| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
|
|
We accidentally take the "port->lock" twice in a row. This old code
was supposed to be deleted.
Fixes: e58e241c1788 ('sparc: serial: Clean up the locking for -rt')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the hvc driver to use the OPAL irqchip if made available by the
running firmware. If it is not present, the driver falls back to the
existing OPAL event number.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Commit 2def86a7200c ("hvc: Convert to using interrupts instead of opal
events") enabled the use of interrupts in the hvc_driver for OPAL
platforms. However on machines with more than one hvc console, any
console after the first will fail to register an interrupt handler in
notifier_add_irq() since all consoles share the same IRQ number but do
not set the IRQF_SHARED flag:
genirq: Flags mismatch irq 31. 00000000 (hvc_console) vs. 00000000 (hvc_console)
hvc_open: request_irq failed with rc -16.
This error propagates up to hvc_open() and the console is closed, but
OPAL will still generate interrupts that are not handled, leading to
rcu_sched stall warnings.
Set IRQF_SHARED when calling request_irq(), allowing additional consoles
to start properly. This is only set for consoles handled by
hvc_opal_probe(), leaving other types unaffected.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
It's a part of oom context just like allocation order and nodemask, so
let's move it to oom_control instead of passing it in the argument list.
Link: http://lkml.kernel.org/r/40e03fd7aaf1f55c75d787128d6d17c5a71226c2.1464358556.git.vdavydov@virtuozzo.com
Signed-off-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big tty and serial driver update for 4.8-rc1.
Lots of good cleanups from Jiri on a number of vt and other tty
related things, and the normal driver updates. Full details are in
the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits)
tty/serial: atmel: enforce tasklet init and termination sequences
serial: sh-sci: Stop transfers in sci_shutdown()
serial: 8250_ingenic: drop #if conditional surrounding earlycon code
serial: 8250_mtk: drop !defined(MODULE) conditional
serial: 8250_uniphier: drop !defined(MODULE) conditional
earlycon: mark earlycon code as __used iif the caller is built-in
tty/serial/8250: use mctrl_gpio helpers
serial: mctrl_gpio: enable API usage only for initialized mctrl_gpios struct
serial: mctrl_gpio: add modem control read routine
tty/serial/8250: make UART_MCR register access consistent
serial: 8250_mid: Read RX buffer on RX DMA timeout for DNV
serial: 8250_dma: Export serial8250_rx_dma_flush()
dmaengine: hsu: Export hsu_dma_get_status()
tty: serial: 8250: add CON_CONSDEV to flags
tty: serial: samsung: add byte-order aware bit functions
tty: serial: samsung: fixup accessors for endian
serial: sirf: make fifo functions static
serial: mps2-uart: make driver explicitly non-modular
serial: mvebu-uart: free the IRQ in ->shutdown()
serial/bcm63xx_uart: use correct alias naming
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A few more fixes for the input subsystem:
- restore naming for tsc2005 touchscreens as some userspace match on it
- fix out of bound access in legacy keyboard driver
- fixup in RMI4 driver
Everything is tagged for stable as well"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: tsc200x - report proper input_dev name
tty/vt/keyboard: fix OOB access in do_compute_shiftstate()
Input: synaptics-rmi4 - fix maximum size check for F12 control register 8
|
|
The size of individual keymap in drivers/tty/vt/keyboard.c is NR_KEYS,
which is currently 256, whereas number of keys/buttons in input device (and
therefor in key_down) is much larger - KEY_CNT - 768, and that can cause
out-of-bound access when we do
sym = U(key_maps[0][k]);
with large 'k'.
To fix it we should not attempt iterating beyond smaller of NR_KEYS and
KEY_CNT.
Also while at it let's switch to for_each_set_bit() instead of open-coding
it.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pinned timers must carry the pinned attribute in the timer structure
itself, so convert the code to the new API.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094341.537448301@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pinned timers must carry the pinned attribute in the timer structure
itself, so convert the code to the new API.
No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094341.456452642@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
smallest supported chip
This patch changes the compatibility string to match with the smallest
supported chip (EP7209). Since the DT-support for this CPU is not yet
announced, this change is safe.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We want the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
An ENOMEM when creating a pair tty in tty_ldisc_setup causes a null
pointer dereference in devpts_kill_index because tty->link->driver_data
is NULL. The oops was triggered with the pty stressor in stress-ng when
in a low memory condition.
tty_init_dev tries to clean up a tty_ldisc_setup ENOMEM error by calling
release_tty, however, this ultimately tries to clean up the NULL pair'd
tty in pty_unix98_remove, triggering the Oops.
Add check to pty_unix98_remove to only clean up fsi if it is not NULL.
Ooops:
[ 23.020961] Oops: 0000 [#1] SMP
[ 23.020976] Modules linked in: ppdev snd_hda_codec_generic snd_hda_intel snd_hda_codec parport_pc snd_hda_core snd_hwdep parport snd_pcm input_leds joydev snd_timer serio_raw snd soundcore i2c_piix4 mac_hid ib_iser rdma_cm iw_cm ib_cm ib_core configfs iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi autofs4 btrfs raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel qxl aes_x86_64 ttm lrw gf128mul glue_helper ablk_helper drm_kms_helper cryptd syscopyarea sysfillrect psmouse sysimgblt floppy fb_sys_fops drm pata_acpi jitterentropy_rng drbg ansi_cprng
[ 23.020978] CPU: 0 PID: 1452 Comm: stress-ng-pty Not tainted 4.7.0-rc4+ #2
[ 23.020978] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Ubuntu-1.8.2-1ubuntu1 04/01/2014
[ 23.020979] task: ffff88007ba30000 ti: ffff880078ea8000 task.ti: ffff880078ea8000
[ 23.020981] RIP: 0010:[<ffffffff813f11ff>] [<ffffffff813f11ff>] ida_remove+0x1f/0x120
[ 23.020981] RSP: 0018:ffff880078eabb60 EFLAGS: 00010a03
[ 23.020982] RAX: 4444444444444567 RBX: 0000000000000000 RCX: 000000000000001f
[ 23.020982] RDX: 000000000000014c RSI: 000000000000026f RDI: 0000000000000000
[ 23.020982] RBP: ffff880078eabb70 R08: 0000000000000004 R09: 0000000000000036
[ 23.020983] R10: 000000000000026f R11: 0000000000000000 R12: 000000000000026f
[ 23.020983] R13: 000000000000026f R14: ffff88007c944b40 R15: 000000000000026f
[ 23.020984] FS: 00007f9a2f3cc700(0000) GS:ffff88007fc00000(0000) knlGS:0000000000000000
[ 23.020984] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 23.020985] CR2: 0000000000000010 CR3: 000000006c81b000 CR4: 00000000001406f0
[ 23.020988] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 23.020988] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 23.020988] Stack:
[ 23.020989] 0000000000000000 000000000000026f ffff880078eabb90 ffffffff812a5a99
[ 23.020990] 0000000000000000 00000000fffffff4 ffff880078eabba8 ffffffff814f9cbe
[ 23.020991] ffff88007965c800 ffff880078eabbc8 ffffffff814eef43 fffffffffffffff4
[ 23.020991] Call Trace:
[ 23.021000] [<ffffffff812a5a99>] devpts_kill_index+0x29/0x50
[ 23.021002] [<ffffffff814f9cbe>] pty_unix98_remove+0x2e/0x50
[ 23.021006] [<ffffffff814eef43>] release_tty+0xb3/0x1b0
[ 23.021007] [<ffffffff814f18d4>] tty_init_dev+0xd4/0x1c0
[ 23.021011] [<ffffffff814f9fae>] ptmx_open+0xae/0x190
[ 23.021013] [<ffffffff812254ef>] chrdev_open+0xbf/0x1b0
[ 23.021015] [<ffffffff8121d973>] do_dentry_open+0x203/0x310
[ 23.021016] [<ffffffff81225430>] ? cdev_put+0x30/0x30
[ 23.021017] [<ffffffff8121ee44>] vfs_open+0x54/0x80
[ 23.021018] [<ffffffff8122b8fc>] ? may_open+0x8c/0x100
[ 23.021019] [<ffffffff8122f26b>] path_openat+0x2eb/0x1440
[ 23.021020] [<ffffffff81230534>] ? putname+0x54/0x60
[ 23.021022] [<ffffffff814f6f97>] ? n_tty_ioctl_helper+0x27/0x100
[ 23.021023] [<ffffffff81231651>] do_filp_open+0x91/0x100
[ 23.021024] [<ffffffff81230596>] ? getname_flags+0x56/0x1f0
[ 23.021026] [<ffffffff8123fc66>] ? __alloc_fd+0x46/0x190
[ 23.021027] [<ffffffff8121f1e4>] do_sys_open+0x124/0x210
[ 23.021028] [<ffffffff8121f2ee>] SyS_open+0x1e/0x20
[ 23.021035] [<ffffffff81845576>] entry_SYSCALL_64_fastpath+0x1e/0xa8
[ 23.021044] Code: 63 28 45 31 e4 eb dd 0f 1f 44 00 00 55 4c 63 d6 48 ba 89 88 88 88 88 88 88 88 4c 89 d0 b9 1f 00 00 00 48 f7 e2 48 89 e5 41 54 53 <8b> 47 10 48 89 fb 8d 3c c5 00 00 00 00 48 c1 ea 09 b8 01 00 00
[ 23.021045] RIP [<ffffffff813f11ff>] ida_remove+0x1f/0x120
[ 23.021045] RSP <ffff880078eabb60>
[ 23.021046] CR2: 0000000000000010
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As some race conditions are identified in the termination process of tasklets,
enforce the atmel_shutdown() sequence. This way we make sure that no new
tasklets or software timer are scheduled during shutdown process.
An atomic flag is positioned to give this information throughout the code.
We also remove tasklet_disable() calls that were leading to deadlocks while
stopping the driver. A simpler init/kill sequence is used.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure the transmitter and receiver are stopped when shutting down
the port, and related interrupts are disabled.
Without this:
- New input data may be received into the RX FIFO, possibly
triggering a new RX DMA completion,
- Transfers will still be enabled on a subsequent startup of the UART,
before the UART's FIFOs have been reset, causing reading of stale
data.
Inspired by a patch in the BSP by Koji Matsuoka
<koji.matsuoka.xm@renesas.com>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The #if defined(CONFIG_SERIAL_EARLYCON) && !defined(MODULE)
conditional has been added to the OF_EARLYCON_DECLARE() define.
The same conditional can be dropped from 8250_ingenic.c because
the unused symbols will be marked as __maybe_unsed.
Also, the Kconfig dependency can become much simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.
This commit partially reverts commit 3f5921a60f74 ("serial:
8250/mediatek: fix building with SERIAL_8250=m").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The !defined(MODULE) conditional has been added to the
OF_EARLYCON_DECLARE() define.
Now we can revert commit a2d3ea2f2399 ("serial: 8250/uniphier:
fix modular build").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This workaround is needed for the cases, where mctrl_gpio API is used
before mctrl_gpio_init() was invoked. This happens in 8250 during
console initialization, as the driver sets DTR signal.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
mctrl_gpio_get_outputs() returns the state of following signals:
RTS, DTR
While defining the routine for reading outputs, fix the comment for
mctrl_gpio_get() routine as it returns only the state of the input
signals.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce serial8250_out_MCR() and serial8250_in_MCR() routines, that
replace following calls:
serial_out(port, UART_MCR, val)
serial_port_out(up, UART_MCR, val)
serial_in(port, UART_MCR)
This patch is needed in order to integrate reading/writing of MCR
signals via SERIAL_MCTRL_GPIO infrastructure later.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In DNV, when RX DMA is used and number of bytes received is less than
transfer size, only RX DMA timeout interrupt is sent. When this happens,
read the RX buffer.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Export serial8250_rx_dma_flush() for use by SOC UART drivers.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To allow other code to safely read DMA Channel Status Register (where
the register attribute for Channel Error, Descriptor Time Out &
Descriptor Done fields are read-clear), export hsu_dma_get_status().
hsu_dma_irq() is renamed to hsu_dma_do_irq() and requires Status
Register value to be passed in.
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When using the 8250 as a boot console and the main console results in
messages being printed twice. The console framework will only
unregister boot consoles if a new console is registered with the
CON_CONSDEV flag set.
Set this flag for the univ8250 console to prevent double-registration.
Signed-off-by: Matthew Leach <matthew.leach@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver makes use of the __set_bit() and __clear_bit() functions.
When running under big-endian, these functions don't convert the bit
indexes when working with peripheral registers, leading to the
incorrect bits being set and cleared when running big-endian.
Add two new driver functions for setting and clearing bits that are
byte-order aware.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the serial access code to deal with kernels built for big endian
operation.
Signed-off-by: Matthew Leach <matthew@mattleach.net>
Acked-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fifo mask functions should be static as they are not
used outside of the driver. Fix the following warnings by
making them static:
drivers/tty/serial/sirfsoc_uart.h:109:5: warning: symbol 'uart_usp_ff_full_mask' was not declared. Should it be static?
drivers/tty/serial/sirfsoc_uart.h:117:5: warning: symbol 'uart_usp_ff_empty_mask' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig currently controlling compilation of mps2-uart is:
config SERIAL_MPS2_UART
bool "MPS2 UART port"
depends on ARM || COMPILE_TEST
...meaning that it currently is not being built as a module by anyone.
Follow commit 89ebc2742769 ("drivers/tty: make serial/mvebu-uart.c
explicitly non-modular") as an example of moving modular code to
non-modular:
- remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
- explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
- use arch_initcall instead of module_init and remove module_exit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As suggested by the serial port infrastructure documentation, the IRQ is
requested in ->startup(). However, it is never freed in the ->shutdown()
hook.
With simple systems that open the serial port once for all and always
have at least one process that keep the serial port opened, there was no
problem. But with a more complicated system (*cough* systemd *cough*),
the serial port is opened/closed many times, which at some point no
processes having the serial port open at all. Due to this ->startup()
gets called again, tries to request_irq() again, which fails.
Fixes: 30530791a7a0 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: <stable@vger.kernel.org>
Cc: Ofer Heifetz <oferh@marvell.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The bcm63xx_uart driver uses the of alias for determing its id. Recent
changes in dts files changed the expected 'uartX' to the recommended
'serialX', breaking serial output. Fix this by checking for a 'serialX'
alias as well.
Fixes: e3b992d028f8 ("MIPS: BMIPS: Improve BCM6328 device tree")
Fixes: 2d52ee82b475 ("MIPS: BMIPS: Improve BCM6368 device tree")
Fixes: 7537d273e2f3 ("MIPS: BMIPS: Add device tree example for BCM6358")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_M32R_SIO
drivers/tty/serial/Kconfig: bool "M32R SIO I/F"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file already has that.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_VT8500
drivers/tty/serial/Kconfig: bool "VIA VT8500 on-chip serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
We don't replace module.h with init.h since the file already has that.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Tony Prisk <linux@prisktech.co.nz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Alexey Charkov <alchark@gmail.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/tty/serial/Kconfig:config SERIAL_PXA
drivers/tty/serial/Kconfig: bool "PXA serial port support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE and MODULE_ALIAS are both a
no-op for non-modular builds.
We also delete the MODULE_LICENSE tag since that information is
already contained at the top of the file in the comments.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add COMPILE_TEST for the compilation test coverage.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch makes assignment of port line automatically,
so now user allow to use several MAX310X chips.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add uart_remove_one_port() for error path.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch moves UART registration at module_init initcall,
so this should helps to add multiple chip support in the future.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use resource managed functions devm_gpiochip_add_data() to make
error & exit path a bit simpler.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
RS485 IOCTLs uses spinlocks, so move regmap functions into a separate
work queue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Adds support for the WCH CH355 4S card in the 8250 serial driver.
Signed-off-by: Alexandr Petrenko <petrenkoas83@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On non-DeviceTree platforms, the index of serial device is a static
variable incremented on each probe. It is incremented even if deferred
probe happens when getting the clock in s3c24xx_serial_init_port().
This index is used for referencing elements of statically allocated
s3c24xx_serial_ports array. In case of re-probe, the index will point
outside of this array leading to memory corruption.
Increment the index only on successful probe.
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Fixes: b497549a035c ("[ARM] S3C24XX: Split serial driver into core and per-cpu drivers")
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the clk_get() of "uart" clock returns EPROBE_DEFER, the next re-probe
finishes with success but uses invalid (ERR_PTR) values. This leads to
dereferencing of ERR_PTR stored under ourport->clk:
12c30000.serial: Controller clock not found
(...)
12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
Unable to handle kernel paging request at virtual address fffffdfb
(clk_prepare) from [<c039f7d0>] (s3c24xx_serial_pm+0x20/0x128)
(s3c24xx_serial_pm) from [<c0395414>] (uart_change_pm+0x38/0x40)
(uart_change_pm) from [<c039689c>] (uart_add_one_port+0x31c/0x44c)
(uart_add_one_port) from [<c03a035c>] (s3c24xx_serial_probe+0x2a8/0x418)
(s3c24xx_serial_probe) from [<c03ee110>] (platform_drv_probe+0x50/0xb0)
(platform_drv_probe) from [<c03ecb44>] (driver_probe_device+0x1f4/0x2b0)
(driver_probe_device) from [<c03eb0c0>] (bus_for_each_drv+0x44/0x8c)
(bus_for_each_drv) from [<c03ec8c8>] (__device_attach+0x9c/0x100)
(__device_attach) from [<c03ebf54>] (bus_probe_device+0x84/0x8c)
(bus_probe_device) from [<c03ec388>] (deferred_probe_work_func+0x60/0x8c)
(deferred_probe_work_func) from [<c012fee4>] (process_one_work+0x120/0x328)
(process_one_work) from [<c0130150>] (worker_thread+0x2c/0x4ac)
(worker_thread) from [<c0135320>] (kthread+0xd8/0xf4)
(kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
The first unsuccessful clk_get() causes s3c24xx_serial_init_port() to
exit with failure but the s3c24xx_uart_port is left half-configured
(e.g. port->mapbase is set, clk contains ERR_PTR). On next re-probe,
the function s3c24xx_serial_init_port() will exit early with success
because of configured port->mapbase and driver will use old values,
including the ERR_PTR as clock.
Fix this by cleaning the port->mapbase on error path so each re-probe
will initialize all of the port settings.
Fixes: 60e93575476f ("serial: samsung: enable clock before clearing pending interrupts during init")
Cc: <stable@vger.kernel.org>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some BIOS only use _OSI("Linux") to distinguish between Linux & Windows.
Apply Level/Low to UART trigger mode if Windows, Edge/High mode otherwise.
But since 2.6.23 the mainline kernel no longer returns true for
_OSI(“Linux”).
The default IRQ0~15 trigger mode in Linux is Edge/High mode without
ACPI MADT override. It mismatches IRQ mode and makes UART malfunctional on
such motherboard.
This patch will check the current IRQ mode and apply correct mode to UART.
The following link is F81216AD spec PDF:
http://html.alldatasheet.com/html-pdf/257956/FINTEK/F81216AD/5569/
25/F81216AD.html
LDN0~3
70h: IRQ channel & Mode register
Bit 6~5 :
00 : Active low level mode
01 : Active high edge mode
Bit 4 : Sharing Flag (0: not share/1: share)
Bit 3~0 : IRQ channel
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Allocated memory for 'sport->irq_fault_name' is freed twice, first
in error check of 'if(!sport->irq_rx_name)' and other in fallback
handler.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently the clocks are enabled at probe and disabled
at remove. Instead enable the clocks when used.
Signed-off-by: Shubhrajyoti Datta <shubhraj@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
