Matcher defines which packets fields are matched when a packet arrives.
Matcher is a part of a table and can contain one or more rules. Where
rule defines specific values of the matcher's mask definition.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Tables are objects which are used for storing matchers, each table
belongs to a domain and defined by the domain type. When a packet
reaches the table it is being processed by each of its matchers until a
successful match. Tables can hold multiple matchers ordered by matcher
priority. Each table has a level.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Domain is the frame for all of the dr (direct rule) objects.
There are different domain types which also affect the object under that
domain. Each domain can hold multiple tables which can hold multiple
matchers and so on, this means that all of the dr (direct rule) objects
exist under a specific domain. The domain object also holds the
resources needed for other objects such as memory management and
communication with the device.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Steering Entry (STE) object is the basic building block of the steering
map. There are several types of STEs. Each rule can be constructed of
multiple STEs. Each STE dictates which fields of the packet's header are
being matched as well as the information about the next step in map (hit
and miss pointers). The hardware gets a packet and tries to match it
against the STEs, going to either the hit pointer or the miss pointer.
This file handles the STE operations.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Inserting or deleting a rule is done by RDMA read/write operation to SW
ICM device memory. This file provides the support for executing these
operations. It includes allocating the needed resources and providing an
API for writing steering entries to the memory.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Mark Bloch <markb@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
ICM device memory is used for writing steering rules (STEs) to the NIC.
An ICM memory pool allocator was implemented to manage the required
memory. The pool consists of buckets, a bucket per chunk size.
Once a bucket is empty we will cut a row of memory from the latest
allocated MR, if the MR size is not sufficient we will allocate a new MR.
HW design requires that chunks memory address should be aligned to the
chunk size, this is the reason for managing the MR with row size that
insures memory alignment.
Current design is greedy in memory but provides quick allocation times
in steady state.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add direct rule command utilities which consists of all the FW
commands that are executed to provide the SW steering functionality.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the internal header file that contains various types
definition that will be used in coming patches as well as
the internal functions decelerations.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Erez Shitrit <erezsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add flow steering actions: modify header and packet reformat
to the fs_cmd shim layer. This allows each namespace to define
possibly different functionality for alloc/dealloc action commands.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Every mvpp2 unit can use up to 8 buffers mapped by the BM (the HW buffer
manager). The HW will place the frames in the buffer pool depending on the
frame size: short (< 128 bytes), long (< 1664) or jumbo (up to 9856).
As any unit can have up to 4 ports, the driver allocates only 2 pools,
one for small and one long frames, and share them between ports.
When the first port MTU is set higher than 1664 bytes, a third pool is
allocated for jumbo frames.
This shared allocation makes impossible to use percpu allocators,
and creates contention between HW queues.
If possible, i.e. if the number of possible CPU are less than 8 and jumbo
frames are not used, switch to a new scheme: allocate 8 per-cpu pools for
short and long frames and bind every pool to an RXQ.
When the first port MTU is set higher than 1664 bytes, the allocation
scheme is reverted to the old behaviour (3 shared pools), and when all
ports MTU are lowered, the per-cpu buffers are allocated again.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor mvpp2_bm_pool_create(), mvpp2_bm_pool_destroy() and
mvpp2_bm_pools_init() so that they accept a struct device instead
of a struct platform_device, as they just need platform_device->dev.
Removing such dependency makes the BM code more reusable in context
where we don't have a pointer to the platform_device.
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Take only FIB events that are happening in init_net into account. No other
namespaces are supported.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
r8152 conflicts are the NAPI fixes in 'net' overlapping with
some tasklet stuff in net-next
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are some small char and misc driver fixes for reported issues for
5.3-rc7
Also included in here is the documentation for how we are handling
hardware issues under embargo that everyone has finally agreed on, as
well as a MAINTAINERS update for the suckers who agreed to handle the
LICENSES/ files.
All of these have been in linux-next last week with no reported
issues"
* tag 'char-misc-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
fsi: scom: Don't abort operations for minor errors
vmw_balloon: Fix offline page marking with compaction
VMCI: Release resource if the work is already queued
Documentation/process: Embargoed hardware security issues
lkdtm/bugs: fix build error in lkdtm_EXHAUST_STACK
mei: me: add Tiger Lake point LP device ID
intel_th: pci: Add Tiger Lake support
intel_th: pci: Add support for another Lewisburg PCH
stm class: Fix a double free of stm_source_device
MAINTAINERS: add entry for LICENSES and SPDX stuff
fpga: altera-ps-spi: Fix getting of optional confd gpio
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB fixes that have been in linux-next this past
week for 5.3-rc7
They fix the usual xhci, syzbot reports, and other small issues that
have come up last week.
All have been in linux-next with no reported issues"
* tag 'usb-5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: cdc-wdm: fix race between write and disconnect due to flag abuse
usb: host: xhci: rcar: Fix typo in compatible string matching
usb: host: xhci-tegra: Set DMA mask correctly
USB: storage: ums-realtek: Whitelist auto-delink support
USB: storage: ums-realtek: Update module parameter description for auto_delink_en
usb: host: ohci: fix a race condition between shutdown and irq
usb: hcd: use managed device resources
typec: tcpm: fix a typo in the comparison of pdo_max_voltage
usb-storage: Add new JMS567 revision to unusual_devs
usb: chipidea: udc: don't do hardware access if gadget has stopped
usbtmc: more sanity checking for packet size
usb: udc: lpc32xx: silence fall-through warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Merge mlx5-next patches needed for upcoming mlx5 software steering.
1) Alex adds HW bits and definitions required for SW steering
2) Ariel moves device memory management to mlx5_core (From mlx5_ib)
3) Maor, Cleanups and fixups for eswitch mode and RoCE
4) Mark, Set only stag for match untagged packets
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
cvlan_tag enabled in match criteria and disabled in
match value means both S & C tags don't exist (untagged of both).
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move the check if RoCE steering is initialized to the
disable RoCE function, it will ensure that we disable
RoCE only if we succeeded in enabling it before.
Fixes: 80f09dfc237f ("net/mlx5: Eswitch, enable RoCE loopback traffic")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move the device memory allocation and deallocation commands
SW ICM memory to mlx5_core to expose this API for all
mlx5_core users.
This comes as preparation for supporting SW steering in kernel
where it will be required to allocate and register device
memory for direct rule insertion.
In addition, an API to register this device memory for future
remote access operations is introduced using the create_mkey
commands.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Pull networking fixes from David Miller:
1) Fix some length checks during OGM processing in batman-adv, from
Sven Eckelmann.
2) Fix regression that caused netfilter conntrack sysctls to not be
per-netns any more. From Florian Westphal.
3) Use after free in netpoll, from Feng Sun.
4) Guard destruction of pfifo_fast per-cpu qdisc stats with
qdisc_is_percpu_stats(), from Davide Caratti. Similar bug is fixed
in pfifo_fast_enqueue().
5) Fix memory leak in mld_del_delrec(), from Eric Dumazet.
6) Handle neigh events on internal ports correctly in nfp, from John
Hurley.
7) Clear SKB timestamp in NF flow table code so that it does not
confuse fq scheduler. From Florian Westphal.
8) taprio destroy can crash if it is invoked in a failure path of
taprio_init(), because the list head isn't setup properly yet and
the list del is unconditional. Perform the list add earlier to
address this. From Vladimir Oltean.
9) Make sure to reapply vlan filters on device up, in aquantia driver.
From Dmitry Bogdanov.
10) sgiseeq driver releases DMA memory using free_page() instead of
dma_free_attrs(). From Christophe JAILLET.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
net: seeq: Fix the function used to release some memory in an error handling path
enetc: Add missing call to 'pci_free_irq_vectors()' in probe and remove functions
net: bcmgenet: use ethtool_op_get_ts_info()
tc-testing: don't hardcode 'ip' in nsPlugin.py
net: dsa: microchip: add KSZ8563 compatibility string
dt-bindings: net: dsa: document additional Microchip KSZ8563 switch
net: aquantia: fix out of memory condition on rx side
net: aquantia: linkstate irq should be oneshot
net: aquantia: reapply vlan filters on up
net: aquantia: fix limit of vlan filters
net: aquantia: fix removal of vlan 0
net/sched: cbs: Set default link speed to 10 Mbps in cbs_set_port_rate
taprio: Set default link speed to 10 Mbps in taprio_set_picos_per_byte
taprio: Fix kernel panic in taprio_destroy
net: dsa: microchip: fill regmap_config name
rxrpc: Fix lack of conn cleanup when local endpoint is cleaned up [ver #2]
net: stmmac: dwmac-rk: Don't fail if phy regulator is absent
amd-xgbe: Fix error path in xgbe_mod_init()
netfilter: nft_meta_bridge: Fix get NFT_META_BRI_IIFVPROTO in network byteorder
mac80211: Correctly set noencrypt for PAE frames
...
|
|
The .serdes_irq_setup are all following the same steps: get the SERDES
lane, get the IRQ mapping, request the IRQ, then enable it. So do
the .serdes_irq_free implementations: get the SERDES lane, disable
the IRQ, then free it.
This patch removes these operations in favor of generic functions.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new .serdes_irq_status operation to prepare the abstraction
of IRQ thread from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a new .serdes_irq_enable operation to prepare the abstraction
of IRQ enabling from the SERDES IRQ setup code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now the first step of all .serdes_power implementations is getting
the lane mapping. Since we have an operation for that, call it in
the wrapper and pass the lane down to the .serdes_power operation.
This also allows to avoid querying the SERDES lane twice in
mv88e6xxx_port_set_cmode.
At the same time provide mv88e6xxx_serdes_power_{up,down} helpers
and prefer up/down instead of on/off as in the documentation.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|