| Age | Commit message (Collapse) | Author |
|---|
|
if a full speed hub connects to a high speed hub which
supports MTT, the MTT field of its slot context will be set
to 1 when xHCI driver setups an xHCI virtual device in
xhci_setup_addressable_virt_dev(); once usb core fetch its
hub descriptor, and need to update the xHC's internal data
structures for the device, the HUB field of its slot context
will be set to 1 too, meanwhile MTT is also set before,
this will cause configure endpoint command fail, so in the
case, we should clear MTT to 0 for full speed hub according
to section 6.2.2
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Existing Intel xHCI controllers require a delay of 1 mS,
after setting the CMD_RESET bit in command register, before
accessing any HC registers. This allows the HC to complete
the reset operation and be ready for HC register access.
Without this delay, the subsequent HC register access,
may result in a system hang, very rarely.
Verified CherryView / Braswell platforms go through over
5000 warm reboot cycles (which was not possible without
this patch), without any xHCI reset hang.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Tested-by: Joe Lawrence <joe.lawrence@stratus.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This change avoids DMA error in the cases where dma_mask and
coherent_dma_mask of a 32-bit controller get configured as
DMA_BIT_MASK(64) when running on a 64-bit system.
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Set the controller speed to HCD_USB31 to if host hardware supports USB 3.1
For PCI xhci controllers the USB 3.1 support is checked from SBRN bits in
pci config space. Platform controllers will need to set xhci->sbrn == 0x31
to indicate USB 3.1 support before calling xhci_gen_setup().
Also make sure xhci driver works correctly with speed set to HCD_USB31
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci 1.1 capable controllers have a new HCCPARAMS2 registers
with bits indicating support for new xhci 1.1 capabilities.
Also add support for the new xhci 1.1 bits in the config operational
opertational register that used to be reserved
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
[modified and left out parts not related to HCCPARAMS2 -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During quick plug/removal of OTG adapter during dual-role testing
it can happen that xhci_alloc_device() is called for the newly
detected device after the DRD library has called xhci_stop to
remove the HCD.
If that is the case, just fail early to prevent the following warning.
[ 154.732649] hub 4-0:1.0: USB hub found
[ 154.742204] hub 4-0:1.0: 1 port detected
[ 154.824458] hub 3-0:1.0: state 7 ports 1 chg 0002 evt 0000
[ 154.854609] hub 4-0:1.0: state 7 ports 1 chg 0000 evt 0000
[ 154.944430] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[ 154.951009] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.038191] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 155.043315] usb usb4: USB disconnect, device number 1
[ 155.055270] xhci-hcd xhci-hcd.0.auto: xhci_stop
[ 155.060094] xhci-hcd xhci-hcd.0.auto: USB bus 4 deregistered
[ 155.066576] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 155.071710] usb usb3: USB disconnect, device number 1
[ 155.077124] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.082389] ------------[ cut here ]------------
[ 155.087690] WARNING: CPU: 0 PID: 72 at drivers/usb/host/xhci.c:3800 xhci_setup_device+0x410/0x484 [xhci_hcd]()
[ 155.097861] Modules linked in: sd_mod usb_storage scsi_mod usb_f_ss_lb g_zero libcomposite ipv6 xhci_plat_hcd xhci_hcd usbcore dwc3 udc_core evdev ti_am335x_adc joydev kfifo_buf industrialio snd_soc_simple_cc
[ 155.146734] CPU: 0 PID: 72 Comm: kworker/0:3 Tainted: G W 4.1.4-00834-gcd9380b-dirty #50
[ 155.156073] Hardware name: Generic AM43 (Flattened Device Tree)
[ 155.162117] Workqueue: usb_hub_wq hub_event [usbcore]
[ 155.167249] Backtrace:
[ 155.169751] [<c0012af0>] (dump_backtrace) from [<c0012c8c>] (show_stack+0x18/0x1c)
[ 155.177390] r6:c089d4a4 r5:ffffffff r4:00000000 r3:ee46c000
[ 155.183137] [<c0012c74>] (show_stack) from [<c05f7c14>] (dump_stack+0x84/0xd0)
[ 155.190446] [<c05f7b90>] (dump_stack) from [<c00439ac>] (warn_slowpath_common+0x80/0xbc)
[ 155.198605] r7:00000009 r6:00000ed8 r5:bf27eb70 r4:00000000
[ 155.204348] [<c004392c>] (warn_slowpath_common) from [<c0043a0c>] (warn_slowpath_null+0x24/0x2c)
[ 155.213202] r8:ee49f000 r7:ee7c0004 r6:00000000 r5:ee7c0158 r4:ee7c0000
[ 155.220051] [<c00439e8>] (warn_slowpath_null) from [<bf27eb70>] (xhci_setup_device+0x410/0x484 [xhci_hcd])
[ 155.229816] [<bf27e760>] (xhci_setup_device [xhci_hcd]) from [<bf27ec10>] (xhci_address_device+0x14/0x18 [xhci_hcd])
[ 155.240415] r10:ee598200 r9:00000001 r8:00000002 r7:00000001 r6:00000003 r5:00000002
[ 155.248363] r4:ee49f000
[ 155.250978] [<bf27ebfc>] (xhci_address_device [xhci_hcd]) from [<bf20cb94>] (hub_port_init+0x1b8/0xa9c [usbcore])
[ 155.261403] [<bf20c9dc>] (hub_port_init [usbcore]) from [<bf2101e0>] (hub_event+0x738/0x1020 [usbcore])
[ 155.270874] r10:ee598200 r9:ee7c0000 r8:ee7c0038 r7:ee518800 r6:ee49f000 r5:00000001
[ 155.278822] r4:00000000
[ 155.281426] [<bf20faa8>] (hub_event [usbcore]) from [<c005754c>] (process_one_work+0x128/0x340)
[ 155.290196] r10:00000000 r9:00000003 r8:00000000 r7:fedfa000 r6:eeec5400 r5:ee598314
[ 155.298151] r4:ee434380
[ 155.300718] [<c0057424>] (process_one_work) from [<c00578f8>] (worker_thread+0x158/0x49c)
[ 155.308963] r10:ee434380 r9:00000003 r8:eeec5400 r7:00000008 r6:ee434398 r5:eeec5400
[ 155.316913] r4:eeec5414
[ 155.319482] [<c00577a0>] (worker_thread) from [<c005cc40>] (kthread+0xdc/0xf8)
[ 155.326765] r10:00000000 r9:00000000 r8:00000000 r7:c00577a0 r6:ee434380 r5:ee4441c0
[ 155.334713] r4:00000000 r3:00000000
[ 155.338341] [<c005cb64>] (kthread) from [<c000fc08>] (ret_from_fork+0x14/0x2c)
[ 155.345626] r7:00000000 r6:00000000 r5:c005cb64 r4:ee4441c0
[ 155.356108] ---[ end trace a58d34c223b190e6 ]---
[ 155.360783] xhci-hcd xhci-hcd.0.auto: Virt dev invalid for slot_id 0x1!
[ 155.574404] xhci-hcd xhci-hcd.0.auto: xhci_setup_device
[ 155.579667] ------------[ cut here ]------------
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_stop will be called twice, once for the shared hcd
and again for the primary hcd.
We stop the XHCI controller in any case so clean up
everything on the first call else we can timeout
waiting for pending requests to complete.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For whatever reason if XHCI died in the previous instant
then it will never recover on the next xhci_start unless we
clear the DYING flag.
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Else it races with xhci_setup_device
Cc: <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit checks for the URB_ZERO_PACKET flag and creates an extra
zero-length td if the urb transfer length is a multiple of the endpoint's
max packet length.
Signed-off-by: Reyad Attiyat <reyad.attiyat@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Replace redundant variable use in return statement.
Signed-off-by: Saurabh Karajgaonkar <skarajga@visteon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the USB fixes that went into that release in this branch as
well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix "though" to "through" in documentation of xhci_alloc_streams().
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When resetting a device the number of active TTs may need to be
corrected by xhci_update_tt_active_eps, but the number of old active
endpoints supplied to it was always zero, so the number of TTs and the
bandwidth reserved for them was not updated, and could rise
unnecessarily.
This affected systems using Intel's Patherpoint chipset, which rely on
software bandwidth checking. For example, a Lenovo X230 would lose the
ability to use ports on the docking station after enough suspend/resume
cycles because the bandwidth calculated would rise with every cycle when
a suitable device is attached.
The correct number of active endpoints is calculated in the same way as
in xhci_reserve_bandwidth.
Cc: <stable@vger.kernel.org>
Signed-off-by: Brian Campbell <bacam@z273.org.uk>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The comment stating that xhci_setup_device() is protected by the address
mutex is not true since
commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus")
as xhci handles two buses.
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the OTG case, the controller might not yet have been
added or is removed before the system suspends.
Assign xhci->main_hcd during probe to prevent NULL
pointer de-reference in xhci_suspend/resume().
Use the hcd->state flag to check if HCD is halted
and if that is so do nothing for xhci_suspend/resume().
[Only for xhci-plat devices, pci devices need it in gen_setup -Mathias]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't set xhci->shared_hcd to NULL in xhci_stop() as we have
still not de-allocated it. It was resulting in a NULL pointer
de-reference if usb_add/remove_hcd() is called repeatedly.
We want repeated add/remove to work for the OTG use case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HCD core allocates memory for HCD private data in
usb_create_[shared_]hcd() so make use of that
mechanism to allocate the struct xhci_hcd.
Introduce struct xhci_driver_overrides to provide
the size of HCD private data and hc_driver operation
overrides. As of now we only need to override the
reset and start methods.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Regression in commit 638139eb95d2 ("usb: hub: allow to process more usb
hub events in parallel")
The regression resulted in intermittent failure to initialise a 10-port
hub (with three internal VL812 4-port hub controllers) on boot, with a
failure rate of around 8%, due to multiple race conditions when
accessing addr_dev and slot_id in struct xhci_hcd.
This regression also exposed a problem with xhci_setup_device, which
"should be protected by the usb_address0_mutex" but no longer is due to
commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus")
With separate buses (and locks) it is no longer the case that a single
lock will protect xhci_setup_device from accesses by two parallel
threads processing events on the two buses.
Fix this by adding a mutex to protect addr_dev and slot_id in struct
xhci_hcd, and by making the assignment of slot_id atomic.
Fixes multiple boot errors:
[ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2
[ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures
[ 0.583012] usb usb1-port3: couldn't allocate usb_device
And:
[ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.637421] usb usb1-port1: couldn't allocate usb_device
And:
[ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0.
[ 0.753373] usb 1-3: hub failed to enable device, error -22
[ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.753403] usb usb1-port3: couldn't allocate usb_device
And:
[ 11.018386] usb 1-3: device descriptor read/all, error -110
And:
[ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
Tested with 200 reboots, resulting in no USB hub init related errors.
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.com
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
[changed git commit description style for checkpatch -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixed regression. After commit 29e409f0f761 ("xhci: Allow xHCI drivers to
be built as separate modules") the module xhci_hcd became non-removable.
That behaviour is not expected and there're no notes about it in commit
message. The module should be removable as it blocks PM suspend/resume
functions (Debian Bug#666406).
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 27082e2654dc ("xhci: Clear the host side toggle manually")
Turns out this fix to enable soft resetting endpoints wasn't mature enough.
It caused regression with some usb DVB-T devices and needs some more tuning
to get the endpiont ring pointers set correctly.
The original commit was tagged for stable 3.18, and should be reverted
from there as well.
Cc: stable <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Main benefit of this is to get xhci connected USB scanners to work.
Some devices use a clear endpoint halt request as a 'soft reset' even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side. xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host side
toggle and sequence, and get it in sync with the device side.
Tested-by: Mike Mammarella <mikem@crystalorb.net>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When re-applying the configuration after a successful usb device reset,
xhci_discover_or_reset_device has already dropped the endpoints, and free-ed
the rings.
The endpoints already being dropped is expected, and should not lead to
warnings. Use the fact that the rings are also free-ed in this scenario to
detect this, and suppress the "xHCI xhci_drop_endpoint called with disabled
ep ..." message in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
--
Changes in v2:
Move the ring check to only guard the xhci_warn, so as to avoid side-effects
in case we have a scenario where the rings are free-ed, but the endpoint is
not yet dropped.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To help debugging xhci problems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the usb fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some parameters are not used by functions in xhci-mem.c, just
remove it.
Changes compared to v1:
- Rebase to the latest usb-next branch
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert a call to init_timer and accompanying intializations of
the timer's data and function fields to a call to setup_timer.
A simplified version of the semantic match that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression t,f,d;
@@
-init_timer(&t);
+setup_timer(&t,f,d);
-t.data = d;
-t.function = f;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Parameter 'xhci' is no longer be used in function xhci_handshake(),
just remove it.
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch removes unused variable "out_ctx" and avoid multiple calls
to function xhci_get_endpoint_flag().
Signed-off-by: Lin Wang <lin.x.wang@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Solves xhci error cases with debug messages:
xhci_hcd 0000:00:14.0: Setup ERROR: setup context command for slot 1.
usb 1-6: hub failed to enable device, error -22
xhci will give a context state error if we try to set a slot in default
state to the same default state with a special address device command.
Turns out this happends in several cases:
- retry reading the device rescriptor in hub_port_init()
- usb_reset_device() is called for a slot in default state
- in resume path, usb_port_resume() calls hub_port_init()
The default state is usually reached from most states with a reset device
command without any context state errors, but using the address device
command with BSA bit set (block set address) only works from the enabled
state and will otherwise cause context error.
solve this by checking if we are already in the default state before issuing
a address device BSA=1 command.
Fixes: 48fc7dbd52c0 ("usb: xhci: change enumeration scheme to 'new scheme'")
Cc: <stable@vger.kernel.org> # v3.14+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big set of USB and PHY patches for 3.19-rc1.
The normal churn in the USB gadget area is in here, as well as xhci
and other individual USB driver updates. The PHY tree is also in
here, as there were dependancies on the USB tree.
All of these have been in linux-next"
* tag 'usb-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (351 commits)
arm: omap3: twl: remove usb phy init data
usbip: fix error handling in stub_probe()
usb: gadget: udc: missing curly braces
USB: mos7720: delete some unneeded code
wusb: replace memset by memzero_explicit
usbip: remove unneeded structure
usb: xhci: fix comment for PORT_DEV_REMOVE
xhci: don't use the same variable for stopped and halted rings current TD
xhci: clear extra bits from slot context when setting max exit latency
xhci: cleanup finish_td function
USB: adutux: NULL dereferences on disconnect
usb: chipidea: fix platform_no_drv_owner.cocci warnings
usb: chipidea: Fixed a few typos in comments
Documentation: bindings: add doc for the USB2 ChipIdea USB driver
usb: chipidea: add a usb2 driver for ci13xxx
usb: chipidea: fix phy handling
usb: chipidea: remove duplicate dev_set_drvdata for host_start
usb: chipidea: parameter 'mode' isn't needed for hw_device_reset
usb: chipidea: add controller reset API
usb: chipidea: remove flag CI_HDRC_REQUIRE_TRANSCEIVER
...
|
|
* pm-runtime: (25 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
PM / Kconfig: Do not select PM directly from Kconfig files
PCI / PM: Drop CONFIG_PM_RUNTIME from the PCI core
...
|
|
After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so quite a few
depend on CONFIG_PM (or even dropped in some cases).
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the USB core code
and documentation.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Endpoints halted on errors, and endpoints stopped manually both used
the same ep->stopped_td to store the halted or stopped td. this causes
confusion and possible races.
There is no longer a need to use the ep->stopped_td variable to store
the halted TD. A halted endpoint is handled immediately and we can pass
it to the handling function directly.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we need to change the max exit latency with a Evaluate Context
command, we copy the old output slot context and use it as input
context for the command. This also copies the dev_state bits which
are supposed to be zero in the input slot context.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When system is being suspended, if host device is not allowed to do wakeup,
xhci_suspend() needs to clear all root port wake on bits. Otherwise, some
platforms may generate spurious wakeup, even if PCI PME# is disabled.
The initial commit ff8cbf250b44 ("xhci: clear root port wake on bits"),
which also got into stable, turned out to not work correctly and had to
be reverted, and is now rewritten.
Cc: stable <stable@vger.kernel.org> # v3.2+
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
[Mathias Nyman: reword commit message]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a device is halted and reuturns a STALL, then the halted endpoint
needs to be cleared both on the host and device side. The host
side halt is cleared by issueing a xhci reset endpoint command. The device side
is cleared with a ClearFeature(ENDPOINT_HALT) request, which should
be issued by the device driver if a URB reruen -EPIPE.
Previously we cleared the host side halt after the device side was cleared.
To make sure the host side halt is cleared in time we want to issue the
reset endpoint command immedialtely when a STALL status is encountered.
Otherwise we end up not following the specs and not returning -EPIPE
several times in a row when trying to transfer data to a halted endpoint.
Fixes: bcef3fd (USB: xhci: Handle errors that cause endpoint halts.)
Cc: <stable@vger.kernel.org> # v2.6.33+
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of building all of the xHCI code into a single module, separate
it out into the core (xhci-hcd), PCI (xhci-pci, now selected by the new
config option CONFIG_USB_XHCI_PCI), and platform (xhci-plat) drivers.
Also update the PCI/platform drivers with module descriptions/licenses
and have them register their respective drivers in their initcalls.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In preparation for allowing the xHCI host controller drivers to be built
as separate modules, export symbols from the xHCI core that may be used
by the host controller drivers.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of calling xhci_compliance_mode_recovery_timer_quirk_check() again
in the PCI suspend path, just check for XHCI_COMP_MODE_QUIRK which will
have been set based on xhci_compliance_mode_recovery_timer_quirk_check()
in xhci_init().
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the struct hc_driver is mostly the same across the xhci-pci,
xhci-plat, and the upcoming xhci-tegra driver, introduce the function
xhci_init_driver() which will populate the hc_driver with the default
xHCI operations. The caller must supply a setup function which will
be used as the hc_driver's reset callback.
Note that xhci-plat also overrides the default ->start() callback so
that it can do rcar-specific initialization.
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
USB hub has started to use a workqueue instead of kthread. Let's update
the documentation and comments here and there.
This patch mostly just replaces "khubd" with "hub_wq". There are only few
exceptions where the whole sentence was updated. These more complicated
changes can be found in the following files:
Documentation/usb/hotplug.txt
drivers/net/usb/usbnet.c
drivers/usb/core/hcd.c
drivers/usb/host/ohci-hcd.c
drivers/usb/host/xhci.c
Signed-off-by: Petr Mladek <pmladek@suse.cz>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
V2 - Restart polling (which will restart the timer) for the shared
HCD in xhci_resume().
xhci_suspend() will stop the primary HCD's root hub timer, but leaves
the shared HCD's timer running. This change adds stopping of the
shared HCD timer.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are multiple reasons for this:
1) This fixes a missing check for xhci_alloc_command failing in
xhci_handle_cmd_stop_ep()
2) This adds a warning when we cannot set the new dequeue state because of
xhci_alloc_command failing
3) It puts the allocation of the command after the sanity checks in
queue_set_tr_deq(), avoiding leaking the command if those fail
4) Since queue_set_tr_deq now owns the command it can free it if queue_command
fails
5) It reduces code duplication
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resuming from hibernate (S4) will restart and re-initialize xHC.
The device contexts are freed and will be re-allocated later during device reset.
Usb core will disable link pm in device resume before device reset, which will
try to change the max exit latency, accessing the device contexts before they are re-allocated.
There is no need to zero (disable) the max exit latency when disabling hw lpm
for a freshly re-initialized xHC. So check that device context exists before
doing anything. The max exit latency will be set again after device reset when usb core
enables the link pm.
Reported-by: Imre Deak <imre.deak@intel.com>
Tested-by: Imre Deak <imre.deak@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When we manually need to move the TR dequeue pointer we need to set the
correct cycle bit as well. Previously we used the trb pointer from the
last event received as a base, but this was changed in
commit 1f81b6d22a59 ("usb: xhci: Prefer endpoint context dequeue pointer")
to use the dequeue pointer from the endpoint context instead
It turns out some Asmedia controllers advance the dequeue pointer
stored in the endpoint context past the event triggering TRB, and
this messed up the way the cycle bit was calculated.
Instead of adding a quirk or complicating the already hard to follow cycle bit
code, the whole cycle bit calculation is now simplified and adapted to handle
event and endpoint context dequeue pointer differences.
Fixes: 1f81b6d22a59 ("usb: xhci: Prefer endpoint context dequeue pointer")
Reported-by: Maciej Puzio <mx34567@gmail.com>
Reported-by: Evan Langlois <uudruid74@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Maciej Puzio <mx34567@gmail.com>
Tested-by: Evan Langlois <uudruid74@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Streams on the EJ168 do not work as they should. I've spend 2 days trying
to get them to work, but without success.
The first problem is that when ever you ring the stream-ring doorbell, the
controller starts executing trbs at the beginning of the first ring segment,
event if it ended somewhere else previously. This can be worked around by
allowing enqueing only one td (not a problem with how streams are typically
used) and then resetting our copies of the enqueueing en dequeueing pointers
on a td completion to match what the controller seems to be doing.
This way things seem to start working with uas and instead of being able
to complete only the very first scsi command, the scsi core can probe the disk.
But then things break later on when td-s get enqueued with more then one
trb. The controller does seem to increase its dequeue pointer while executing
a stream-ring (data transfer events I inserted for debugging do trigger).
However execution seems to stop at the final normal trb of a multi trb td,
even if there is a data transfer event inserted after the final trb.
The first problem alone is a serious deviation from the spec, and esp.
dealing with cancellation would have been very tricky if not outright
impossible, but the second problem simply is a deal breaker altogether,
so this patch simply disables streams.
Note this will cause the usb-storage + uas driver pair to automatically switch
to using usb-storage instead of uas on these devices, essentially reverting
to the 3.14 and earlier behavior when uas was marked CONFIG_BROKEN.
https://bugzilla.redhat.com/show_bug.cgi?id=1121288
https://bugzilla.kernel.org/show_bug.cgi?id=80101
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
grep must work, not matter the line length.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
