| Age | Commit message (Collapse) | Author |
|---|
|
* Rename ide_noacpi{tfs,onboot} to ide_acpi{gtf,onboot} (+ reverse logic).
* Move ide_*acpi* variables to ide-acpi.c and remove unnecessary initializers.
* Add "noacpi" / "acpigtf" / "acpionboot" parameters.
* Obsolete "ide=noacpi" / "ide=acpigtf" / "ide=acpionboot" kernel parameters.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add "doubler" parameter to enable support for IDE doublers.
* Obsolete "ide=doubler" kernel parameter.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add "cdrom=" and "chs=" parameters.
* Obsolete "hdx=cdrom" and "hdx=cyls,heads,sects" kernel parameters.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add "nodma|noflush|noprobe|nowerr=" parameters.
* Obsolete "hdx=noprobe|none|nowerr|nodma|noflush" kernel parameters.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Remove obsoleted "hdx=autotune" kernel parameter
(we always auto-tune PIO if possible nowadays).
* Remove no longer needed ide_drive_t.autotune flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Don't set IDE_HFLAG_NO_AUTOTUNE host flag in sgiioc4 and icside
host drivers - there is no need for it as they don't implement
->set_pio_mode method.
* Remove no longer needed IDE_HFLAG_NO_AUTOTUNE host flag.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Default to tuning PIO0 and disabling prefetch prior to probing
devices for CONFIG_BLK_DEV_CMD640_ENHANCED=y case.
* Always auto-tune PIO.
* Remove no longer used retrieve_drive_counts().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
We have "vlb|pci_clock=" parameters now.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add "vlb_clock=" parameter for specifying VLB clock frequency (in MHz).
* Add "pci_clock=" parameter for specifying PCI bus clock frequency (in MHz).
While at it:
* qd65xx.c: rename {active,recovery}_cycle variables to {act,rec}_cyc.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Bart:
- merge "ide-tape: remove pipeline-specific code from idetape_setup" patch
- cleanup __idetape_discard_read_pipeline()
- cleanup idetape_empty_write_pipeline()
- fix 't' assignment in idetape_setup()
- fix idetape_blkdev_ioctl() w.r.t. 'nr_stages'
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
[bart: sync patch with current code and fix idetape_init_read()]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
The driver is using now solely its own request queue.
- tape->next_stage is always NULL so it is safe to remove
all code depending on tape->next_stage != NULL
- this patch removes the last place which sets
IDETAPE_FLAG_PIPELINE_ACTIVE in tape->flags
[bart: add above explanations]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
idetape_queue_pc_tail() is a wrapper for its __idetape_queue_pc_tail() counterpart
and has no other functionality. Remove it and call the "wrapped" function
directly.
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
As a side effect, remove unused idetape_kfree_stage() and
idetape_abort_pipeline()
[bart: resurrect taking tape->lock + clearing IDETAPE_FLAG_PIPELINE_ACTIVE]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
The computation of the block offset of the the tape position (MTIOCPOS,
MTIOCGET) is not influenced by the stages queued in the pipeline anymore but by
the size of the current buffer which is going to be sent to the drive.
[bart: resurrect deleted idetape_wait_for_pipeline() call]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Since we don't do pipeline read-ahead anymore, we don't have to look for
filemarks we have crossed. Therefore, remove the code chunk that does that and
pass on the command to the tape. As a side effect, remove unused
idetape_wait_first_stage().
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
In order to do away with queueing read requests on the pipeline, several things
have to be done:
1. Do not allocate additional pipeline stages in idetape_init_read() until
(tape->nr_stages < max_stages) and do only read operation preparations. As a
collateral result, idetape_add_stage_tail() becomes unused so remove it.
2. Queue the read request's buffer directly thru idetape_queue_rw_tail().
3. Remove now unused idetape_kmalloc_stage() and idetape_switch_buffers().
[bart: simplify the original patch]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Pipeline handling calculations in idetape_calculate_speeds() can
go since they do not have any effect on other functionality besides:
1. info is only being exported through /proc as a read-only item
(controlled_pipeline_head_speed, uncontrolled_pipeline_head_speed)
2. used in idetape_restart_speed_control() which, in turn, is unrelated to
other code
3. used only for pipeline frames number accounting (tape->pipeline_head),
also unused elsewhere.
4.some variables are:
only written to: tape->buffer_head;
unused: tape->tape_head, tape->last_tape_head
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Refrain from adding more write requests to the pipeline and queue them
directly on the device's request queue instead.
[bart: re-do for minimal behavior changes]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Prior to allocating a new pipeline stage, the code checked for the existence of
a cached pipeline stage to use. Do away with and stick to normal pipeline
stages only.
[bart: keep idetape_kmalloc_stage() for now]
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove obsoleted "hdx=noautotune" kernel parameter
(it has been obsoleted since 1 Nov 2004).
Then make ide_hwif_t.autotune a single bit flag
and remove no longer needed IDE_TUNE_* defines.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Remove obsoleted "idex=" kernel parameters.
* Make probe_* and cmd640_vlb variables static.
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove obsoleted "idex=reset" kernel parameter
(it has been obsoleted since 1 Nov 2004).
Then remove corresponding code from ide_probe_port()
and no longer used ->reset field from ide_hwif_t.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Remove obsoleted "idex=serialize" kernel parameter
(it has been obsoleted since 1 Nov 2004).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add "ignore_cable" parameter:
* "ide_core.ignore_cable=[interface_number]" boot option if IDE is built-in
(i.e. "ide_core.ignore_cable=1" to force ignoring cable for "ide1")
* "ignore_cable=[interface_number]" module parameter (for ide_core module)
if IDE is compiled as module
v2:
* Add ide_port_apply_params() helper
- use it in ide_device_add_all() and ide_scan_port().
* Make it possible to later disable ignoring cable detection by passing
"[interface_number]:0" to /sys/module/ide_core/parameters/ignore_cable
(however sysfs interface is not enabled yet since it needs some other
IDE changes to make it work reliable).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Fallout from commit ac95beedf8bc97b24f9540d4da9952f07221c023
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Export ide_dma_exec_cmd() and __ide_dma_test_irq().
* Constify struct ide_dma_ops.
* Always set hwif->dma_ops to &sff_dma_ops in ide_setup_dma()
(it is later overriden by ide_init_port() if needed) and drop
'const struct ide_port_info *d' argument.
While at it:
* Rename __ide_dma_test_irq() to ide_dma_test_irq().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Add struct ide_dma_ops and convert core code + drivers to use it.
While at it:
* Drop "ide_" prefix from ->ide_dma_end and ->ide_dma_test_irq methods.
* Drop "ide_" "infixes" from DMA methods.
* au1xxx-ide.c:
- use auide_dma_{test_irq,end}() directly in auide_dma_timeout()
* pdc202xx_old.c:
- drop "old_" "infixes" from DMA methods
* siimage.c:
- add siimage_dma_test_irq() helper
- print SATA warning in siimage_init_one()
* Remove no longer needed ->init_hwif implementations.
v2:
* Changes based on review from Sergei:
- s/siimage_ide_dma_test_irq/siimage_dma_test_irq/
- s/drive->hwif/hwif/ in idefloppy_pc_intr().
- fix patch description w.r.t. au1xxx-ide changes
- fix au1xxx-ide build
- fix naming for cmd64*_dma_ops
- drop "ide_" and "old_" infixes
- s/hpt3xxx_dma_ops/hpt37x_dma_ops/
- s/hpt370x_dma_ops/hpt370_dma_ops/
- use correct DMA ops for HPT302/N, HPT371/N and HPT374
- s/it821x_smart_dma_ops/it821x_pass_through_dma_ops/
v3:
* Two bugs slipped in v2 (noticed by Sergei):
- use correct DMA ops for HPT374 (for real this time)
- handle HPT370/HPT370A properly
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add IDE_HFLAG_SERIALIZE_DMA host flag to serialize ports
if DMA is available and handle it in ide_init_port().
* Convert sl82c105 host driver to use this new flag.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make sl82c105_bridge_revision() return 'u8' instead of 'unsigned long'.
* Check bridge revision in sl82c105_init_one().
While at:
* Use proper KERN_ level for printk().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Pass 'ide_hwif_t *hwif' instead of '_auide_hwif *auide' to
auide_ddma_init().
* Add 'const struct ide_port_info *d' argument to auide_ddma_init().
* Convert the driver to use ->init_dma method.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move DMA setup to palm_bk3710_init_dma().
* Convert the driver to use ->init_dma method.
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move dma_base check from sgiioc4_ide_setup_pci_device()
to ide_dma_sgiioc4().
* Replace ide_dma_sgiioc4() 'unsigned long dma_base' argument
by 'const struct ide_port_info *d'.
* Move hwif->INB setup from ide_init_sgiioc4() to
sgiioc4_ide_setup_pci_device().
* Move ide_init_sgiioc4() call from sgiioc4_ide_setup_pci_device()
to ide_dma_sgiioc4().
* Convert the driver to use ->init_dma method.
Cc: Jeremy Higdon <jeremy@sgi.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Add 'const struct ide_port_info *d' argument to icside_dma_init().
* Make icside_dma_init() return an error value and add icside_dma_off_init()
(->init_dma implementation for case when DMA cannot be enabled).
* Convert the driver to use ->init_dma method.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Move pmif->dma_regs check from pmac_ide_setup_device() to
pmac_ide_init_dma().
* Get 'pmif' from 'hwif->hwif_data' in pmac_ide_init_dma() and replace
'pmac_ide_hwif_t *pmif' argument by 'const struct ide_port_info *d'.
* Add pmac_ide_init_dma() implementation for CONFIG_BLK_DEV_IDEDMA_PMAC=n
case and convert the driver to use ->init_dma method.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* Make ide_hwif_setup_dma() return an error value.
* Pass 'const struct ide_port_info *d' instead of 'unsigned long dmabase'
to ->init_dma method and make it return an error value.
* Rename ide_get_or_set_dma_base() to ide_pci_dma_base(),
change ordering of its arguments and then export it.
* Export ide_pci_set_master().
* Do complete DMA setup inside ->init_dma method and update ->init_dma
users accordingly.
* Sanitize code for DMA setup in ide_init_port().
v2:
* Fix for CONFIG_BLK_DEV_IDEDMA_PCI=n configs
(from Jiri Slaby <jirislaby@gmail.com>):
Fix following compiler warning by returning EINVAL:
In file included from ANYTHING-INCLUDING-IDE.H:45:
include/linux/ide.h: In function ‘ide_hwif_setup_dma’:
include/linux/ide.h:1022: warning: no return statement in function returning non-void
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Always use "fast" MWDMA support and remove dma_{black,white}_list
(they were based on completely bogus ->ide_dma_check implementation
which didn't set neither the host controller timings nor the device
for the desired transfer mode).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
* There is no need to call ide_release_dma_engine().
* Move the code up to (and including) ide_allocate_dma_engine()
call to the callers of ide_setup_dma().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Factor out setting PCI bus-mastering from ide_hwif_setup_dma()
to ide_pci_set_master() helper.
While at it:
* don't read PCI Command register if not necessary
* use PCI device name instead of hwif->name
* cleanup ide_hwif_setup_dma() a bit
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Export ide_allocate_dma_engine() and use it in trm290 host driver.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Skip DMA initialization completely on revs < 0x20 by setting IDE_HFLAG_NO_DMA
host flag and resetting DMA host masks in alim15x3_init_one() (currently
ide_hwif_setup_dma() will try to obtain DMA base and setup PCI bus-mastering
but init_dma_ali15x3() will fail).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Do PDC202xx specific DMA initialization in init_chipset_pdc202xx()
and remove no longer needed init_dma_pdc202xx().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
|
Nowadays BIOS info is not very useful and only confuses users since:
- IDE always tries to use DMA
- BIOS info may not be accurate with modular IDE/libata
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
|
