summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/bcm
AgeCommit message (Collapse)Author
2018-12-21pinctrl: bcm: ns: support updated DT binding as syscon subnodeRafał Miłecki
Documentation has been recently updated specifying that pinctrl should be subnode of the CRU "syscon". Support that by using parent node for regmap and reading "offset" property from the DT. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-16pinctrl: bcm2835: Switch to SPDX identifierStefan Wahren
Adopt the SPDX license identifier headers to ease license compliance management. Cc: Simon Arlott <simon@arlott.org> Cc: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-09pinctrl: bcm2835: Use define directive for BCM2835_PINCONF_PARAM_PULLNathan Chancellor
Clang warns when one enumerated type is implicitly converted to another: drivers/pinctrl/bcm/pinctrl-bcm2835.c:707:40: warning: implicit conversion from enumeration type 'enum bcm2835_pinconf_param' to different enumeration type 'enum pin_config_param' [-Wenum-conversion] configs[0] = pinconf_to_config_packed(BCM2835_PINCONF_PARAM_PULL, pull); ~~~~~~~~~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~~~~~~ 1 warning generated. It is expected that pinctrl drivers can extend pin_config_param because of the gap between PIN_CONFIG_END and PIN_CONFIG_MAX so this conversion isn't an issue. Most drivers that take advantage of this define the PIN_CONFIG variables as constants, rather than enumerated values. Do the same thing here so that Clang no longer warns. Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-11-05pinctrl: bcm2835: Use raw spinlock for RT compatibilityLukas Wunner
The BCM2835 pinctrl driver acquires a spinlock in its ->irq_enable, ->irq_disable and ->irq_set_type callbacks. Spinlocks become sleeping locks with CONFIG_PREEMPT_RT_FULL=y, therefore invocation of one of the callbacks in atomic context may cause a hard lockup if at least two GPIO pins in the same bank are used as interrupts. The issue doesn't occur with just a single interrupt pin per bank because the lock is never contended. I'm experiencing such lockups with GPIO 8 and 28 used as level-triggered interrupts, i.e. with ->irq_disable being invoked on reception of every IRQ. The critical section protected by the spinlock is very small (one bitop and one RMW of an MMIO register), hence converting to a raw spinlock seems a better trade-off than converting the driver to threaded IRQ handling (which would increase latency to handle an interrupt). Cc: Mathias Duckeck <m.duckeck@kunbus.de> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Julia Cartwright <julia@ni.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-12pinctrl: bcm: ns: Use uintptr_t for casting dataRafał Miłecki
Fix up a compiler error on 64bit architectures where pointers and integers differ in size. Suggested-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-10-10pinctrl: bcm: add Northstar driverRafał Miłecki
This driver provides support for Northstar mux controller. It differs from Northstar Plus one so a new binding and driver were needed. Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-14pinctrl: nsp: Fix potential NULL dereferenceWei Yongjun
platform_get_resource() may fail and return NULL, so we should better check it's return value to avoid a NULL pointer dereference a bit later in the code. This is detected by Coccinelle semantic patch. @@ expression pdev, res, n, t, e, e1, e2; @@ res = platform_get_resource(pdev, t, n); + if (!res) + return -EINVAL; ... when != res == NULL e = devm_ioremap_nocache(e1, res->start, e2); Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-07-14pinctrl: nsp: off by ones in nsp_pinmux_enable()Dan Carpenter
The > comparisons should be >= or else we read beyond the end of the pinctrl->functions[] array. Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-06-12treewide: kzalloc() -> kcalloc()Kees Cook
The kzalloc() function has a 2-factor argument form, kcalloc(). This patch replaces cases of: kzalloc(a * b, gfp) with: kcalloc(a * b, gfp) as well as handling cases of: kzalloc(a * b * c, gfp) with: kzalloc(array3_size(a, b, c), gfp) as it's slightly less ugly than: kzalloc_array(array_size(a, b), c, gfp) This does, however, attempt to ignore constant size factors like: kzalloc(4 * 1024, gfp) though any constants defined via macros get caught up in the conversion. Any factors with a sizeof() of "unsigned char", "char", and "u8" were dropped, since they're redundant. The Coccinelle script used for this was: // Fix redundant parens around sizeof(). @@ type TYPE; expression THING, E; @@ ( kzalloc( - (sizeof(TYPE)) * E + sizeof(TYPE) * E , ...) | kzalloc( - (sizeof(THING)) * E + sizeof(THING) * E , ...) ) // Drop single-byte sizes and redundant parens. @@ expression COUNT; typedef u8; typedef __u8; @@ ( kzalloc( - sizeof(u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(__u8) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(unsigned char) * (COUNT) + COUNT , ...) | kzalloc( - sizeof(u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(__u8) * COUNT + COUNT , ...) | kzalloc( - sizeof(char) * COUNT + COUNT , ...) | kzalloc( - sizeof(unsigned char) * COUNT + COUNT , ...) ) // 2-factor product with sizeof(type/expression) and identifier or constant. @@ type TYPE; expression THING; identifier COUNT_ID; constant COUNT_CONST; @@ ( - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_ID) + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_ID + COUNT_ID, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (COUNT_CONST) + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * COUNT_CONST + COUNT_CONST, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_ID) + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_ID + COUNT_ID, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (COUNT_CONST) + COUNT_CONST, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * COUNT_CONST + COUNT_CONST, sizeof(THING) , ...) ) // 2-factor product, only identifiers. @@ identifier SIZE, COUNT; @@ - kzalloc + kcalloc ( - SIZE * COUNT + COUNT, SIZE , ...) // 3-factor product with 1 sizeof(type) or sizeof(expression), with // redundant parens removed. @@ expression THING; identifier STRIDE, COUNT; type TYPE; @@ ( kzalloc( - sizeof(TYPE) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(TYPE) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(TYPE)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * (COUNT) * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * (STRIDE) + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) | kzalloc( - sizeof(THING) * COUNT * STRIDE + array3_size(COUNT, STRIDE, sizeof(THING)) , ...) ) // 3-factor product with 2 sizeof(variable), with redundant parens removed. @@ expression THING1, THING2; identifier COUNT; type TYPE1, TYPE2; @@ ( kzalloc( - sizeof(TYPE1) * sizeof(TYPE2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(THING1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(THING1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * COUNT + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) | kzalloc( - sizeof(TYPE1) * sizeof(THING2) * (COUNT) + array3_size(COUNT, sizeof(TYPE1), sizeof(THING2)) , ...) ) // 3-factor product, only identifiers, with redundant parens removed. @@ identifier STRIDE, SIZE, COUNT; @@ ( kzalloc( - (COUNT) * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * STRIDE * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - (COUNT) * (STRIDE) * (SIZE) + array3_size(COUNT, STRIDE, SIZE) , ...) | kzalloc( - COUNT * STRIDE * SIZE + array3_size(COUNT, STRIDE, SIZE) , ...) ) // Any remaining multi-factor products, first at least 3-factor products, // when they're not all constants... @@ expression E1, E2, E3; constant C1, C2, C3; @@ ( kzalloc(C1 * C2 * C3, ...) | kzalloc( - (E1) * E2 * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * E3 + array3_size(E1, E2, E3) , ...) | kzalloc( - (E1) * (E2) * (E3) + array3_size(E1, E2, E3) , ...) | kzalloc( - E1 * E2 * E3 + array3_size(E1, E2, E3) , ...) ) // And then all remaining 2 factors products when they're not all constants, // keeping sizeof() as the second factor argument. @@ expression THING, E1, E2; type TYPE; constant C1, C2, C3; @@ ( kzalloc(sizeof(THING) * C2, ...) | kzalloc(sizeof(TYPE) * C2, ...) | kzalloc(C1 * C2 * C3, ...) | kzalloc(C1 * C2, ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * (E2) + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(TYPE) * E2 + E2, sizeof(TYPE) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * (E2) + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - sizeof(THING) * E2 + E2, sizeof(THING) , ...) | - kzalloc + kcalloc ( - (E1) * E2 + E1, E2 , ...) | - kzalloc + kcalloc ( - (E1) * (E2) + E1, E2 , ...) | - kzalloc + kcalloc ( - E1 * E2 + E1, E2 , ...) ) Signed-off-by: Kees Cook <keescook@chromium.org>
2018-05-16pinctrl: bcm2835: Add support for output-low output-high propertiesMatheus Castello
Properties to set initial value of pin output buffer. This can be useful for configure hardware in overlay files, and in early boot for checking it states in QA sanity tests. Signed-off-by: Matheus Castello <matheus@castello.eng.br> Reviewed-by: Eric Anholt <eric@anholt.net> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2018-05-16pinctrl: bcm2835: Add support for generic pinctrl bindingMatheus Castello
To keep driver up to date we add generic pinctrl binding support, which covers the features used in this driver and has additional node properties that this SoC has compatibility, so enabling future implementations of these properties without the need to create new node properties in the device trees. The logic of this change maintain the old brcm legacy binding support in order to keep the ABI stable. Signed-off-by: Matheus Castello <matheus@castello.eng.br> Reviewed-by: Eric Anholt <eric@anholt.net> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-16Merge tag 'pinctrl-v4.15-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pin control updates from Linus Walleij: "This is the bulk of pin control changes for the v4.15 kernel cycle: Core: - The pin control Kconfig entry PINCTRL is now turned into a menuconfig option. This obviously has the implication of making the subsystem menu visible in menuconfig. This is happening because of two things: (a) Intel have started to deploy and depend on pin controllers in a way that is affecting users directly. This happens on the highly integrated laptop chipsets named after geographical places: baytrail, broxton, cannonlake, cedarfork, cherryview, denverton, geminilake, lewisburg, merrifield, sunrisepoint... It started a while back and now it is ever more evident that this is crucial infrastructure for x86 laptops and not an embedded obscurity anymore. Users need to be aware. (b) Pin control expanders on I2C and SPI that are arch-agnostic. Currently Semtech SX150X and Microchip MCP28x08 but more are expected. Users will have to be able to configure these in directly for their set-up. - Just go and select GPIOLIB now that we made sure that GPIOLIB is a very vanilla subsystem. Do not depend on it, if we need it, select it. - Exposing the pin control subsystem in menuconfig uncovered a bunch of obscure bugs that are now hopefully fixed, all more or less pertaining to Blackfin. - Unified namespace for cross-calls between pin control and GPIO. - New support for clock skew/delay generic DT bindings and generic pin config options for this. - Minor documentation improvements. Various: - The Renesas SH-PFC pin controller has evolved a lot. It seems Renesas are churning out new SoCs by the minute. - A bunch of non-critical fixes for the Rockchip driver. - Improve the use of library functions instead of open coding. - Support the MCP28018 variant in the MCP28x08 driver. - Static constifying" * tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits) pinctrl: gemini: Fix missing pad descriptions pinctrl: Add some depends on HAS_IOMEM pinctrl: samsung/s3c24xx: add CONFIG_OF dependency pinctrl: gemini: Fix GMAC groups pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support pinctrl: ti-iodelay: remove redundant unused variable dev pinctrl: max77620: Use common error handling code in max77620_pinconf_set() pinctrl: gemini: Implement clock skew/delay config pinctrl: gemini: Use generic DT parser pinctrl: Add skew-delay pin config and bindings pinctrl: armada-37xx: Add edge both type gpio irq support pinctrl: uniphier: remove eMMC hardware reset pin-mux pinctrl: rockchip: Add iomux-route switching support for rk3288 pinctrl: intel: Add Intel Cedar Fork PCH pin controller support pinctrl: intel: Make offset to interrupt status register configurable pinctrl: sunxi: Enforce the strict mode by default pinctrl: sunxi: Disable strict mode for old pinctrl drivers pinctrl: sunxi: Introduce the strict flag pinctrl: sh-pfc: Save/restore registers for PSCI system suspend pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description ...
2017-11-14Merge tag 'gpio-v4.15-1' of ↵Linus Torvalds
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio Pull GPIO updates from Linus Walleij: "This is the bulk of GPIO changes for the v4.15 kernel cycle: Core: - Fix the semantics of raw GPIO to actually be raw. No inversion semantics as before, but also no open draining, and allow the raw operations to affect lines used for interrupts as the caller supposedly knows what they are doing if they are getting the big hammer. - Rewrote the __inner_function() notation calls to names that make more sense. I just find this kind of code disturbing. - Drop the .irq_base() field from the gpiochip since now all IRQs are mapped dynamically. This is nice. - Support for .get_multiple() in the core driver API. This allows us to read several GPIO lines with a single register read. This has high value for some usecases: it can be used to create oscilloscopes and signal analyzers and other things that rely on reading several lines at exactly the same instant. Also a generally nice optimization. This uses the new assign_bit() macro from the bitops lib that was ACKed by Andrew Morton and is implemented for two drivers, one of them being the generic MMIO driver so everyone using that will be able to benefit from this. - Do not allow requests of Open Drain and Open Source setting of a GPIO line simultaneously. If the hardware actually supports enabling both at the same time the electrical result would be disastrous. - A new interrupt chip core helper. This will be helpful to deal with "banked" GPIOs, which means GPIO controllers with several logical blocks of GPIO inside them. This is several gpiochips per device in the device model, in contrast to the case when there is a 1-to-1 relationship between a device and a gpiochip. New drivers: - Maxim MAX3191x industrial serializer, a very interesting piece of professional I/O hardware. - Uniphier GPIO driver. This is the GPIO block from the recent Socionext (ex Fujitsu and Panasonic) platform. - Tegra 186 driver. This is based on the new banked GPIO infrastructure. Other improvements: - Some documentation improvements. - Wakeup support for the DesignWare DWAPB GPIO controller. - Reset line support on the DesignWare DWAPB GPIO controller. - Several non-critical bug fixes and improvements for the Broadcom BRCMSTB driver. - Misc non-critical bug fixes like exotic errorpaths, removal of dead code etc. - Explicit comments on fall-through switch() statements" * tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits) gpio: tegra186: Remove tegra186_gpio_lock_class gpio: rcar: Add r8a77995 (R-Car D3) support pinctrl: bcm2835: Fix some merge fallout gpio: Fix undefined lock_dep_class gpio: Automatically add lockdep keys gpio: Introduce struct gpio_irq_chip.first gpio: Disambiguate struct gpio_irq_chip.nested gpio: Add Tegra186 support gpio: Export gpiochip_irq_{map,unmap}() gpio: Implement tighter IRQ chip integration gpio: Move lock_key into struct gpio_irq_chip gpio: Move irq_valid_mask into struct gpio_irq_chip gpio: Move irq_nested into struct gpio_irq_chip gpio: Move irq_chained_parent to struct gpio_irq_chip gpio: Move irq_default_type to struct gpio_irq_chip gpio: Move irq_handler to struct gpio_irq_chip gpio: Move irqdomain into struct gpio_irq_chip gpio: Move irqchip into struct gpio_irq_chip gpio: Introduce struct gpio_irq_chip pinctrl: armada-37xx: remove unused variable ...
2017-11-09Merge branch 'gpio-irqchip-rework' of /home/linus/linux-gpio into develLinus Walleij
2017-11-09pinctrl: bcm2835: Fix some merge falloutLinus Walleij
Fixing a small merge problem in BCM2835 related to the new irqchip code. Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-08gpio: Move irqdomain into struct gpio_irq_chipThierry Reding
In order to consolidate the multiple ways to associate an IRQ chip with a GPIO chip, move more fields into the new struct gpio_irq_chip. Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Grygorii Strashko <grygorii.strashko@ti.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-11-02License cleanup: add SPDX GPL-2.0 license identifier to files with no licenseGreg Kroah-Hartman
Many source files in the tree are missing licensing information, which makes it harder for compliance tools to determine the correct license. By default all files without license information are under the default license of the kernel, which is GPL version 2. Update the files which contain no license information with the 'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally binding shorthand, which can be used instead of the full boiler plate text. This patch is based on work done by Thomas Gleixner and Kate Stewart and Philippe Ombredanne. How this work was done: Patches were generated and checked against linux-4.14-rc6 for a subset of the use cases: - file had no licensing information it it. - file was a */uapi/* one with no licensing information in it, - file was a */uapi/* one with existing licensing information, Further patches will be generated in subsequent months to fix up cases where non-standard license headers were used, and references to license had to be inferred by heuristics based on keywords. The analysis to determine which SPDX License Identifier to be applied to a file was done in a spreadsheet of side by side results from of the output of two independent scanners (ScanCode & Windriver) producing SPDX tag:value files created by Philippe Ombredanne. Philippe prepared the base worksheet, and did an initial spot review of a few 1000 files. The 4.13 kernel was the starting point of the analysis with 60,537 files assessed. Kate Stewart did a file by file comparison of the scanner results in the spreadsheet to determine which SPDX license identifier(s) to be applied to the file. She confirmed any determination that was not immediately clear with lawyers working with the Linux Foundation. Criteria used to select files for SPDX license identifier tagging was: - Files considered eligible had to be source code files. - Make and config files were included as candidates if they contained >5 lines of source - File already had some variant of a license header in it (even if <5 lines). All documentation files were explicitly excluded. The following heuristics were used to determine which SPDX license identifiers to apply. - when both scanners couldn't find any license traces, file was considered to have no license information in it, and the top level COPYING file license applied. For non */uapi/* files that summary was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 11139 and resulted in the first patch in this series. If that file was a */uapi/* path one, it was "GPL-2.0 WITH Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was: SPDX license identifier # files ---------------------------------------------------|------- GPL-2.0 WITH Linux-syscall-note 930 and resulted in the second patch in this series. - if a file had some form of licensing information in it, and was one of the */uapi/* ones, it was denoted with the Linux-syscall-note if any GPL family license was found in the file or had no licensing in it (per prior point). Results summary: SPDX license identifier # files ---------------------------------------------------|------ GPL-2.0 WITH Linux-syscall-note 270 GPL-2.0+ WITH Linux-syscall-note 169 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21 ((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17 LGPL-2.1+ WITH Linux-syscall-note 15 GPL-1.0+ WITH Linux-syscall-note 14 ((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5 LGPL-2.0+ WITH Linux-syscall-note 4 LGPL-2.1 WITH Linux-syscall-note 3 ((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3 ((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1 and that resulted in the third patch in this series. - when the two scanners agreed on the detected license(s), that became the concluded license(s). - when there was disagreement between the two scanners (one detected a license but the other didn't, or they both detected different licenses) a manual inspection of the file occurred. - In most cases a manual inspection of the information in the file resulted in a clear resolution of the license that should apply (and which scanner probably needed to revisit its heuristics). - When it was not immediately clear, the license identifier was confirmed with lawyers working with the Linux Foundation. - If there was any question as to the appropriate license identifier, the file was flagged for further research and to be revisited later in time. In total, over 70 hours of logged manual review was done on the spreadsheet to determine the SPDX license identifiers to apply to the source files by Kate, Philippe, Thomas and, in some cases, confirmation by lawyers working with the Linux Foundation. Kate also obtained a third independent scan of the 4.13 code base from FOSSology, and compared selected files where the other two scanners disagreed against that SPDX file, to see if there was new insights. The Windriver scanner is based on an older version of FOSSology in part, so they are related. Thomas did random spot checks in about 500 files from the spreadsheets for the uapi headers and agreed with SPDX license identifier in the files he inspected. For the non-uapi files Thomas did random spot checks in about 15000 files. In initial set of patches against 4.14-rc6, 3 files were found to have copy/paste license identifier errors, and have been fixed to reflect the correct identifier. Additionally Philippe spent 10 hours this week doing a detailed manual inspection and review of the 12,461 patched files from the initial patch version early this week with: - a full scancode scan run, collecting the matched texts, detected license ids and scores - reviewing anything where there was a license detected (about 500+ files) to ensure that the applied SPDX license was correct - reviewing anything where there was no detection but the patch license was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied SPDX license was correct This produced a worksheet with 20 files needing minor correction. This worksheet was then exported into 3 different .csv files for the different types of files to be modified. These .csv files were then reviewed by Greg. Thomas wrote a script to parse the csv files and add the proper SPDX tag to the file, in the format that the file expected. This script was further refined by Greg based on the output to detect more types of files automatically and to distinguish between header and source .c files (which need different comment types.) Finally Greg ran the script using the .csv files to generate the patches. Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com> Reviewed-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-10-07pinctrl: bcm: nsp: Use library functionsLinus Walleij
These request/free functions are just reimplementations of the standard helpers in gpiolib. Delete them and replace with the helpers. Acked-by: Scott Branden <scott.branden@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-09-22pinctrl/gpio: Unify namespace for cross-callsLinus Walleij
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice namespacing in the other cross-calls like pinctrl_gpio_foo(). Just rename them and all references so we have one namespace with all cross-calls under pinctrl_gpio_*(). Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-09-21pinctrl: bcm2835: fix build warning in bcm2835_gpio_irq_handle_bankCorentin Labbe
This patch fix the following build warning: drivers/pinctrl/bcm/pinctrl-bcm2835.c:376:15: warning: variable 'type' set but not used [-Wunused-but-set-variable] Furthermore, it is unused for a long time, at least since commit 85ae9e512f43 ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP") where a "FIXME no clue why the code looks up the type here" was added. A year after, nobody answeered this question, so its time to remove it. Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com> Acked-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-22pinctrl: bcm281xx: constify pinconf_ops, pinctrl_ops, and pinmux_ops structuresJulia Lawall
This pinconf_ops structure is only stored in the const confops field of a pinctrl_desc structure. Make the pinconf_ops structure const as well. Done with the help of Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14pinctrl: bcm2835: Remove unneeded irq_group fieldThierry Reding
The irq_group field stores a 1:1 mapping. Use the loop variable to derive the values instead of storing them in an extra array. Signed-off-by: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14pinctrl: Convert to using %pOF instead of full_nameRob Herring
Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Lee Jones <lee@kernel.org> Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: Tomasz Figa <tomasz.figa@gmail.com> Cc: Sylwester Nawrocki <s.nawrocki@samsung.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Barry Song <baohua@kernel.org> Cc: linux-gpio@vger.kernel.org Cc: linux-rpi-kernel@lists.infradead.org Cc: linux-arm-kernel@lists.infradead.org Cc: kernel@stlinux.com Cc: linux-samsung-soc@vger.kernel.org Cc: linux-renesas-soc@vger.kernel.org Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com> Acked-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-08-14pinctrl: bcm2835: constify gpio_chip structureGustavo A. R. Silva
This structure is only used to copy into other structure, so declare it as const. This issue was detected using Coccinelle and the following semantic patch: @r disable optional_qualifier@ identifier i; position p; @@ static struct gpio_chip i@p = { ... }; @ok@ identifier r.i; expression e; position p; @@ e = i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct gpio_chip e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct gpio_chip i = { ... }; In the following log you can see a significant difference in the code size and data segment, hence in the dec segment. This log is the output of the size command, before and after the code change: before: text data bss dec hex filename 18958 9000 128 28086 6db6 drivers/pinctrl/bcm/pinctrl-bcm2835.o after: text data bss dec hex filename 18764 8912 128 27804 6c9c drivers/pinctrl/bcm/pinctrl-bcm2835.o Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-29pinctrl: bcm2835: Avoid warning from __irq_do_set_handlerStefan Wahren
We get a warning during boot with enabled EARLY_PRINTK that we try to set a irq_chip without data. This is caused by ignoring the return value of irq_of_parse_and_map(). So avoid calling gpiochip_set_chained_irqchip() in error case. Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Fixes: 85ae9e512f43 ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP") Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-06-09pinctrl: bcm: cleanup Broadcom license headersScott Branden
Use consistent license headers for Broadcom files by placing additional comments outside of standard legal header. Also, update legal header to 2017 format as "Broadcom Corporation" has changed to "Broadcom". Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-05-29pinctrl: bcm: clean up modular vs. non-modular distinctionsPaul Gortmaker
Fixups here tend to be more of a conglomerate of some of the other repeated/systematic ones we've seen in the earlier pinctrl cleanups. We remove module.h from code that isn't doing anything modular at all; if they have __init sections, then replace it with init.h One driver has a .remove that would be dispatched on module_exit, and as that code is essentially orphaned, so we remove it. In case anyone was previously doing the (pointless) unbind to get to that function, we disable unbind for this one driver as well. A couple bool drivers (hence non-modular) are converted over to to builtin_platform_driver(). Since module_platform_driver() uses the same init level priority as builtin_platform_driver() the init ordering remains unchanged with this commit. Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code. We also delete the MODULE_LICENSE tag etc. since all that information was (or is now) contained at the top of the file in the comments. Cc: Eric Anholt <eric@anholt.net> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Jon Mason <jonmason@broadcom.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Ray Jui <rjui@broadcom.com> Cc: Scott Branden <sbranden@broadcom.com> Cc: Sherman Yin <syin@broadcom.com> Cc: bcm-kernel-feedback-list@broadcom.com Cc: linux-gpio@vger.kernel.org Cc: linux-rpi-kernel@lists.infradead.org Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-03-16pinctrl: bcm: make use of raw_spinlock variantsJulia Cartwright
The bcm pinctrl drivers currently implement an irq_chip for handling interrupts; due to how irq_chip handling is done, it's necessary for the irq_chip methods to be invoked from hardirq context, even on a a real-time kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT kernels, it is not suitable to be used with irq_chips. A quick audit of the operations under the lock reveal that they do only minimal, bounded work, and are therefore safe to do under a raw spinlock. Signed-off-by: Julia Cartwright <julia@ni.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2017-02-27scripts/spelling.txt: add "overrided" pattern and fix typo instancesMasahiro Yamada
Fix typos and add the following to the scripts/spelling.txt: overrided||overridden Link: http://lkml.kernel.org/r/1481573103-11329-22-git-send-email-yamada.masahiro@socionext.com Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2017-01-26pinctrl: Widen the generic pinconf argument from 16 to 24 bitsMika Westerberg
The current pinconf packed format allows only 16-bit argument limiting the maximum value 65535. For most types this is enough. However, debounce time can be in range of hundreths of milliseconds in case of mechanical switches so we cannot represent the worst case using the current format. In order to support larger values change the packed format so that the lower 8 bits are used as type which leaves 24 bits for the argument. This allows representing values up to 16777215 and debounce times up to 16 seconds. We also convert the existing users to use 32-bit integer when extracting argument from the packed configuration value. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-12-15Merge tag 'armsoc-dt' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM DT updates from Arnd Bergmann: "Lots of changes as usual, so I'm trying to be brief here. Most of the new hardware support has the respective driver changes merged through other trees or has had it available for a while, so this is where things come together. We get a DT descriptions for a couple of new SoCs, all of them variants of other chips we already support, and usually coming with a new evaluation board: - Oxford semiconductor (now Broadcom) OX820 SoC for NAS devices - Qualcomm MDM9615 LTE baseband - NXP imx6ull, the latest and smallest i.MX6 application processor variant - Renesas RZ/G (r8a7743 and r8a7745) application processors - Rockchip PX3, a variant of the rk3188 chip used in Android tablets - Rockchip rk1108 single-core application processor - ST stm32f746 Cortex-M7 based microcontroller - TI DRA71x automotive processors These are commercially available consumer platforms we now support: - Motorola Droid 4 (xt894) mobile phone - Rikomagic MK808 Android TV stick based on Rockchips rx3066 - Cloud Engines PogoPlug v3 based on OX820 - Various Broadcom based wireless devices: - Netgear R8500 router - Tenda AC9 router - TP-LINK Archer C9 V1 - Luxul XAP-1510 Access point - Turris Omnia open hardware router based on Armada 385 And a couple of new boards targeted at developers, makers or industrial integration: - Macnica Sodia development platform for Altera socfpga (Cyclone V) - MicroZed board based on Xilinx Zynq FPGA platforms - TOPEET itop/elite based on exynos4412 - WP8548 MangOH Open Hardware platform for IOT, based on Qualcomm MDM9615 - NextThing CHIP Pro gadget - NanoPi M1 development board - AM571x-IDK industrial board based on TI AM5718 - i.MX6SX UDOO Neo - Boundary Devices Nitrogen6_SOM2 (i.MX6) - Engicam i.CoreM6 - Grinn i.MX6UL liteSOM/liteBoard - Toradex Colibri iMX6 module Other changes: - added peripherals on renesas, davinci, stm32f429, uniphier, sti, mediatek, integrator, at91, imx, vybrid, ls1021a, omap, qualcomm, mvebu, allwinner, broadcom, exynos, zynq - Continued fixes for W=1 dtc warnings - The old STiH415/416 SoC support gets removed, these never made it into products and have served their purpose in the kernel as a template for teh newer chips from ST - The exynos4415 dtsi file is removed as nothing uses it. - Intel PXA25x can now be booted using devicetree" * tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (422 commits) arm: dts: zynq: Add MicroZed board support ARM: dts: da850: enable high speed for mmc ARM: dts: da850: Add node for pullup/pulldown pinconf ARM: dts: da850: enable memctrl and mstpri nodes per board ARM: dts: da850-lcdk: Add ethernet0 alias to DT ARM: dts: artpec: add pcie support ARM: dts: add support for Turris Omnia devicetree: Add vendor prefix for CZ.NIC ARM: dts: berlin2q-marvell-dmp: fix typo in chosen node ARM: dts: berlin2q-marvell-dmp: fix regulators' name ARM: dts: Add xo to sdhc clock node on qcom platforms ARM: dts: r8a7794: Add device node for PRR ARM: dts: r8a7793: Add device node for PRR ARM: dts: r8a7792: Add device node for PRR ARM: dts: r8a7791: Add device node for PRR ARM: dts: r8a7790: Add device node for PRR ARM: dts: r8a7779: Add device node for PRR ARM: dts: r8a73a4: Add device node for PRR ARM: dts: sk-rzg1e: add Ether support ARM: dts: sk-rzg1e: initial device tree ...
2016-12-13Merge tag 'pinctrl-v4.10-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl Pull pinctrl updates from Linus Walleij: "Bulk pin control changes for the v4.10 kernel cycle: No core changes this time. Mainly gradual improvement and feature growth in the drivers. New drivers: - New driver for TI DA850/OMAP-L138/AM18XX pinconf - The SX150x was moved over from the GPIO subsystem and reimagined as a pin control driver with GPIO support in a joint effort by three independent users of this hardware. The result was amazingly good! - New subdriver for the Oxnas OX820 Improvements: - The sunxi driver now supports the generic pin control bindings rather than the sunxi-specific. Add debouncing support to the driver. - Simplifications in pinctrl-single adding a generic parser. - Two downstream fixes and move the Raspberry Pi BCM2835 over to use the generic GPIOLIB_IRQCHIP" * tag 'pinctrl-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (92 commits) pinctrl: sx150x: use new nested IRQ infrastructure pinctrl: sx150x: handle missing 'advanced' reg in sx1504 and sx1505 pinctrl: sx150x: rename 'reg_advance' to 'reg_advanced' pinctrl: sx150x: access the correct bits in the 4-bit regs of sx150[147] pinctrl: mt8173: set GPIO16 to usb iddig mode pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP pinctrl: New driver for TI DA850/OMAP-L138/AM18XX pinconf devicetree: bindings: pinctrl: Add binding for ti,da850-pupd Documentation: pinctrl: palmas: Add ti,palmas-powerhold-override property definition pinctrl: intel: set default handler to be handle_bad_irq() pinctrl: sx150x: add support for sx1501, sx1504, sx1505 and sx1507 pinctrl: sx150x: sort chips by part number pinctrl: sx150x: use correct registers for reg_sense (sx1502 and sx1508) pinctrl: imx: fix imx_pinctrl_desc initialization pinctrl: sx150x: support setting multiple pins at once pinctrl: sx150x: various spelling fixes and some white-space cleanup pinctrl: mediatek: use builtin_platform_driver pinctrl: stm32: use builtin_platform_driver pinctrl: sunxi: Testing the wrong variable pinctrl: nomadik: split up and comments MC0 pins ...
2016-12-07pinctrl: bcm2835: switch to GPIOLIB_IRQCHIPLinus Walleij
It should be possible to use the GPIOLIB_IRQCHIP helper library with the BCM2835 driver since it is a pretty straight forward cascaded irqchip. The only difference from other drivers is that the BCM2835 has several banks for a single gpiochip, and each bank has a separate IRQ line. Instead of creating one gpiochip per bank, a single gpiochip covers all banks GPIO lines. This makes it necessary to resolve the bank ID in the IRQ handler. The GPIOLIB_IRQCHIP allows several IRQs to be cascaded off the same gpiochip by calling gpiochip_set_chained_irqchip() repeatedly, but we have been a bit short on examples for how this should be handled in practice, so this is intended as an example of how this can be achieved. The old code did not model the chip as a chained interrupt handler, but this patch also rectifies that situation. Cc: Stephen Warren <swarren@wwwdotorg.org> Tested-by: Stefan Wahren <stefan.wahren@i2se.com> Tested-by: Eric Anholt <eric@anholt.net> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-15pinctrl: bcm2835: Return pins to inputs when freedPhil Elwell
When dynamically unloading overlays, it is important that freed pins are restored to being inputs to prevent functions from being enabled in multiple places at once. Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Phil Elwell <phil@raspberrypi.org> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-15pinctrl: bcm2835: Fix ints for GPIOs 28-31 & 46-53Phil Elwell
Contrary to the documentation, the BCM2835 GPIO controller actually has four interrupt lines - one each for the three IRQ groups and one common. Confusingly, the GPIO interrupt groups don't correspond directly with the GPIO control banks. Instead, GPIOs 0-27 generate IRQ GPIO0, 28-45 IRQ GPIO1 and 46-53 IRQ GPIO2. Awkwardly, the GPIOs for IRQ GPIO1 straddle two 32-entry GPIO banks, so split out a function to process the interrupts for a single GPIO bank. Cc: Stefan Wahren <stefan.wahren@i2se.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Signed-off-by: Phil Elwell <phil@raspberrypi.org> Acked-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-11-04pinctrl: bcm2835: reduce GPPUD set-up timeStefan Wahren
Since the BCM2835 datasheet doesn't exactly specify the set-up time for the GPIO Pull-up/down Clock Registers there was an assumption of 150 cycles at a clock rate of 1 MHz. During a discussion [1] in the Raspberry Pi forum it turns out that clock rate refers to the VPU which has a rate of 250 MHz. So we can reduce the delay to a sensible value and update the comment above. I tested this optimization with a Raspberry Pi B and a multimeter. [1] - https://www.raspberrypi.org/forums/viewtopic.php?f=72&t=163352 Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Reviewed-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-31pinctrl: iproc: Fix iProc and NSP GPIO supportRay Jui
Since commit 44a7185c2ae6 ("of/platform: Add common method to populate default bus"), ARM64 platform devices are populated at the arch_initcall_sync level; as a result, the platform_driver_probe calls in both the iProc and NSP GPIO drivers fail with -ENODEV since by that time the platform device was not yet registered. Replace platform_driver_probe with platform_driver_register, that allow the device to be register later Fixes: 44a7185c2ae6 ("of/platform: Add common method to populate default bus") Signed-off-by: Ray Jui <ray.jui@broadcom.com> Tested-by: Eric Anholt <eric@anholt.net> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-10-17pinctrl: bcm2835: add pull defines to dt bindingsGerd Hoffmann
Also delete (unused) private enum from driver. The pull defines can be used instead if needed. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com> Signed-off-by: Eric Anholt <eric@anholt.net> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
2016-09-07pinctrl: bcm281xx: constify pinctrl_ops and pinmux_ops structuresJulia Lawall
Check for pinctrl_ops and pinmux_ops structures that are only stored in the pctlops field and the pmxops field, respectively, of a pinctrl_desc structure. These fields are declared const, so pinctrl_ops and pinmux_ops structures that have this property can be declared as const also. The semantic patch that makes this change in the pinctrl_ops is as follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/) // <smpl> @r disable optional_qualifier@ identifier i; position p; @@ static struct pinctrl_ops i@p = { ... }; @ok@ identifier r.i; struct pinctrl_desc e; position p; @@ e.pctlops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct pinctrl_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct pinctrl_ops i = { ... }; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-07pinctrl: nsp: constify pinctrl_ops and pinmux_ops structuresJulia Lawall
Check for pinctrl_ops and pinmux_ops structures that are only stored in the pctlops field and the pmxops field, respectively, of a pinctrl_desc structure. These fields are declared const, so pinctrl_ops and pinmux_ops structures that have this property can be declared as const also. The semantic patch that makes this change in the pinctrl_ops is as follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/) // <smpl> @r disable optional_qualifier@ identifier i; position p; @@ static struct pinctrl_ops i@p = { ... }; @ok@ identifier r.i; struct pinctrl_desc e; position p; @@ e.pctlops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct pinctrl_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct pinctrl_ops i = { ... }; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-09-07pinctrl: ns2: constify pinctrl_ops and pinmux_ops structuresJulia Lawall
Check for pinctrl_ops and pinmux_ops structures that are only stored in the pctlops field and the pmxops field, respectively, of a pinctrl_desc structure. These fields are declared const, so pinctrl_ops and pinmux_ops structures that have this property can be declared as const also. The semantic patch that makes this change in the pinctrl_ops is as follows. The pinmux_ops case is similar. (http://coccinelle.lip6.fr/) // <smpl> @r disable optional_qualifier@ identifier i; position p; @@ static struct pinctrl_ops i@p = { ... }; @ok@ identifier r.i; struct pinctrl_desc e; position p; @@ e.pctlops = &i@p; @bad@ position p != {r.p,ok.p}; identifier r.i; struct pinctrl_ops e; @@ e@i@p @depends on !bad disable optional_qualifier@ identifier r.i; @@ static +const struct pinctrl_ops i = { ... }; // </smpl> Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-07-22pinctrl: iproc: Add NSP and Stingray GPIO supportRay Jui
The iProc GPIO controller is shared among multiple iProc based SoCs. In the NSP integration, the drive strength pinctrl function is disabled. In the integration of Stingray, pinctrl is handled by another block and this GPIO controller is solely used as a GPIO controller, and therefore should not be registered to the pinconf framework This patch introduces new SoC specific compatible strings "brcm,iproc-nsp-gpio" for NSP with drive strength feature disabled and "brcm,iproc-stingray-gpio" for Stingray with all PINCONF features disabled This patch is developed based on the initial work from Yendapally Reddy Dhananjaya <yendapally.reddy@broadcom.com> who attempted to disable drive strength configuration for the iProc based NSP chip. In addition, Pramod Kumar <pramod.kumar@broadcom.com> also contributed to make the support more generic across all currently supported PINCONF functions in the iProc GPIO/PINCONF driver Signed-off-by: Pramod Kumar <pramodku@broadcom.com> Signed-off-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-07-22pinctrl: bcm: add OF dependenciesArnd Bergmann
Building without CONFIG_OF gives us these warnings for the broadcom pinctrl drivers: drivers/pinctrl/bcm/pinctrl-nsp-mux.c:356:20: error: 'pinconf_generic_dt_node_to_map_group' undeclared here (not in a function) drivers/pinctrl/bcm/pinctrl-cygnus-mux.c:739:20: error: 'pinconf_generic_dt_node_to_map_group' undeclared here (not in a function) The function is only available when CONFIG_OF is set, so we should add a Kconfig dependency for both drivers. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC") Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-07-22pinctrl: ns2: remove redundant dev_err call in ns2_pinmux_probe()Wei Yongjun
There is a error message within devm_ioremap_resource already, so remove the dev_err call to avoid redundant error message. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-07-11pinctrl: nsp: remove redundant dev_err call in nsp_pinmux_probe()Wei Yongjun
There is a error message within devm_ioremap_resource already, so remove the dev_err call to avoid redundant error message. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Acked-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-07-11pinctrl: ns2: fix return value check in ns2_pinmux_probe()Wei Yongjun
In case of error, the function pinctrl_register() returns NULL not ERR_PTR(). The IS_ERR() test in the return value check should be replaced with NULL test. Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-06-29pinctrl: nsp: add pinmux driver support for Broadcom NSP SoCYendapally Reddy Dhananjaya Reddy
This adds the initial support of the Broadcom NSP pinmux driver. Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Reviewed-by: Ray Jui <rjui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-06-08pinctrl: nsp-gpio: fix non-static functionsBen Dooks
Fixup warnings from functions that are not exported and therefore should be marked static. Fixes: drivers/pinctrl/bcm/pinctrl-nsp-gpio.c:461:5: warning: symbol 'nsp_pin_config_group_get' was not declared. Should it be static? drivers/pinctrl/bcm/pinctrl-nsp-gpio.c:467:5: warning: symbol 'nsp_pin_config_group_set' was not declared. Should it be static? Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk> Acked-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-05-09pinctrl: ns2: rename pinctrl_utils_dt_free_mapArnd Bergmann
A conflict of two patches caused a build error when a function got renamed but a new user appeared in the other patch: drivers/pinctrl/bcm/pinctrl-ns2-mux.c:540:17: error: 'pinctrl_utils_dt_free_map' undeclared here (not in a function) .dt_free_map = pinctrl_utils_dt_free_map, ^~~~~~~~~~~~~~~~~~~~~~~~~ This renames the new user of pinctrl_utils_dt_free_map accordingly. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: d32f7fd3bbc3 ("pinctrl: Rename pinctrl_utils_dt_free_map to pinctrl_utils_free_map") Fixes: b5aa1006e4a9 ("pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoC") Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2016-04-30pinctrl: ns2: add pinmux driver support for Broadcom NS2 SoCYendapally Reddy Dhananjaya Reddy
This adds the initial support of the Broadcom NS2 pinmux driver Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit v1.2.3-58-ga151 (git 2.39.0) at 2024-12-22 22:12:29 +0000