| Age | Commit message (Collapse) | Author |
|---|
|
Maximilian reported that surface_serial_hub serdev tx does not work during
system suspend. During system suspend, runtime PM gets disabled in
__device_suspend_late(), and tx is unable to wake-up the serial core port
device that we use to check if tx is safe to start. Johan summarized the
regression noting that serdev tx no longer always works as earlier when the
serdev device is runtime PM active.
The serdev device and the serial core controller devices are siblings of
the serial port hardware device. The runtime PM usage count from serdev
device does not propagate to the serial core device siblings, it only
propagates to the parent.
In addition to the tx issue for suspend, testing for the serial core port
device can cause an unnecessary delay in enabling tx while waiting for the
serial core port device to wake-up. The serial core port device wake-up is
only needed to flush pending tx when the serial port hardware device was
in runtime PM suspended state.
To fix the regression, we need to check the runtime PM state of the parent
serial port hardware device for tx instead of the serial core port device.
As the serial port device drivers may or may not implement runtime PM, we
need to also add a check for pm_runtime_enabled().
Reported-by: Maximilian Luz <luzmaximilian@gmail.com>
Cc: stable <stable@kernel.org>
Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Maximilian Luz <luzmaximilian@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20231005075644.25936-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We now get errors on system suspend if no_console_suspend is set as
reported by Thomas. The errors started with commit 20a41a62618d ("serial:
8250_omap: Use force_suspend and resume for system suspend").
Let's fix the issue by checking for console_suspend_enabled in the system
suspend and resume path.
Note that with this fix the checks for console_suspend_enabled in
omap8250_runtime_suspend() become useless. We now keep runtime PM usage
count for an attached kernel console starting with commit bedb404e91bb
("serial: 8250_port: Don't use power management for kernel console").
Fixes: 20a41a62618d ("serial: 8250_omap: Use force_suspend and resume for system suspend")
Cc: stable <stable@kernel.org>
Cc: Udit Kumar <u-kumar1@ti.com>
Reported-by: Thomas Richard <thomas.richard@bootlin.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20230926061319.15140-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 44b27aec9d96 ("serial: core, 8250: set RS485 termination GPIO in
serial core") enabled support for RS485 termination GPIOs behind i2c
expanders by setting the GPIO outside of the critical section protected
by the port spinlock. Access to the i2c expander may sleep, which
caused a splat with the port spinlock held.
Commit 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in
driver-specific way") erroneously regressed that by spinlocking the
GPIO manipulation again.
Fix by moving uart_rs485_config() (the function manipulating the GPIO)
outside of the spinlocked section and acquiring the spinlock inside of
uart_rs485_config() for the invocation of ->rs485_config() only.
This gets us one step closer to pushing the spinlock down into the
->rs485_config() callbacks which actually need it. (Some callbacks
do not want to be spinlocked because they perform sleepable register
accesses, see e.g. sc16is7xx_config_rs485().)
Stack trace for posterity:
Voluntary context switch within RCU read-side critical section!
WARNING: CPU: 0 PID: 56 at kernel/rcu/tree_plugin.h:318 rcu_note_context_switch
Call trace:
rcu_note_context_switch
__schedule
schedule
schedule_timeout
wait_for_completion_timeout
bcm2835_i2c_xfer
__i2c_transfer
i2c_transfer
i2c_transfer_buffer_flags
regmap_i2c_write
_regmap_raw_write_impl
_regmap_bus_raw_write
_regmap_write
_regmap_update_bits
regmap_update_bits_base
pca953x_gpio_set_value
gpiod_set_raw_value_commit
gpiod_set_value_nocheck
gpiod_set_value_cansleep
uart_rs485_config
uart_add_one_port
pl011_register_port
pl011_probe
Fixes: 7c7f9bc986e6 ("serial: Deassert Transmit Enable on probe in driver-specific way")
Suggested-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v6.1+
Link: https://lore.kernel.org/r/f3a35967c28b32f3c6432d0aa5936e6a9908282d.1695307688.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case the leaf driver wants to use IRQ polling (irq = 0) and
IIR register shows that an interrupt happened in the 8250 hardware
the IRQ data can be NULL. In such a case we need to skip the wake
event as we came to this path from the timer interrupt and quite
likely system is already awake.
Without this fix we have got an Oops:
serial8250: ttyS0 at I/O 0x3f8 (irq = 0, base_baud = 115200) is a 16550A
...
BUG: kernel NULL pointer dereference, address: 0000000000000010
RIP: 0010:serial8250_handle_irq+0x7c/0x240
Call Trace:
? serial8250_handle_irq+0x7c/0x240
? __pfx_serial8250_timeout+0x10/0x10
Fixes: 0ba9e3a13c6a ("serial: 8250: Add missing wakeup event reporting")
Cc: stable <stable@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20230831222555.614426-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty and serial driver changes for 6.6-rc1.
Lots of cleanups in here this cycle, and some driver updates. Short
summary is:
- Jiri's continued work to make the tty code and apis be a bit more
sane with regards to modern kernel coding style and types
- cpm_uart driver updates
- n_gsm updates and fixes
- meson driver updates
- sc16is7xx driver updates
- 8250 driver updates for different hardware types
- qcom-geni driver fixes
- tegra serial driver change
- stm32 driver updates
- synclink_gt driver cleanups
- tty structure size reduction
All of these have been in linux-next this week with no reported
issues. The last bit of cleanups from Jiri and the tty structure size
reduction came in last week, a bit late but as they were just style
changes and size reductions, I figured they should get into this merge
cycle so that others can work on top of them with no merge conflicts"
* tag 'tty-6.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (199 commits)
tty: shrink the size of struct tty_struct by 40 bytes
tty: n_tty: deduplicate copy code in n_tty_receive_buf_real_raw()
tty: n_tty: extract ECHO_OP processing to a separate function
tty: n_tty: unify counts to size_t
tty: n_tty: use u8 for chars and flags
tty: n_tty: simplify chars_in_buffer()
tty: n_tty: remove unsigned char casts from character constants
tty: n_tty: move newline handling to a separate function
tty: n_tty: move canon handling to a separate function
tty: n_tty: use MASK() for masking out size bits
tty: n_tty: make n_tty_data::num_overrun unsigned
tty: n_tty: use time_is_before_jiffies() in n_tty_receive_overrun()
tty: n_tty: use 'num' for writes' counts
tty: n_tty: use output character directly
tty: n_tty: make flow of n_tty_receive_buf_common() a bool
Revert "tty: serial: meson: Add a earlycon for the T7 SoC"
Documentation: devices.txt: Fix minors for ttyCPM*
Documentation: devices.txt: Remove ttySIOC*
Documentation: devices.txt: Remove ttyIOC*
serial: 8250_bcm7271: improve bcm7271 8250 port
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
- An extensive rework of kexec and crash Kconfig from Eric DeVolder
("refactor Kconfig to consolidate KEXEC and CRASH options")
- kernel.h slimming work from Andy Shevchenko ("kernel.h: Split out a
couple of macros to args.h")
- gdb feature work from Kuan-Ying Lee ("Add GDB memory helper
commands")
- vsprintf inclusion rationalization from Andy Shevchenko
("lib/vsprintf: Rework header inclusions")
- Switch the handling of kdump from a udev scheme to in-kernel
handling, by Eric DeVolder ("crash: Kernel handling of CPU and memory
hot un/plug")
- Many singleton patches to various parts of the tree
* tag 'mm-nonmm-stable-2023-08-28-22-48' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (81 commits)
document while_each_thread(), change first_tid() to use for_each_thread()
drivers/char/mem.c: shrink character device's devlist[] array
x86/crash: optimize CPU changes
crash: change crash_prepare_elf64_headers() to for_each_possible_cpu()
crash: hotplug support for kexec_load()
x86/crash: add x86 crash hotplug support
crash: memory and CPU hotplug sysfs attributes
kexec: exclude elfcorehdr from the segment digest
crash: add generic infrastructure for crash hotplug support
crash: move a few code bits to setup support of crash hotplug
kstrtox: consistently use _tolower()
kill do_each_thread()
nilfs2: fix WARNING in mark_buffer_dirty due to discarded buffer reuse
scripts/bloat-o-meter: count weak symbol sizes
treewide: drop CONFIG_EMBEDDED
lockdep: fix static memory detection even more
lib/vsprintf: declare no_hash_pointers in sprintf.h
lib/vsprintf: split out sprintf() and friends
kernel/fork: stop playing lockless games for exe_file replacement
adfs: delete unused "union adfs_dirtail" definition
...
|
|
This reverts commit 6a4197f9763325043abf7690a21124a9facbf52e
New SoC will use ttyS0 instead of ttyAML, so T7 SoC doesn't need a
OF_EARLYCON_DECLARE.
Fixes: 6a4197f97633 ("tty: serial: meson: Add a earlycon for the T7 SoC")
Signed-off-by: Lucas Tanure <tanure@linux.com>
Link: https://lore.kernel.org/r/20230827082944.5100-1-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 8250 BCM7271 UART is not a direct match to PORT_16550A and other
generic ports do not match its hardware capabilities. PORT_ALTR matches
the rx trigger levels, but its vendor configurations are not compatible.
Unfortunately this means we need to create another port to fully capture
the hardware capabilities of the BCM7271 UART.
To alleviate some latency pressures, we default the rx trigger level to 8.
Signed-off-by: Justin Chen <justin.chen@broadcom.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Acked-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/1692643978-16570-1-git-send-email-justin.chen@broadcom.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Retrieve rs485 devicetree properties on registration of sc16is7xx ports in
case they are attached to an rs485 transceiver.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-7-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When configuring a pin as an output pin with a value of logic 0, we
end up as having a value of logic 1 on the output pin. Setting a
logic 0 a second time (or more) after that will correctly output a
logic 0 on the output pin.
By default, all GPIO pins are configured as inputs. When we enter
sc16is7xx_gpio_direction_output() for the first time, we first set the
desired value in IOSTATE, and then we configure the pin as an output.
The datasheet states that writing to IOSTATE register will trigger a
transfer of the value to the I/O pin configured as output, so if the
pin is configured as an input, nothing will be transferred.
Therefore, set the direction first in IODIR, and then set the desired
value in IOSTATE.
This is what is done in NXP application note AN10587.
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-6-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 679875d1d880 ("sc16is7xx: Separate GPIOs from modem control lines")
and commit 21144bab4f11 ("sc16is7xx: Handle modem status lines")
changed the function of the GPIOs pins to act as modem control
lines without any possibility of selecting GPIO function.
As a consequence, applications that depends on GPIO lines configured
by default as GPIO pins no longer work as expected.
Also, the change to select modem control lines function was done only
for channel A of dual UART variants (752/762). This was not documented
in the log message.
Allow to specify GPIO or modem control line function in the device
tree, and for each of the ports (A or B).
Do so by using the new device-tree property named
"nxp,modem-control-line-ports" (property added in separate patch).
When registering GPIO chip controller, mask-out GPIO pins declared as
modem control lines according to this new DT property.
Fixes: 679875d1d880 ("sc16is7xx: Separate GPIOs from modem control lines")
Fixes: 21144bab4f11 ("sc16is7xx: Handle modem status lines")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230807214556.540627-5-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit c8f71b49ee4d ("serial: sc16is7xx: setup GPIO controller later
in probe") moved GPIO setup code later in probe function. Doing so
also required to move ports cleanup code (out_ports label) after the
GPIO cleanup code.
After these moves, the out_thread label becomes misplaced and makes
part of the cleanup code illogical.
This patch remove the now obsolete out_thread label and make GPIO
setup code jump to out_ports label if it fails.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20230807214556.540627-3-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sc16is7xx_config_rs485() function is called only for the second
port (index 1, channel B), causing initialization problems for the
first port.
For the sc16is7xx driver, port->membase and port->mapbase are not set,
and their default values are 0. And we set port->iobase to the device
index. This means that when the first device is registered using the
uart_add_one_port() function, the following values will be in the port
structure:
port->membase = 0
port->mapbase = 0
port->iobase = 0
Therefore, the function uart_configure_port() in serial_core.c will
exit early because of the following check:
/*
* If there isn't a port here, don't do anything further.
*/
if (!port->iobase && !port->mapbase && !port->membase)
return;
Typically, I2C and SPI drivers do not set port->membase and
port->mapbase.
The max310x driver sets port->membase to ~0 (all ones). By
implementing the same change in this driver, uart_configure_port() is
now correctly executed for all ports.
Fixes: dfeae619d781 ("serial: sc16is7xx")
Cc: stable@vger.kernel.org
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Reviewed-by: Lech Perczak <lech.perczak@camlingroup.com>
Tested-by: Lech Perczak <lech.perczak@camlingroup.com>
Link: https://lore.kernel.org/r/20230807214556.540627-2-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When there's no irq(this can be due to various reasons, for example,
no irq from HW support, or we just want to use poll solution, and so
on), falling back to poll is still better than no support at all.
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Link: https://lore.kernel.org/r/20230806092056.2467-3-jszhang@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In tegra_uart_hw_init(), the return value of clk_prepare_enable() should
be checked since it might fail.
Fixes: e9ea096dd225 ("serial: tegra: add serial driver")
Signed-off-by: Yi Yang <yiyang13@huawei.com>
Link: https://lore.kernel.org/r/20230817105406.228674-1-yiyang13@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If the Sifive Uart is not used as the wake up source, suspend the uart
before the system enter the suspend state to prevent it woken up by
unexpected uart interrupt. Resume the uart once the system woken up.
Signed-off-by: Nick Hu <nick.hu@sifive.com>
Reviewed-by: Ben Dooks <ben.dooks@codethink.co.uk>
Link: https://lore.kernel.org/r/20230815090216.2575971-1-nick.hu@sifive.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The new Amlogic T7 SoC does not have a always-on uart,
so add OF_EARLYCON_DECLARE for it.
Signed-off-by: Lucas Tanure <tanure@linux.com>
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230814080128.143613-2-tanure@linux.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In shutdown, RX DMA channel is terminated. If the DMA RX callback is
scheduled but not yet executed, while a new RX DMA transfer is started, the
callback can be executed, and then disturb the ongoing RX DMA transfer.
To avoid such a case, call dmaengine_synchronize in shutdown, after the
DMA RX channel is terminated.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-7-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
Create two new functions (stm32_usart_rx_dma_pause, stm32_usart_rx_dma
_resume) to handle dma error when pausing/resuming.
And rename stm32_usart_start_rx_dma_cyclic() to
stm32_usart_rx_dma_start_or_resume() and use this function to resume an
rx dma transfer. If resume fail, stm32_usart_rx_dma_start_or_resume can
create a new transfer to continue.
It is also safer to close DMA before reset DMAR in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-6-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Create new function "stm32_usart_dma_pause_resume" that called dmaengine_
pause/resume and in case of error, terminate dma transaction.
Two other functions are created to facilitate the use of stm32_usart_dma
_pause_resume : stm32_usart_tx_dma_pause, stm32_usart_tx_dma_resume.
Equivalent functions for rx will be added in future patch.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-5-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Rename stm32_usart_rx_dma_enabled to stm32_usart_rx_dma_started in order
to match with stm32_usart_tx_dma_started.
Modify argument of stm32_usart_rx_dma_started from uart_port structure to
stm32_port structure to match with stm32_usart_tx_dma_started.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-4-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DMAT is a configuration bit so it should be set at the startup of uart
port and not when a DMA transfer begins.
This patch move set of DMAT into set_termios and remove DMAT reset except
in shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's rather advised to rely on DMA pause / resume instead of
clearing/setting DMA request enable bit for the same purpose. Some DMA
request/acknowledge race may encountered by doing so. We prefer to use
dmaengine_pause and resume instead to pause a dma transfer when it is
necessary.
It is also safer to close DMA before reset DMAT in stm32_usart_shutdown.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20230808161906.178996-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty") into tty-next
We need the serial-core fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
abs_diff() belongs to math.h. Move it there. This will allow others to
use it.
[andriy.shevchenko@linux.intel.com: add abs_diff() documentation]
Link: https://lkml.kernel.org/r/20230804050934.83223-1-andriy.shevchenko@linux.intel.com
[akpm@linux-foundation.org: fix comment, per Randy]
Link: https://lkml.kernel.org/r/20230803131918.53727-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org> # tty/serial
Acked-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> # gpu/ipu-v3
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@gmail.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
We want to fix the serial core port DEVNAME to use a port id of the
hardware specific controller port instance instead of the port->line.
For example, the 8250 driver sets up a number of serial8250 ports
initially that can be inherited by the hardware specific driver. At that
the port->line no longer decribes the port's relation to the serial core
controller instance.
Let's fix the issue by assigning port->port_id for each serial core
controller port instance.
Fixes: 7d695d83767c ("serial: core: Fix serial_base_match() after fixing controller port name")
Tested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230811103648.2826-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port lock is not always held when calling serial8250_clear_IER().
When an oops is in progress, the lock is tried to be taken and when it
is not, a warning is issued:
WARNING: CPU: 0 PID: 1 at drivers/tty/serial/8250/8250_port.c:707 +0x57/0x60
Modules linked in:
CPU: 0 PID: 1 Comm: init Not tainted 6.5.0-rc5-1.g225bfb7-default+ #774 00f1be860db663ed29479b8255d3b01ab1135bd3
Hardware name: QEMU Standard PC ...
RIP: 0010:serial8250_clear_IER+0x57/0x60
...
Call Trace:
<TASK>
serial8250_console_write+0x9e/0x4b0
console_flush_all+0x217/0x5f0
...
Therefore, remove the annotation as it doesn't hold for all invocations.
The other option would be to make the lockdep test conditional on
'oops_in_progress' or pass 'locked' from serial8250_console_write(). I
don't think, that is worth it.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Reported-by: Vlastimil Babka <vbabka@suse.cz>
Cc: John Ogness <john.ogness@linutronix.de>
Fixes: d0b309a5d3f4 (serial: 8250: synchronize and annotate UART_IER access)
Link: https://lore.kernel.org/r/20230811064340.13400-1-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unify with the rest of the code. Use size_t for counts and ssize_t for
retval.
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20230810091510.13006-30-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Data are now typed as u8. Propagate this change to
tty_operations::put_char().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Link: https://lore.kernel.org/r/20230810091510.13006-29-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Data are now typed as u8. Propagate this change to
tty_operations::write().
Signed-off-by: "Jiri Slaby (SUSE)" <jirislaby@kernel.org>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Jens Taprogge <jens.taprogge@taprogge.org>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Scott Branden <scott.branden@broadcom.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: David Sterba <dsterba@suse.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
Link: https://lore.kernel.org/r/20230810091510.13006-28-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
TX is handled by primary sequencer. After cancelling primary command, poll
primary sequencer's irq status instead of that of secondary.
While at it, also remove a couple of redundant lines that read from IRQ_EN
register and write back same.
Fixes: 2aaa43c70778 ("tty: serial: qcom-geni-serial: add support for serial engine DMA")
Signed-off-by: Vijaya Krishna Nivarthi <quic_vnivarth@quicinc.com>
Link: https://lore.kernel.org/r/1691578393-9891-1-git-send-email-quic_vnivarth@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver depends on CONFIG_OF, it is not necessary to use
of_match_ptr() here.
Signed-off-by: Ruan Jinjie <ruanjinjie@huawei.com>
Link: https://lore.kernel.org/r/20230809085541.2969654-1-ruanjinjie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Guenter reports boot issues with duplicate sysfs entries for multiport
drivers. Let's go back to using port->line for now to fix the regression.
With this change, the serial core port device names are not correct for the
hardware specific 8250 single port drivers, but that's a cosmetic issue for
now.
Fixes: d962de6ae51f ("serial: core: Fix serial core port id to not use port->line")
Reported-by: Guenter Roeck <groeck7@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230806062052.47737-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unloading a hardware specific 8250 driver can produce error "Unable to
handle kernel paging request at virtual address" about ten seconds after
unloading the driver. This happens on uart_hangup() calling
uart_change_pm().
Turns out commit 04e82793f068 ("serial: 8250: Reinit port->pm on port
specific driver unbind") was only a partial fix. If the hardware specific
driver has initialized port->pm function, we need to clear port->pm too.
Just reinitializing port->ops does not do this. Otherwise serial8250_pm()
will call port->pm() instead of serial8250_do_pm().
Fixes: 04e82793f068 ("serial: 8250: Reinit port->pm on port specific driver unbind")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804131553.52927-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After fixing the serial core port device to use port->port_id instead of
port->line, unloading a hardware specific 8250 port driver started
producing an error for "sysfs: cannot create duplicate filename".
This is happening as we are wrongly initializing port->port_id to zero
when adding back serial8250_isa_devs instances, and the serial8250:0.0
sysfs entry may already exist. For serial8250 devices, we typically have
multiple devices mapped to a single driver instance. For the
serial8250_isa_devs instances, the port->port_id is the same as port->line.
Let's fix the issue by re-initializing port_id when adding back the
serial8250_isa_devs instances in serial8250_unregister_port().
Fixes: d962de6ae51f ("serial: core: Fix serial core port id to not use port->line")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20230804123546.25293-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Kmemleak reports issues for serial8250 ports after the hardware specific
driver takes over on boot as noted by Tomi.
The kerneldoc for device_initialize() says we must call device_put()
after calling device_initialize(). We are calling device_put() on the
error path, but are missing it from the device remove path. This causes
release() to never get called for the devices on remove.
Let's add the missing put_device() calls for both serial ctrl and
port devices.
Fixes: 84a9582fd203 ("serial: core: Start managing serial controllers to enable runtime PM")
Reported-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Link: https://lore.kernel.org/r/20230804090909.51529-1-tony@atomide.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixes following sparse warning:
drivers/tty/serial/8250/8250_men_mcb.c:92:21: sparse: cast removes
address space '__iomem' of expression
drivers/tty/serial/8250/8250_men_mcb.c:92:21: sparse: incorrect type
in argument 1 (different address spaces) expected void const volatile
[noderef] __iomem *addr got void *
Fixes: 2554e6ba28a2 ("8250_men_mcb: Read num ports from register data.")
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202307261517.x1O9OAkd-lkp@intel.com/
Signed-off-by: Jorge Sanjuan Garcia <jorge.sanjuangarcia@duagon.com>
Link: https://lore.kernel.org/r/20230803095816.110864-1-jorge.sanjuangarcia@duagon.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove inclusion of fs_uart_pd.h from all files not using
anything from that file.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/c7996ef4de56e7ee42a434e37d214cba337a146c.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cpm_uart/ subdirectory only has cpm_uart_core.c and cpm_uart.h now.
Move them up and remove cpm_uart/ directory while renaming
cpm_uart_core.c as cpm_uart.c
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/9b8b8f89fc386480030f5339abe307541ae436a6.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cpm_uart_map_pram() and cpm_uart_unmap_pram() are very
similar for CPM1 and CPM2.
On CPM1 cpm_uart_map_pram() uses of_iomap() while CPM2 uses
of_address_to_resource()/ioremap(). CPM2 version will also
work on CPM1.
On CPM2 cpm_uart_map_pram() and cpm_uart_unmap_pram() has a special
handling for SMC. Just gate it by an IS_ENABLED(CONFIG_CPM2).
So move the CPM2 version into cpm_uart_core.c which is the only
user of those two fonctions and refactor to also handle CPM1 as
mentionned above.
PROFF_SMC_SIZE is only defined for SMC2 and used only there. To make
it simple, just use the numerical value 64, this is the only place
it is used and anyway there's already the same numerical value for
the alignment.
Use cpm_muram_alloc() instead of cpm_dpalloc() macro.
Then cpm_uart_cpm1.c and cpm_uart_cpm2.c are now empty and go away.
Replace printk(KERN_WARN by pr_warn( to make checkpatch happier.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/44a266106c421319aa8e700c2db52d5dcd652c0f.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cpm_uart_freebuf() is identical for CPM1 and CPM2.
cpm_uart_allocbuf() only has a small difference between CPM1 and CPM2
as shown below:
CPM1:
if (is_con) {
/* was hostalloc but changed cause it blows away the */
/* large tlb mapping when pinning the kernel area */
mem_addr = (u8 *) cpm_dpram_addr(cpm_dpalloc(memsz, 8));
dma_addr = (u32)cpm_dpram_phys(mem_addr);
} else
mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
GFP_KERNEL);
CPM2:
if (is_con) {
mem_addr = kzalloc(memsz, GFP_NOWAIT);
dma_addr = virt_to_bus(mem_addr);
}
else
mem_addr = dma_alloc_coherent(pinfo->port.dev, memsz, &dma_addr,
GFP_KERNEL);
Refactor this by using IS_ENABLED(CONFIG_CPM1)
and move both functions in cpm_uart_core.c as they are used only there.
While doing this, add the necessary casts to silence sparse for the CPM1
part. This is because a dma alloc is not expected to be an iomem but
for CPM1 as we use DPRAM this is seen as iomem.
Also replace calls to cpm_dpxxxx() by relevant cpm_muram_xxxx() calls.
This is needed at least for cpm_dpram_phys() which is only defined
for CPM1. Just do the same for all so that cpm_dpxxxx() macros can get
droped in the future.
To silence checkpatch, replace printk(KERN_ERR by pr_err( and display
function name instead of hard coded filename. Also replace
mem_addr == NULL by !mem_addr.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/606dfdd258a4f2f2882e2e189bef37526bb3b499.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cpm_line_cr_cmd() is identical for CPM1 and CPM2 and
is used only in cpm_uart_core.c. Move it there.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/6996e6ff93067dcddebf0d0c86487345149e165c.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CPMFCR_EB is the same as SMC_EB and is defined
for both CPM1 and CPM2.
CPMFCR_GBL is defined as 0 for CPM1.
Therefore the CPM2 version of cpm_set_scc_fcr() and
cpm_set_smc_fcr() can be used on both CPM1 and CPM2.
And cpm_set_brg() is already identical and just a
wrapper of cpm_setbrg().
In addition those three fonctions are only called once
from cpm_uart_core.c, so just replace the calls with
the content of the CPM2 versions of them.
And DPRAM_BASE is identical so can go in cpm_uart.h. While
moving it, use cpm_muram_addr() directly instead of the
cpm_dpram_addr() macro and remove __force tag which isn't needed.
Then cpm_uart_cpm1.h and cpm_uart_cpm2.h go away.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/6920e61fd362961ae1aeda897c8bfe1efacdc9dc.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uart_baudrate() is just a trivial wrapper to get_baudrate().
Use get_baudrate() directly and remove assignment in if condition.
And also remove uart_clock() which is not used since
commit 0b2a2e5b7747 ("cpm_uart: Remove !CONFIG_PPC_CPM_NEW_BINDING
code")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/4d497386f576a3df768e44a04f9bb512e424c311.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using an enum indirection to define numeric macros is
pointless. Directly use the wanted numeric value.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/4772d2a21894db443fe42836421eb22206a334aa.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cpm_uart_init_portdesc()
smc1_lineif()
smc2_lineif()
scc1_lineif()
scc2_lineif()
scc3_lineif()
scc4_lineif()
Those functions were removed by commit 0b2a2e5b7747 ("cpm_uart: Remove
!CONFIG_PPC_CPM_NEW_BINDING code"). Remove stale prototypes.
UART_SMC{1..2} and UART_SCC{1..4} and SCC_WAIT_CLOSING macros are not
used anymore since the above commit.
cpm_uart_ports[] isn't used outside cpm_uart_core.c since the
same commit, so make it static.
cpm_uart_init_smc() and cpm_uart_init_scc() don't need a forward
declaration.
FLAG_DISCARDING and IS_DISCARDING have never been used since at
least 2.6.12 and the start of git repository for kernel.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/96ef20ae1df056d1b7967871ba6e27e5b5aaeea6.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CHECK drivers/tty/serial/cpm_uart/cpm_uart_core.c
drivers/tty/serial/cpm_uart/cpm_uart_core.c:1271:39: warning: context imbalance in 'cpm_uart_console_write' - unexpected unlock
Allthough 'nolock' is not expected to change, sparse find the following
form suspicious:
if (unlikely(nolock)) {
local_irq_save(flags);
} else {
spin_lock_irqsave(&pinfo->port.lock, flags);
}
cpm_uart_early_write(pinfo, s, count, true);
if (unlikely(nolock)) {
local_irq_restore(flags);
} else {
spin_unlock_irqrestore(&pinfo->port.lock, flags);
}
Rewrite it a more obvious form:
if (unlikely(oops_in_progress)) {
local_irq_save(flags);
cpm_uart_early_write(pinfo, s, count, true);
local_irq_restore(flags);
} else {
spin_lock_irqsave(&pinfo->port.lock, flags);
cpm_uart_early_write(pinfo, s, count, true);
spin_unlock_irqrestore(&pinfo->port.lock, flags);
}
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/f7da5cdc9287960185829cfef681a7d8614efa1f.1691068700.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The module_mcb_driver() will set "THIS_MODULE" to driver.owner when
register a mcb_driver driver, so it is redundant initialization to set
driver.owner in mcb_driver statement. Remove it for clean code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Link: https://lore.kernel.org/r/20230804100843.100348-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a warning reported by coccinelle:
./drivers/tty/serial/8250/8250_men_mcb.c:226:6-19: WARNING:
Unsigned expression compared with zero: data -> line [ i ] < 0
The array "line" of serial_8250_men_mcb_data is used to record the
registered serial port. When register a port failed, it will return
an error code, but the type of "line" is "unsigned int", causing
the error code to reverse. Modify the type of "data -> line" to solve
this problem.
Fixes: 2554e6ba28a2 ("8250_men_mcb: Read num ports from register data.")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230803142053.1308926-1-lizetao1@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
cotroller -> controller.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Link: https://lore.kernel.org/r/20230803175931.981625-1-hugo@hugovil.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
