| Age | Commit message (Collapse) | Author |
|---|
|
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Prevent incrementing device->commands_outstanding for ioaccel command
retries that are driver initiated. If the command goes through the retry
path, the device->commands_outstanding counter has already accounted for
the number of commands outstanding to the device. Only commands going
through function hpsa_cmd_resolve_events decrement this counter.
- ioaccel commands go to either HBA disks or to logical volumes comprised
of SSDs.
The extra increment is causing device resets to hang.
- Resets wait for all device outstanding commands to complete before
returning.
Replace unused field abort_pending with retry_pending. This is a
maintenance driver so these changes have the least impact/risk.
Link: https://lore.kernel.org/r/161342801747.29388.13045495968308188518.stgit@brunhilda
Tested-by: Joe Szczypek <jszczype@redhat.com>
Reviewed-by: Scott Benesh <scott.benesh@microchip.com>
Reviewed-by: Scott Teel <scott.teel@microchip.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
COMMAND_COMPLETE is defined as '0', and it is a SCSI parallel message to
boot. Drop the call to set_msg_byte().
Link: https://lore.kernel.org/r/20210113090500.129644-17-hare@suse.de
Reviewed-by: Christoph Hellwig <hch@lst.de>
Acked-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"This consists of the usual driver updates (ufs, qla2xxx, smartpqi,
target, zfcp, fnic, mpt3sas, ibmvfc) plus a load of cleanups, a major
power management rework and a load of assorted minor updates.
There are a few core updates (formatting fixes being the big one) but
nothing major this cycle"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (279 commits)
scsi: mpt3sas: Update driver version to 36.100.00.00
scsi: mpt3sas: Handle trigger page after firmware update
scsi: mpt3sas: Add persistent MPI trigger page
scsi: mpt3sas: Add persistent SCSI sense trigger page
scsi: mpt3sas: Add persistent Event trigger page
scsi: mpt3sas: Add persistent Master trigger page
scsi: mpt3sas: Add persistent trigger pages support
scsi: mpt3sas: Sync time periodically between driver and firmware
scsi: qla2xxx: Update version to 10.02.00.104-k
scsi: qla2xxx: Fix device loss on 4G and older HBAs
scsi: qla2xxx: If fcport is undergoing deletion complete I/O with retry
scsi: qla2xxx: Fix the call trace for flush workqueue
scsi: qla2xxx: Fix flash update in 28XX adapters on big endian machines
scsi: qla2xxx: Handle aborts correctly for port undergoing deletion
scsi: qla2xxx: Fix N2N and NVMe connect retry failure
scsi: qla2xxx: Fix FW initialization error on big endian machines
scsi: qla2xxx: Fix crash during driver load on big endian machines
scsi: qla2xxx: Fix compilation issue in PPC systems
scsi: qla2xxx: Don't check for fw_started while posting NVMe command
scsi: qla2xxx: Tear down session if FW say it is down
...
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
Link: https://lore.kernel.org/r/20201102164730.324035-21-vaibhavgupta40@gmail.com
Acked-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/scsi/hpsa.c: In function ‘hpsa_volume_offline’:
drivers/scsi/hpsa.c:3885:5: warning: variable ‘scsi_status’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c:3884:6: warning: variable ‘cmd_status’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c: In function ‘hpsa_update_scsi_devices’:
drivers/scsi/hpsa.c:4354:9: warning: variable ‘n_ext_target_devs’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c: In function ‘hpsa_scatter_gather’:
drivers/scsi/hpsa.c:4583:36: warning: variable ‘last_sg’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c: In function ‘hpsa_init_one’:
drivers/scsi/hpsa.c:8639:6: warning: variable ‘dac’ set but not used [-Wunused-but-set-variable]
drivers/scsi/hpsa.c: In function ‘hpsa_enter_performant_mode’:
drivers/scsi/hpsa.c:9300:7: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable]
Link: https://lore.kernel.org/r/20201112101929.GC1997862@dell
Cc: Don Brace <don.brace@microchip.com>
Cc: Bugfixes to <esc.storagedev@microsemi.com>
Cc: storagedev@microchip.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When hpsa_scsi_add_host() fails, h->lastlogicals is leaked since it is
missing a free() in the error handler.
Fix this by adding free() when hpsa_scsi_add_host() fails.
Link: https://lore.kernel.org/r/20201027073125.14229-1-keitasuzuki.park@sslab.ics.keio.ac.jp
Tested-by: Don Brace <don.brace@microchip.com>
Acked-by: Don Brace <don.brace@microchip.com>
Signed-off-by: Keita Suzuki <keitasuzuki.park@sslab.ics.keio.ac.jp>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A break is not needed if it is preceded by a return or goto.
Link: https://lore.kernel.org/r/20201019142333.16584-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pull SCSI updates from James Bottomley:
"The usual driver updates (ufs, qla2xxx, tcmu, ibmvfc, lpfc, smartpqi,
hisi_sas, qedi, qedf, mpt3sas) and minor bug fixes.
There are only three core changes: adding sense codes, cleaning up
noretry and adding an option for limitless retries"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (226 commits)
scsi: hisi_sas: Recover PHY state according to the status before reset
scsi: hisi_sas: Filter out new PHY up events during suspend
scsi: hisi_sas: Add device link between SCSI devices and hisi_hba
scsi: hisi_sas: Add check for methods _PS0 and _PR0
scsi: hisi_sas: Add controller runtime PM support for v3 hw
scsi: hisi_sas: Switch to new framework to support suspend and resume
scsi: hisi_sas: Use hisi_hba->cq_nvecs for calling calling synchronize_irq()
scsi: qedf: Remove redundant assignment to variable 'rc'
scsi: lpfc: Remove unneeded variable 'status' in lpfc_fcp_cpu_map_store()
scsi: snic: Convert to use DEFINE_SEQ_ATTRIBUTE macro
scsi: qla4xxx: Delete unneeded variable 'status' in qla4xxx_process_ddb_changed
scsi: sun_esp: Use module_platform_driver to simplify the code
scsi: sun3x_esp: Use module_platform_driver to simplify the code
scsi: sni_53c710: Use module_platform_driver to simplify the code
scsi: qlogicpti: Use module_platform_driver to simplify the code
scsi: mac_esp: Use module_platform_driver to simplify the code
scsi: jazz_esp: Use module_platform_driver to simplify the code
scsi: mvumi: Fix error return in mvumi_io_attach()
scsi: lpfc: Drop nodelist reference on error in lpfc_gen_req()
scsi: be2iscsi: Fix a theoretical leak in beiscsi_create_eqs()
...
|
|
Add entry for Microchip.
Link: https://lore.kernel.org/r/159864166227.12131.3427629298809272795.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The legacy API wrappers in include/linux/pci-dma-compat.h should go away as
they create unnecessary midlayering for include/linux/dma-mapping.h API.
Instead use dma-mapping.h API directly.
The patch has been generated with the coccinelle script below. Compile
tested.
@@@@
- PCI_DMA_BIDIRECTIONAL
+ DMA_BIDIRECTIONAL
@@@@
- PCI_DMA_TODEVICE
+ DMA_TO_DEVICE
@@@@
- PCI_DMA_FROMDEVICE
+ DMA_FROM_DEVICE
@@@@
- PCI_DMA_NONE
+ DMA_NONE
@@ expression E1, E2, E3; @@
- pci_alloc_consistent(E1, E2, E3)
+ dma_alloc_coherent(&E1->dev, E2, E3, GFP_)
@@ expression E1, E2, E3; @@
- pci_zalloc_consistent(E1, E2, E3)
+ dma_alloc_coherent(&E1->dev, E2, E3, GFP_)
@@ expression E1, E2, E3, E4; @@
- pci_free_consistent(E1, E2, E3, E4)
+ dma_free_coherent(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4; @@
- pci_map_single(E1, E2, E3, E4)
+ dma_map_single(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4; @@
- pci_unmap_single(E1, E2, E3, E4)
+ dma_unmap_single(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4, E5; @@
- pci_map_page(E1, E2, E3, E4, E5)
+ dma_map_page(&E1->dev, E2, E3, E4, E5)
@@ expression E1, E2, E3, E4; @@
- pci_unmap_page(E1, E2, E3, E4)
+ dma_unmap_page(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4; @@
- pci_map_sg(E1, E2, E3, E4)
+ dma_map_sg(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4; @@
- pci_unmap_sg(E1, E2, E3, E4)
+ dma_unmap_sg(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4; @@
- pci_dma_sync_single_for_cpu(E1, E2, E3, E4)
+ dma_sync_single_for_cpu(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4; @@
- pci_dma_sync_single_for_device(E1, E2, E3, E4)
+ dma_sync_single_for_device(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4; @@
- pci_dma_sync_sg_for_cpu(E1, E2, E3, E4)
+ dma_sync_sg_for_cpu(&E1->dev, E2, E3, E4)
@@ expression E1, E2, E3, E4; @@
- pci_dma_sync_sg_for_device(E1, E2, E3, E4)
+ dma_sync_sg_for_device(&E1->dev, E2, E3, E4)
@@ expression E1, E2; @@
- pci_dma_mapping_error(E1, E2)
+ dma_mapping_error(&E1->dev, E2)
@@ expression E1, E2; @@
- pci_set_consistent_dma_mask(E1, E2)
+ dma_set_coherent_mask(&E1->dev, E2)
@@ expression E1, E2; @@
- pci_set_dma_mask(E1, E2)
+ dma_set_mask(&E1->dev, E2)
Link: https://lore.kernel.org/r/37154a4efe82a58b9bad143608dd9fd37a2c94e5.1596045683.git.usuraj35@gmail.com
Signed-off-by: Suraj Upadhyay <usuraj35@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Need to set queue depth for controller devices.
Link: https://lore.kernel.org/r/159562590819.17915.12766718094041027754.stgit@brunhilda
Fixes: 30bda7848a23 ("scsi: hpsa: Increase controller error handling timeout")
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Link: https://lore.kernel.org/r/159528198909.24772.9189002306398058371.stgit@brunhilda
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The controller can become slow to respond to SCSI INQUIRY requests
resulting in the SCSI midlayer offlining the controller device.
Increase the timeout value for commands sent to the controller device.
Link: https://lore.kernel.org/r/159528198335.24772.7963614374905470122.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There are some rare conditions where a spare is first in the device list
causing an array out-of-bounds condition.
Link: https://lore.kernel.org/r/159528197176.24772.14659026352708896249.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Link: https://lore.kernel.org/r/20200529234028.46373-4-viro@ZenIV.linux.org.uk
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
No need for building a native struct on kernel stack, copying it to
userland one, then calling hpsa_ioctl() which copies it back into _another_
instance of the same struct.
Link: https://lore.kernel.org/r/20200529234028.46373-3-viro@ZenIV.linux.org.uk
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
"BIG" in the name refers to the amount of data being transferred, _not_ the
size of structure itself; it's 140 or 144 bytes (for 32bit and 64bit hosts
resp.). IOCTL_Command_struct is 136 or 144 bytes large...
No point whatsoever turning that into dynamic allocation, let alone vmalloc
one. Just keep it as local variable...
Link: https://lore.kernel.org/r/20200529234028.46373-2-viro@ZenIV.linux.org.uk
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Link: https://lore.kernel.org/r/20200529234028.46373-1-viro@ZenIV.linux.org.uk
Acked-by: Don Brace <don.brace@microsemi.com>
Tested-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct race condition where ioaccel is re-enabled before the raid_map is
updated. For RAID_1, RAID_1ADM, and RAID 5/6 there is a BUG_ON called which
is bad.
- Change event thread to disable ioaccel only. Send all requests down the
RAID path instead.
- Have rescan thread handle offload_enable.
- Since there is only one rescan allowed at a time, turning
offload_enabled on/off should not be racy. Each handler queues up a
rescan if one is already in progress.
- For timing diagram, offload_enabled is initially off due to a change
(transformation: splitmirror/remirror), ...
otbe = offload_to_be_enabled
oe = offload_enabled
Time Event Rescan Completion Request
Worker Worker Thread Thread
---- ------ ------ ---------- -------
T0 | | + UA |
T1 | + rescan started | 0x3f |
T2 + Event | | 0x0e |
T3 + Ack msg | | |
T4 | + if (!dev[i]->oe && | |
T5 | | dev[i]->otbe) | |
T6 | | get_raid_map | |
T7 + otbe = 1 | | |
T8 | | | |
T9 | + oe = otbe | |
T10 | | | + ioaccel request
T11 * BUG_ON
T0 - I/O completion with UA 0x3f 0x0e sets rescan flag.
T1 - rescan worker thread starts a rescan.
T2 - event comes in
T3 - event thread starts and issues "Acknowledge" message
...
T6 - rescan thread has bypassed code to reload new raid map.
...
T7 - event thread runs and sets offload_to_be_enabled
...
T9 - rescan thread turns on offload_enabled.
T10- request comes in and goes down ioaccel path.
T11- BUG_ON.
- After the patch is applied, ioaccel_enabled can only be re-enabled in
the re-scan thread.
Link: https://lore.kernel.org/r/158472877894.14200.7077843399036368335.stgit@brunhilda
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Matt Perricone <matt.perricone@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Nine changes, eight to drivers (qla2xxx, hpsa, lpfc, alua, ch,
53c710[x2], target) and one core change that tries to close a race
between sysfs delete and module removal"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: remove left-over BUILD_NVME defines
scsi: core: try to get module before removing device
scsi: hpsa: add missing hunks in reset-patch
scsi: target: core: Do not overwrite CDB byte 1
scsi: ch: Make it possible to open a ch device multiple times again
scsi: fix kconfig dependency warning related to 53C700_LE_ON_BE
scsi: sni_53c710: fix compilation error
scsi: scsi_dh_alua: handle RTPG sense code correctly during state transitions
scsi: qla2xxx: fix a potential NULL pointer dereference
|
|
Correct returning from reset before outstanding commands are completed
for the device.
Link: https://lore.kernel.org/r/157107623870.17997.11208813089704833029.stgit@brunhilda
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate _HPP/_HPX stuff in pci-acpi.c and simplify it
(Krzysztof Wilczynski)
- Fix incorrect PCIe device types and remove dev->has_secondary_link
to simplify code that deals with upstream/downstream ports (Mika
Westerberg)
- After suspend, restore Resizable BAR size bits correctly for 1MB
BARs (Sumit Saxena)
- Enable PCI_MSI_IRQ_DOMAIN support for RISC-V (Wesley Terpstra)
Virtualization:
- Add ACS quirks for iProc PAXB (Abhinav Ratna), Amazon Annapurna
Labs (Ali Saidi)
- Move sysfs SR-IOV functions to iov.c (Kelsey Skunberg)
- Remove group write permissions from sysfs sriov_numvfs,
sriov_drivers_autoprobe (Kelsey Skunberg)
Hotplug:
- Simplify pciehp indicator control (Denis Efremov)
Peer-to-peer DMA:
- Allow P2P DMA between root ports for whitelisted bridges (Logan
Gunthorpe)
- Whitelist some Intel host bridges for P2P DMA (Logan Gunthorpe)
- DMA map P2P DMA requests that traverse host bridge (Logan
Gunthorpe)
Amazon Annapurna Labs host bridge driver:
- Add DT binding and controller driver (Jonathan Chocron)
Hyper-V host bridge driver:
- Fix hv_pci_dev->pci_slot use-after-free (Dexuan Cui)
- Fix PCI domain number collisions (Haiyang Zhang)
- Use instance ID bytes 4 & 5 as PCI domain numbers (Haiyang Zhang)
- Fix build errors on non-SYSFS config (Randy Dunlap)
i.MX6 host bridge driver:
- Limit DBI register length (Stefan Agner)
Intel VMD host bridge driver:
- Fix config addressing issues (Jon Derrick)
Layerscape host bridge driver:
- Add bar_fixed_64bit property to endpoint driver (Xiaowei Bao)
- Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC drivers separately
(Xiaowei Bao)
Mediatek host bridge driver:
- Add MT7629 controller support (Jianjun Wang)
Mobiveil host bridge driver:
- Fix CPU base address setup (Hou Zhiqiang)
- Make "num-lanes" property optional (Hou Zhiqiang)
Tegra host bridge driver:
- Fix OF node reference leak (Nishka Dasgupta)
- Disable MSI for root ports to work around design problem (Vidya
Sagar)
- Add Tegra194 DT binding and controller support (Vidya Sagar)
- Add support for sideband pins and slot regulators (Vidya Sagar)
- Add PIPE2UPHY support (Vidya Sagar)
Misc:
- Remove unused pci_block_cfg_access() et al (Kelsey Skunberg)
- Unexport pci_bus_get(), etc (Kelsey Skunberg)
- Hide PM, VC, link speed, ATS, ECRC, PTM constants and interfaces in
the PCI core (Kelsey Skunberg)
- Clean up sysfs DEVICE_ATTR() usage (Kelsey Skunberg)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Propagate errors for optional regulators and PHYs (Thierry Reding)
- Fix kernel command line resource_alignment parameter issues (Logan
Gunthorpe)"
* tag 'pci-v5.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (112 commits)
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
PCI: vmd: Fix shadow offsets to reflect spec changes
PCI: vmd: Fix config addressing when using bus offsets
PCI: dwc: Add validation that PCIe core is set to correct mode
PCI: dwc: al: Add Amazon Annapurna Labs PCIe controller driver
dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding
PCI: Add quirk to disable MSI-X support for Amazon's Annapurna Labs Root Port
PCI/VPD: Prevent VPD access for Amazon's Annapurna Labs Root Port
PCI: Add ACS quirk for Amazon Annapurna Labs root ports
PCI: Add Amazon's Annapurna Labs vendor ID
MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer
PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
PCI: Get rid of dev->has_secondary_link flag
...
|
|
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Seven fixes to four drivers with no core changes.
The mpt3sas one is theoretical until we get a CPU that goes up to 64
bits physical, the qla2xxx one fixes an oops in a driver
initialization error leg and the others are mostly cosmetic"
[ The fcoe patches may be worth highlighting - they may be "just"
cleanups, but they simplify and fix the odd fc_rport_priv structure
handling rules so that the new gcc-9 warnings about memset crossing
structure boundaries are gone.
The old code was hard for humans to understand too, and really
confused the compiler sanity checks - Linus ]
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla2xxx: Fix possible fcport null-pointer dereferences
scsi: mpt3sas: Use 63-bit DMA addressing on SAS35 HBA
scsi: hpsa: remove printing internal cdb on tag collision
scsi: hpsa: correct scsi command status issue after reset
scsi: fcoe: pass in fcoe_rport structure instead of fc_rport_priv
scsi: fcoe: Embed fc_rport_priv in fcoe_rport structure
scsi: libfc: Whitespace cleanup in libfc.h
|
|
Remove racy printing of internal commands. Completion thread can be
cleaning up the command in parallel.
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Some files got renamed but probably due to some merge conflicts,
a few references still point to the old locations.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, hpsa, lpfc, ufs,
mpt3sas, ibmvscsi, megaraid_sas, bnx2fc and hisi_sas as well as the
removal of the osst driver (I heard from Willem privately that he
would like the driver removed because all his test hardware has
failed). Plus number of minor changes, spelling fixes and other
trivia.
The big merge conflict this time around is the SPDX licence tags.
Following discussion on linux-next, we believe our version to be more
accurate than the one in the tree, so the resolution is to take our
version for all the SPDX conflicts"
Note on the SPDX license tag conversion conflicts: the SCSI tree had
done its own SPDX conversion, which in some cases conflicted with the
treewide ones done by Thomas & co.
In almost all cases, the conflicts were purely syntactic: the SCSI tree
used the old-style SPDX tags ("GPL-2.0" and "GPL-2.0+") while the
treewide conversion had used the new-style ones ("GPL-2.0-only" and
"GPL-2.0-or-later").
In these cases I picked the new-style one.
In a few cases, the SPDX conversion was actually different, though. As
explained by James above, and in more detail in a pre-pull-request
thread:
"The other problem is actually substantive: In the libsas code Luben
Tuikov originally specified gpl 2.0 only by dint of stating:
* This file is licensed under GPLv2.
In all the libsas files, but then muddied the water by quoting GPLv2
verbatim (which includes the or later than language). So for these
files Christoph did the conversion to v2 only SPDX tags and Thomas
converted to v2 or later tags"
So in those cases, where the spdx tag substantially mattered, I took the
SCSI tree conversion of it, but then also took the opportunity to turn
the old-style "GPL-2.0" into a new-style "GPL-2.0-only" tag.
Similarly, when there were whitespace differences or other differences
to the comments around the copyright notices, I took the version from
the SCSI tree as being the more specific conversion.
Finally, in the spdx conversions that had no conflicts (because the
treewide ones hadn't been done for those files), I just took the SCSI
tree version as-is, even if it was old-style. The old-style conversions
are perfectly valid, even if the "-only" and "-or-later" versions are
perhaps more descriptive.
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (185 commits)
scsi: qla2xxx: move IO flush to the front of NVME rport unregistration
scsi: qla2xxx: Fix NVME cmd and LS cmd timeout race condition
scsi: qla2xxx: on session delete, return nvme cmd
scsi: qla2xxx: Fix kernel crash after disconnecting NVMe devices
scsi: megaraid_sas: Update driver version to 07.710.06.00-rc1
scsi: megaraid_sas: Introduce various Aero performance modes
scsi: megaraid_sas: Use high IOPS queues based on IO workload
scsi: megaraid_sas: Set affinity for high IOPS reply queues
scsi: megaraid_sas: Enable coalescing for high IOPS queues
scsi: megaraid_sas: Add support for High IOPS queues
scsi: megaraid_sas: Add support for MPI toolbox commands
scsi: megaraid_sas: Offload Aero RAID5/6 division calculations to driver
scsi: megaraid_sas: RAID1 PCI bandwidth limit algorithm is applicable for only Ventura
scsi: megaraid_sas: megaraid_sas: Add check for count returned by HOST_DEVICE_LIST DCMD
scsi: megaraid_sas: Handle sequence JBOD map failure at driver level
scsi: megaraid_sas: Don't send FPIO to RL Bypass queue
scsi: megaraid_sas: In probe context, retry IOC INIT once if firmware is in fault
scsi: megaraid_sas: Release Mutex lock before OCR in case of DCMD timeout
scsi: megaraid_sas: Call disable_irq from process IRQ poll
scsi: megaraid_sas: Remove few debug counters from IO path
...
|
|
Pull Documentation updates from Jonathan Corbet:
"It's been a relatively busy cycle for docs:
- A fair pile of RST conversions, many from Mauro. These create more
than the usual number of simple but annoying merge conflicts with
other trees, unfortunately. He has a lot more of these waiting on
the wings that, I think, will go to you directly later on.
- A new document on how to use merges and rebases in kernel repos,
and one on Spectre vulnerabilities.
- Various improvements to the build system, including automatic
markup of function() references because some people, for reasons I
will never understand, were of the opinion that
:c:func:``function()`` is unattractive and not fun to type.
- We now recommend using sphinx 1.7, but still support back to 1.4.
- Lots of smaller improvements, warning fixes, typo fixes, etc"
* tag 'docs-5.3' of git://git.lwn.net/linux: (129 commits)
docs: automarkup.py: ignore exceptions when seeking for xrefs
docs: Move binderfs to admin-guide
Disable Sphinx SmartyPants in HTML output
doc: RCU callback locks need only _bh, not necessarily _irq
docs: format kernel-parameters -- as code
Doc : doc-guide : Fix a typo
platform: x86: get rid of a non-existent document
Add the RCU docs to the core-api manual
Documentation: RCU: Add TOC tree hooks
Documentation: RCU: Rename txt files to rst
Documentation: RCU: Convert RCU UP systems to reST
Documentation: RCU: Convert RCU linked list to reST
Documentation: RCU: Convert RCU basic concepts to reST
docs: filesystems: Remove uneeded .rst extension on toctables
scripts/sphinx-pre-install: fix out-of-tree build
docs: zh_CN: submitting-drivers.rst: Remove a duplicated Documentation/
Documentation: PGP: update for newer HW devices
Documentation: Add section about CPU vulnerabilities for Spectre
Documentation: platform: Delete x86-laptop-drivers.txt
docs: Note that :c:func: should no longer be used
...
|
|
Currently the check for a lockup_detected failure exits via the label
return_reset_status that reads and dereferences an uninitialized pointer
dev. Fix this by ensuring dev is inintialized to null.
Addresses-Coverity: ("Uninitialized pointer read")
Fixes: 14991a5bade5 ("scsi: hpsa: correct device resets")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
[mkp: wrong baseline, applied by hand]
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct a race condition that occurs between the reset handler and the
completion handler. There are times when the wait_event condition is
never met due to this race condition and the reset never completes.
The reset_pending field is NULL initially.
t Reset Handler Thread Completion Thread
-- -------------------- -----------------
t1 if (c->reset_pending)
t2 c->reset_pending = dev; if (atomic_dev_and_test(counter))
t3 atomic_inc(counter) wait_up_all(event_sync_wait_queue)
t4
t5 wait_event(...counter == 0)
Kernel.org Bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=1994350
Bug 199435 - HPSA + P420i resetting logical Direct-Access
never complete
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Close up a rare multipath issue.
Close up small hole where a command completes after a device has been
removed from SML and before the device is re-added.
- Mark device as removed in slave_destroy
- Do not complete commands for deleted devices
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Wait longer for outstanding commands before removing a multipath
device. Increase the timeout value for ptraid commands.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct rare multipath issue where a device is deleted with an
outstanding cmd which results in a tag collision.
The cmd eventually completes. If a collision is detected wait until
the command slot is cleared.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Avoid system stalls by switching to local workqueue.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: David Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct issue with hpsa_simple_mode module parameter. Driver was
hanging due to incorrect interrupt setup.
Reviewed-by: Justin Lindley <justin.lindley@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Some documentation files were still pointing to the old place.
Fixes: 229b4e0728e0 ("Documentation: PCI: convert pci.txt to reST")
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Paul E. McKenney <paulmck@linux.ibm.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
- set ioaccel2_sg_element member 'chain_indicator' to IOACCEL2_LAST_SG for
the last s/g element.
- set ioaccel2_sg_element member 'chain_indicator' to IOACCEL2_CHAIN when
chaining.
Reviewed-by: Bader Ali - Saleh <bader.alisaleh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Matt Perricone <matt.perricone@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Reviewed-by: Gerry Morong <gerry.morong@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There are times when a TUR can take longer than the DEFAULT_TIMEOUT
value. The timeout code is not correct as the function exits with an
automatic as the completion variable...To be fixed later.
Remove the TUR timeout.
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Correct a 'rare' race condition where a disk is failed after a device list
has been obtained from the controller and before attempting to get the
device id.
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Multipath failures are normally detected at the frequency of the event
thread. Detect LUN failures earlier by checking request completion status.
Reviewed-by: Bader Ali-saleh <bader.ali-saleh@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Reviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Prasad Munirathnam <Prasad.Munirathnam@microsemi.com>
Reviewed-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Clang warns several times in the scsi subsystem (trimmed for brevity):
drivers/scsi/hpsa.c:6209:7: warning: overflow converting case value to
switch condition type (2147762695 to 18446744071562347015) [-Wswitch]
case CCISS_GETBUSTYPES:
^
drivers/scsi/hpsa.c:6208:7: warning: overflow converting case value to
switch condition type (2147762694 to 18446744071562347014) [-Wswitch]
case CCISS_GETHEARTBEAT:
^
The root cause is that the _IOC macro can generate really large numbers,
which don't fit into type 'int', which is used for the cmd parameter in
the ioctls in scsi_host_template. My research into how GCC and Clang are
handling this at a low level didn't prove fruitful. However, looking at
the rest of the kernel tree, all ioctls use an 'unsigned int' for the
cmd parameter, which will fit all of the _IOC values in the scsi/ata
subsystems.
Make that change because none of the ioctls expect a negative value for
any command, it brings the ioctls inline with the reset of the kernel,
and it removes ambiguity, which is never good when dealing with compilers.
Link: https://github.com/ClangBuiltLinux/linux/issues/85
Link: https://github.com/ClangBuiltLinux/linux/issues/154
Link: https://github.com/ClangBuiltLinux/linux/issues/157
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Bradley Grove <bgrove@attotech.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There are two statements that are indented incorrectly. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Addresses-Coverity-ID: 1195463 ("Missing break in switch")
Addresses-Coverity-ID: 1195464 ("Missing break in switch")
Addresses-Coverity-ID: 1195465 ("Missing break in switch")
Addresses-Coverity-ID: 1195466 ("Missing break in switch")
Addresses-Coverity-ID: 1357338 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
