| Age | Commit message (Collapse) | Author |
|---|
|
Replace hardcoded 'gbe_phy_init' array size by explicit one.
Fixes: 934337080c6c ("phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation")
Signed-off-by: Mikhail Kobuk <m.kobuk@ispras.ru>
Link: https://lore.kernel.org/r/20240321164734.49273-2-m.kobuk@ispras.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
There is an out of bounds read access of 'gbe_phy_init_fix[fix_idx].addr'
every iteration after 'fix_idx' reaches 'ARRAY_SIZE(gbe_phy_init_fix)'.
Make sure 'gbe_phy_init[addr]' is used when all elements of
'gbe_phy_init_fix' array are handled.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 934337080c6c ("phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation")
Signed-off-by: Mikhail Kobuk <m.kobuk@ispras.ru>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20240321164734.49273-1-m.kobuk@ispras.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The xlate callbacks are supposed to translate of_phandle_args to proper
provider without modifying the of_phandle_args. Make the argument
pointer to const for code safety and readability.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Florian Fainelli <florian.fainelli@broadcom.com> #Broadcom
Link: https://lore.kernel.org/r/20240217093937.58234-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Armada 38x supports 3 functions on serdes #0:
- pcie port 0
- sata port 0
- gbe port 0
Add missing entry for gbe port 0 on serdes 0 to the gbe_mux array.
Because this array looks obscure to new readers, also add a comment
explaining the meaning of rows, columns and values.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Link: https://lore.kernel.org/r/20240106-fix-a38x-comphy-sd0-gbe0-v1-1-c7fd87272050@solid-run.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Use preferred device_get_match_data() instead of of_match_device() to
get the driver match data. With this, adjust the includes to explicitly
include the correct headers.
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20231009172923.2457844-15-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
'version' is an enum, thus cast of pointer on 64-bit compile test with
W=1 causes:
phy-pxa-usb.c:299:26: error: cast to smaller integer type 'enum pxa_usb_phy_version' from 'const void *' [-Werror,-Wvoid-pointer-to-enum-cast]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230810111958.205705-4-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/phy/phy-can-transceiver.c
Acked-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20230714174841.4061919-1-robh@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
devm_platform_get_and_ioremap_resource()
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Yangtao Li <frank.li@vivo.com>
Link: https://lore.kernel.org/r/20230705090126.26854-1-frank.li@vivo.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might not be relevant here). This
also fixes !CONFIG_OF error:
drivers/phy/marvell/phy-pxa-28nm-hsic.c:192:34: error: ‘mv_hsic_phy_dt_match’ defined but not used [-Werror=unused-const-variable=]
drivers/phy/marvell/phy-pxa-28nm-usb2.c:324:34: error: ‘mv_usbphy_dt_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230312132611.352654-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Link: https://lore.kernel.org/r/202211171411439883050@zte.com.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
power on
Turris MOX board with older ARM Trusted Firmware version v1.5 is not able
to detect any USB 3.0 device connected to USB-A port on Mox-A module after
commit 0a6fc70d76bd ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken
reset support"). On the other hand USB 2.0 devices connected to the same
USB-A port are working fine.
It looks as if the older firmware configures COMPHY registers for USB 3.0
somehow incompatibly for kernel driver. Experiments show that resetting
COMPHY registers via setting SFT_RST auto-clearing bit in COMPHY_SFT_RESET
register fixes this issue.
Reset the COMPHY in mvebu_a3700_comphy_usb3_power_on() function as a first
step after selecting COMPHY lane and USB 3.0 function. With this change
Turris MOX board can successfully detect USB 3.0 devices again.
Before the above mentioned commit this reset was implemented in PHY reset
method, so this is the reason why there was no issue with older firmware
version then.
Fixes: 0a6fc70d76bd ("phy: marvell: phy-mvebu-a3700-comphy: Remove broken reset support")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20220920121154.30115-1-pali@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Reset support for SATA PHY is somehow broken and after calling it, kernel
is not able to detect and initialize SATA disk Samsung SSD 850 EMT0 [1].
Reset support was introduced in commit 934337080c6c ("phy: marvell:
phy-mvebu-a3700-comphy: Add native kernel implementation") as part of
complete rewrite of this driver. v1 patch series of that commit [2] did
not contain reset support and was tested that is working fine with
Ethernet, SATA and USB PHYs without issues too.
So for now remove broken reset support and change implementation of
power_off callback to power off all functions on specified lane (and not
only selected function) because during startup kernel does not know which
function was selected and configured by bootloader. Same logic was used
also in v1 patch series of that commit.
This change fixes issues with initialization of SATA disk Samsung SSD 850
and disk is working again, like before mentioned commit.
Once problem with PHY reset callback is solved its functionality could be
re-introduced. But for now it is unknown why it does not work.
[1] - https://lore.kernel.org/r/20220531124159.3e4lgn2v462irbtz@shindev/
[2] - https://lore.kernel.org/r/20211028184242.22105-1-kabel@kernel.org/
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Fixes: 934337080c6c ("phy: marvell: phy-mvebu-a3700-comphy: Add native kernel implementation")
Cc: stable@vger.kernel.org # v5.18+
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20220829083046.15082-1-pali@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Remove old RPC implementation and add a new native kernel implementation.
The old implementation uses ARM SMC API to issue RPC calls to ARM Trusted
Firmware which provides real implementation of PHY configuration.
But older versions of ARM Trusted Firmware do not provide this PHY
configuration functionality, simply returning: operation not supported; or
worse, some versions provide the configuration functionality incorrectly.
For example the firmware shipped in ESPRESSObin board has this older
version of ARM Trusted Firmware and therefore SATA, USB 3.0 and PCIe
functionality do not work with newer versions of Linux kernel.
Due to the above reasons, the following commits were introduced into Linux,
to workaround these issues by ignoring -EOPNOTSUPP error code from
phy-mvebu-a3700-comphy driver function phy_power_on():
commit 45aefe3d2251 ("ata: ahci: mvebu: Make SATA PHY optional for Armada
3720")
commit 3241929b67d2 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for
Armada 3720")
commit b0c6ae0f8948 ("PCI: aardvark: Fix initialization with old Marvell's
Arm Trusted Firmware")
Replace this RPC implementation with proper native kernel implementation,
which is independent on the firmware. Never return -EOPNOTSUPP for proper
arguments.
This should solve multiple issues with real-world boards, where it is not
possible or really inconvenient to change the firmware. Let's eliminate
these issues.
This implementation is ported directly from Armada 3720 comphy driver found
in newest version of ARM Trusted Firmware source code, but with various
fixes of register names, some added comments, some refactoring due to the
original code not conforming to kernel standards. Also PCIe mode poweroff
support was added here, and PHY reset support. These changes are also going
to be sent to ARM Trusted Firmware.
[ Pali did the porting from ATF.
I (Marek) then fixed some register names, some various other things,
added some comments and refactored the code to kernel standards. Also
fixed PHY poweroff and added PHY reset. ]
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220203214444.1508-3-kabel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Port number is encoded into argument for SMC call. It is zero for SATA,
PCIe and also both USB 3.0 PHYs. It is non-zero only for Ethernet PHY
(incorrectly called SGMII) on lane 0. Ethernet PHY on lane 1 also uses zero
port number.
So construct "port" bits for SMC call argument can be constructed directly
from PHY type and lane number.
Change driver code to always pass zero port number for non-ethernet PHYs
and for ethernet PHYs determinate port number from lane number. This
simplifies the driver.
As port number from DT PHY configuration is not used anymore, remove whole
driver code which parses it. This also simplifies the driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220203214444.1508-2-kabel@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
No conflicts.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for PHY_INTERFACE_MODE_5GBASER mode within the Marvell CP110
common PHY driver.
This is currently only supported via SMC calls to TF-A. Legacy support
may be added later, if needed.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the format and add description for ops to fix the below warnings:
drivers/phy/marvell/phy-mvebu-cp110-utmi.c:94: warning: Function parameter or member 'syscon' not described in 'mvebu_cp110_utmi'
drivers/phy/marvell/phy-mvebu-cp110-utmi.c:94: warning: Function parameter or member 'ops' not described in 'mvebu_cp110_utmi'
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20211116103951.34482-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Armada 3700 does not support RXAUI, XFI and neither SFI. Remove unused
macros for these unsupported modes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 9695375a3f4a ("phy: add A3700 COMPHY support")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Comphy phy mode 0x3 is incorrectly named. It is not SGMII but rather
2500Base-X mode which runs at 3.125 Gbps speed.
Rename macro names and comments to 2500Base-X.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 9695375a3f4a ("phy: add A3700 COMPHY support")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Comphy phy mode 0x3 is incorrectly named. It is not SGMII but rather
2500Base-X mode which runs at 3.125 Gbps speed.
Rename macro names and comments to 2500Base-X.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: eb6a1fcb53e2 ("phy: mvebu-cp110-comphy: Add SMC call support")
Fixes: c2afb2fef595 ("phy: mvebu-cp110-comphy: Rename the macro handling only Ethernet modes")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: He Ying <heying24@huawei.com>
Link: https://lore.kernel.org/r/20210408090806.247325-1-heying24@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
When USB and USB_COMMON are not enabled, phy-mvebu-cp110-utmi
suffers a build error due to a missing interface that is provided
by CONFIG_USB_COMMON, so make the driver depend on USB_COMMON.
ld: drivers/phy/marvell/phy-mvebu-cp110-utmi.o: in function `mvebu_cp110_utmi_phy_probe':
phy-mvebu-cp110-utmi.c:(.text+0x152): undefined reference to `of_usb_get_dr_mode_by_phy'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: linux-phy@lists.infradead.org
Link: https://lore.kernel.org/r/20210401210045.23525-1-rdunlap@infradead.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of ARMADA375_USBCLUSTER_PHY
to MACH_ARMADA_375, and ask the user in case of compile-testing.
Fixes: eee47538ec1f2619 ("phy: add support for USB cluster on the Armada 375 SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210208150252.424706-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for Marvell CP110 UTMI PHY driver allowing the USB2
port configuration independently from the boot loader setup.
The CP110/CP115 dies have 2 UTMI PHYs that could be connected
to two USB host controllers or to single USB device controller.
Since there is only one USB device controller on die, only one
of the UTMI PHYs could work in USB device mode.
The CONFIG_PHY_MVEBU_CP110_UTMI should be enabled for usage of
this driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Link: https://lore.kernel.org/r/20210307163343.25684-2-kostap@marvell.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Use devm_platform_ioremap_resource to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/1604642930-29019-7-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add PHY driver for the HSICs found on Marvell MMP3 SoC. The driver is
rather straightforward -- the PHY essentially just needs to be enabled.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20200925235828.228626-4-lkundrak@v3.sk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Print IRQ number used by PCIe Link Bandwidth Notification (Dongdong
Liu)
- Add schedule point in pci_read_config() to reduce max latency
(Jiang Biao)
- Add Kconfig options for MPS/MRRS strategy (Jim Quinlan)
Resource management:
- Fix pci_iounmap() memory leak when !CONFIG_GENERIC_IOMAP (Lorenzo
Pieralisi)
PCIe native device hotplug:
- Reduce noisiness on hot removal (Lukas Wunner)
Power management:
- Revert "PCI/PM: Apply D2 delay as milliseconds, not microseconds"
that was done on the basis of spec typo (Bjorn Helgaas)
- Rename pci_dev.d3_delay to d3hot_delay to remove D3hot/D3cold
ambiguity (Krzysztof Wilczyński)
- Remove unused pcibios_pm_ops (Vaibhav Gupta)
IOMMU:
- Enable Translation Blocking for external devices to harden against
DMA attacks (Rajat Jain)
Error handling:
- Add an ACPI APEI notifier chain for vendor CPER records to enable
device-specific error handling (Shiju Jose)
ASPM:
- Remove struct aspm_register_info to simplify code (Saheed O.
Bolarinwa)
Amlogic Meson PCIe controller driver:
- Build as module by default (Kevin Hilman)
Ampere Altra PCIe controller driver:
- Add MCFG quirk to work around non-standard ECAM implementation
(Tuan Phan)
Broadcom iProc PCIe controller driver:
- Set affinity mask on MSI interrupts (Mark Tomlinson)
Broadcom STB PCIe controller driver:
- Make PCIE_BRCMSTB depend on ARCH_BRCMSTB (Jim Quinlan)
- Add DT bindings for more Brcmstb chips (Jim Quinlan)
- Add bcm7278 register info (Jim Quinlan)
- Add bcm7278 PERST# support (Jim Quinlan)
- Add suspend and resume pm_ops (Jim Quinlan)
- Add control of rescal reset (Jim Quinlan)
- Set additional internal memory DMA viewport sizes (Jim Quinlan)
- Accommodate MSI for older chips (Jim Quinlan)
- Set bus max burst size by chip type (Jim Quinlan)
- Add support for bcm7211, bcm7216, bcm7445, bcm7278 (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Use dev_err_probe() to reduce redundant messages (Anson Huang)
Freescale Layerscape PCIe controller driver:
- Enforce 4K DMA buffer alignment in endpoint test (Hou Zhiqiang)
- Add DT compatible strings for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint support for ls1088a, ls2088a (Xiaowei Bao)
- Add endpoint test support for lS1088a (Xiaowei Bao)
- Add MSI-X support for ls1088a (Xiaowei Bao)
HiSilicon HIP PCIe controller driver:
- Handle HIP-specific errors via ACPI APEI (Yicong Yang)
HiSilicon Kirin PCIe controller driver:
- Return -EPROBE_DEFER if the GPIO isn't ready (Bean Huo)
Intel VMD host bridge driver:
- Factor out physical offset, bus offset, IRQ domain, IRQ allocation
(Jon Derrick)
- Use generic PCI PM correctly (Jon Derrick)
Marvell Aardvark PCIe controller driver:
- Fix compilation on s390 (Pali Rohár)
- Implement driver 'remove' function and allow to build it as module
(Pali Rohár)
- Move PCIe reset card code to advk_pcie_train_link() (Pali Rohár)
- Convert mvebu a3700 internal SMCC firmware return codes to errno
(Pali Rohár)
- Fix initialization with old Marvell's Arm Trusted Firmware (Pali
Rohár)
Microsoft Hyper-V host bridge driver:
- Fix hibernation in case interrupts are not re-created (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Stop checking return value of debugfs_create() functions (Greg
Kroah-Hartman)
- Convert to use DEFINE_SEQ_ATTRIBUTE macro (Liu Shixin)
Qualcomm PCIe controller driver:
- Reset PCIe to work around Qsdk U-Boot issue (Ansuel Smith)
Renesas R-Car PCIe controller driver:
- Add DT documentation for r8a774a1, r8a774b1, r8a774e1 endpoints
(Lad Prabhakar)
- Add RZ/G2M, RZ/G2N, RZ/G2H IDs to endpoint test (Lad Prabhakar)
- Add DT support for r8a7742 (Lad Prabhakar)
Socionext UniPhier Pro5 controller driver:
- Add DT descriptions of iATU register (host and endpoint) (Kunihiko
Hayashi)
Synopsys DesignWare PCIe controller driver:
- Add link up check in dw_child_pcie_ops.map_bus() (racy, but seems
unavoidable) (Hou Zhiqiang)
- Fix endpoint Header Type check so multi-function devices work (Hou
Zhiqiang)
- Skip PCIE_MSI_INTR0* programming if MSI is disabled (Jisheng Zhang)
- Stop leaking MSI page in suspend/resume (Jisheng Zhang)
- Add common iATU register support instead of keystone-specific code
(Kunihiko Hayashi)
- Major config space access and other cleanups in dwc core and
drivers that use it (al, exynos, histb, imx6, intel-gw, keystone,
kirin, meson, qcom, tegra) (Rob Herring)
- Add multiple PFs support for endpoint (Xiaowei Bao)
- Add MSI-X doorbell mode in endpoint mode (Xiaowei Bao)
Miscellaneous:
- Use fallthrough pseudo-keyword (Gustavo A. R. Silva)
- Fix "0 used as NULL pointer" warnings (Gustavo Pimentel)
- Fix "cast truncates bits from constant value" warnings (Gustavo
Pimentel)
- Remove redundant zeroing for sg_init_table() (Julia Lawall)
- Use scnprintf(), not snprintf(), in sysfs "show" functions
(Krzysztof Wilczyński)
- Remove unused assignments (Krzysztof Wilczyński)
- Fix "0 used as NULL pointer" warning (Krzysztof Wilczyński)
- Simplify bool comparisons (Krzysztof Wilczyński)
- Use for_each_child_of_node() and for_each_node_by_name() (Qinglang
Miao)
- Simplify return expressions (Qinglang Miao)"
* tag 'pci-v5.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (147 commits)
PCI: vmd: Update VMD PM to correctly use generic PCI PM
PCI: vmd: Create IRQ allocation helper
PCI: vmd: Create IRQ Domain configuration helper
PCI: vmd: Create bus offset configuration helper
PCI: vmd: Create physical offset helper
PCI: v3-semi: Remove unneeded break
PCI: dwc: Add link up check in dw_child_pcie_ops.map_bus()
PCI/ASPM: Remove struct pcie_link_state.l1ss
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap
PCI/ASPM: Pass L1SS Capabilities value, not struct aspm_register_info
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl1
PCI/ASPM: Remove struct aspm_register_info.l1ss_ctl2 (unused)
PCI/ASPM: Remove struct aspm_register_info.l1ss_cap_ptr
PCI/ASPM: Remove struct aspm_register_info.latency_encoding
PCI/ASPM: Remove struct aspm_register_info.enabled
PCI/ASPM: Remove struct aspm_register_info.support
PCI/ASPM: Use 'parent' and 'child' for readability
PCI/ASPM: Move LTR path check to where it's used
PCI/ASPM: Move pci_clear_and_set_dword() earlier
PCI: dwc: Fix MSI page leakage in suspend/resume
...
|
|
Driver ->power_on and ->power_off callbacks leaks internal SMCC firmware
return codes to phy caller. This patch converts SMCC error codes to
standard linux errno codes. Include file linux/arm-smccc.h already provides
defines for SMCC error codes, so use them instead of custom driver defines.
Note that return value is signed 32bit, but stored in unsigned long type
with zero padding.
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Link: https://lore.kernel.org/r/20200902144344.16684-2-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Use readl_poll_timeout() to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1598320987-25518-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Use readl_poll_timeout() to simplify code
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1598320987-25518-5-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The mvneta hardware appears to lock up in various random ways when
repeatedly switching speeds between 1G and 2.5G, which involves
reprogramming the COMPHY. It is not entirely clear why this happens,
but best guess is that reprogramming the COMPHY glitches mvneta clocks
causing the hardware to fail. It seems that rebooting resolves the
failure, but not down/up cycling the interface alone.
Various other approaches have been tried, such as trying to cleanly
power down the COMPHY and then take it back through the power up
initialisation, but this does not seem to help.
It was finally noticed that u-boot's last step when configuring a
COMPHY for "SGMII" mode was to poke at a register described as
"GBE_CONFIGURATION_REG", which is undocumented in any external
documentation. All that we have is the fact that u-boot sets a bit
corresponding to the "SGMII" lane at the end of COMPHY initialisation.
Experimentation shows that if we clear this bit prior to changing the
speed, and then set it afterwards, mvneta does not suffer this problem
on the SolidRun Clearfog when switching speeds between 1G and 2.5G.
This problem was found while script-testing phylink.
This fix also requires the corresponding change to DT to be effective.
See "ARM: dts: armada-38x: fix NETA lockup when repeatedly switching
speeds".
Fixes: 14dc100b4411 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1jxtRj-0003Tz-CG@rmk-PC.armlinux.org.uk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We get warning with W=1 build:
drivers/phy/marvell/phy-mvebu-a3700-utmi.c:84: warning: Function
parameter or member 'usb_misc' not described in 'mvebu_a3700_utmi'
Fix that by correcting the typo usb_mis
Link: https://lore.kernel.org/r/20200708132809.265967-1-vkoul@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
|
|
Some of the phy drivers can be compile tested to increase build
coverage.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200103164710.4829-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switch network drivers, phy drivers, and SFP/phylink over to use the
more correct 10GBASE-R, rather than 10GBASE-KR. 10GBASE-KR is backplane
ethernet, which is 10GBASE-R with autonegotiation on top, which our
current usage on the affected platforms does not have.
The only remaining user of PHY_INTERFACE_MODE_10GKR is the Aquantia
PHY, which has a separate mode for 10GBASE-KR.
For Marvell mvpp2, we detect 10GBASE-KR, and rewrite it to 10GBASE-R
for compatibility with existing DT - this is the only network driver
at present that makes use of PHY_INTERFACE_MODE_10GKR.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
|
|
mvebu_a3700_utmi_phy_probe()
Simplify this function implementation by using a known wrapper function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add PHY driver for the USB2 PHY found on Marvell MMP3 SoC.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The documentation for Marvell's cp110 phy refers to these
registers/register regions as DTL control, DTL frequency loop enable,
etc. This patch aligns the relevant code for these accordingly.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Marvell's cp110 phy supports RXAUI on lanes 2, 3, 4, and 5 when
connected to port zero. When used in this mode, lanes operate in pairs
of two (2 and 3, 4 and 5).
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Now that all COMPHY modes are supported by the driver, update the
comment stating that mvebu_comphy_power_off() should be called for
each lane. This is still wrong because for compatibility reasons, it
might break users running an old firmware (the driver only uses SMC
calls for SATA, USB and PCIe configuration, there is no code in Linux
to fallback on in these cases.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add PCIe support by filling the COMPHY modes table.
Also add a new macro to generate the right value for the firmware
depending on the width (PCI x1, x2, x4, etc). The width will be passed
by the core as the "submode" argument of the ->set_mode() callback. If
this argument is zero, default to x1 mode.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Before adding more logic, simplify a bit the writing of the
mvebu_comphy_get_mode() helper by using a pointer instead of
referencing a configuration with the entire table name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add the corresponding entries in the COMPHY modes table.
SATA support does not need any additional care.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add USB3 host/device support by adding the right entries in the COMPHY
modes table. A new macro is created to instantiate a "generic" mode
ie. not an Ethernet one. This macro will be re-used when adding SATA
support.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The COMPHY can configure the SERDES lanes in several non-Ethernet
modes: SATA, USB3, PCIe. Drop the condition limiting the driver to
Ethernet modes only before adding support for more.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Before adding support for other PHY modes (not Ethernet ones), let's
rename the MVEBU_COMPHY_CONF macro to a more specific (and shorter)
appellation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add support for RXAUI mode by adding an entry in the COMPHY modes list.
There is no user for this mode yet so we can enforce an up-to-date
firmware and return an error otherwise without breaking anywone.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Currently, the driver supports setting lanes to 1000BASEX, 2500BASEX,
10GKR. Complete the COMPHY modes list by adding two (already
supported) cases for lane 4.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Keep the exact same list of supported configurations but first try to
use the firmware's implementation. If it fails, try the legacy method:
Linux implementation.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
