| Age | Commit message (Collapse) | Author |
|---|
|
Commit 287422a95fe2 ("drm/rockchip: Round up _before_ giving to the clock framework")
changed what rate clk_round_rate() is called with, an additional 999 Hz
added to the requsted mode clock. This has caused a regression on RK3328
and presumably also on RK3228 because the inno-hdmi-phy clock requires an
exact match of the requested rate in the pre pll config table.
When an exact match is not found the parent clock rate (24MHz) is returned
to the clk_round_rate() caller. This cause wrong pixel clock to be used and
result in no-signal when configuring a mode on RK3328.
Fix this by rounding the rate down to closest 1000 Hz in round_rate func,
this allows an exact match to be found in pre pll config table.
Fixes: 287422a95fe2 ("drm/rockchip: Round up _before_ giving to the clock framework")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We are currently writing the same register twice. Let's enable the USB
PHY only at the end of the function.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
When docked to a Motorola lapdock or media dock, we're in USB A-host mode
with VBUS provided by the dock. When in regular USB A-host mode, we're
providing the VBUS. And in regular USB A-host mode we must also keep
kicking the VBUS to keep it active.
Let's wait a bit before configuring the USB PHY to allow some time between
the ID and VBUS changes. And let's add vbus_provider flag so we can detect
docked mode and regularo USB A-host mode better.
With better USB A-host mode detection, we can now also just kick the
VBUS to keep it enabled and leave out the unnecessary line muxing.
We only need to set and clear vbus_provider in the delayed work so no
locking is needed for it currently.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The micro-USB connector on Motorola Mapphone devices can be muxed between
the SoC and the mdm6600 modem. But even when used for the SoC, configuring
the PHY with ID pin grounded will wake up the modem from idle state. Looks
like the issue is probably caused by line glitches.
We can prevent the glitches by using a previously unknown mode of the
GPIO mux to prevent the USB lines from being connected to the moden while
configuring the USB PHY, and enable the USB lines after configuring the
PHY.
Note that this only prevents waking up mdm6600 as regular USB A-host mode,
and does not help when connected to a lapdock. The lapdock specific issue
still needs to be debugged separately.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Only the used bits get cleared with bitmap_zero() when we call
gpiod_get_array_value_cansleep(). We must mask only the bits we're
using for ddata->status as the other bits in the bitmap may not be
initialized.
And let's also drop useless debug code accidentally left over while
at it.
Fixes: b9762bebc633 ("gpiolib: Pass bitmaps, not integer arrays, to get/set array")
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
We must let the USB host idle things properly before we switch to debug
UART mode. Otherwise the USB host may never idle after disconnecting
devices, and that causes the next enumeration to be flakey.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
It's typical for the QHP PHY to take slightly above 1ms to initialize,
so increase the timeout of the PHY ready check to 10ms - as already done
in the downstream PCIe driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Evan Green <evgreen@chromium.org>
Tested-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
If musb_mailbox() returns an error, we must still continue to finish
configuring the phy.
Otherwise the phy state may end up only half initialized, and this can
cause the debug serial console to stop working. And this will happen if the
usb driver musb controller is not loaded.
Let's fix the issue by adding helper for cpcap_usb_try_musb_mailbox().
Fixes: 6d6ce40f63af ("phy: cpcap-usb: Add CPCAP PMIC USB support")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Warn if a host bridge has no NUMA info (Yunsheng Lin)
- Add PCI_STD_NUM_BARS for the number of standard BARs (Denis
Efremov)
Resource management:
- Fix boot-time Embedded Controller GPE storm caused by incorrect
resource assignment after ACPI Bus Check Notification (Mika
Westerberg)
- Protect pci_reassign_bridge_resources() against concurrent
addition/removal (Benjamin Herrenschmidt)
- Fix bridge dma_ranges resource list cleanup (Rob Herring)
- Add "pci=hpmmiosize" and "pci=hpmmioprefsize" parameters to control
the MMIO and prefetchable MMIO window sizes of hotplug bridges
independently (Nicholas Johnson)
- Fix MMIO/MMIO_PREF window assignment that assigned more space than
desired (Nicholas Johnson)
- Only enforce bus numbers from bridge EA if the bridge has EA
devices downstream (Subbaraya Sundeep)
- Consolidate DT "dma-ranges" parsing and convert all host drivers to
use shared parsing (Rob Herring)
Error reporting:
- Restore AER capability after resume (Mayurkumar Patel)
- Add PoisonTLPBlocked AER counter (Rajat Jain)
- Use for_each_set_bit() to simplify AER code (Andy Shevchenko)
- Fix AER kernel-doc (Andy Shevchenko)
- Add "pcie_ports=dpc-native" parameter to allow native use of DPC
even if platform didn't grant control over AER (Olof Johansson)
Hotplug:
- Avoid returning prematurely from sysfs requests to enable or
disable a PCIe hotplug slot (Lukas Wunner)
- Don't disable interrupts twice when suspending hotplug ports (Mika
Westerberg)
- Fix deadlocks when PCIe ports are hot-removed while suspended (Mika
Westerberg)
Power management:
- Remove unnecessary ASPM locking (Bjorn Helgaas)
- Add support for disabling L1 PM Substates (Heiner Kallweit)
- Allow re-enabling Clock PM after it has been disabled (Heiner
Kallweit)
- Add sysfs attributes for controlling ASPM link states (Heiner
Kallweit)
- Remove CONFIG_PCIEASPM_DEBUG, including "link_state" and "clk_ctl"
sysfs files (Heiner Kallweit)
- Avoid AMD FCH XHCI USB PME# from D0 defect that prevents wakeup on
USB 2.0 or 1.1 connect events (Kai-Heng Feng)
- Move power state check out of pci_msi_supported() (Bjorn Helgaas)
- Fix incorrect MSI-X masking on resume and revert related nvme quirk
for Kingston NVME SSD running FW E8FK11.T (Jian-Hong Pan)
- Always return devices to D0 when thawing to fix hibernation with
drivers like mlx4 that used legacy power management (previously we
only did it for drivers with new power management ops) (Dexuan Cui)
- Clear PCIe PME Status even for legacy power management (Bjorn
Helgaas)
- Fix PCI PM documentation errors (Bjorn Helgaas)
- Use dev_printk() for more power management messages (Bjorn Helgaas)
- Apply D2 delay as milliseconds, not microseconds (Bjorn Helgaas)
- Convert xen-platform from legacy to generic power management (Bjorn
Helgaas)
- Removed unused .resume_early() and .suspend_late() legacy power
management hooks (Bjorn Helgaas)
- Rearrange power management code for clarity (Rafael J. Wysocki)
- Decode power states more clearly ("4" or "D4" really refers to
"D3cold") (Bjorn Helgaas)
- Notice when reading PM Control register returns an error (~0)
instead of interpreting it as being in D3hot (Bjorn Helgaas)
- Add missing link delays required by the PCIe spec (Mika Westerberg)
Virtualization:
- Move pci_prg_resp_pasid_required() to CONFIG_PCI_PRI (Bjorn
Helgaas)
- Allow VFs to use PRI (the PF PRI is shared by the VFs, but the code
previously didn't recognize that) (Kuppuswamy Sathyanarayanan)
- Allow VFs to use PASID (the PF PASID capability is shared by the
VFs, but the code previously didn't recognize that) (Kuppuswamy
Sathyanarayanan)
- Disconnect PF and VF ATS enablement, since ATS in PFs and
associated VFs can be enabled independently (Kuppuswamy
Sathyanarayanan)
- Cache PRI and PASID capability offsets (Kuppuswamy Sathyanarayanan)
- Cache the PRI PRG Response PASID Required bit (Bjorn Helgaas)
- Consolidate ATS declarations in linux/pci-ats.h (Krzysztof
Wilczynski)
- Remove unused PRI and PASID stubs (Bjorn Helgaas)
- Removed unnecessary EXPORT_SYMBOL_GPL() from ATS, PRI, and PASID
interfaces that are only used by built-in IOMMU drivers (Bjorn
Helgaas)
- Hide PRI and PASID state restoration functions used only inside the
PCI core (Bjorn Helgaas)
- Add a DMA alias quirk for the Intel VCA NTB (Slawomir Pawlowski)
- Serialize sysfs sriov_numvfs reads vs writes (Pierre Crégut)
- Update Cavium ACS quirk for ThunderX2 and ThunderX3 (George
Cherian)
- Fix the UPDCR register address in the Intel ACS quirk (Steffen
Liebergeld)
- Unify ACS quirk implementations (Bjorn Helgaas)
Amlogic Meson host bridge driver:
- Fix meson PERST# GPIO polarity problem (Remi Pommarel)
- Add DT bindings for Amlogic Meson G12A (Neil Armstrong)
- Fix meson clock names to match DT bindings (Neil Armstrong)
- Add meson support for Amlogic G12A SoC with separate shared PHY
(Neil Armstrong)
- Add meson extended PCIe PHY functions for Amlogic G12A USB3+PCIe
combo PHY (Neil Armstrong)
- Add arm64 DT for Amlogic G12A PCIe controller node (Neil Armstrong)
- Add commented-out description of VIM3 USB3/PCIe mux in arm64 DT
(Neil Armstrong)
Broadcom iProc host bridge driver:
- Invalidate iProc PAXB address mapping before programming it
(Abhishek Shah)
- Fix iproc-msi and mvebu __iomem annotations (Ben Dooks)
Cadence host bridge driver:
- Refactor Cadence PCIe host controller to use as a library for both
host and endpoint (Tom Joseph)
Freescale Layerscape host bridge driver:
- Add layerscape LS1028a support (Xiaowei Bao)
Intel VMD host bridge driver:
- Add VMD bus 224-255 restriction decode (Jon Derrick)
- Add VMD 8086:9A0B device ID (Jon Derrick)
- Remove Keith from VMD maintainer list (Keith Busch)
Marvell ARMADA 3700 / Aardvark host bridge driver:
- Use LTSSM state to build link training flag since Aardvark doesn't
implement the Link Training bit (Remi Pommarel)
- Delay before training Aardvark link in case PERST# was asserted
before the driver probe (Remi Pommarel)
- Fix Aardvark issues with Root Control reads and writes (Remi
Pommarel)
- Don't rely on jiffies in Aardvark config access path since
interrupts may be disabled (Remi Pommarel)
- Fix Aardvark big-endian support (Grzegorz Jaszczyk)
Marvell ARMADA 370 / XP host bridge driver:
- Make mvebu_pci_bridge_emul_ops static (Ben Dooks)
Microsoft Hyper-V host bridge driver:
- Add hibernation support for Hyper-V virtual PCI devices (Dexuan
Cui)
- Track Hyper-V pci_protocol_version per-hbus, not globally (Dexuan
Cui)
- Avoid kmemleak false positive on hv hbus buffer (Dexuan Cui)
Mobiveil host bridge driver:
- Change mobiveil csr_read()/write() function names that conflict
with riscv arch functions (Kefeng Wang)
NVIDIA Tegra host bridge driver:
- Fix Tegra CLKREQ dependency programming (Vidya Sagar)
Renesas R-Car host bridge driver:
- Remove unnecessary header include from rcar (Andrew Murray)
- Tighten register index checking for rcar inbound range programming
(Marek Vasut)
- Fix rcar inbound range alignment calculation to improve packing of
multiple entries (Marek Vasut)
- Update rcar MACCTLR setting to match documentation (Yoshihiro
Shimoda)
- Clear bit 0 of MACCTLR before PCIETCTLR.CFINIT per manual
(Yoshihiro Shimoda)
- Add Marek Vasut and Yoshihiro Shimoda as R-Car maintainers (Simon
Horman)
Rockchip host bridge driver:
- Make rockchip 0V9 and 1V8 power regulators non-optional (Robin
Murphy)
Socionext UniPhier host bridge driver:
- Set uniphier to host (RC) mode always (Kunihiko Hayashi)
Endpoint drivers:
- Fix endpoint driver sign extension problem when shifting page
number to phys_addr_t (Alan Mikhak)
Misc:
- Add NumaChip SPDX header (Krzysztof Wilczynski)
- Replace EXTRA_CFLAGS with ccflags-y (Krzysztof Wilczynski)
- Remove unused includes (Krzysztof Wilczynski)
- Removed unused sysfs attribute groups (Ben Dooks)
- Remove PTM and ASPM dependencies on PCIEPORTBUS (Bjorn Helgaas)
- Add PCIe Link Control 2 register field definitions to replace magic
numbers in AMDGPU and Radeon CIK/SI (Bjorn Helgaas)
- Fix incorrect Link Control 2 Transmit Margin usage in AMDGPU and
Radeon CIK/SI PCIe Gen3 link training (Bjorn Helgaas)
- Use pcie_capability_read_word() instead of pci_read_config_word()
in AMDGPU and Radeon CIK/SI (Frederick Lawler)
- Remove unused pci_irq_get_node() Greg Kroah-Hartman)
- Make asm/msi.h mandatory and simplify PCI_MSI_IRQ_DOMAIN Kconfig
(Palmer Dabbelt, Michal Simek)
- Read all 64 bits of Switchtec part_event_bitmap (Logan Gunthorpe)
- Fix erroneous intel-iommu dependency on CONFIG_AMD_IOMMU (Bjorn
Helgaas)
- Fix bridge emulation big-endian support (Grzegorz Jaszczyk)
- Fix dwc find_next_bit() usage (Niklas Cassel)
- Fix pcitest.c fd leak (Hewenliang)
- Fix typos and comments (Bjorn Helgaas)
- Fix Kconfig whitespace errors (Krzysztof Kozlowski)"
* tag 'pci-v5.5-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (160 commits)
PCI: Remove PCI_MSI_IRQ_DOMAIN architecture whitelist
asm-generic: Make msi.h a mandatory include/asm header
Revert "nvme: Add quirk for Kingston NVME SSD running FW E8FK11.T"
PCI/MSI: Fix incorrect MSI-X masking on resume
PCI/MSI: Move power state check out of pci_msi_supported()
PCI/MSI: Remove unused pci_irq_get_node()
PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer
PCI: hv: Change pci_protocol_version to per-hbus
PCI: hv: Add hibernation support
PCI: hv: Reorganize the code in preparation of hibernation
MAINTAINERS: Remove Keith from VMD maintainer
PCI/ASPM: Remove PCIEASPM_DEBUG Kconfig option and related code
PCI/ASPM: Add sysfs attributes for controlling ASPM link states
PCI: Fix indentation
drm/radeon: Prefer pcie_capability_read_word()
drm/radeon: Replace numbers with PCI_EXP_LNKCTL2 definitions
drm/radeon: Correct Transmit Margin masks
drm/amdgpu: Prefer pcie_capability_read_word()
PCI: uniphier: Set mode register to host mode
drm/amdgpu: Replace numbers with PCI_EXP_LNKCTL2 definitions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char/misc and other driver patches for 5.5-rc1
Loads of different things in here, this feels like the catch-all of
driver subsystems these days. Full details are in the shortlog, but
nothing major overall, just lots of driver updates and additions.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (198 commits)
char: Fix Kconfig indentation, continued
habanalabs: add more protection of device during reset
habanalabs: flush EQ workers in hard reset
habanalabs: make the reset code more consistent
habanalabs: expose reset counters via existing INFO IOCTL
habanalabs: make code more concise
habanalabs: use defines for F/W files
habanalabs: remove prints on successful device initialization
habanalabs: remove unnecessary checks
habanalabs: invalidate MMU cache only once
habanalabs: skip VA block list update in reset flow
habanalabs: optimize MMU unmap
habanalabs: prevent read/write from/to the device during hard reset
habanalabs: split MMU properties to PCI/DRAM
habanalabs: re-factor MMU masks and documentation
habanalabs: type specific MMU cache invalidation
habanalabs: re-factor memory module code
habanalabs: export uapi defines to user-space
habanalabs: don't print error when queues are full
habanalabs: increase max jobs number to 512
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big set of USB patches for 5.5-rc1
Lots of little things in here:
- typec updates and additions
- usb-serial drivers cleanups and fixes
- misc USB drivers cleanups and fixes
- gadget drivers new features and controllers added
- usual xhci additions
- other minor changes
All of these have been in linux-next with no reported issues"
* tag 'usb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (223 commits)
usb: gadget: udc: gr_udc: create debugfs directory under usb root
usb: gadget: atmel: create debugfs directory under usb root
usb: musb: create debugfs directory under usb root
usb: serial: Fix Kconfig indentation
usb: misc: Fix Kconfig indentation
usb: gadget: Fix Kconfig indentation
usb: host: Fix Kconfig indentation
usb: dwc3: Fix Kconfig indentation
usb: gadget: configfs: Fix missing spin_lock_init()
usb-storage: Disable UAS on JMicron SATA enclosure
USB: documentation: flags on usb-storage versus UAS
USB: uas: heed CAPACITY_HEURISTICS
USB: uas: honor flag to avoid CAPACITY16
usb: host: xhci-tegra: Correct phy enable sequence
usb-serial: cp201x: support Mark-10 digital force gauge
usb: chipidea: imx: pinctrl for HSIC is optional
usb: chipidea: imx: refine the error handling for hsic
usb: chipidea: imx: change hsic power regulator as optional
usb: chipidea: imx: check data->usbmisc_data against NULL before access
usb: chipidea: core: change vbus-regulator as optional
...
|
|
Add dependency from TI_CPSW_SWITCHDEV.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The px30 soc from Rockchip shares the same register description as
the rk3328, so can re-use its definitions.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Commit f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
switched from extcon_register_notifier() to the resource-managed
API, i.e. devm_extcon_register_notifier().
This is problematic in this case, because the extcon notifier
is dynamically registered/unregistered whenever the PHY is powered
on/off. The resource-managed API does not unregister the notifier
until the driver is removed, so as soon as the PHY is power cycled,
attempting to register the notifier again results in:
double register detected
WARNING: CPU: 1 PID: 182 at kernel/notifier.c:26 notifier_chain_register+0x74/0xa0
Call trace:
...
extcon_register_notifier+0x74/0xb8
devm_extcon_register_notifier+0x54/0xb8
qcom_usb_hs_phy_power_on+0x1fc/0x208
...
... and USB stops working after plugging the cable out and in
another time.
The easiest way to fix this is to make a partial revert of
commit f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
and avoid using the resource-managed API in this case.
Fixes: f0b5c2c96370 ("phy: qcom-usb-hs: Replace the extcon API")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Fix the below smatch warning by adding variable check rather than the
hardcoded value.
warn: array off by one? 'data->select_value[channel_num]'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
ltq_vrx200_pcie_phy_power_on()
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: e52a632195bf ("phy: lantiq: vrx200-pcie: add a driver for the Lantiq VRX200 PCIe PHY")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The Innosilicon Video Combo PHY not only supports MIPI DSI,
but also LVDS and TTL functions with small die size and low
pin count. Customers can choose according to their own applications.
Signed-off-by: Wyon Bi <bivvy.bi@rock-chips.com>
[removed TTL mode for now, as it required a hook back into the dsi host]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Allwinner H6 SoC contains a USB3 PHY (with USB2 DP/DM lines also
controlled).
Add a driver for it.
The register operations in this driver is mainly extracted from the BSP
USB3 driver.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
SM8150 UFS PHY is v4 of QMP phy. Add support for V4 QMP phy register
defines and support for SM8150 QMP UFS PHY.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Now phy-gmii-sel will disable MAC TX internal delay for PHY interface mode
"rgmii-rxid" which is incorrect.
Hence, fix it by enabling MAC TX internal delay in the case of "rgmii-rxid"
mode.
Fixes: 92b58b34741f ("phy: ti: introduce phy-gmii-sel driver")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use the new regulator helper instead of a for loop.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/phy/ti/phy-dm816x-usb.c:192:29: warning:
variable phy_data set but not used [-Wunused-but-set-variable]
It is never used, so can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Since the role_store() uses strncmp(), it's possible to refer
out-of-memory if the sysfs data size is smaller than strlen("host").
This patch fixes it by using sysfs_streq() instead of strncmp().
Reported-by: Pavel Machek <pavel@denx.de>
Fixes: 9bb86777fb71 ("phy: rcar-gen3-usb2: add sysfs for usb role swap")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Tegra XUSB device control driver needs to control vbus override
during its operations, add API for the support.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
On Tegra210, usb2 only otg/peripheral ports dont work in device mode.
They need an assosciated usb3 port to work in device mode. Identify
an unused usb3 port and assign it as a fake USB3 port to USB2 only
port whose mode is otg/peripheral.
Based on work by BH Hsieh <bhsieh@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Configure the port capabilities based on usb_dr_mode settings.
Based on work by JC Kuo <jckuo@nvidia.com>.
Signed-off-by: Nagarjuna Kristam <nkristam@nvidia.com>
Reviewed-by: JC Kuo <jckuo@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The xhci_ec_base variable is a pointer, so don't compare
it with an integer.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The register address should have __iomem attributes
so fix this to remove the following sparse warnings:
drivers/phy/broadcom/phy-brcm-usb-init.c:459:30: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:459:30: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:459:30: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:459:30: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:461:30: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:461:30: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:461:30: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:461:30: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:465:30: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:465:30: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:465:30: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:465:30: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:469:30: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:469:30: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:469:30: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:469:30: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:478:30: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:478:30: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:478:30: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:478:30: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:480:30: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:480:30: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:480:30: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:480:30: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:485:30: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:485:30: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:485:30: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:485:30: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:494:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:494:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:494:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:494:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:495:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:495:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:495:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:495:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:498:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:498:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:498:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:498:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:501:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:501:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:501:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:501:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:613:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:613:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:613:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:613:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:640:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:640:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:640:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:640:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:710:64: warning: Using plain integer as NULL pointer
drivers/phy/broadcom/phy-brcm-usb-init.c:712:32: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:712:32: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:712:32: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:712:32: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:713:29: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:713:29: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:713:29: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:713:29: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:717:29: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:717:29: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:717:29: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:717:29: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:720:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:720:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:720:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:720:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:721:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:721:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:721:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:721:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:794:29: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:794:29: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:794:29: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:794:29: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:813:29: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:813:29: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:813:29: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:813:29: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:829:37: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:829:37: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:829:37: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:829:37: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:843:37: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:843:37: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:843:37: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:843:37: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:847:37: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:847:37: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:847:37: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:847:37: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:878:9: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:878:9: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:878:9: expected void [noderef] <asn:2> *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:878:9: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:880:29: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:880:29: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:880:29: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:880:29: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:896:29: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:896:29: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:896:29: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:896:29: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:901:37: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:901:37: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:901:37: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:901:37: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:905:37: warning: cast removes address space '<asn:2>' of expression
drivers/phy/broadcom/phy-brcm-usb-init.c:905:37: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:905:37: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:905:37: got void *
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:423:52: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: warning: incorrect type in assignment (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: expected void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:434:13: got void [noderef] <asn:2> *
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: warning: incorrect type in argument 1 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:38: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: warning: incorrect type in argument 2 (different address spaces)
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: expected void [noderef] <asn:2> *addr
drivers/phy/broadcom/phy-brcm-usb-init.c:435:51: got void *reg
drivers/phy/broadcom/phy-brcm-usb-init.c:422:13: warning: too many warnings
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:
phy_rcar_gen3_usb2 ee0a0200.usb-phy: IRQ index 0 not found
Fix this by calling platform_get_irq_optional() instead.
Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
mvebu_a3700_utmi_phy_probe()
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The local variable @priv is set but not used, can be removed
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Don't populate the array serdes_reg on the stack but instead make it
static const. Makes the object code smaller by 228 bytes.
Before:
text data bss dec hex filename
23875 6232 64 30171 75db drivers/phy/phy-xgene.o
After:
text data bss dec hex filename
23551 6328 64 29943 74f7 drivers/phy/phy-xgene.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
As platform_get_irq() now prints an error when the interrupt does not
exist, a scary warning may be printed for an optional interrupt:
phy_rcar_gen3_usb2 ee0a0200.usb-phy: IRQ index 0 not found
Fix this by calling platform_get_irq_optional() instead.
Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()")
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add PHY driver for the USB2 PHY found on Marvell MMP3 SoC.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
This adds extended PCIe PHY functions for the Amlogic G12A
USB3+PCIE Combo PHY to support reset, power_on and power_off for
PCIe exclusively.
With these callbacks, we can handle all the needed operations of the
Amlogic PCIe controller driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Consolidate _HPP/_HPX stuff in pci-acpi.c and simplify it
(Krzysztof Wilczynski)
- Fix incorrect PCIe device types and remove dev->has_secondary_link
to simplify code that deals with upstream/downstream ports (Mika
Westerberg)
- After suspend, restore Resizable BAR size bits correctly for 1MB
BARs (Sumit Saxena)
- Enable PCI_MSI_IRQ_DOMAIN support for RISC-V (Wesley Terpstra)
Virtualization:
- Add ACS quirks for iProc PAXB (Abhinav Ratna), Amazon Annapurna
Labs (Ali Saidi)
- Move sysfs SR-IOV functions to iov.c (Kelsey Skunberg)
- Remove group write permissions from sysfs sriov_numvfs,
sriov_drivers_autoprobe (Kelsey Skunberg)
Hotplug:
- Simplify pciehp indicator control (Denis Efremov)
Peer-to-peer DMA:
- Allow P2P DMA between root ports for whitelisted bridges (Logan
Gunthorpe)
- Whitelist some Intel host bridges for P2P DMA (Logan Gunthorpe)
- DMA map P2P DMA requests that traverse host bridge (Logan
Gunthorpe)
Amazon Annapurna Labs host bridge driver:
- Add DT binding and controller driver (Jonathan Chocron)
Hyper-V host bridge driver:
- Fix hv_pci_dev->pci_slot use-after-free (Dexuan Cui)
- Fix PCI domain number collisions (Haiyang Zhang)
- Use instance ID bytes 4 & 5 as PCI domain numbers (Haiyang Zhang)
- Fix build errors on non-SYSFS config (Randy Dunlap)
i.MX6 host bridge driver:
- Limit DBI register length (Stefan Agner)
Intel VMD host bridge driver:
- Fix config addressing issues (Jon Derrick)
Layerscape host bridge driver:
- Add bar_fixed_64bit property to endpoint driver (Xiaowei Bao)
- Add CONFIG_PCI_LAYERSCAPE_EP to build EP/RC drivers separately
(Xiaowei Bao)
Mediatek host bridge driver:
- Add MT7629 controller support (Jianjun Wang)
Mobiveil host bridge driver:
- Fix CPU base address setup (Hou Zhiqiang)
- Make "num-lanes" property optional (Hou Zhiqiang)
Tegra host bridge driver:
- Fix OF node reference leak (Nishka Dasgupta)
- Disable MSI for root ports to work around design problem (Vidya
Sagar)
- Add Tegra194 DT binding and controller support (Vidya Sagar)
- Add support for sideband pins and slot regulators (Vidya Sagar)
- Add PIPE2UPHY support (Vidya Sagar)
Misc:
- Remove unused pci_block_cfg_access() et al (Kelsey Skunberg)
- Unexport pci_bus_get(), etc (Kelsey Skunberg)
- Hide PM, VC, link speed, ATS, ECRC, PTM constants and interfaces in
the PCI core (Kelsey Skunberg)
- Clean up sysfs DEVICE_ATTR() usage (Kelsey Skunberg)
- Mark expected switch fall-through (Gustavo A. R. Silva)
- Propagate errors for optional regulators and PHYs (Thierry Reding)
- Fix kernel command line resource_alignment parameter issues (Logan
Gunthorpe)"
* tag 'pci-v5.4-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (112 commits)
PCI: Add pci_irq_vector() and other stubs when !CONFIG_PCI
arm64: tegra: Add PCIe slot supply information in p2972-0000 platform
arm64: tegra: Add configuration for PCIe C5 sideband signals
PCI: tegra: Add support to enable slot regulators
PCI: tegra: Add support to configure sideband pins
PCI: vmd: Fix shadow offsets to reflect spec changes
PCI: vmd: Fix config addressing when using bus offsets
PCI: dwc: Add validation that PCIe core is set to correct mode
PCI: dwc: al: Add Amazon Annapurna Labs PCIe controller driver
dt-bindings: PCI: Add Amazon's Annapurna Labs PCIe host bridge binding
PCI: Add quirk to disable MSI-X support for Amazon's Annapurna Labs Root Port
PCI/VPD: Prevent VPD access for Amazon's Annapurna Labs Root Port
PCI: Add ACS quirk for Amazon Annapurna Labs root ports
PCI: Add Amazon's Annapurna Labs vendor ID
MAINTAINERS: Add PCI native host/endpoint controllers designated reviewer
PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbers
dt-bindings: PCI: tegra: Add PCIe slot supplies regulator entries
dt-bindings: PCI: tegra: Add sideband pins configuration entries
PCI: tegra: Add Tegra194 PCIe support
PCI: Get rid of dev->has_secondary_link flag
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Ensure HWMON devices are registered with valid names
- Fix device wakeup code
Drivers:
- bq25890_charger: Add BQ25895 support
- axp288_fuel_gauge: Add Minix Neo Z83-4 to blacklist
- sc27xx: improve battery calibration
- misc small fixes all over drivers"
* tag 'for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (24 commits)
power: supply: cpcap-charger: Enable vbus boost voltage
power: supply: sc27xx: Add POWER_SUPPLY_PROP_CALIBRATE attribute
power: supply: sc27xx: Optimize the battery capacity calibration
power: supply: sc27xx: Make sure the alarm capacity is larger than 0
power: supply: sc27xx: Fix the the accuracy issue of coulomb calculation
power: supply: sc27xx: Fix conditon to enable the FGU interrupt
power: supply: sc27xx: Add POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN attribute
power: supply: max77650: add MODULE_ALIAS()
power: supply: isp1704: remove redundant assignment to variable ret
power: supply: bq25890_charger: Add the BQ25895 part
power: supply: sc27xx: Replace devm_add_action() followed by failure action with devm_add_action_or_reset()
power: supply: sc27xx: Introduce local variable 'struct device *dev'
power: reset: reboot-mode: Fix author email format
power: supply: ab8500: remove set but not used variables 'vbup33_vrtcn' and 'bup_vch_range'
power: supply: max17042_battery: Fix a typo in function names
power: reset: gpio-restart: Fix typo when gpio reset is not found
power: supply: Init device wakeup after device_add()
power: supply: ab8500_charger: Mark expected switch fall-through
power: supply: sbs-battery: only return health when battery present
MAINTAINERS: N900: Remove isp1704_charger.h record
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"We have a small collection of core framework updates this time, mostly
around clk registration by clk providers and debugfs "nice to haves"
for rate constraints. I'll highlight that we're now setting the
clk_init_data pointer inside struct clk_hw to NULL during
clk_register(), which may break some drivers that thought they could
use that pointer during normal operations. That change has been
sitting in next for a while now but maybe something is still broken.
We'l see. Other than that the core framework changes aren't invasive
and they're fixing bugs, simplifying, and making things better.
On the clk driver side we got the usual addition of new SoC support,
new features for existing drivers, and bug fixes scattered throughout.
The biggest diffstat is the Amlogic driver that gained CPU clk support
in addition to migrating to the new way of specifying clk parents.
After that the Qualcomm, i.MX, Mediatek, and Rockchip clk drivers got
support for various new SoCs and clock controllers from those vendors.
Core:
- Drop NULL checks in clk debugfs
- Add min/max rates to clk debugfs
- Set clk_init_data pointer inside clk_hw to NULL after registration
- Make clk_bulk_get_all() return an 'id' corresponding to clock-names
- Evict parents from parent cache when they're unregistered
New Drivers:
- Add clock driver for i.MX8MN SoCs
- Support aspeed AST2600 SoCs
- Support for Mediatek MT6779 SoCs
- Support qcom SM8150 GCC and RPMh clks
- Support qcom QCS404 WCSS clks
- Add CPU clock support for Armada 7K/8K (specifically AP806 and AP807)
- Addition of clock driver for Rockchip rk3308 SoCs
Updates:
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Add SDIO gate support to aspeed driver
- Add missing of_node_put() calls in various clk drivers
- Migrate Amlogic driver to new clock parent description method
- Add DVFS support to Amlogic Meson g12
- Add Amlogic Meson g12a reset support to the axg audio clock controller
- Add sm1 support to the Amlogic Meson g12a clock controller
- Switch i.MX8MM clock driver to platform driver
- Add Hifi4 DSP related clocks for i.MX8QXP SoC
- Fix Audio PLL setting and parent clock for USB
- Misc i.MX8 clock driver improvements and corrections
- Set floor ops for Qualcomm SD clks so that rounding works
- Fix "always-on" Clock Domains on Renesas R-Car M1A, RZ/A1, RZ/A2, and RZ/N1
- Enable the Allwinner V3 SoC and fix the i2s clock for H6"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (137 commits)
clk: Drop !clk checks in debugfs dumping
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: mvebu: ap80x: add AP807 clock support
clk: mvebu: ap806: Prepare the introduction of AP807 clock support
clk: mvebu: ap806: add AP-DCLK (hclk) to system controller driver
clk: mvebu: ap806: be more explicit on what SaR is
clk: mvebu: ap80x-cpu: add AP807 CPU clock support
clk: mvebu: ap806-cpu: prepare mapping of AP807 CPU clock
dt-bindings: ap806: Document AP807 clock compatible
dt-bindings: ap80x: Document AP807 CPU clock compatible
clk: sprd: add missing kfree
clk: at91: allow 24 Mhz clock as input for PLL
clk: Make clk_bulk_get_all() return a valid "id"
clk: actions: Fix factor clk struct member access
clk: qcom: rcg: Return failure for RCG update
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
...
|
|
We are currently not enabling VBUS boost for cpcap when in host mode.
This means the VBUS is fed at the battery voltage level, which can cause
flakeyness enumerating devices.
Looks like the boost control for VBUS is CPCAP_BIT_VBUS_SWITCH that we
must enable in the charger for nice 4.92 V VBUS output. And looks like
we must not use the STBY pin enabling but must instead use manual VBUS
control in phy-cpcap-usb.
We want to do this in cpcap_charger_vbus_work() and also set a flag for
feeding_vbus to avoid races between USB detection and charger detection,
and disable charging if feeding_vbus is set.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The documentation for Marvell's cp110 phy refers to these
registers/register regions as DTL control, DTL frequency loop enable,
etc. This patch aligns the relevant code for these accordingly.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Marvell's cp110 phy supports RXAUI on lanes 2, 3, 4, and 5 when
connected to port zero. When used in this mode, lanes operate in pairs
of two (2 and 3, 4 and 5).
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Now that all COMPHY modes are supported by the driver, update the
comment stating that mvebu_comphy_power_off() should be called for
each lane. This is still wrong because for compatibility reasons, it
might break users running an old firmware (the driver only uses SMC
calls for SATA, USB and PCIe configuration, there is no code in Linux
to fallback on in these cases.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add PCIe support by filling the COMPHY modes table.
Also add a new macro to generate the right value for the firmware
depending on the width (PCI x1, x2, x4, etc). The width will be passed
by the core as the "submode" argument of the ->set_mode() callback. If
this argument is zero, default to x1 mode.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Before adding more logic, simplify a bit the writing of the
mvebu_comphy_get_mode() helper by using a pointer instead of
referencing a configuration with the entire table name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add the corresponding entries in the COMPHY modes table.
SATA support does not need any additional care.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add USB3 host/device support by adding the right entries in the COMPHY
modes table. A new macro is created to instantiate a "generic" mode
ie. not an Ethernet one. This macro will be re-used when adding SATA
support.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The COMPHY can configure the SERDES lanes in several non-Ethernet
modes: SATA, USB3, PCIe. Drop the condition limiting the driver to
Ethernet modes only before adding support for more.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
