| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"There's a little bit of everything in here: we've got various
improvements and cleanups to drivers, some fixes across the board and
a bit of new hardware support"
* tag 'pwm/for-6.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (22 commits)
dt-bindings: pwm: convert pwm-bcm2835 bindings to YAML
pwm: Add Renesas RZ/G2L MTU3a PWM driver
pwm: mtk_disp: Fix the disable flow of disp_pwm
dt-bindings: pwm: restrict node name suffixes
pwm: pca9685: Switch i2c driver back to use .probe()
pwm: ab8500: Fix error code in probe()
MAINTAINERS: add pwm to PolarFire SoC entry
pwm: add microchip soft ip corePWM driver
pwm: sysfs: Do not apply state to already disabled PWMs
pwm: imx-tpm: force 'real_period' to be zero in suspend
pwm: meson: make full use of common clock framework
pwm: meson: don't use hdmi/video clock as mux parent
pwm: meson: switch to using struct clk_parent_data for mux parents
pwm: meson: remove not needed check in meson_pwm_calc
pwm: meson: fix handling of period/duty if greater than UINT_MAX
pwm: meson: modify and simplify calculation in meson_pwm_get_state
dt-bindings: pwm: Add R-Car V3U device tree bindings
dt-bindings: pwm: imx: add i.MX8QXP compatible
pwm: mediatek: Add support for MT7981
dt-bindings: pwm: mediatek: Add mediatek,mt7981 compatible
...
|
|
The RZ/G2L Multi-Function Timer Pulse Unit 3 (a.k.a MTU3a) uses
one counter and two match components to configure duty_cycle
and period to generate PWM output waveform.
Add basic support for RZ/G2L MTU3a PWM driver by creating separate
PWM channels for each IOs.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
There is a flow error in the original mtk_disp_pwm_apply() function.
If this function is called when the clock is disabled, there will be a
chance to operate the disp_pwm register, resulting in disp_pwm exception.
Fix this accordingly.
Fixes: 888a623db5d0 ("pwm: mtk-disp: Implement atomic API .apply()")
Signed-off-by: Shuijing Li <shuijing.li@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-by: Fei Shao <fshao@chromium.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This code accidentally return positive EINVAL instead of negative
-EINVAL.
Fixes: eb41f334589d ("pwm: ab8500: Fix register offset calculation to not depend on probe order")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Add a driver that supports the Microchip FPGA "soft" PWM IP core.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
If the PWM is exported but not enabled, do not call pwm_class_apply_state().
First of all, in this case, period may still be unconfigured and this would
make pwm_class_apply_state() return -EINVAL, and then suspend would fail.
Second, it makes little sense to apply state onto PWM that is not enabled
before suspend.
Failing case:
"
$ echo 1 > /sys/class/pwm/pwmchip4/export
$ echo mem > /sys/power/state
...
pwm pwmchip4: PM: dpm_run_callback(): pwm_class_suspend+0x1/0xa8 returns -22
pwm pwmchip4: PM: failed to suspend: error -22
PM: Some devices failed to suspend, or early wake event detected
"
Working case:
"
$ echo 1 > /sys/class/pwm/pwmchip4/export
$ echo 100 > /sys/class/pwm/pwmchip4/pwm1/period
$ echo 10 > /sys/class/pwm/pwmchip4/pwm1/duty_cycle
$ echo mem > /sys/power/state
...
"
Do not call pwm_class_apply_state() in case the PWM is disabled
to fix this issue.
Fixes: 7fd4edc57bbae ("pwm: sysfs: Add suspend/resume support")
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: ef2bf4997f7d ("pwm: Improve args checking in pwm_apply_state()")
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
During suspend, all the tpm registers will lose values.
So the 'real_period' value of struct 'imx_tpm_pwm_chip'
should be forced to be zero to force the period update
code can be executed after system resume back.
Signed-off-by: Fancy Fang <chen.fang@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 738a1cfec2ed ("pwm: Add i.MX TPM PWM driver support")
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Newer versions of the PWM block use a core clock with external mux,
divider, and gate. These components either don't exist any longer in
the PWM block, or they are bypassed.
To minimize needed changes for supporting the new version, the internal
divider and gate should be handled by CCF too.
I didn't see a good way to split the patch, therefore it's somewhat
bigger. What it does:
- The internal mux is handled by CCF already. Register also internal
divider and gate with CCF, so that we have one representation of the
input clock: [mux] parent of [divider] parent of [gate]
- Now that CCF selects an appropriate mux parent, we don't need the
DT-provided default parent any longer. Accordingly we can also omit
setting the mux parent directly in the driver.
- Instead of manually handling the pre-div divider value, let CCF
set the input clock. Targeted input clock frequency is
0xffff * 1/period for best precision.
- For the "inverted pwm disabled" scenario target an input clock
frequency of ULONG_MAX. This ensures that the remaining low pulses
have minimum length.
I don't have hw with the old PWM block, therefore I couldn't test this
patch. With the not yet included extension for the new PWM block
(channel->clk coming directly from get_clk(external_clk)) I didn't
notice any problem. My system uses PWM for the CPU voltage regulator
and for the SDIO 32kHz clock.
Note: The clock gate in the old PWM block is permanently disabled.
This seems to indicate that it's not used by the new PWM block.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The meson_vclk code from the display driver may change the rate of the
video clock. Therefore better don't use it as pwm mux parent.
After removing this clock from the parent list pwm_gxbb_data and
pwm_g12a_ee_data are the same as pwm_meson8b_data. So we can remove
them.
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
We'll use struct clk_parent_data for mux/div/gate initialization in the
follow-up patches. As a first step switch the mux from using
parent_names to clk_parent_data.
Suggested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
period >= duty implies that cnt >= duty_cnt. We verified before
that cnt <= 0xffff, therefore we can omit the check here.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
state->period/duty are of type u64, and if their value is greater than
UINT_MAX, then the cast to uint will cause problems. Fix this by
changing the type of the respective local variables to u64.
Fixes: b79c3670e120 ("pwm: meson: Don't duplicate the polarity internally")
Cc: stable@vger.kernel.org
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
I don't see a reason why we should treat the case lo < hi differently
and return 0 as period and duty_cycle. The current logic was added with
c375bcbaabdb ("pwm: meson: Read the full hardware state in
meson_pwm_get_state()"), Martin as original author doesn't remember why
it was implemented this way back then.
So let's handle it as normal use case and also remove the optimization
for lo == 0. I think the improved readability is worth it.
Fixes: c375bcbaabdb ("pwm: meson: Read the full hardware state in meson_pwm_get_state()")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Dmitry Rokosov <ddrokosov@sberdevices.ru>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM unit on MT7981 uses different register offsets than previous
MediaTek PWM units. Add support for these new offsets and add support
for PWM on MT7981 which has 3 PWM channels, one of them is typically
used for a temperature controlled fan.
While at it, also reorder pwm_mediatek_of_data entries to restore
alphabetic order.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Instead of preparing the clk after it was requested and unpreparing in
.probe()'s error path and .remove(), use devm_clk_get_prepared() which
copes for unpreparing automatically.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Emil Renner Berthing <emil.renner.berthing@canonical.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Use the devm_clk_get_prepared() helper function instead of hand-writing it.
It saves some line of codes.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The Arm documentation has moved to Documentation/arch/arm; update the
last remaining references to match.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for pwm
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The bulk of this is trivial conversions to the new .remove_new()
callback for drivers as part of Uwe's effort to clean that up.
Other than that a driver is added for Apple devices and various small
fixes are included for existing drivers.
Last but not least, this finally gets rid of the old pwm_request() and
pwm_free() APIs are removed since the last user was dropped in v6.3"
* tag 'pwm/for-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (44 commits)
pwm: Remove unused radix tree
pwm: Delete deprecated functions pwm_request() and pwm_free()
pwm: meson: Fix g12a ao clk81 name
pwm: meson: Fix axg ao mux parents
pwm: stm32: Enforce settings for PWM capture
MAINTAINERS: Add entries for Apple PWM driver
pwm: Add Apple PWM controller
dt-bindings: pwm: Add Apple PWM controller
pwm: mtk-disp: Configure double buffering before reading in .get_state()
pwm: mtk-disp: Disable shadow registers before setting backlight values
pwm: stm32-lp: Drop of_match_ptr for ID table
pwm: rcar: Drop of_match_ptr for ID table
dt-bindings: pwm: Convert Amlogic Meson PWM binding
dt-bindings: pwm: mediatek: Add mediatek,mt7986 compatible
pwm: xilinx: Convert to platform remove callback returning void
pwm: vt8500: Convert to platform remove callback returning void
pwm: tiehrpwm: Convert to platform remove callback returning void
pwm: tiecap: Convert to platform remove callback returning void
pwm: tegra: Convert to platform remove callback returning void
pwm: sun4i: Convert to platform remove callback returning void
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the large set of driver core changes for 6.4-rc1.
Once again, a busy development cycle, with lots of changes happening
in the driver core in the quest to be able to move "struct bus" and
"struct class" into read-only memory, a task now complete with these
changes.
This will make the future rust interactions with the driver core more
"provably correct" as well as providing more obvious lifetime rules
for all busses and classes in the kernel.
The changes required for this did touch many individual classes and
busses as many callbacks were changed to take const * parameters
instead. All of these changes have been submitted to the various
subsystem maintainers, giving them plenty of time to review, and most
of them actually did so.
Other than those changes, included in here are a small set of other
things:
- kobject logging improvements
- cacheinfo improvements and updates
- obligatory fw_devlink updates and fixes
- documentation updates
- device property cleanups and const * changes
- firwmare loader dependency fixes.
All of these have been in linux-next for a while with no reported
problems"
* tag 'driver-core-6.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (120 commits)
device property: make device_property functions take const device *
driver core: update comments in device_rename()
driver core: Don't require dynamic_debug for initcall_debug probe timing
firmware_loader: rework crypto dependencies
firmware_loader: Strip off \n from customized path
zram: fix up permission for the hot_add sysfs file
cacheinfo: Add use_arch[|_cache]_info field/function
arch_topology: Remove early cacheinfo error message if -ENOENT
cacheinfo: Check cache properties are present in DT
cacheinfo: Check sib_leaf in cache_leaves_are_shared()
cacheinfo: Allow early level detection when DT/ACPI info is missing/broken
cacheinfo: Add arm64 early level initializer implementation
cacheinfo: Add arch specific early level initializer
tty: make tty_class a static const structure
driver core: class: remove struct class_interface * from callbacks
driver core: class: mark the struct class in struct class_interface constant
driver core: class: make class_register() take a const *
driver core: class: mark class_release() as taking a const *
driver core: remove incorrect comment for device_create*
MIPS: vpe-cmp: remove module owner pointer from struct class usage.
...
|
|
The radix tree's only use was to map PWM channels to the global number
space. With that number space gone, the radix tree is now unused, so it
can simply be removed.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Since commit 5a7fbe452ad9 ("backlight: pwm_bl: Drop support for legacy PWM
probing") the last user of pwm_request() and pwm_free() is gone. So remove
these functions that were deprecated over 10 years ago in commit
8138d2ddbcca ("pwm: Add table-based lookup for static mappings").
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[thierry.reding@gmail.com: clean up a bit after removal]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Fix the name of the aoclk81 clock. Apparently name aoclk81 as used by
the vendor driver was changed when mainlining the g12a clock driver.
Fixes: f41efceb46e6 ("pwm: meson: Add clock source configuration for Meson G12A")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
This fix is basically the same as 9bce02ef0dfa ("pwm: meson: Fix the
G12A AO clock parents order"). Vendor driver referenced there has
xtal as first parent also for axg ao. In addition fix the name
of the aoclk81 clock. Apparently name aoclk81 as used by the vendor
driver was changed when mainlining the axg clock driver.
Fixes: bccaa3f917c9 ("pwm: meson: Add clock source configuration for Meson-AXG")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The PWM capture assumes that the input selector is set to default
input and that the slave mode is disabled. Force reset state for
TISEL and SMCR registers to match this requirement.
Note that slave mode disabling is not a pre-requisite by itself
for capture mode, as hardware supports it for PWM capture.
However, the current implementation of the driver does not
allow slave mode for PWM capture. Setting slave mode for PWM
capture results in wrong capture values.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
Adds the Apple PWM controller driver.
Signed-off-by: Sasha Finkelstein <fnkl.kernel@gmail.com>
Acked-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The DISP_PWM controller's default behavior is to always use register
double buffering: all reads/writes are then performed on shadow
registers instead of working registers and this becomes an issue
in case our chosen configuration in Linux is different from the
default (or from the one that was pre-applied by the bootloader).
An example of broken behavior is when the controller is configured
to use shadow registers, but this driver wants to configure it
otherwise: what happens is that the .get_state() callback is called
right after registering the pwmchip and checks whether the PWM is
enabled by reading the DISP_PWM_EN register;
At this point, if shadow registers are enabled but their content
was not committed before booting Linux, we are *not* reading the
current PWM enablement status, leading to the kernel knowing that
the hardware is actually enabled when, in reality, it's not.
The aforementioned issue emerged since this driver was fixed with
commit 0b5ef3429d8f ("pwm: mtk-disp: Fix the parameters calculated
by the enabled flag of disp_pwm") making it to read the enablement
status from the right register.
Configure the controller in the .get_state() callback to avoid
this desync issue and get the backlight properly working again.
Fixes: 3f2b16734914 ("pwm: mtk-disp: Implement atomic API .get_state()")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
If shadow registers usage is not desired, disable that before performing
any write to CON0/1 registers in the .apply() callback, otherwise we may
lose clkdiv or period/width updates.
Fixes: cd4b45ac449a ("pwm: Add MediaTek MT2701 display PWM driver support")
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: Alexandre Mergnat <amergnat@baylibre.com>
Tested-by: Alexandre Mergnat <amergnat@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes the following compile error:
drivers/pwm/pwm-stm32-lp.c:245:34: error: ‘stm32_pwm_lp_of_match’ defined but not used [-Werror=unused-const-variable=]
for builds with CONFIG_OF=n, CONFIG_PWM_STM32_LP=y and W=1.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes the following compiler warning:
drivers/pwm/pwm-rcar.c:252:34: error: ‘rcar_pwm_of_table’ defined but not used [-Werror=unused-const-variable=]
for builds with CONFIG_OF=n, CONFIG_PWM_RCAR=y and W=1.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is (mostly) ignored
and this typically results in resource leaks. To improve here there is a
quest to make the remove callback return void. In the first step of this
quest all drivers are converted to .remove_new() which already returns
void.
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
|
